The DOI matches its Crossref record; 281 of the 281 references it cites were found in a registry or an index; 44 of the 222 sources its claims cite were checked for support.
Recent Advances on PEM Fuel Cells: From Key Materials to Membrane Electrode Assembly
Open accessAbstract
This review critically covers recent progress of key materials for MEAs, focusing on how to integrate materials into electrodes and MEAs, along with advanced designs and manufacturing techniques.
Overview
CoChat Summary
TL;DR
This critical review surveys recent progress in key PEM fuel cell materials—catalysts, membranes/ionomers, and gas diffusion layers—and state-of-the-art membrane electrode assembly (MEA) manufacturing. It argues that despite advances, cost and lifetime barriers remain, especially low-Pt-loading performance loss, PGM-free catalyst instability, and gaps between rotating-disk-electrode (RDE) activity and MEA performance.
Key findings
- Pt-based catalysts remain the benchmark: the first-generation Toyota Mirai had total Pt loading of 0.365 mg Pt cm⁻² versus 35 mg Pt cm⁻² for a 1962 practical fuel cell, and the second-generation Mirai stack reached 5.4 kW L⁻¹ versus 3.1 kW L⁻¹ for the first generation; Mirai anode/cathode loadings were 0.05 and 0.315 mg Pt cm⁻², respectively.
- Advanced Pt catalysts show high RDE activity: jagged Pt nanowires reached ECSA up to 118 m² g⁻¹ and mass activity of 13.6 A mg Pt⁻¹ at 0.9 V; sulfur-anchored intermetallics were controlled to <5 nm after up to 1 000 °C sintering and reached 1.3–1.8 A mg Pt⁻¹ at 0.9 V; Fe-N-C catalysts achieved a half-wave potential of (0.88 ± 0.01) V vs. RHE, but PGM-free catalysts remain less active and stable than Pt in acidic PEM fuel cells.
- MEA manufacturing advances include CCM over CCS, slot-die and roll-to-roll coating, and freeze-drying to increase catalyst-layer porosity; a moderate ionomer content of ~26 wt.% gave the highest electrokinetic performance, and decal transfer cost was estimated at ~1.67 times the electrode coating process at 500 000 units/year.
- Material and operational constraints persist: PFSA membranes may be <10 µm thick but suffer higher gas crossover; PA-doped PBI membranes can operate from −20 to 200 °C; a protonated phosphonic acid PEM fuel cell delivered 780 mW cm⁻² at 160 °C with minimal degradation over 2 500 h and 700 thermal cycles; GDL thickness is typically 200–400 µm, and DOE heavy-duty targets are 25 000 and 30 000 h for 2025 and 2030.
Methods
- Design: critical review, not a primary experimental study; it focuses on “mature materials” used in industrial production and on integrating materials into electrodes and MEAs.
- Data/sample: literature and prior studies on ORR catalysts, membranes/ionomers, GDLs, and MEA fabrication steps; no new experimental sample or dataset is reported.
- Analysis: narrative synthesis organized by material class and manufacturing step, with tables of physical/electrochemical characterization methods for screening catalysts, membranes, ionomers, and GDLs, plus discussion of constraints and advanced integration strategies.
Limitations
- Stated: decreasing Pt loading causes performance loss and the low-Pt barrier is not completely addressed; PGM-free catalysts such as Fe-N-C degrade severely and remain far behind Pt; PFSA membranes have a restricted operating window and hydrocarbon ionomers are not mature for scale-up; optimal GDL porosity and pore-size distribution are not widely agreed; catalyst ink stability and high-efficiency, low-cost dispersion remain challenging; ordered catalyst layers may be difficult to scale up; and roll-to-roll coating faces multiple precision, lamination, and defect-control challenges.
- Evident from the text: as a review, it provides no primary experimental validation and relies on cited literature; it also repeatedly notes that RDE activity often cannot be reproduced in MEA testing, so reported catalyst performance may not translate directly to practical MEAs.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
40 Valid · 13 Not valid · 138 Not checked · 98 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“In addition to the significant progress in Pt-based catalysts for ORR, a large number of efforts have been devoted to Pt-group-metal-free (PGM-free) catalysts, which are promising alternatives to replace costly and scarce Pt catalysts [44,45].”
