The DOI matches its Crossref record; 65 of the 65 references it cites were found in a registry or an index.
Ultrahigh-strength titanium gyroid scaffolds manufactured by selective laser melting (SLM) for bone implant applications
Abstract
Abstract Commercially pure titanium (CP–Ti) gyroid scaffolds with interconnected pores and high porosities in the range of 68–73% and three different unit cell sizes of 2, 2.5, and 3 mm were manufactured by selective laser melting (SLM) for bone implant applications. The microstructure and mechanical properties of the scaffolds with different unit cell sizes and sample orientations were evaluated. The microstructure of as-built struts was dominated by massive martensite and the average microhardness of the struts was 2.27 GPa, which is ∼50% higher than that of dense cast CP–Ti. The elastic modulus and yield strength of the as-built scaffolds ranged from 1465 to 2676 MPa and from 44.9 to 56.5 MPa, respectively, values which are close to the elastic modulus of trabecular bone and presumably strong enough to bear the physiological loading of implants. The as-built scaffolds exhibited excellent ductility up to 50% strain and no sign of fracture up to 20–30% strain under compression. The dominant compressive response of the scaffolds was observed by formation of a plastic hinge which led to rotation of the struts about the plastic hinges followed by development of local shear bands in struts in the long plateau region. These SLM-manufactured gyroid CP–Ti scaffolds with significantly enhanced hardness and compressive strength exhibited an elastic modulus close to that of trabecular bone and offer a promising improvement on CP–Ti scaffolds for bone implant applications.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Cellular solids structure and properties
Gibson, L. J., Ashby, M. F., et al. (1997) · Cited by 9,172
Porosity of 3D biomaterial scaffolds and osteogenesis
Karageorgiou, V., & Kaplan, D. (2005) · Biomaterials · doi:10.1016/j.biomaterials.2005.02.002 · Cited by 6,622
A study of the microstructural evolution during selective laser melting of Ti–6Al–4V
Thijs, L., Verhaeghe, F., Craeghs, T., Humbeeck, J. V., & Kruth, J.-P. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.02.004 · Cited by 2,929
Ashby, M., Evans, A., Fleck, N., Gibson, L., Hutchinson, J., Wadley, H., & Delale, F. (2001) · Applied Mechanics Reviews · doi:10.1115/1.1421119 · Cited by 2,694
Wang, X., Xu, S., Zhou, S., Xu, W., Leary, M., Choong, P., Qian, M., Brandt, M., & Xie, Y. M. (2016) · Biomaterials · doi:10.1016/j.biomaterials.2016.01.012 · Cited by 2,121
Self-citationXu, W., Brandt, M., Sun, S., Elambasseril, J., Liu, Q., Latham, K., Xia, K., & Qian, M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2014.11.028 · Cited by 1,245
Self-citationGu, D., Hagedorn, Y.-C., Meiners, W., Meng, G., Batista, R. J. S., Wissenbach, K., & Poprawe, R. (2012) · Acta Materialia · doi:10.1016/j.actamat.2012.04.006 · Cited by 1,089
Formation and control of martensite in Ti-6Al-4V alloy produced by selective laser melting
Yang, J., Yu, H., Yin, J., Gao, M. X., Wang, Z., & Zeng, X. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.06.117 · Cited by 913
Bobbert, F. S. L., Lietaert, K., Eftekhari, A. A., Pouran, B., Ahmadi, S. M., Weinans, H., & Zadpoor, A. A. (2017) · Acta Biomaterialia · doi:10.1016/j.actbio.2017.02.024 · Cited by 873
Manufacture by selective laser melting and mechanical behavior of commercially pure titanium
Attar, H., Calin, M., Zhang, L. C., Scudino, S., & Eckert, J. (2014) · Materials Science and Engineering: A · doi:10.1016/j.msea.2013.11.038 · Cited by 744
Parry, L., Ashcroft, I. A., & Wildman, R. D. (2016) · Additive Manufacturing · doi:10.1016/j.addma.2016.05.014 · Cited by 739
