The DOI matches its Crossref record; 45 of the 45 references it cites were found in a registry or an index.
A critical review of the use of 3-D printing in the construction industry
Open accessAbstract
Abstract 3-D printing, which is an automated production process with layer-by-layer control, has been gaining rapid development in recent years. The technology has been adopted in the manufacturing industry for decades and has recently been introduced in the construction industry to print houses and villas. The technology can bring significant benefits to the construction industry in terms of increased customization, reduced construction time, reduced manpower, and construction cost. A few isolated products and projects have been preliminarily tested using the 3-D printing technology. However, it should be noted that such tests and developments on the use of 3-D printing in the construction industry are very fragmented at the time of the study. It is therefore necessary for the building and construction industry to understand the technology, its historical applications and challenges for better utilization in the future. A systematic review shows that 3-D printing technology, after years of evolution, can be used to print large-scale architectural models and buildings. However, the potential of the technology is limited by the lack of large-scale implementation, the development of building information modeling, the requirements of mass customization, and the life cycle cost of the printed projects. It is therefore expected that future studies should be conducted on these areas to consolidate the stability and expand the applicability of 3-D printing in the construction industry.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Managing Innovation: Integrating Technological, Market and Organizational Change
Tidd, J., Bessant, J., & Pavitt, K. (1997) · University of Maribor digital library (University of Maribor) · Cited by 4,199
Eastman, C., Teicholz, P. M., Sacks, R., & Liston, K. (2008) · Cited by 2,892
3-D printing: The new industrial revolution
Berman, B. (2012) · Business Horizons · doi:10.1016/j.bushor.2011.11.003 · Cited by 2,481
A review on stereolithography and its applications in biomedical engineering
Melchels, F. P. W., Feijen, J., & Grijpma, D. W. (2010) · Biomaterials · doi:10.1016/j.biomaterials.2010.04.050 · Cited by 2,457
Inkjet Printing of Polymers: State of the Art and Future Developments
de Gans, B. ‐., Duineveld, P. C., & Schubert, U. S. (2004) · Advanced Materials · doi:10.1002/adma.200300385 · Cited by 1,906
Managing Innovation: Integrating Technological, Market and Organizational Change
Hayward, G. (1998) · Technovation · doi:10.1016/s0166-4972(98)80033-3 · Cited by 1,856
Product design for manufacture and assembly
Boothroyd, G. (1994) · Computer-Aided Design · doi:10.1016/0010-4485(94)90082-5 · Cited by 1,726
Selective laser melting of iron-based powder
Kruth, J. P., Froyen, L., Van Vaerenbergh, J., Mercelis, P., Rombouts, M., & Lauwers, B. (2004) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2003.11.051 · Cited by 1,550
Wang, X. (2012) · Construction Economics and Building · doi:10.5130/ajceb.v12i3.2749 · Cited by 1,495
Self-citationBinding mechanisms in selective laser sintering and selective laser melting
Kruth, J., Mercelis, P., Van Vaerenbergh, J., Froyen, L., & Rombouts, M. (2005) · Rapid Prototyping Journal · doi:10.1108/13552540510573365 · Cited by 1,383
Mix design and fresh properties for high-performance printing concrete
Le, T. T., Austin, S. A., Lim, S., Buswell, R. A., Gibb, A. G. F., & Thorpe, T. (2012) · Materials and Structures · doi:10.1617/s11527-012-9828-z · Cited by 1,218
Developments in construction-scale additive manufacturing processes
Lim, S., Buswell, R. A., Le, T. T., Austin, S. A., Gibb, A. G. F., & Thorpe, T. (2012) · Automation in Construction · doi:10.1016/j.autcon.2011.06.010 · Cited by 1,205
Automated construction by contour crafting—related robotics and information technologies
Khoshnevis, B. (2004) · Automation in Construction · doi:10.1016/j.autcon.2003.08.012 · Cited by 1,161
Hardened properties of high-performance printing concrete
Le, T. T., Austin, S. A., Lim, S., Buswell, R. A., Law, R., Gibb, A. G. F., & Thorpe, T. (2012) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.12.003 · Cited by 1,020
Freeform Construction: Mega-scale Rapid Manufacturing for construction
Buswell, R. A., Soar, R. C., Gibb, A. G. F., & Thorpe, A. (2007) · Automation in Construction · doi:10.1016/j.autcon.2006.05.002 · Cited by 536
Butscher, A., Bohner, M., Hofmann, S., Gauckler, L., & Müller, R. (2011) · Acta Biomaterialia · doi:10.1016/j.actbio.2010.09.039 · Cited by 459
Advances in three dimensional printing – state of the art and future perspectives
Dimitrov, D., Schreve, K., & de Beer, N. (2006) · Rapid Prototyping Journal · doi:10.1108/13552540610670717 · Cited by 446
Gann, D. M. (1996) · Construction Management and Economics · doi:10.1080/014461996373304 · Cited by 385
3D printing: the dawn of a new era in manufacturing?