§ Recent Advances on PEM Fuel Cells: From Key Materials to Membrane Electrode Assembly > 2.1 Catalysts
What the sources say
- Partly supportedcites [44] Du, L., Zhang, G.X., Sun, S.H.: Proton exchange membrane (PEM) fuel cells with platinum group metal (PGM)-free cathode. Automot. Innov. 4, 131–143 (2021). https://doi.org/10.1007/s42154-021-00146-0 sourceExperimental — accuracy not yet measured
The Introduction says Pt-based PGM catalysts raise fuel-cell costs and calls replacing cathode PGMs with PGM-free alternatives a promising strategy. The section on high-performance PGM-free catalysts also describes them as a promising replacement. Our copy does not establish the claim that Pt is scarce. (LLM, conf=0.84)
- Not checked — no full text of the sourcecites [45] Du, L., Xing, L.X., Zhang, G.X., et al.: Strategies for engineering high-performance PGM-free catalysts toward oxygen reduction and evolution reactions. Small Methods 4, 2000016 (2020). https://doi.org/10.1002/smtd.202000016 source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“Over the past decades, several kinds of PGM-free catalysts have been developed, among which the most representative is Fe-N-C due to its superior activity as a site for ORR [47].”
§ Recent Advances on PEM Fuel Cells: From Key Materials to Membrane Electrode Assembly > 2.1 Catalysts
What the sources say
- Supportedcites [47] Du, L., Zhang, G.X., Liu, X.H., et al.: Biomass-derived nonprecious metal catalysts for oxygen reduction reaction: the demand-oriented engineering of active sites and structures. Carbon Energy 2, 561–581 (2020). https://doi.org/10.1002/cey2.73 source
Section 3 identifies single-atom Fe-N-C as a representative, promising PGM-free ORR catalyst. Section 3.2 describes its FeNₓ moieties as among the most promising PGM-free active sites for ORR. The source does not claim Fe-N-C outperforms PGM-based catalysts, but the citing sentence does not make that comparison. (LLM, conf=0.88)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“As shown in Fig. 3a, b, a reliable ensemble learner, XGBoost, was established and trained to rank the degrees of importance among 26 complicated features in PEM fuel cells.”
§ Recent Advances on PEM Fuel Cells: From Key Materials to Membrane Electrode Assembly > 2.1 Catalysts
What the sources say
- Supportedcites [57] Ding, R., Wang, R., Ding, Y.Q., et al.: Designing AI-aided analysis and prediction models for nonprecious metal electrocatalyst-based proton-exchange membrane fuel cells. Angew. Chem. Int. Ed. 59, 19175–19183 (2020). https://doi.org/10.1002/anie.202006928 source
The Conclusion (p. of our copy) states almost verbatim that 'a reliable ensemble learner, XGBoost, ranked the degrees of importance among 26 complicated features', and the Methods section (Machine Learning Algorithms Applied as Computational Tools) confirms XGBoost was chosen 'to provide a fair assessment of the importance among the 26 features'. The Feature Importance Ranking section reports the F-score-based ranking shown in Figure 3 and describes XGBoost as 'a reliable learner' (91.4% weighted precision), matching the citing sentence's Fig. 3a,b reference. The PEMFC/NPME context is the paper's own subject throughout. (LLM, conf=0.94)
boostedstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“to therefore present better performance in MEA, particularly at low humidity (Fig. 5c).”
