The DOI matches its Crossref record; 39 of the 39 references it cites were found in a registry or an index.
Thermal post-processing of AlSi10Mg parts produced by Selective Laser Melting using recycled powder
Open accessAbstract
The performance enhancement of parts produced using Selective Laser Melting (SLM) is an important goal for various industrial applications. In order to achieve this goal, obtaining a homogeneous microstructure and eliminating material defects within the fabricated parts are important research issues. The objective of this experimental study is to evaluate the effect of thermal post-processing of AlSi10Mg parts, using recycled powder, with the aim of improving the microstructure homogeneity of the as-built parts. This work is essential for the cost-effective additive manufacturing (AM) of metal optics and optomechanical systems. To achieve this goal, a full characterization of fresh and recycled powder was performed, in addition to a microstructure assessment of the as-built fabricated samples. Annealing, solution heat treatment (SHT) and T6 heat treatment (T6 HT) were applied under different processing conditions. The results demonstrated an improvement in microstructure homogeneity after thermal post-processing under specific conditions of SHT and T6 HT. A micro-hardness map was developed to assist in the selection of the optimized post-processing parameters in order to satisfy the design requirements of the part.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Scherrer after sixty years: A survey and some new results in the determination of crystallite size
Langford, J. I., & Wilson, A. J. C. (1978) · Journal of Applied Crystallography · doi:10.1107/s0021889878012844 · Cited by 3,903
Gibson, I., Rosen, D., & Stucker, B. (2015) · doi:10.1007/978-1-4939-2113-3 · Cited by 3,299
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
The metallurgy and processing science of metal additive manufacturing
Sames, W. J., List, F. A., Pannala, S., Dehoff, R. R., & Babu, S. S. (2016) · International Materials Reviews · doi:10.1080/09506608.2015.1116649 · Cited by 2,529
Thijs, L., Kempen, K., Kruth, J.-P., & Van Humbeeck, J. (2013) · Acta Materialia · doi:10.1016/j.actamat.2012.11.052 · Cited by 1,917
Reducing porosity in AlSi10Mg parts processed by selective laser melting
Aboulkhair, N. T., Everitt, N. M., Ashcroft, I., & Tuck, C. (2014) · Additive Manufacturing · doi:10.1016/j.addma.2014.08.001 · Cited by 1,281
Read, N., Wang, W., Essa, K., & Attallah, M. M. (2015) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2014.09.044 · Cited by 1,218
Li, W., Li, S., Liu, J., Zhang, A., Zhou, Y., Wei, Q., Yan, C., & Shi, Y. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2016.03.088 · Cited by 850
Hussein, A., Hao, L., Yan, C., & Everson, R. (2013) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2013.05.070 · Cited by 706
Aboulkhair, N. T., Maskery, I., Tuck, C., Ashcroft, I., & Everitt, N. M. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2016.04.092 · Cited by 675
Spierings, A. B., Herres, N., & Levy, G. (2011) · Rapid Prototyping Journal · doi:10.1108/13552541111124770 · Cited by 614
Formation of metastable cellular microstructures in selective laser melted alloys
Prashanth, K. G., & Eckert, J. (2016) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2016.12.209 · Cited by 597
Liu, Y. J., Li, S. J., Wang, H. L., Hou, W. T., Hao, Y. L., Yang, R., Sercombe, T. B., & Zhang, L. C. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.04.029 · Cited by 584
Change in microstructure of selectively laser melted AlSi10Mg alloy with heat treatments
Takata, N., Kodaira, H., Sekizawa, K., Suzuki, A., & Kobashi, M. (2017) · Materials Science and Engineering: A · doi:10.1016/j.msea.2017.08.029 · Cited by 574
Characterization of Metal Powders Used for Additive Manufacturing
Slotwinski, J. A., Garboczi, E. J., Stutzman, P. E., Ferraris, C. F., Watson, S. S., & Peltz, M. A. (2014) · Journal of Research of the National Institute of Standards and Technology · doi:10.6028/jres.119.018 · Cited by 506
Trevisan, F., Calignano, F., Lorusso, M., Pakkanen, J., Aversa, A., Ambrosio, E., Lombardi, M., Fino, P., & Manfredi, D. (2017) · Materials · doi:10.3390/ma10010076 · Cited by 502
Oxides, porosity and fatigue performance of AlSi10Mg parts produced by selective laser melting
Ming, T., & Pistorius, P. C. (2016) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2016.06.002 · Cited by 487
Tang, H. P., Qian, M., Liu, N., Zhang, X. Z., Yang, G. Y., & Wang, J. (2015) · JOM · doi:10.1007/s11837-015-1300-4 · Cited by 483
Olakanmi, E. O. (2013) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2013.03.009 · Cited by 418
Processing AlSi10Mg by selective laser melting: Parameter optimisation and material characterisation