Evaluations of cellular lattice structures manufactured using selective laser melting
Yan, C., Hao, L., Hussein, A., & Raymont, D. (2012) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2012.06.002 · Cited by 730
Yan, C., Hao, L., Hussein, A., & Young, P. (2015) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2015.06.024 · Cited by 717
Processing of biocompatible porous Ti and Mg
Wen, C. E., Mabuchi, M., Yamada, Y., Shimojima, K., Chino, Y., & Asahina, T. (2001) · Scripta Materialia · doi:10.1016/s1359-6462(01)01132-0 · Cited by 665
Self-citationMinimal surface scaffold designs for tissue engineering
Kapfer, S. C., Hyde, S. T., Mecke, K., Arns, C. H., & Schröder-Turk, G. E. (2011) · Biomaterials · doi:10.1016/j.biomaterials.2011.06.012 · Cited by 579
The effect of geometry on three-dimensional tissue growth
Rumpler, M., Woesz, A., Dunlop, J. W. C., van Dongen, J. T., & Fratzl, P. (2008) · Journal of The Royal Society Interface · doi:10.1098/rsif.2008.0064 · Cited by 531
Implant Surface Roughness and Bone Healing: a Systematic Review
Shalabi, M. M., Gortemaker, A., Hof, M. A. V., Jansen, J. A., & Creugers, N. H. J. (2006) · Journal of Dental Research · doi:10.1177/154405910608500603 · Cited by 531
Mathematically defined tissue engineering scaffold architectures prepared by stereolithography
Melchels, F. P. W., Bertoldi, K., Gabbrielli, R., Velders, A. H., Feijen, J., & Grijpma, D. W. (2010) · Biomaterials · doi:10.1016/j.biomaterials.2010.05.068 · Cited by 530
Bone tissue regeneration: the role of scaffold geometry
Zadpoor, A. A. (2015) · Biomaterials Science · doi:10.1039/c4bm00291a · Cited by 518
Ductility of a Ti‐6Al‐4V alloy produced by selective laser melting of prealloyed powders
Facchini, L., Magalini, E., Robotti, P., Molinari, A., Höges, S., & Wissenbach, K. (2010) · Rapid Prototyping Journal · doi:10.1108/13552541011083371 · Cited by 512
Van Bael, S., Kerckhofs, G., Moesen, M., Pyka, G., Schrooten, J., & Kruth, J. P. (2011) · Materials Science and Engineering: A · doi:10.1016/j.msea.2011.06.045 · Cited by 452
A poly(d,l-lactide) resin for the preparation of tissue engineering scaffolds by stereolithography
Melchels, F. P. W., Feijen, J., & Grijpma, D. W. (2009) · Biomaterials · doi:10.1016/j.biomaterials.2009.03.055 · Cited by 437
Is the energy density a reliable parameter for materials synthesis by selective laser melting?
Prashanth, K. G., Scudino, S., Maity, T., Das, J., & Eckert, J. (2017) · Materials Research Letters · doi:10.1080/21663831.2017.1299808 · Cited by 418
Mullen, L., Stamp, R. C., Brooks, W. K., Jones, E., & Sutcliffe, C. J. (2009) · Journal of Biomedical Materials Research Part B: Applied Biomaterials · doi:10.1002/jbm.b.31219 · Cited by 410
Silva, M. J., & Gibson, L. J. (1997) · International Journal of Mechanical Sciences · doi:10.1016/s0020-7403(96)00065-3 · Cited by 364
Yadroitsev, I., & Yadroitsava, I. (2015) · Virtual and Physical Prototyping · doi:10.1080/17452759.2015.1026045 · Cited by 349
Geometry as a Factor for Tissue Growth: Towards Shape Optimization of Tissue Engineering Scaffolds
Bidan, C. M., Kommareddy, K. P., Rumpler, M., Kollmannsberger, P., Fratzl, P., & Dunlop, J. W. C. (2013) · Advanced Healthcare Materials · doi:10.1002/adhm.201200159 · Cited by 341
Mazur, M., Leary, M., Sun, S., Vcelka, M., Shidid, D., & Brandt, M. (2015) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-015-7655-4 · Cited by 314
Self-citationSurface Modification of Ti6Al4V Open Porous Structures Produced by Additive Manufacturing
Pyka, G., Burakowski, A., Kerckhofs, G., Moesen, M., Van Bael, S., Schrooten, J., & Wevers, M. (2012) · Advanced Engineering Materials · doi:10.1002/adem.201100344 · Cited by 309
Porous scaffold design using the distance field and triply periodic minimal surface models
Yoo, D. J. (2011) · Biomaterials · doi:10.1016/j.biomaterials.2011.07.019 · Cited by 298
