The DOI matches its Crossref record; 147 of the 151 references it cites were found in a registry or an index; 5 of the 201 sources its claims cite were checked for support.
Cellulosic Bionanocomposites: A Review of Preparation, Properties and Applications
Open accessAbstract
Cellulose is the most abundant biomass material in nature. Extracted from natural fibers, its hierarchical and multi-level organization allows different kinds of nanoscaled cellulosic fillers—called cellulose nanocrystals or microfibrillated cellulose (MFC)—to be obtained. Recently, such cellulose nanoparticles have been the focus of an exponentially increasing number of works or reviews devoted to understanding such materials and their applications. Major studies over the last decades have shown that cellulose nanoparticles could be used as fillers to improve mechanical and barrier properties of biocomposites. Their use for industrial packaging is being investigated, with continuous studies to find innovative solutions for efficient and sustainable systems. Processing is more and more important and different systems are detailed in this paper depending on the polymer solubility, i.e., (i) hydrosoluble systems, (ii) non-hydrosoluble systems, and (iii) emulsion systems. This paper intends to give a clear overview of cellulose nanoparticles reinforced composites with more than 150 references by describing their preparation, characterization, properties and applications.
Overview
CoChat Summary
TL;DR
This review summarizes preparation, properties, and applications of cellulosic bionanocomposites reinforced with cellulose nanocrystals/whiskers and microfibrillated cellulose (MFC). It reports that these nanofillers can strongly improve mechanical and barrier properties, often via a percolating hydrogen-bonded network, while processing and industrial scale-up remain challenging.
Key findings
- Cellulose nanoparticles act as effective reinforcing fillers; the strong effect is generally attributed to formation of a percolating network above the percolation threshold from hydrogen bonding between nanoparticles.
- Mechanical examples include poly(S-co-BuA) latex with 30 wt% wheat straw cellulose whiskers showing a rubbery Young’s modulus more than 1000-times higher than the bulk matrix; 10 wt% cellulose palm tree whiskers in natural rubber decreased strain at break from 575% to 16%; 5 wt% MFC improved PU modulus by approximately 200% at 5 °C and close to 500% at 85 °C; and PLA-MFC modulus increased from 5 GPa at 10 wt% MFC to almost 9 GPa at 70 wt% MFC.
- Barrier properties can improve: pure MFC films had oxygen transmission rate values of 17.0 and 17.8 mL m⁻² day⁻¹; MFC coating on PLA decreased OTR from 746 to 1 mL m⁻² day⁻¹ Pa⁻¹; and 10 wt% sulfonated whiskers in xylan/sorbitol films decreased WVTR from 304 to 174 g h⁻¹ m⁻².
- Thermal behavior varies: several studies found no important Tg changes with cellulose nanofillers, while moisture, plasticization, and filler content can alter Tg and crystallinity depending on the system.
Methods
- Narrative review of cellulose nanoparticles (whiskers/nanocrystals and MFC), their preparation, characterization, properties, and applications, citing more than 150 references.
- Describes processing routes classified by polymer solubility: hydrosoluble systems, emulsion systems, and non-hydrosoluble systems, plus solvent casting, extrusion, surfactant coating, and surface chemical modification/grafting.
- No new experimental data are generated; the paper synthesizes selected published works and cites SciFinder literature trends, e.g., papers on “cellulose and nano” increased from 57 in 2000 to more than 700 in 2009.
Limitations
- The paper states that toxicity is not discussed because of “a lot of uncertainty,” that practical transition from laboratory to industrial scale is not simple and requires chemical engineering to reduce nanoparticle production costs, and that inconsistent terminology for cellulose nanoparticles causes misunderstanding and ambiguity.
- Evident from the text: as a narrative review, it summarizes “some selected works” rather than using a described systematic search or inclusion criteria, and it does not perform quantitative meta-analysis.
- Evident from the text: many property claims are drawn from cited studies rather than independently verified here, and the review notes limited reported use of cellulose nanocrystals for barrier properties and possible porosity in nanocomposite films reducing MFC efficiency.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
5 Valid · 6 Not valid · 149 Not checked · 42 Own results and interpretations
In the paper
“Several authors did not observed important changes in the Tg of nanocomposites reinforced with cellulose nanofillers. This result was surprising due to the high specific area of such nanofillers, e.g., around 170 m 2 g -1 for tunicin whiskers [139].”
- Also stated in: § 3.2. Thermal Properties · plain
“Several authors did not observed important changes in the Tg of nanocomposites reinforced with cellulose nanofillers.”
What the sources say
- Not checked — no full text of the sourcecites [139] Angles, 2000, Plasticized starch/tunicin whiskers nanocomposites. 1. Structural analysis, Macromolecules source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § 3.2. Thermal Properties · plain
In the paper
“However, it seems that, at least under the conditions presented in this work, the cellulose chemical modification via grafting-from technique changes partially the cellulose crystallinity.”
