The DOI matches its Crossref record; 95 of the 95 references it cites were found in a registry or an index; 23 of the 84 sources its claims cite were checked for support.
Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m - b -PLLA n ) multiblock-copolymers and PDLA
Open accessAbstract
Strategic polymer synthesis and blending allows control of stereocomplexation and property fine-tuning in PLA-based materials as shown by correlative characterization.
Overview
CoChat Summary
TL;DR
This study systematically correlates block lengths in P(PCLm-b-PLLAn)x multiblock copolymers and PDLA chain length with crystalline phase formation and mechanical properties in solution-cast blends. Stereocomplex formation depends on PCL segment length as well as PLLA length, with no SC in long-PCL/short-PLLA blends, and SCs act as nucleation points for PCL crystallization while tuning ductility.
Key findings
- SC formation occurred in s/s, s/l, and l/l MBC:PDLA blends but not in l/s P(PCL113-b-PLLA26)24 blends, despite ≥21 wt% PLA; SC formed at PLLA:PDLA ratios from 1:1 up to 1:4. Reported crystallite sizes were SC 5–13 nm (conclusions also state 1–8 nm), PCL 1–20 nm, and HC 1–50 nm; relative crystallinities were SC 6–70%, PCL 2–80%, and HC 3–80%.
- SCs acted as nucleation points for PCL crystallization; SC formation was favored over PLA HC, and the HC peak disappeared when SC formed. Annealing a 90:10 MBC:PDLA56 blend increased crystal size from 4 to 12 nm and relative crystallinity from 20 to 25%, while a 50:50 blend showed no change and only 7–10% SC relative crystallinity.
- Mechanical testing showed tensile strengths up to ~2.8 MPa and elongation at break up to ~750% (table maximum 752%, range 637–768%, for P(PCL121-b-PLLA49)26:PDLA56 90:10). The 70:30 blends had the lowest elongation, while 80:20 and 90:10 compositions with SC crystallites showed the highest ductility; PDLA29 blends showed M_n-dependent ductility, whereas PDLA56 blends were governed more by composition.
- Thermal analysis found SC melting temperatures of 180–200 °C, lower than typical 200–230 °C; PCL melted at 58–63 °C and PLA HC at 140–180 °C. Total absolute crystallinity did not exceed 50%, and PDLA56 had a melting temperature of 157 °C with 66% absolute crystallinity.
Methods
- Four P(PCLm-b-PLLAn)x multiblock copolymers (s/s, s/l, l/s, l/l) and PDLA15/29/56 were synthesized, then solution-cast into films blended at MBC:PDLA ratios from 90:10 to 20:80.
- Characterization used 1H-NMR, GPC, DSC, lab and synchrotron WAXS, POM, AFM, TEM, and tensile testing in a correlative approach.
- WAXS crystallite sizes were calculated with the Scherrer equation; DSC crystallinities were calculated from melting enthalpies; tensile tests were performed at room temperature at 10 mm·min⁻¹, with results reported as average of three tests (table reports median with min–max ranges).
Limitations
- Paper states: SAXS measurements did not yield interpretable results due to insufficient electron density contrast; Scherrer analysis assumes isotropic crystallites and provides only approximate average crystallite sizes without orientation or amorphous-fraction information.
- Paper states: slow solvent evaporation may shift crystallization toward HC formation; annealing only increased SC content in samples that already contained SCs; some samples had inhomogeneities, and excessive outliers were excluded from mechanical analysis.
- Evident from text: mechanical data are based on only three tests per sample, limiting statistical power, and the accepted manuscript contains duplicated/placeholder text and some inconsistent crystallite-size reporting.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
7 Valid · 19 Not valid · 38 Not checked · 220 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Moreover, the PCL block size required for crystallization increased to more than 2000 g/mol when PLLA was crystalline.20”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > 1. Introduction
What the sources say
- Could not verifycites [20] 20. Brizzolara, D.; Cantow, H.-J.; Diederichs, K.; Keller, E.; Domb, A. J. Mechanism of the stereocomplex formation between enantiomeric poly (lactide) s. Macromolecules 1996, 29 (1), 191- 197. sourceExperimental — accuracy not yet measured
The Results and Discussion and Experimental Section (page not provided) describe crystallization of PLLA and PDLA, not PCL blocks. Searches for PCL, poly(caprolactone), and a 2000 g/mol crystallization threshold found no passage addressing the claim. (LLM, conf=0.75)
states a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Additionally, PLLA and its enantiomer PDLA can form a stereocomplex (sc-PLA).”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > 1. Introduction
What the sources say
- Could not verifycites [8] 8. Rydz, J.; Sikorska, W.; Kyulavska, M.; Christova, D. Polyester-based (bio) degradable polymers as environmentally friendly materials for sustainable development. International journal of molecular sciences 2014, 16 (1), 564-596. sourceExperimental — accuracy not yet measured
