CoChat

Deformation of Poly-l-lactid acid (PLLA) under Uniaxial Tension and Plane-Strain Compression

Open access
Vozniak, Alina, Bartczak, Zbigniew · 2021 · Polymers

The DOI matches its Crossref record; 59 of the 59 references it cites were found in a registry or an index.

Abstract

The ability of PLLA, either amorphous or semicrystalline, to plastic deformation to large strain was investigated in a wide temperature range (Td = 70–140 °C). Active deformation mechanisms have been identified and compared for two different deformation modes—uniaxial drawing and plane-strain compression. The initially amorphous PLLA was capable of significant deformation in both tension and plane-strain compression. In contrast, the samples of crystallized PLLA were found brittle in tensile, whereas they proved to be ductile and capable of high-strain deformation when deformed in plane-strain compression. The main deformation mechanism identified in amorphous PLLA was the orientation of chains due to plastic flow, followed by strain-induced crystallization occurring at the true strain above e = 0.5. The oriented chains in amorphous phase were then transformed into oriented mesophase and/or oriented crystals. An upper temperature limit for mesophase formation was found below Td = 90 °C. The amount of mesophase formed in this process did not exceed 5 wt.%. An additional mesophase fraction was generated at high strains from crystals damaged by severe deformation. After the formation of the crystalline phase, further deformation followed the mechanisms characteristic for the semicrystalline polymer. Interlamellar slip supported by crystallographic chain slip has been identified as the major deformation mechanism in semicrystalline PLLA. It was found that the contribution of crystallographic slip increased notably with the increase in the deformation temperature. The most probable active crystallographic slip systems were (010)[001], (100)[001] or (110)[001] slip systems operating along the chain direction. At high temperatures (Td = 115–140 °C), the α→β crystal transformation was additionally observed, leading to the formation of a small fraction of β crystals.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.3390/polym13244432