§ Recent Advances on PEM Fuel Cells: From Key Materials to Membrane Electrode Assembly > 2.2 Membranes and Ionomers
What the sources say
- Partly supportedcites [78] Li, T., Shen, J.B., Chen, G.Y., et al.: Performance comparison of proton exchange membrane fuel cells with Nafion and aquivion perfluorosulfonic acids with different equivalent weights as the electrode binders. ACS Omega 5, 17628–17636 (2020). https://doi.org/10.1021/acsomega.0c02110 sourceExperimental — accuracy not yet measured
The Results and Discussion section (Static Performance Response to Operation Conditions; page not provided) reports better performance for Aquivion-based SSC-CCMs than Nafion-based LSC-CCMs, with the difference greatest at low humidity. But the Experimental Section (Preparation of CCM; page not provided) says both were made by spraying different electrode-binder ionomers onto the same Gore membrane. The study therefore does not establish that an Aquivion membrane outperforms a Nafion membrane in an MEA. (LLM, conf=0.90)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Recently, dual single-atom catalysts were proposed to achieve better ORR intrinsic activity, e.g., Fe/ Co-N-C [53,54].”
§ Recent Advances on PEM Fuel Cells: From Key Materials to Membrane Electrode Assembly > 2.1 Catalysts
What the sources say
- Partly supportedcites [53] Gollasch, M., Müller-Hülstede, J., Schmies, H., et al.: Elucidating synergistic effects of different metal ratios in bimetallic Fe/Co–N–C catalysts for oxygen reduction reaction. Catalysts 11, 841 (2021). https://doi.org/10.3390/catal11070841 sourceExperimental — accuracy not yet measured
Our copy does support the concept the citing sentence attaches to this source: the Introduction (Sec. 1) frames bimetallic Fe/Co-N-C with atomically dispersed Me-N sites as a route to 'tackle the downsides of each individual metal' (Fe's high ORR activity plus Co's stability), and the Conclusions (Sec. 4) confirm 'Proposed atomically dispersed Me-N sites have been achieved'. However, the source does not use the term 'dual single-atom catalysts', and its own data do not show an intrinsic-activity gain: Sec. 2.2.1/Table 1 reports that all bimetallic catalysts have higher Tafel slopes (72-83 mV dec-1) than the monometallic ones (57-63), 'hence the higher kinetic activity' being lower, and the Conclusions state monometallic Fe-N-C shows the highest ORR activity. So the 'proposed to achieve better ORR intrinsic activity' part is only supported as a stated hypothesis/motivation, not as a finding of this work. (LLM, conf=0.72)
- Not checked — no full text of the sourcecites [54] Han, Y., Yin, S.H., Chen, Y.H., et al.: Experimental and DFT studies of oxygen reduction reaction promoted by binary site Fe/Co–N–C catalyst in acid. J. Electroanal. Chem. 914, 116322 (2022). https://doi.org/10.1016/j.jelechem.2022.116322 source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
144 more claims · 27 with their cited sources checked
Create a free account to see all 289 claims and to verify the 15 references still open.
- It may state two separate claims as one. 103
- Probably not a substantial claim. 49
- Borderline: one of the tests for a substantial claim is unclear. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Recent Advances on PEM Fuel Cells: From Key Materials to Membrane Electrode Assembly > 3 State-of-the-Art Membrane Electrode Assembly Manufacturing Processes
“The MEA fabrication process generally includes ink dispersing, electrode coating, electrode drying, slitting and cutting, component assembly, and pressing (Fig. 12a-f).”
§ Recent Advances on PEM Fuel Cells: From Key Materials to Membrane Electrode Assembly > Materials integration into the MEAs.
“Figure: 12 Fig. 12 a Fig.12a-e General MEA fabrication process, including ink dispersing, coating, drying, cutting, assembly, and pressing”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Recent Advances on PEM Fuel Cells: From Key Materials to Membrane Electrode Assembly > 3.2.2 Assembly Step
“The role of the GDL is discussed in Sect.2.4.”