Section 4.1, Table 1 identifies PLLA as poly(l-lactide) and PDLA as poly(d-lactide), but does not say they form a stereocomplex. Searches for “stereocomplex” and for blends of the two polymers found no passage in our copy addressing stereocomplex formation; page numbers were not available. (LLM, conf=0.72)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“The structure-phase and structure-property relations in multiblock copolymers (MBCs) of PLA are not fully understood, compared to homopolymers, copolymers and DCs, though studies on other MBCs suggest similarities as well as peculiarities of MBCs compared to diblock copolymers.8,17,21”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > 1. Introduction
What the sources say
- Could not verifycites [8] 8. Rydz, J.; Sikorska, W.; Kyulavska, M.; Christova, D. Polyester-based (bio) degradable polymers as environmentally friendly materials for sustainable development. International journal of molecular sciences 2014, 16 (1), 564-596. sourceExperimental — accuracy not yet measured
Section 4.2 (page unavailable) says PLA architecture and crystallinity affect material properties, but it does not assess how well structure–phase or structure–property relations are understood for PLA multiblock copolymers. Searches for multiblock copolymers, diblock comparisons, and the claimed knowledge gap found no passage addressing that comparison. (LLM, conf=0.74)
- Not checked — no full text of the sourcecites [17] 17. Zhou, X.; Deng, J.; Fang, C.; Lei, W.; Song, Y.; Zhang, Z.; Huang, Z.; Li, Y. Additive manufacturing of CNTs/PLA composites and the correlation between microstructure and functional properties. Journal of Materials Science & Technology 2021, 60, 27-34. source
- Not checked — no full text of the sourcecites [21] 21. Jikei, M.; Takeyama, Y.; Yamadoi, Y.; Shinbo, N.; Matsumoto, K.; Motokawa, M.; Ishibashi, K.; Yamamoto, F. Synthesis and properties of Poly (L-lactide)-Poly (ɛ-caprolactone) multiblock copolymers by the self-polycondensation of diblock macromonomers. Polymer Journal 2015, 47 (10), 657-665. source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“When SC formation takes place, visible due to the peaks at 12° and 24°, the HC crystallization peak disappears (e.g. Figure 2B 50:50).”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > Materials Advances Accepted Manuscript
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The WAXS graphs exhibit a peak at 17.2° indicating partial crystallization of HC as α-phase (ordered α crystal).”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > DOI: 10.1039/D5MA00886G
hedgedstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
128 more claims
Create a free account to see all 284 claims and every source verdict.
- Probably not a substantial claim. 61
- It may state two separate claims as one. 106
- Borderline: one of the tests for a substantial claim is unclear. 1
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
“P(PCL 113b-PLLA 26 ) 24 blended with PDL 29 .In contrast, the MBC investigated by Jikei et al., consisting of PLLA 22 -b-PCL 49 mixed with PDLA 27 , demonstrated stereocomplex (SC) formation at a 1:1 molar ratio.25 Both systems exhibit a comparable PCL-to-PLLA block length ratio of approximately 2:1.”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > Materials Advances Accepted Manuscript
Reported 2 · recomputed 4.346154
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > Stereocomplex formation depends on PCL segment length
“Interestingly, no SC formation occurs in any of the blends”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > DOI: 10.1039/D5MA00886G
“P(PCL 113 -b-PLLA 26 ) 24: PDLA 56 , in which no diffraction peaks of PLA-HC are visible, but diffraction peaks of SC at 12.4, 20.8 and 24° can be observed for 90/10 mixture.”
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > Stereocomplex formation depends on PCL segment length
“no SC formation was observed in the combination of long PCL blocks with short PLA blocks l/s (Figure 2 C).”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > DOI: 10.1039/D5MA00886G
“in which no diffraction peaks of PLA-HC are visible, but diffraction peaks of SC at 12.4, 20.8 and 24° can be observed for 90/10 mixture.”
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
“In the present study, the long/short multiblock copolymer (l/s MBC) is composed of P(PCL 113b-PLLA 26 ) 24 blended with PDL 29 .In contrast, the MBC investigated by Jikei et al., consisting of PLLA 22 -b-PCL 49 mixed with PDLA 27 , demonstrated stereocomplex (SC) formation at a 1:1 molar ratio.25 Both systems exhibit a comparable PCL-to-PLLA block length ratio of approximately 2:1.”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > Materials Advances Accepted Manuscript
Reported 2 · recomputed 4.346154
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > Materials Advances Accepted Manuscript
“Crystallite sizes vary with the composition between 1-8 nm (SC), 1-20 nm (PCL) and 1-50 nm (HC)”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > DOI: 10.1039/D5MA00886G
“The SC crystallite size found in the P(PCL m -b-PLLA n ) x :PDLA 56 blends were between 5 and 13 nm.The largest SC crystallites of ~13 nm in this series were found in the s/l P(PCL 66 -b-PLLA 32 ) 43 and l/l P(PCL 121 -b-PLLA 49 ) 26 MBCs”
6 more findings
Create a free account to see every finding of this check.