Bogue, R. (2013) · Assembly Automation · doi:10.1108/aa-06-2013-055 · Cited by 371
Rapid prototyping or rapid production? 3D printing processes move industry towards the latter
Bak, D. (2003) · Assembly Automation · doi:10.1108/01445150310501190 · Cited by 353
Supply strategy and network effects — purchasing behaviour in the construction industry
Dubois, A., & Gadde, L.-E. (2000) · European Journal of Purchasing & Supply Management · doi:10.1016/s0969-7012(00)00016-2 · Cited by 313
Disruptions, decisions, and destinations: Enter the age of 3-D printing and additive manufacturing
Kietzmann, J., Pitt, L., & Berthon, P. (2015) · Business Horizons · doi:10.1016/j.bushor.2014.11.005 · Cited by 307
BIM adoption and implementation for architectural practices
Arayıcı, Y., Coates, P., Koskela, L., Kagioglou, M., Usher, C., & O'Reilly, K. (2011) · International Journal of Building Pathology and Adaptation · doi:10.1108/02630801111118377 · Cited by 279
3-D Printing of Open Source Appropriate Technologies for Self-Directed Sustainable Development
Pearce, J. M., Morris Blair, C., Laciak, K. J., Andrews, R., Nosrat, A., & Zelenika-Zovko, I. (2010) · Journal of Sustainable Development · doi:10.5539/jsd.v3n4p17 · Cited by 271
Construction productivity: Issues encountered by contractors in Singapore
Lim, E., & Alum, J. (1995) · International Journal of Project Management · doi:10.1016/0263-7863(95)95704-h · Cited by 241
Implementing innovation in construction: contexts, relative boundedness and actor‐network theory
Harty, C. (2008) · Construction Management and Economics · doi:10.1080/01446190802298413 · Cited by 241
Cox, A., & Thompson, I. (1997) · European Journal of Purchasing & Supply Management · doi:10.1016/s0969-7012(97)00005-1 · Cited by 207
Materializing design: the implications of rapid prototyping in digital design
Sass, L., & Oxman, R. (2006) · Design Studies · doi:10.1016/j.destud.2005.11.009 · Cited by 189
Integrating BIM and LiDAR for Real-Time Construction Quality Control
Wang, J., Sun, W., Shou, W., Wang, X., Wu, C., Chong, H.-Y., Liu, Y., & Sun, C. (2015) · Journal of Intelligent & Robotic Systems · doi:10.1007/s10846-014-0116-8 · Cited by 180
Self-citationArayıcı, Y., Egbu, C., & Coates, P. M. (2012) · University of Salford Institutional Repository (University of Salford) · Cited by 173
Shou, W., Wang, J., Wang, X., & Chong, H. (2014) · Archives of Computational Methods in Engineering · doi:10.1007/s11831-014-9125-9 · Cited by 154
Self-citationThe Intellectual Property Implications of Low-Cost 3D Printing
Bradshaw, S., Bowyer, A., & Haufe, P. (2010) · SCRIPTed A Journal of Law Technology & Society · doi:10.2966/scrip.070110.5 · Cited by 144
Stereolithography for the fabrication of ceramic three‐ dimensional parts
Hinczewski, C., Corbel, S., & Chartier, T. (1998) · Rapid Prototyping Journal · doi:10.1108/13552549810222867 · Cited by 143
Lü, N., & Korman, T. M. (2010) · ASCE Construction Research Congress (CRC) · doi:10.1061/41109(373)114 · Cited by 139
Experimental investigation of contour crafting using ceramics materials