What the sources say
- Not checked — no full text of the sourcecites [44] Morandi, 2009, Cellulose nanocrystals grafted with polystyrene chains through surface-initiated atom transfer radical polymerization (SI-ATRP), Langmuir source
hedgedstates a possible causeSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
In the paper
“Indeed, classical predicting models for short-fiber composites cannot be applied.”
What the sources say
- Not checked — no full text of the sourcecites [71] Favier, 1995, Polymer nanocomposites reinforced by cellulose whiskers, Macromolecules source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A claim is checked only against the cited paper’s full text, never its abstract, and none is available for its sources.
In the paper
“The DMA experiments demonstrated that the storage modulus of PU-MFC nanocomposites was improved over the whole temperature range compared to pure PU [136,137].”
What the sources say
- Not checked — no full text of the sourcecites [136] Seydibeyoglu, 2008, Novel nanocomposites based on polyurethane and micro fibrillated cellulose, Compos. Sci. Technol. source
- Not checked — no full text of the sourcecites [137] Wu, 2007, A high strength nanocomposite based on microcrystalline cellulose and polyurethane, Biomacromolecules source
boostedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
In the paper
“High efficiency was reached by this method that allowed esterification of cellulose nanoparticles to different extents with fatty acid chlorides.”
What the sources say
- Not checked — no full text of the sourcecites [129] Berlioz, 2009, Gas-phase surface esterification of cellulose microfibrils and whiskers, Biomacromolecules source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
108 more claims
Create a free account to see all 202 claims and to verify the 1 reference still open.
- Probably not a substantial claim. 61
- It may state two separate claims as one. 45
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Cellulosic Bionanocomposites: A Review of Preparation, Properties and Applications
“This paper intends to give a clear overview of cellulose nanoparticles reinforced composites with more than 150 references by describing their preparation, characterization, properties and applications.”
§ References
“150. Saxena, A.; Ragauskas, A.J. Water transmission barrier properties of biodegradable films based on cellulosic whiskers and xylan. Carbohyd. Polym. 2009 , 78 , 357-360.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ References
“23. Lu, J.; Askeland, P.; Drzal, L.T. Surface modification of microfibrillated cellulose for epoxy composite applications. Polymer 2008 , 49 , 1285-1296.”
§ References
“35. Lu, J.; Askeland, P.; Drzal, L.T. Surface modification of microfibrillated cellulose for epoxy composite applications. Polymer 2008 , 49 , 1285-1298.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 3.2. Thermal Properties
“However, when bacterial cellulose nanocrystals were modified with silane groups, Tm values were founded to increase with increasing filler content. According to the authors, this difference was due to stronger interactions between silylated whiskers and PVA matrix.”
§ 3.2. Thermal Properties
“Grunert et al. [43] in their work with cellulose acetate butyrate (CAB) reinforced with bacterial cellulose nanocrystals.”
Citations
Cites
Cellulose nanocrystals: chemistry, self-assembly, and applications
Habibi, Y., Lucia, L. A., & Rojas, O. J. (2010) · Chemical Reviews · doi:10.1021/cr900339w · Cited by 5,980 · cited 1×
“[61] gives a clear overview of such cellulosic nanomaterials.”
BackgroundComposites reinforced with cellulose based fibres
Bledzki, A. (1999) · Progress in Polymer Science · doi:10.1016/s0079-6700(98)00018-5 · Cited by 4,696 · cited 5×
“The term ―natural fibers‖ is used to designate numerous kinds of fibers that are naturally produced by plants, animals and minerals [5].”
BackgroundInfluentialNishiyama, Y., Langan, P., & Chanzy, H. (2002) · Journal of the American Chemical Society · doi:10.1021/ja0257319 · Cited by 3,028
Natural fibres: Can they replace glass in fibre reinforced plastics?
Wambua, P., Ivens, J., & Verpoest, I. (2003) · Composites Science and Technology · doi:10.1016/s0266-3538(03)00096-4 · Cited by 2,676 · cited 1×
“Indeed lignocellulosic materials start to degrade near 220 °C restricting the type of matrix that can be used in association with natural fillers [22,101].”
BackgroundCellulose nanofibers prepared by TEMPO-mediated oxidation of native cellulose
Saito, T., Kimura, S., Nishiyama, Y., & Isogai, A. (2007) · Biomacromolecules · doi:10.1021/bm0703970 · Cited by 2,493 · cited 2×
“In their study [86], individualized MFC was obtained by TEMPO-mediated oxidation at room temperature and stirring at 500 rpm.”
MethodJOHN, M., & THOMAS, S. (2008) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2007.05.040 · Cited by 2,453 · cited 1×
“their ability to form hydrogen bonds play a major role in directing the crystalline packing and also governing the physical properties of cellulose [16].”