Citations
Cites
The Scherrer equation versus the 'Debye-Scherrer equation'
Holzwarth, U., & Gibson, N. (2011) · Nature Nanotechnology · doi:10.1038/nnano.2011.145 · Cited by 3,407
Stereocomplex formation between enantiomeric poly(lactides)
Ikada, Y., Jamshidi, K., Tsuji, H., & Hyon, S. H. (1987) · Macromolecules · doi:10.1021/ma00170a034 · Cited by 1,409
Poly(lactide) Stereocomplexes: Formation, Structure, Properties, Degradation, and Applications
Tsuji, H. (2005) · Macromolecular Bioscience · doi:10.1002/mabi.200500062 · Cited by 1,366
A note on single crystals in polymers: Evidence for a folded chain configuration
Keller, A. (1957) · Philosophical Magazine · doi:10.1080/14786435708242746 · Cited by 1,019
Crescenzi, V., Manzini, G., Calzolari, G., & Borri, C. (1972) · European Polymer Journal · doi:10.1016/0014-3057(72)90109-7 · Cited by 750
Precise calculation of crystallite size of nanomaterials: A review
Hassanzadeh-Tabrizi, S. A. (2023) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2023.171914 · Cited by 649
Aliphatic Polyester Block Polymers: Renewable, Degradable, and Sustainable
Hillmyer, M. A., & Tolman, W. B. (2014) · Accounts of Chemical Research · doi:10.1021/ar500121d · Cited by 635
Relaxation processes in crystalline polymers: experimental behaviour — a review
Boyd, R. H. (1985) · Polymer · doi:10.1016/0032-3861(85)90192-2 · Cited by 624
Mechanism of the Stereocomplex Formation between Enantiomeric Poly(lactide)s
Brizzolara, D., Cantow, H.-J., Diederichs, K., Keller, E., & Domb, A. J. (1996) · Macromolecules · doi:10.1021/ma951144e · Cited by 547
Tsuji, H., & Ikada, Y. (1999) · Polymer · doi:10.1016/s0032-3861(99)00004-x · Cited by 545
Cited by
Baer, A. L., Clarke, R. W., Gowda, R. R., Hesse, S. A., Crowley, M., Xu, S., Hamernik, L. J., Curley, J. B., Urgun-Demirtas, M., Tassone, C. J., et al. (2026) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.6c00712 · Cited by 2
Lu, H., Gong, L., Cao, B., & Bao, J. (2026) · Journal of Polymer Science · doi:10.1002/pola.70111
Improving interlayer adhesion of 3D printed PLA/PCL blends using triblock copolymers
Rachmani, O., Zaltsman, I., Otorgust, G., Mizrahi, L., Ophir, A., Kol, M., & Amir, E. (2026) · Progress in Additive Manufacturing · doi:10.1007/s40964-026-01643-6 · Cited by 1
Nifant'ev, I. E., & Ivchenko, P. V. (2026) · European Polymer Journal · doi:10.1016/j.eurpolymj.2026.114863
Hu, M., Kong, X., & Qian, J. (2026) · Acta Mechanica Sinica · doi:10.1007/s10409-025-25925-x
Metadata
- Authors
- Mandlule, A., Liu, Y., Schwanz, S., Pieper, Y., Scharf, H., Iskhakova, K., Conceição, A. L. C., Wieland, D. C. F., Zeller-Plumhoff, B., Toma, F. M., & Neffe, A. T.
- Affiliations
- Helmholtz-Zentrum Hereon (DE)
- Karlsruhe Institute of Technology (DE)
- Deutsches Elektronen-Synchrotron DESY (DE)
- Helmholtz-Zentrum Hereon, Institute of Metallic Biomaterials, Max-Planck-Str. 1, 21502 Geesthacht, Germany
- Helmut Schmidt University (DE)
- ORCID
- Venue
- Materials Advances
- Publisher
- Royal Society of Chemistry (RSC)
- Published
- 2026
- Volume
- 7
- Issue
- 1
- Pages
- 377-402
- ISSN
- 2633-5409 (ISSN-L)
- OpenAlex
- W4416392925
- Cited by
- 6
- References
- 94
- Citations by year
- 2026: 6
- FWCI
- 1.25
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Materials Advances (publishedVersion, cc-by)
- Funders
- Helmholtz-Gemeinschaft (Joint Lab “Model and Data Driven Materials Characterization)
- Deutsches Elektronen-Synchrotron (Beamline proposal 20231350)
- Topics
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
- Physical Sciences › Materials Science › Materials Chemistry › Block Copolymer Self-Assembly
- Keywords
- stereocomplex formation, polycaprolactone, poly(L-lactic acid), multiblock copolymers, polylactic acid, polymer blends
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-09-28, under version 3 of the claim definition (prompt extract-v3).
A second model labelled each claim on 2026-09-28 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m - b -PLLA n ) multiblock-copolymers and PDLA. https://app.cochat.ai/papers/10.1039/d5ma00886g
- The paper
- Mandlule, A., Liu, Y., Schwanz, S., Pieper, Y., Scharf, H., Iskhakova, K., Conceição, A. L. C., Wieland, D. C. F., Zeller-Plumhoff, B., Toma, F. M., & Neffe, A. T. (2026). Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m - b -PLLA n ) multiblock-copolymers and PDLA. Materials Advances. https://doi.org/10.1039/d5ma00886g
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.