Khoshnevis, B., Bukkapatnam, S., Kwon, H., & Saito, J. (2001) · Rapid Prototyping Journal · doi:10.1108/13552540110365144 · Cited by 134
Chi, H.-L., Wang, X., & Jiao, Y. (2014) · Archives of Computational Methods in Engineering · doi:10.1007/s11831-014-9127-7 · Cited by 104
Self-citationMass‐customisation in marketing: the consumer perspective
Bardakçı, A., & Whitelock, J. M. (2003) · Journal of Consumer Marketing · doi:10.1108/07363760310489689 · Cited by 102
Agility through rapid prototyping technology in a manufacturing environment using a 3D printer
Vinodh, S., Sundararaj, G., Devadasan, S. R., Kuttalingam, D., & Rajanayagam, D. (2009) · Journal of Manufacturing Technology Management · doi:10.1108/17410380910984267 · Cited by 81
Khoshnevis, B., Russell, R., Kwon, H., & Bukkapatnam, S. (2001) · IEEE Robotics & Automation Magazine · doi:10.1109/100.956812 · Cited by 71
Kang, H., & Cho, D. (2012) · Tissue Engineering Part C Methods · doi:10.1089/ten.tec.2011.0621 · Cited by 66
Managing the Embodied Carbon of Precast Concrete Columns
Wu, P., & Pheng, L. S. (2011) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0000287 · Cited by 62
Self-citationApplicability and Limitations of 3D Printing for Civil Structures
Yossef, M., & Chen, A. B. (2015) · Iowa State University Digital Repository (Iowa State University) · Cited by 43
Barbosa, G. F., Barbosa, G. F., de Carvalho, J., & de Carvalho, J. (2013) · Journal of the Brazilian Society of Mechanical Sciences and Engineering · doi:10.1007/s40430-013-0103-1 · Cited by 21
Chi, H.-L., Wang, J., Wang, X., et al. (2014) · Journal of Intelligent & Robotic Systems · doi:10.1007/s10846-014-0123-9 · Cited by 20
Self-citationDistributed Intelligence in Design
Kiviniemi, A. (2011) · Wiley eBooks · doi:10.1002/9781444392395 · Cited by 18
Cited by
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
3D printing using concrete extrusion: A roadmap for research
Buswell, R. A., Leal de Silva, W. R., Jones, S. Z., & Dirrenberger, J. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.05.006 · Cited by 1,604
Bos, F., Wolfs, R., Ahmed, Z., & Salet, T. (2016) · Virtual and Physical Prototyping · doi:10.1080/17452759.2016.1209867 · Cited by 1,257
Vision of 3D printing with concrete — Technical, economic and environmental potentials
De Schutter, G., Lesage, K., Mechtcherine, V., Nerella, V. N., Habert, G., & Agusti-Juan, I. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.06.001 · Cited by 1,072
3D printing trends in building and construction industry: a review
Tay, Y. W. D., Panda, B., Paul, S. C., Noor Mohamed, N. A., Tan, M. J., & Leong, K. F. (2017) · Virtual and Physical Prototyping · doi:10.1080/17452759.2017.1326724 · Cited by 868
Metadata
- Authors
- Wu, P., Wang, J., & Wang, X.
- Venue
- Automation in Construction
- Publisher
- Elsevier BV
- Published
- 2016-08
- Volume
- 68
- Pages
- 21-31
- ISSN
- 0926-5805 (ISSN-L)
- OpenAlex
- W2344513838
- Cited by
- 1,002
- References
- 45
- FWCI
- 55.18
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.