The DOI matches its Crossref record; 45 of the 45 references it cites were found in a registry or an index.
A critical review of the use of 3-D printing in the construction industry
Open accessAbstract
Abstract 3-D printing, which is an automated production process with layer-by-layer control, has been gaining rapid development in recent years. The technology has been adopted in the manufacturing industry for decades and has recently been introduced in the construction industry to print houses and villas. The technology can bring significant benefits to the construction industry in terms of increased customization, reduced construction time, reduced manpower, and construction cost. A few isolated products and projects have been preliminarily tested using the 3-D printing technology. However, it should be noted that such tests and developments on the use of 3-D printing in the construction industry are very fragmented at the time of the study. It is therefore necessary for the building and construction industry to understand the technology, its historical applications and challenges for better utilization in the future. A systematic review shows that 3-D printing technology, after years of evolution, can be used to print large-scale architectural models and buildings. However, the potential of the technology is limited by the lack of large-scale implementation, the development of building information modeling, the requirements of mass customization, and the life cycle cost of the printed projects. It is therefore expected that future studies should be conducted on these areas to consolidate the stability and expand the applicability of 3-D printing in the construction industry.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Managing Innovation: Integrating Technological, Market and Organizational Change
Tidd, J., Bessant, J., & Pavitt, K. (1997) · University of Maribor digital library (University of Maribor) · Cited by 4,405
Eastman, C., Teicholz, P. M., Sacks, R., & Liston, K. (2008) · Cited by 2,892
3-D printing: The new industrial revolution
Berman, B. (2012) · Business Horizons · doi:10.1016/j.bushor.2011.11.003 · Cited by 2,481
A review on stereolithography and its applications in biomedical engineering
Melchels, F. P. W., Feijen, J., & Grijpma, D. W. (2010) · Biomaterials · doi:10.1016/j.biomaterials.2010.04.050 · Cited by 2,457
Inkjet Printing of Polymers: State of the Art and Future Developments
de Gans, B. ‐., Duineveld, P. C., & Schubert, U. S. (2004) · Advanced Materials · doi:10.1002/adma.200300385 · Cited by 1,906
Managing Innovation: Integrating Technological, Market and Organizational Change
Hayward, G. (1998) · Technovation · doi:10.1016/s0166-4972(98)80033-3 · Cited by 1,856
Product design for manufacture and assembly
Boothroyd, G. (1994) · Computer-Aided Design · doi:10.1016/0010-4485(94)90082-5 · Cited by 1,726
Selective laser melting of iron-based powder
Kruth, J. P., Froyen, L., Van Vaerenbergh, J., Mercelis, P., Rombouts, M., & Lauwers, B. (2004) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2003.11.051 · Cited by 1,550
Wang, X. (2012) · Construction Economics and Building · doi:10.5130/ajceb.v12i3.2749 · Cited by 1,495
Self-citationBinding mechanisms in selective laser sintering and selective laser melting
Kruth, J., Mercelis, P., Van Vaerenbergh, J., Froyen, L., & Rombouts, M. (2005) · Rapid Prototyping Journal · doi:10.1108/13552540510573365 · Cited by 1,383
Cited by
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
3D printing using concrete extrusion: A roadmap for research
Buswell, R. A., Leal de Silva, W. R., Jones, S. Z., & Dirrenberger, J. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.05.006 · Cited by 1,604
Bos, F., Wolfs, R., Ahmed, Z., & Salet, T. (2016) · Virtual and Physical Prototyping · doi:10.1080/17452759.2016.1209867 · Cited by 1,257
Vision of 3D printing with concrete — Technical, economic and environmental potentials
De Schutter, G., Lesage, K., Mechtcherine, V., Nerella, V. N., Habert, G., & Agusti-Juan, I. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.06.001 · Cited by 1,072