§ Recent Advances on PEM Fuel Cells: From Key Materials to Membrane Electrode Assembly > 2.3 Gas Diffusion Layer (GDL)
“## 2.3 Gas Diffusion Layer (GDL)”
Citations
Cites
Single-atom catalysis of CO oxidation using Pt1/FeOx
Qiao, B., Wang, A., Yang, X., Allard, L. F., Jiang, Z., Cui, Y., Liu, J., Li, J., & Zhang, T. (2011) · Nature Chemistry · doi:10.1038/nchem.1095 · Cited by 7,526 · cited 1×
“Among various PGM-free catalysts, composites involving so-called single-atom moieties are emerging [46], i.e., transition metal–nitrogen–carbon (M–”
Electrocatalyst approaches and challenges for automotive fuel cells
Debe, M. K. (2012) · Nature · doi:10.1038/nature11115 · Cited by 5,885 · cited 2×
“This indicates less than one faulty MEA in 30 000 products [230].”
Computational high-throughput screening of electrocatalytic materials for hydrogen evolution
Greeley, J., Jaramillo, T. F., Bonde, J., Chorkendorff, I., & Nørskov, J. K. (2006) · Nature Materials · doi:10.1038/nmat1752 · Cited by 4,097 · cited 1×
“A high d-band center benefits the adsorption of oxygen-containing species but leads to slow intermediate desorption and active site poisoning, while a low d-band center suffers from slow adsorption of oxygen and low kinetics [37, 38].”
Why gold is the noblest of all the metals
Hammer, B., & Norskov, J. K. (1995) · Nature · doi:10.1038/376238a0 · Cited by 3,935 · cited 1×
“The d-band center of Pt sites has been widely accepted as a descriptor for ORR intrinsic activity [35–37].”
Batteries and fuel cells for emerging electric vehicle markets
Cano, Z. P., Banham, D., Ye, S., Hintennach, A., Lu, J., Fowler, M., & Chen, Z. (2018) · Nature Energy · doi:10.1038/s41560-018-0108-1 · Cited by 2,873 · cited 1×
“While PEM fuel cells have risen and declined in recent centuries, they presently play a key role in building a sustainable society [1].”
Self-citationFrom the Sabatier principle to a predictive theory of transition-metal heterogeneous catalysis
Medford, A. J., Vojvodic, A., Hummelshøj, J. S., Voss, J., Abild-Pedersen, F., Studt, F., Bligaard, T., Nilsson, A., & Nørskov, J. K. (2015) · Journal of Catalysis · doi:10.1016/j.jcat.2014.12.033 · Cited by 2,254
Stamenkovic, V., Mun, B. S., Mayrhofer, K. J. J., Ross, P. N., Markovic, N. M., Rossmeisl, J., Greeley, J., & Nørskov, J. K. (2006) · Angewandte Chemie International Edition · doi:10.1002/anie.200504386 · Cited by 2,109 · cited 1×
“A high d-band center benefits the adsorption of oxygen-containing species but leads to slow intermediate desorption and active site poisoning, while a low d-band center suffers from slow adsorption of oxygen and low kinetics [37, 38].”
Wang, D., Xin, H. L., Hovden, R., Wang, H., Yu, Y., Muller, D. A., DiSalvo, F. J., & Abruña, H. D. (2013) · Nature Materials · doi:10.1038/nmat3458 · Cited by 2,082
Review and analysis of PEM fuel cell design and manufacturing
Mehta, V., & Cooper, J. S. (2003) · Journal of Power Sources · doi:10.1016/s0378-7753(02)00542-6 · Cited by 1,685 · cited 1×
“16c) [194–200].”
Biaxially strained PtPb/Pt core/shell nanoplate boosts oxygen reduction catalysis
Bu, L., Zhang, N., Guo, S., Zhang, X., Li, J., Yao, J., Wu, T., Lu, G., Ma, J.-Y., Su, D., et al. (2016) · Science · doi:10.1126/science.aah6133 · Cited by 1,642 · cited 1×
“To date, various strategies to improve the performance have been developed, such as alloying Pt with transition metals [23, 24], building the core–shell structure [25, 26], nanowires [27–29], nanoplates [30], and nanoframes [31, 32].”
Research works printed but not linked: 1
- Jie, N.: Investigation of the colloidal behaviour of carbon black and perfluorosulfonated ionomer in various solvents. Dissertation, Queen’s University (2016). http://hdl.handle.net/1974/14081.