Cites

59 of 59 references verified0 citation errors · 0 not checkable

Statistics

Figures

Figure 1 Schematic drawing (a) and a photograph (b) of the channel-die compression fixture.
Figure 1 Schematic drawing (a) and a photograph (b) of the channel-die compression fixture.CC BY · PubMed Central
Figure 2 Examples of fitting the amorphous halos and mesomorphic and crystalline peaks to the scattering curve of A (a) and CC samples (b).
Figure 2 Examples of fitting the amorphous halos and mesomorphic and crystalline peaks to the scattering curve of A (a) and CC samples (b).CC BY · PubMed Central
Figure 3 DSC thermograms (a) and X-ray diffractograms (b) of initial amorphous sample A and semicrystalline sample CC, cold crystallized at 122 °C. Insets show the respective 2D-WAXS and 2D-SAXS patterns.
Figure 3 DSC thermograms (a) and X-ray diffractograms (b) of initial amorphous sample A and semicrystalline sample CC, cold crystallized at 122 °C. Insets show the respective 2D-WAXS and 2D-SAXS patterns.CC BY · PubMed Central
Figure 4 Nominal stress–nominal strain curves obtained in uniaxial tensile tests at temperatures indicated. (a) amorphous samples, A; (b) cold crystallized samples, CC. Note the different scale on the stress and strain axes in (a,b).
Figure 4 Nominal stress–nominal strain curves obtained in uniaxial tensile tests at temperatures indicated. (a) amorphous samples, A; (b) cold crystallized samples, CC. Note the different scale on the stress and strain axes in (a,b).CC BY · PubMed Central
Figure 5 True stress–true strain curves of samples deformed by plane-strain compression in a channel-die at temperatures indicated. (a) Amorphous samples, A; (b) cold crystallized samples, CC.
Figure 5 True stress–true strain curves of samples deformed by plane-strain compression in a channel-die at temperatures indicated. (a) Amorphous samples, A; (b) cold crystallized samples, CC.CC BY · PubMed Central
Figure 6 DSC heating scans of initially amorphous samples (A) drawn uniaxially at Td = 70 °C (a); 80 °C (b); and 90 °C (c), to the indicated true strain (solid lines). For each sample before deformation, a soak time of 15 min was used to equilibrate the temperature. The dashed lines represent samples that were annealed only at the respective temperature and time but were not deformed. The total residence time at the deformation or annealing temperature, ta/d, is indicated for each curve.
Figure 6 DSC heating scans of initially amorphous samples (A) drawn uniaxially at Td = 70 °C (a); 80 °C (b); and 90 °C (c), to the indicated true strain (solid lines). For each sample before deformation, a soak time of 15 min was used to equilibrate the temperature. The dashed lines represent samples that were annealed only at the respective temperature and time but were not deformed. The total residence time at the deformation or annealing temperature, ta/d, is indicated for each curve.CC BY · PubMed Central
Figure 7 DSC heating scans of initially amorphous samples (A) deformed in plane-strain compression at Td = 70 °C (a); 80 °C (b); and 90 °C (c), to the indicated true strain (solid lines). For each sample before deformation, a soak time of 15 min was used to equilibrate the temperature. The dashed lines represent samples that were annealed only at the respective temperature and time but were not deformed. The total residence time at the deformation or annealing temperature, ta/d, is indicated for each curve.
Figure 7 DSC heating scans of initially amorphous samples (A) deformed in plane-strain compression at Td = 70 °C (a); 80 °C (b); and 90 °C (c), to the indicated true strain (solid lines). For each sample before deformation, a soak time of 15 min was used to equilibrate the temperature. The dashed lines represent samples that were annealed only at the respective temperature and time but were not deformed. The total residence time at the deformation or annealing temperature, ta/d, is indicated for each curve.CC BY · PubMed Central
Figure 8 DSC heating scans of semicrystalline CC samples deformed in plane-strain compression at Td = 70 °C (a); 80 °C (b); 90 °C (c); 115 °C (d); and 140 °C (e) to the true strain indicated. The dashed line shows the thermogram of the initial CC sample, cold crystallized at T = 122 °C and not processed further. The total residence time at the deformation temperature, ta/d, is indicated for each curve.
Figure 8 DSC heating scans of semicrystalline CC samples deformed in plane-strain compression at Td = 70 °C (a); 80 °C (b); 90 °C (c); 115 °C (d); and 140 °C (e) to the true strain indicated. The dashed line shows the thermogram of the initial CC sample, cold crystallized at T = 122 °C and not processed further. The total residence time at the deformation temperature, ta/d, is indicated for each curve.CC BY · PubMed Central