3D printing trends in building and construction industry: a review
Tay, Y. W. D., Panda, B., Paul, S. C., Noor Mohamed, N. A., Tan, M. J., & Leong, K. F. (2017) · Virtual and Physical Prototyping · doi:10.1080/17452759.2017.1326724 · Cited by 868
Buchanan, C., & Gardner, L. (2019) · Engineering Structures · doi:10.1016/j.engstruct.2018.11.045 · Cited by 826
Paolini, A., Kollmannsberger, S., & Rank, E. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.100894 · Cited by 673
Ma, G., Li, Z., & Wang, L. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.12.051 · Cited by 616
Wangler, T., Roussel, N., Bos, F. P., Salet, T. A. M., & Flatt, R. J. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2019.105780 · Cited by 612
Davila Delgado, J. M., Oyedele, L., Ajayi, A., Akanbi, L., Akinade, O., Bilal, M., & Owolabi, H. (2019) · Journal of Building Engineering · doi:10.1016/j.jobe.2019.100868 · Cited by 607
Nerella, V. N., Hempel, S., & Mechtcherine, V. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.01.235 · Cited by 605
Measurement of tensile bond strength of 3D printed geopolymer mortar
Panda, B., Paul, S. C., Mohamed, N. A. N., Tay, Y. W. D., & Tan, M. J. (2018) · Measurement · doi:10.1016/j.measurement.2017.08.051 · Cited by 592
Applications of additive manufacturing in the construction industry – A forward-looking review
Delgado Camacho, D., Clayton, P., O'Brien, W. J., Seepersad, C., Juenger, M., Ferron, R., & Salamone, S. (2018) · Automation in Construction · doi:10.1016/j.autcon.2017.12.031 · Cited by 538
Panda, B., & Tan, M. J. (2018) · Ceramics International · doi:10.1016/j.ceramint.2018.03.031 · Cited by 520
Additive manufacturing of geopolymer for sustainable built environment
Panda, B., Paul, S. C., Hui, L. J., Tay, Y. W. D., & Tan, M. J. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.08.165 · Cited by 516
Additive Manufacturing Technologies: An Overview about 3D Printing Methods and Future Prospects
Jiménez, M., Romero, L., Domínguez, I. A., Espinosa, M. D. M., & Domínguez, M. (2019) · Complexity · doi:10.1155/2019/9656938 · Cited by 509
Fused deposition modelling: Current status, methodology, applications and future prospects
Cano-Vicent, A., Tambuwala, M. M., Hassan, S. S., Barh, D., Aljabali, A. A. A., Birkett, M., Arjunan, A., & Serrano-Aroca, Á. (2021) · Additive Manufacturing · doi:10.1016/j.addma.2021.102378 · Cited by 509
Craveiro, F., Duarte, J. P., Bartolo, H., & Bartolo, P. J. (2019) · Automation in Construction · doi:10.1016/j.autcon.2019.03.011 · Cited by 455
Large-scale digital concrete construction – CONPrint3D concept for on-site, monolithic 3D-printing
Mechtcherine, V., Nerella, V. N., Will, F., Näther, M., Otto, J., & Krause, M. (2019) · Automation in Construction · doi:10.1016/j.autcon.2019.102933 · Cited by 455
A scientometric review of global BIM research: Analysis and visualization
Zhao, X. (2017) · Automation in Construction · doi:10.1016/j.autcon.2017.04.002 · Cited by 434
The role of early age structural build-up in digital fabrication with concrete
Reiter, L., Wangler, T., Roussel, N., & Flatt, R. J. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.05.011 · Cited by 432
Mix design concepts for 3D printable concrete: A review
Zhang, C., Nerella, V. N., Krishna, A., Wang, S., Zhang, Y., Mechtcherine, V., & Banthia, N. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104155 · Cited by 421
A critical review of 3D printing in construction: benefits, challenges, and risks
El-Sayegh, S., Romdhane, L., & Manjikian, S. (2020) · Archives of Civil and Mechanical Engineering · doi:10.1007/s43452-020-00038-w · Cited by 387
Rethinking reinforcement for digital fabrication with concrete
Asprone, D., Menna, C., Bos, F. P., Salet, T. A. M., Mata-Falcón, J., & Kaufmann, W. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.05.020 · Cited by 385
Current status and future directions of fused filament fabrication
Singh, S., Singh, G., Prakash, C., & Ramakrishna, S. (2020) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2020.04.049 · Cited by 385