Cited by
Oxygen- and proton-transporting open framework ionomer for medium-temperature fuel cells
Yang, J., Xu, H., Li, J., Gong, K., Yue, F., Han, X., Wu, K., Shao, P., Fu, Q., Zhu, Y., et al. (2024) · Science · doi:10.1126/science.adq2259 · Cited by 237
Bin, S., Chen, Z., Zhu, Y., Zhang, Y., Xia, Y., Gong, S., Zhang, F., Shi, L., Duan, X., & Sun, Z. (2024) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2024.04.188 · Cited by 125
Zhao, C., Ding, Z., Zhang, K., Du, Z., Fang, H., Chen, L., Jiang, H., Wang, M., & Wu, M. (2025) · Nano-Micro Letters · doi:10.1007/s40820-025-01653-z · Cited by 132
“In contrast, the proton exchange membrane (PEM) elec-trolyzers [136, 137], which conduct protons, are more vulnerable to corrosion in chloride-rich environments due to potential Cl − infiltration that compromises membrane integrity [138].”
Celadon, A., Sun, H., Sun, S., & Zhang, G. (2024) · SusMat · doi:10.1002/sus2.234 · Cited by 122
“187 The penultimate challenge highlights the potential for recycling batteries to foster a new local economy, benefiting states through increased tax revenues, providing jobs for workers, and reducing transportation costs for materials.”
Lei, H., Yang, X., Chen, Z., Rawach, D., Du, L., Liang, Z., Li, D., Zhang, G., Tavares, A. C., & Sun, S. (2025) · Advanced Materials · doi:10.1002/adma.202410106 · Cited by 120
Self-citation
Metadata
- Authors
- Mo, S., Du, L., Huang, Z., Chen, J., Zhou, Y., Wu, P., Meng, L., Wang, N., Xing, L., Zhao, M., Yang, Y., Tang, J., Zou, Y., & Ye, S.
- Affiliations
- Guangzhou University (CN)
- Corresponding author
- Xing, Lixin
- Ye, Siyu
- Venue
- Electrochemical Energy Reviews
- Published
- 2023-08-17
- Volume
- 6
- Issue
- 1
- ISSN
- 2520-8136 (ISSN-L)
- 2520-8489
- OpenAlex
- W4385950481
- Semantic Scholar
- c0da1c409a6ea52ab5ae981dd027dfa5bbc1427c
- Cited by
- 277
- References
- 267
- Citations by year
- 2026: 82 · 2025: 119 · 2024: 75 · 2023: 1
- FWCI
- 20.53
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/4.0 (tdm)
- creativecommons.org/licenses/by/4.0 (vor)
- Locations
- Electrochemical Energy Reviews (publishedVersion, cc-by)
- Funders
- National Key Research and Development Program of China (2020YFB1505800)
- National Natural Science Foundation of China (22250710133, 51803042)
- Outstanding Youth Project of Natural Science Foundation of Guangdong Province (2022B1515020020)
- Funding by Science and Technology Projects in Guangzhou (202206050003, 202201010603)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Materials Science › Materials Chemistry › Advancements in Solid Oxide Fuel Cells
- Keywords
- proton exchange membrane fuel cells, membrane electrode assembly, fuel cell materials, fuel cell manufacturing, fuel cell lifetime, fuel cell cost, electrode materials, fuel cell vehicles
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol and qwen3.8-omni-flash).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Recent Advances on PEM Fuel Cells: From Key Materials to Membrane Electrode Assembly. https://app.cochat.ai/papers/10.1007/s41918-023-00190-w
- The paper
- Mo, S., Du, L., Huang, Z., Chen, J., Zhou, Y., Wu, P., Meng, L., Wang, N., Xing, L., Zhao, M., Yang, Y., Tang, J., Zou, Y., & Ye, S. (2023). Recent Advances on PEM Fuel Cells: From Key Materials to Membrane Electrode Assembly. Electrochemical Energy Reviews. https://doi.org/10.1007/s41918-023-00190-w
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.