Kujala, S., Ryhänen, J., Danilov, A., & Tuukkanen, J. (2003) · Biomaterials · doi:10.1016/s0142-9612(03)00359-4 · Cited by 284
Cytotoxicity of Titanium and Titanium Alloying Elements
Li, Y., Wong, C. S., Xiong, J., Hodgson, P. D., & Wen, C. (2010) · Journal of Dental Research · doi:10.1177/0022034510363675 · Cited by 279
Self-citationComputer-aided porous scaffold design for tissue engineering using triply periodic minimal surfaces
Yoo, D.-J. (2011) · International Journal of Precision Engineering and Manufacturing · doi:10.1007/s12541-011-0008-9 · Cited by 271
Proceedings of the 13th World Conference on Titanium
Warchomicka, F., Zehetner, E., Poletti, C., et al. (2016) · Wiley eBooks · doi:10.1002/9781119296126 · Cited by 270
Properties of Ti–6Al–4V non-stochastic lattice structures fabricated via electron beam melting
Cansizoglu, O., Harrysson, O. L. A., Cormier, D., West, H., & Mahale, T. (2008) · Materials Science and Engineering A · doi:10.1016/j.msea.2008.04.002 · Cited by 267
Murr, L. E., Gaytan, S. M., Medina, F., Martinez, E., Martinez, J. L., Hernandez, D. H., Machado, B. I., Ramirez, D. A., & Wicker, R. B. (2010) · Materials Science and Engineering: A · doi:10.1016/j.msea.2009.11.015 · Cited by 258
Yánez, A., Cuadrado, A., Martel, O., Afonso, H., & Monopoli, D. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.11.050 · Cited by 252
Zheng, B., Zhou, Y., Smugeresky, J. E., Schoenung, J. M., & Lavernia, E. J. (2008) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-008-9557-7 · Cited by 245
Li, Y., & Gu, D. (2014) · Additive manufacturing · doi:10.1016/j.addma.2014.09.001 · Cited by 236
Self-citationBontha, S., Klingbeil, N. W., Kobryn, P. A., & Fraser, H. L. (2006) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2006.03.155 · Cited by 232
How Linear Tension Converts to Curvature: Geometric Control of Bone Tissue Growth
Bidan, C. M., Kommareddy, K. P., Rumpler, M., Kollmannsberger, P., Bréchet, Y. J. M., Fratzl, P., & Dunlop, J. W. C. (2012) · PLoS ONE · doi:10.1371/journal.pone.0036336 · Cited by 221
Massive transformation in Ti–6Al–4V additively manufactured by selective electron beam melting
Lu, S., Qian, M., Tang, H., Yan, M., Wang, J., & StJohn, D. H. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.11.011 · Cited by 218
Novel titanium foam for bone tissue engineering
Wen, C. E., Yamada, Y., Shimojima, K., Chino, Y., Hosokawa, H., & Mabuchi, M. (2002) · Journal of Materials Research · doi:10.1557/jmr.2002.0382 · Cited by 210
Self-citationA TPMS-based method for modeling porous scaffolds for bionic bone tissue engineering
Shi, J., Zhu, L., Li, L., Li, Z., Yang, J., & Wang, X. (2018) · Scientific Reports · doi:10.1038/s41598-018-25750-9 · Cited by 207
Biomimetics Learning from Nature
(2010) · InTech eBooks · doi:10.5772/198 · Cited by 197
Development and mechanical characterization of porous titanium bone substitutes
Barbas, A., Bonnet, A.-S., Lipinski, P., Pesci, R., & Dubois, G. (2012) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2012.01.008 · Cited by 180
Yoo, D.-J. (2014) · International Journal of Precision Engineering and Manufacturing · doi:10.1007/s12541-014-0516-5 · Cited by 175
Revival of pure titanium for dynamically loaded porous implants using additive manufacturing
Wauthle, R., Ahmadi, S. M., Amin Yavari, S., Mulier, M., Zadpoor, A. A., Weinans, H., Van Humbeeck, J., Kruth, J.-P., & Schrooten, J. (2015) · Materials Science and Engineering: C · doi:10.1016/j.msec.2015.05.001 · Cited by 163
Compressive behaviour of gyroid lattice structures for human cancellous bone implant applications
Yánez, A., Herrera, A., Martel, O., Monopoli, D., & Afonso, H. (2016) · Materials Science and Engineering C · doi:10.1016/j.msec.2016.06.016 · Cited by 156