Extrusion-based concrete 3D printing from a material perspective: A state-of-the-art review
Mohan, M. K., Rahul, A. V., De Schutter, G., & Van Tittelboom, K. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2020.103855 · Cited by 384
Recent advances in the concrete industry to reduce its carbon dioxide emissions
Adesina, A. (2020) · Environmental Challenges · doi:10.1016/j.envc.2020.100004 · Cited by 384
Ghaffar, S. H., Corker, J., & Fan, M. (2018) · Automation in Construction · doi:10.1016/j.autcon.2018.05.005 · Cited by 358
On-site autonomous construction robots: Towards unsupervised building
Melenbrink, N., Werfel, J., & Menges, A. (2020) · Automation in Construction · doi:10.1016/j.autcon.2020.103312 · Cited by 350
Mesh reinforcing method for 3D Concrete Printing
Marchment, T., & Sanjayan, J. (2020) · Automation in Construction · doi:10.1016/j.autcon.2019.102992 · Cited by 347
A self-reinforced cementitious composite for building-scale 3D printing
Soltan, D. G., & Li, V. C. (2018) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2018.03.017 · Cited by 330
A Review of 3D Printing in Construction and its Impact on the Labor Market
Hossain, M. A., Zhumabekova, A., Paul, S. C., & Kim, J. R. (2020) · Sustainability · doi:10.3390/su12208492 · Cited by 319
Construction 4.0: A Literature Review
Forcael, E., Ferrari, I., Opazo-Vega, A., & Pulido-Arcas, J. A. (2020) · Sustainability · doi:10.3390/su12229755 · Cited by 319
Printed aerogels: chemistry, processing, and applications
Feng, J., Su, B.-L., Xia, H., Zhao, S., Gao, C., Wang, L., Ogbeide, O., Feng, J., & Hasan, T. (2021) · Chemical Society Reviews · doi:10.1039/c9cs00757a · Cited by 313
Steel fibres reinforced 3D printed concrete: Influence of fibre sizes on mechanical performance
Pham, L., Tran, P., & Sanjayan, J. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.118785 · Cited by 296
Cements in the 21 st century: Challenges, perspectives, and opportunities
Biernacki, J. J., Bullard, J. W., Sant, G., Brown, K., Glasser, F. P., Jones, S., Ley, T., Livingston, R., Nicoleau, L., Olek, J., et al. (2017) · Journal of the American Ceramic Society · doi:10.1111/jace.14948 · Cited by 276
Experimental Exploration of Metal Cable as Reinforcement in 3D Printed Concrete
Bos, F., Ahmed, Z., Jutinov, E., & Salet, T. (2017) · Materials · doi:10.3390/ma10111314 · Cited by 276
Souza, M. T., Ferreira, I. M., Guzi de Moraes, E., Senff, L., & Novaes de Oliveira, A. P. (2020) · Journal of Building Engineering · doi:10.1016/j.jobe.2020.101833 · Cited by 268
Liu, C., Wang, X., Chen, Y., Zhang, C., Ma, L., Deng, Z., Chen, C., Zhang, Y., Pan, J., & Banthia, N. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104158 · Cited by 266
Self-citationMa, G., Wang, L., & Ju, Y. (2018) · Science China Technological Sciences · doi:10.1007/s11431-016-9077-7 · Cited by 261
Al Rashid, A., Khan, S. A., G. Al-Ghamdi, S., & Koç, M. (2020) · Automation in Construction · doi:10.1016/j.autcon.2020.103268 · Cited by 257
Literature review of digital twins applications in construction workforce safety
Hou, L., Wu, S., Zhang, G. (., Tan, Y., & Wang, X. (2020) · Applied Sciences · doi:10.3390/app11010339 · Cited by 194
Computer vision for real-time extrusion quality monitoring and control in robotic construction
Kazemian, A., Yuan, X., Davtalab, O., & Khoshnevis, B. (2019) · Automation in Construction · doi:10.1016/j.autcon.2019.01.022 · Cited by 170
Current Status and Prospects of Polymer Powder 3D Printing Technologies
Wang, Y., Xu, Z., Wu, D., & Bai, J. (2020) · Materials · doi:10.3390/ma13102406 · Cited by 124
Deep Learning-Based Applications for Safety Management in the AEC Industry: A Review
Hou, L., Chen, H., Zhang, G. (., & Wang, X. (2021) · Applied Sciences · doi:10.3390/app11020821 · Cited by 76
Self-citation
Metadata
- Authors
- Wu, P., Wang, J., & Wang, X.
- Venue
- Automation in Construction
- Publisher
- Elsevier BV
- Published
- 2016-08
- Volume
- 68
- Pages
- 21-31
- ISSN
- 0926-5805 (ISSN-L)
- OpenAlex
- W2344513838
- Cited by
- 1,002
- References
- 45
- FWCI
- 55.18
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.