Kempen, K., Thijs, L., Van Humbeeck, J., & Kruth, J.-P. (2015) · Materials Science and Technology · doi:10.1179/1743284714y.0000000702 · Cited by 410
Tan, J. H., Wong, W. L. E., & Dalgarno, K. W. (2017) · Additive Manufacturing · doi:10.1016/j.addma.2017.10.011 · Cited by 407
Hot isostatic pressing of IN718 components manufactured by selective laser melting
Tillmann, W., Schaak, C., Nellesen, J., Schaper, M., Aydinöz, M. E., & Hoyer, K.-P. (2017) · Additive Manufacturing · doi:10.1016/j.addma.2016.11.006 · Cited by 353
Gradient in microstructure and mechanical property of selective laser melted AlSi10Mg
Liu, Y., Liu, Z., Jiang, Y., Wang, G. W., Yang, Y., & Zhang, L. (2017) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2017.11.020 · Cited by 352
Tradowsky, U., White, J., Ward, R. M., Read, N., Reimers, W., & Attallah, M. M. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.05.066 · Cited by 332
On the Precipitation Hardening of Selective Laser Melted AlSi10Mg
Aboulkhair, N. T., Tuck, C., Ashcroft, I., Maskery, I., & Everitt, N. M. (2015) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-015-2980-7 · Cited by 286
Ardila, L. C., Garciandia, F., González-Díaz, J. B., Álvarez, P., Echeverria, A., Petite, M. M., Deffley, R., & Ochoa, J. (2014) · Physics Procedia · doi:10.1016/j.phpro.2014.08.152 · Cited by 268
Low temperature annealing dedicated to AlSi10Mg selective laser melting products
Fiocchi, J., Tuissi, A., Bassani, P., & Biffi, C. A. (2017) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2016.12.019 · Cited by 215
Asgari, H., Baxter, C., Hosseinkhani, K., & Mohammadi, M. (2017) · Materials Science and Engineering: A · doi:10.1016/j.msea.2017.09.041 · Cited by 201
Selective laser melting of aluminium and aluminium metal matrix composites: review
Sercombe, T. B., & Li, X. (2015) · Materials Technology · doi:10.1179/1753555715y.0000000078 · Cited by 188
Influence of Annealing on Mechanical Properties of Al-20Si Processed by Selective Laser Melting
Ma, P., Prashanth, K., Scudino, S., Jia, Y., Wang, H., Zou, C., Wei, Z., & Eckert, J. (2014) · Metals · doi:10.3390/met4010028 · Cited by 181
Damon, J., Dietrich, S., Vollert, F., Gibmeier, J., & Schulze, V. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2018.01.001 · Cited by 166
Liu, B., Wildman, R. D., Tuck, C. J., Ashcroft, I., & Hague, R. (2011) · doi:10.26153/tsw/15290 · Cited by 159
Srivatsan, T. S., & Sudarshan, T. S. (2015) · CRC Press eBooks · doi:10.1201/b19360 · Cited by 151
Anisotropic Mechanical Behavior of AlSi10Mg Parts Produced by Selective Laser Melting
Ming, T., & Pistorius, P. C. (2017) · JOM · doi:10.1007/s11837-016-2230-5 · Cited by 135
Kang, N., Coddet, P., Dembinski, L., Liao, H., & Coddet, C. (2016) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2016.08.249 · Cited by 132
Crawford, R., & Beaman, J. J. (1999) · IEEE Spectrum · doi:10.1109/6.744874 · Cited by 110
Aversa, A., Lorusso, M., Trevisan, F., Ambrosio, E. P., Calignano, F., Manfredi, D., Biamino, S., Fino, P., Lombardi, M., & Pavese, M. (2017) · Metals · doi:10.3390/met7020068 · Cited by 94
Manfredi, D., Ambrosio, E. P., Calignano, F., Krishnan, M., Canali, R., Biamino, S., Pavese, M., Atzeni, E., Iuliano, L., Fino, P., et al. (2013) · Frattura ed Integrità Strutturale · Cited by 82
Post-Processing of AM-SLM AlSi10Mg Specimens: Mechanical Properties and Fracture Behaviour
Rosenthal, I., Tiferet, E., Ganor, M., & Stern, A. (2015) · Cited by 17
Cited by
Aboulkhair, N. T., Simonelli, M., Parry, L., Ashcroft, I., Tuck, C., & Hague, R. (2019) · Progress in Materials Science · doi:10.1016/j.pmatsci.2019.100578 · Cited by 1,552
Making sustainable aluminum by recycling scrap: The science of “dirty” alloys
Raabe, D., Ponge, D., Uggowitzer, P. J., Roscher, M., Paolantonio, M., Liu, C., Antrekowitsch, H., Kozeschnik, E., Seidmann, D., Gault, B., et al. (2022) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.100947 · Cited by 626
Heat treatment for metal additive manufacturing
Laleh, M., Sadeghi, E., Revilla, R. I., Chao, Q., Haghdadi, N., Hughes, A. E., Xu, W., De Graeve, I., Qian, M., Gibson, I., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.101051 · Cited by 538
Powders for powder bed fusion: a review
Vock, S., Klöden, B., Kirchner, A., Weißgärber, T., & Kieback, B. (2019) · Progress in Additive Manufacturing · doi:10.1007/s40964-019-00078-6 · Cited by 500
State-of-the-art of selective laser melting process: A comprehensive review
Sefene, E. M. (2022) · Journal of Manufacturing Systems · doi:10.1016/j.jmsy.2022.04.002 · Cited by 429
Metadata
- Authors
- Maamoun, A. H., Elbestawi, M., Dosbaeva, G. K., & Veldhuis, S. C.
- Venue
- Additive Manufacturing
- Publisher
- Elsevier BV
- Published
- 2018-05
- Volume
- 21
- Pages
- 234-247
- ISSN
- 2214-7810 (ISSN-L)
- 2214-8604
- OpenAlex
- W2790587781
- Cited by
- 270
- References
- 39
- FWCI
- 16.47
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.