Figure 9 (a) 2D-WAXS patterns of the initially amorphous A samples deformed in uniaxial tension at temperature Td = 70 °C (top row), Td = 80 °C (middle row), Td = 90 °C (bottom row) obtained in transmission with the X-ray beam illumination normal to the plane of the sample. The true strain indicated for each pattern is the local true strain calculated from the distance of the ink marks printed on the sample. (b) One-dimensional radial sections derived from 2D images along the transverse direction, TD—obtained by azimuth integration of 2D patterns in the azimuth range (−5°, +5°) around TD (ψTD = 0°).
Figure 9 (a) 2D-WAXS patterns of the initially amorphous A samples deformed in uniaxial tension at temperature Td = 70 °C (top row), Td = 80 °C (middle row), Td = 90 °C (bottom row) obtained in transmission with the X-ray beam illumination normal to the plane of the sample. The true strain indicated for each pattern is the local true strain calculated from the distance of the ink marks printed on the sample. (b) One-dimensional radial sections derived from 2D images along the transverse direction, TD—obtained by azimuth integration of 2D patterns in the azimuth range (−5°, +5°) around TD (ψTD = 0°).CC BY · PubMed Central
Figure 10 Phase composition (fraction of the crystalline phase and the mesophase) in A samples deformed by uniaxial drawing and the reference samples subjected to annealing at the respective temperature and time equivalent to the time of deformation. (a–c): composition determined from DSC; (d–f): composition estimated from X-ray diffractograms through peak fitting procedure. The temperature of deformation or annealing: 70 °C—(a,d); 80 °C—(b,e); and 90 °C—(c,f).
Figure 10 Phase composition (fraction of the crystalline phase and the mesophase) in A samples deformed by uniaxial drawing and the reference samples subjected to annealing at the respective temperature and time equivalent to the time of deformation. (a–c): composition determined from DSC; (d–f): composition estimated from X-ray diffractograms through peak fitting procedure. The temperature of deformation or annealing: 70 °C—(a,d); 80 °C—(b,e); and 90 °C—(c,f).CC BY · PubMed Central
Figure 11 2D-SAXS patterns of the initially amorphous A samples deformed in uniaxial tension at temperature Td = 70 °C (top row), Td = 80 °C (middle row), and Td = 90 °C (bottom row). The true strain indicated for each pattern is the local true strain calculated from the distance of the ink marks printed on the sample.
Figure 11 2D-SAXS patterns of the initially amorphous A samples deformed in uniaxial tension at temperature Td = 70 °C (top row), Td = 80 °C (middle row), and Td = 90 °C (bottom row). The true strain indicated for each pattern is the local true strain calculated from the distance of the ink marks printed on the sample.CC BY · PubMed Central
Figure 12 (a) Transmission 2D-WAXS patterns of the initially amorphous A samples deformed in the plane-strain compression at temperature Td = 70 °C (top row), Td = 80 °C (middle row), and Td = 90 °C (bottom row), to the indicated true strain. The patterns on the left (on a black background) were obtained in the CD-view (X-ray illumination along the CD, image plane perpendicular to it). The column on the right (gray background) shows the patterns collected in the LD-view. The white arrows indicate positions of the maxima in the (200)/(110) reflection, while the green arrows mark the weak maxima related to the (0010) and (1010) reflections. (b) One-dimensional radial sections derived from CD-view images along the loading direction, LD—obtained by azimuth integration of 2D patterns in the azimuth range (−5°, +5°) around LD (ψLD = 0°).
Figure 12 (a) Transmission 2D-WAXS patterns of the initially amorphous A samples deformed in the plane-strain compression at temperature Td = 70 °C (top row), Td = 80 °C (middle row), and Td = 90 °C (bottom row), to the indicated true strain. The patterns on the left (on a black background) were obtained in the CD-view (X-ray illumination along the CD, image plane perpendicular to it). The column on the right (gray background) shows the patterns collected in the LD-view. The white arrows indicate positions of the maxima in the (200)/(110) reflection, while the green arrows mark the weak maxima related to the (0010) and (1010) reflections. (b) One-dimensional radial sections derived from CD-view images along the loading direction, LD—obtained by azimuth integration of 2D patterns in the azimuth range (−5°, +5°) around LD (ψLD = 0°).CC BY · PubMed Central
Figure 13 Phase composition (fraction of the crystalline phase and the mesophase) in A and CC samples deformed by plane-strain compression and the reference samples subjected to annealing at the respective temperature and time equivalent to the time of deformation. (a–c,g,h): composition determined from DSC; (d–f,i,j): composition estimated from X-ray diffractograms through peak fitting procedure. The temperature of deformation or annealing: 70 °C—(a,d); 80 °C—(b,e); 90 °C—(c,f); 115 °C—(g,i); and 140 °C—(h,j).