Liu, Z., & Qi, H. (2015) · Acta Materialia · doi:10.1016/j.actamat.2014.12.046 · Cited by 150
Wang, P., Tan, X., Nai, M. L. S., Tor, S. B., & Wei, J. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.01.093 · Cited by 140
Hedayati, R., Hosseini‐Toudeshky, H., Sadighi, M., Aghdam, M. M., & ZADPOOR, A. A. (2015) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2015.11.017 · Cited by 135
Yoo, D.-J., & Kim, K.-H. (2015) · International Journal of Precision Engineering and Manufacturing · doi:10.1007/s12541-015-0263-2 · Cited by 131
Kumar, A., Nune, K. C., Murr, L. E., & Misra, R. D. K. (2016) · International Materials Reviews · doi:10.1080/09506608.2015.1128310 · Cited by 127
Li, X., Humbeeck, J. V., & Kruth, J. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.12.019 · Cited by 117
Failure modes in high strength and stiffness to weight scaffolds produced by Selective Laser Melting
Sercombe, T. B., Xu, X., Challis, V. J., Green, R., Yue, S., Zhang, Z., & Lee, P. D. (2014) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2014.10.063 · Cited by 98
Effects of scaffold architecture on cranial bone healing
Berner, A., Woodruff, M. A., Lam, C. X. F., Arafat, M. T., Saifzadeh, S., Steck, R., Ren, J., Nerlich, M. L., Ekaputra, A. K., Gibson, I., et al. (2013) · International Journal of Oral and Maxillofacial Surgery · doi:10.1016/j.ijom.2013.05.008 · Cited by 98
Heterogeneous porous scaffold design for tissue engineering using triply periodic minimal surfaces
Yoo, D.-J. (2012) · International Journal of Precision Engineering and Manufacturing · doi:10.1007/s12541-012-0068-5 · Cited by 96
Lipiński, P., Barbas, A., & Bonnet, A.-S. (2013) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2013.08.011 · Cited by 68
Walker, J. M., Bodamer, E., Kleinfehn, A. P., Luo, Y., Becker, M. L., & Dean, D. (2017) · Progress in Additive Manufacturing · doi:10.1007/s40964-017-0021-3 · Cited by 64
Microstructural evolution of fusion zone in laser beam welds of pure titanium
Liu, H., Nakata, K., Zhang, J. X., Yamamoto, N., & Liao, J. (2011) · Materials Characterization · doi:10.1016/j.matchar.2011.12.010 · Cited by 62
Qin, Y., Geng, L., & Ni, D. R. (2011) · Journal of Materials Science · doi:10.1007/s10853-011-5415-x · Cited by 40
Yoo, D.-J. (2014) · International Journal of Precision Engineering and Manufacturing · doi:10.1007/s12541-014-0571-y · Cited by 27
Preparation of advanced porous structures by stereolithography for application in tissue engineering
Melchels, F. P. W. (2010) · doi:10.3990/1.9789036530194 · Cited by 11
Cited by
SLM lattice structures: Properties, performance, applications and challenges
Maconachie, T., Leary, M., Lozanovski, B., Zhang, X., Qian, M., Faruque, O., & Brandt, M. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.108137 · Cited by 1,497
Self-citationReview on titanium and titanium based alloys as biomaterials for orthopaedic applications
Kaur, M., & Singh, K. (2019) · Materials Science and Engineering: C · doi:10.1016/j.msec.2019.04.064 · Cited by 1,451
Multifunctional Mechanical Metamaterials Based on Triply Periodic Minimal Surface Lattices
Al-Ketan, O., & Abu Al-Rub, R. K. (2019) · Advanced Engineering Materials · doi:10.1002/adem.201900524 · Cited by 887
Chen, L.-Y., Liang, S.-X., Liu, Y., & Zhang, L.-C. (2021) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2021.100648 · Cited by 603
Yuan, L., Ding, S., & Wen, C. (2019) · Bioactive Materials · doi:10.1016/j.bioactmat.2018.12.003 · Cited by 593
Self-citation
Metadata
- Authors
- Ataee, A., Li, Y., Brandt, M., & Wen, C.
- Venue
- Acta Materialia
- Publisher
- Elsevier BV
- Published
- 2018-10
- Volume
- 158
- Pages
- 354-368
- ISSN
- 1359-6454 (ISSN-L)
- OpenAlex
- W2885940131
- Cited by
- 383
- References
- 65
- FWCI
- 20.47
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.