BackgroundAzizi Samir, M. A. S., Alloin, F., & Dufresne, A. (2005) · Biomacromolecules · doi:10.1021/bm0493685 · Cited by 2,311
Self-citationPääkkö, M., Ankerfors, M., Kosonen, H., Nykänen, A., Ahola, S., Österberg, M., Ruokolainen, J., Laine, J., Larsson, P. T., Ikkala, O., et al. (2007) · Biomacromolecules · doi:10.1021/bm061215p · Cited by 1,962
Saito, T., Nishiyama, Y., Putaux, J.-L., Vignon, M., & Isogai, A. (2006) · Biomacromolecules · doi:10.1021/bm060154s · Cited by 1,796 · cited 1×
“[85,86] have proposed a new process to obtain MFC based on TEMPO reaction and strong mixing.”
MethodNatural Fibers, Biopolymers, and Biocomposites
(2005) · CRC Press eBooks · doi:10.1201/9780203508206 · Cited by 1,617
Research works printed but not linked: 9
- Gandini, A., and Belgacem, M.N. (2008). Monomers, Polymers and Composites from Renewable Resources, Elsevier. [1st ed.].
- Nalwa, H.S. Encyclopedia of Nanoscience and Nanotechnology, American Scientific Publisher. [2nd ed.]. in press.
- Brännvall, E. (2007). Aspect on Strength Delivery and Higher Utilisation of Strength Potential of Soft Wood Kraft Pupl Fibres. [Ph.D. Thesis, KTH, Royal Institute of Technology].
- Kroschwitz, 2003, Cellulose, Encyclopedia of Polymler Science and Technology, Volume 5, 473
- Lu, 2008, Surface modification of microfibrillated cellulose for epoxy composite applications, Polymer, 49, 1285, 10.1016/j.polymer.2008.01.028 · DOI · Paper page
- Herrick, 1983, Microfibrillated cellulose: Morphology and accessibility, J. Appl. Polym. Sci. Appl. Polym. Symp., 37, 797
- Khademhosseini, 2006, Nanobiotechnology—Drug delivery and tissue engineering, Chem. Engin. Progress, 102, 38
- Gandini, A., and Belgacem, M.N. (2008). Monomers, Polymers and Composites from Renewable Resources, Elsevier. [1st ed.].
- Gandini, A., and Belgacem, M.N. (2008). Monomers, Polymers and Composites from Renewable Resources, Elsevier. [1st ed.].
Cited by
Cellulose nanomaterials review: structure, properties and nanocomposites
Moon, R. J., Martini, A., Nairn, J., Simonsen, J., & Youngblood, J. (2011) · Chemical Society Reviews · doi:10.1039/c0cs00108b · Cited by 6,756
Lavoine, N., Desloges, I., Dufresne, A., & Bras, J. (2012) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2012.05.026 · Cited by 1,791
Self-citationProduction of nanocrystalline cellulose from lignocellulosic biomass: Technology and applications
Brinchi, L., Cotana, F., Fortunati, E., & Kenny, J. M. (2013) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2013.01.033 · Cited by 1,121
Biobased plastics and bionanocomposites: Current status and future opportunities
Reddy, M. M., Vivekanandhan, S., Misra, M., Bhatia, S. K., & Mohanty, A. K. (2013) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2013.05.006 · Cited by 1,080
Recent progress in cellulose nanocrystals: sources and production
Trache, D., Hussin, M. H., Haafiz, M. K. M., & Thakur, V. K. (2017) · Nanoscale · doi:10.1039/c6nr09494e · Cited by 1,064
Metadata
- Authors
- Siqueira, G., Bras, J., & Dufresne, A.
- Affiliations
- Institut polytechnique de Grenoble (FR)
- Corresponding author
- Dufresne, Alain
- Venue
- Polymers
- Publisher
- MDPI AG
- Published
- 2010-12-13
- Volume
- 2
- Issue
- 4
- Pages
- 728-765
- ISSN
- 2073-4360 (ISSN-L)
- OpenAlex
- W1980921765
- Semantic Scholar
- 88e39e80ebe121f79b7f4d6157891419553dc112
- Cited by
- 1,328
- References
- 151
- Citations by year
- 2026: 44 · 2025: 59 · 2024: 69 · 2023: 89 · 2022: 91 · 2021: 111 · 2020: 83 · 2019: 111 · 2018: 101 · 2017: 118 · 2016: 102 · 2015: 113 · 2014: 117 · 2013: 59 · 2012: 41
- FWCI
- 15.68
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Polymers (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Topics
- Physical Sciences › Materials Science › Biomaterials › Advanced Cellulose Research Studies
- Physical Sciences › Materials Science › Biomaterials › Nanocomposite Films for Food Packaging
- Physical Sciences › Materials Science › Polymers and Plastics › Natural Fiber Reinforced Composites
- Keywords
- cellulose nanocrystals, microfibrillated cellulose, cellulose nanoparticles, biocomposites, mechanical properties, barrier properties, packaging materials, emulsion processing, natural fibers
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-07, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-07 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Cellulosic Bionanocomposites: A Review of Preparation, Properties and Applications. https://app.cochat.ai/papers/10.3390/polym2040728
- The paper
- Siqueira, G., Bras, J., & Dufresne, A. (2010). Cellulosic Bionanocomposites: A Review of Preparation, Properties and Applications. Polymers. https://doi.org/10.3390/polym2040728
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.