Figure 13 Phase composition (fraction of the crystalline phase and the mesophase) in A and CC samples deformed by plane-strain compression and the reference samples subjected to annealing at the respective temperature and time equivalent to the time of deformation. (a–c,g,h): composition determined from DSC; (d–f,i,j): composition estimated from X-ray diffractograms through peak fitting procedure. The temperature of deformation or annealing: 70 °C—(a,d); 80 °C—(b,e); 90 °C—(c,f); 115 °C—(g,i); and 140 °C—(h,j).CC BY · PubMed Central
Figure 14 2D-SAXS patterns of the initially amorphous A samples deformed in the plane-strain compression at temperature Td = 70–90 °C (rows from top to bottom), to the indicated true strain. The patterns on the left (black background) were obtained in the CD-view. The patterns in the column on the right (gray background) are LD-view.
Figure 14 2D-SAXS patterns of the initially amorphous A samples deformed in the plane-strain compression at temperature Td = 70–90 °C (rows from top to bottom), to the indicated true strain. The patterns on the left (black background) were obtained in the CD-view. The patterns in the column on the right (gray background) are LD-view.CC BY · PubMed Central
Figure 15 (a) Transmission 2D-WAXS patterns of the cold crystallized CC samples deformed in the plane-strain compression at temperature Td = 70–140 °C (rows from top to bottom), to the indicated true strain. The patterns on the left (on a black background) were obtained in the CD-view. The column on the right (gray background) shows the patterns collected in the LD-view. The white arrows indicate positions of the maxima in the (200)/(110) reflection, while the green arrows mark the maxima of the (0010)/(1010) reflection. (b) One-dimensional radial sections derived from CD-view images along the loading direction, LD, obtained by azimuth integration of 2D patterns in the azimuth range (−5°, +5°) around LD (ψLD = 0°).
Figure 15 (a) Transmission 2D-WAXS patterns of the cold crystallized CC samples deformed in the plane-strain compression at temperature Td = 70–140 °C (rows from top to bottom), to the indicated true strain. The patterns on the left (on a black background) were obtained in the CD-view. The column on the right (gray background) shows the patterns collected in the LD-view. The white arrows indicate positions of the maxima in the (200)/(110) reflection, while the green arrows mark the maxima of the (0010)/(1010) reflection. (b) One-dimensional radial sections derived from CD-view images along the loading direction, LD, obtained by azimuth integration of 2D patterns in the azimuth range (−5°, +5°) around LD (ψLD = 0°).CC BY · PubMed Central
Figure 16 WAXS meridional scans of the 2D-WAXS patterns of samples deformed at Td = 140 °C to indicated strains. The experimental curves (black symbols) are compared with the ‘best fit’ curves (black lines) and their peak components (gray lines). The (003)β peak is drawn with thick blue line.
Figure 16 WAXS meridional scans of the 2D-WAXS patterns of samples deformed at Td = 140 °C to indicated strains. The experimental curves (black symbols) are compared with the ‘best fit’ curves (black lines) and their peak components (gray lines). The (003)β peak is drawn with thick blue line.CC BY · PubMed Central
Figure 17 2D-SAXS patterns of the initially amorphous A samples deformed in the plane-strain compression at temperature Td = 70–90 °C (rows from top to bottom), to the indicated true strain. The patterns on the left (black background) were obtained in the CD-view. The patterns in the column on the right (gray background) are LD-view.
Figure 17 2D-SAXS patterns of the initially amorphous A samples deformed in the plane-strain compression at temperature Td = 70–90 °C (rows from top to bottom), to the indicated true strain. The patterns on the left (black background) were obtained in the CD-view. The patterns in the column on the right (gray background) are LD-view.CC BY · PubMed Central

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 59 references

Cited by

Metadata

Authors
Vozniak, A., & Bartczak, Z.
Affiliations
Centrum Badań Molekularnych i Makromolekularnych Polskiej Akademii Nauk (PL)
Corresponding author
Bartczak, Zbigniew
Venue
Polymers
Publisher
MDPI AG
Published
2021-12-17
Volume
13
Issue
24
Pages
4432
ISSN
2073-4360 (ISSN-L)
OpenAlex
W4200576880
Cited by
11
References
59
Citations by year
2026: 4 · 2025: 2 · 2024: 3 · 2023: 1 · 2022: 1
FWCI
0.44
Type
journal article
Language
en
Open access
Locations
  • Polymers (publishedVersion, cc-by)
  • PubMed Central (publishedVersion, cc-by)
  • PubMed (publishedVersion)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
Topics
  • Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
  • Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
  • Physical Sciences › Materials Science › Metals and Alloys › Microstructure and mechanical properties
Keywords
poly(L-lactic acid), plastic deformation, uniaxial tension, plane strain compression, amorphous polymers, semicrystalline polymers, chain orientation, strain-induced crystallization, mesophase formation, deformation mechanisms, temperature dependence

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.