The DOI matches its Crossref record; 31 of the 31 references it cites were found in a registry or an index.
Hardened properties of layered 3D printed concrete with recycled sand
Abstract
Abstract 3D concrete printing has received worldwide attention while the development on new cementitious material compositions for 3D printing is inadequate. This study employed the recycled sand instead of natural sand to achieve 3D concrete printing and investigated the hardened properties of this extrusion-based material. The effect of replacement ratio of recycled sand, curing age, nozzle height and anisotropic behavior were evaluated based on the compressive tests, tensile splitting tests and flexural tests. Moreover, the digital image correlation (DIC) technique was adopted to capture the strain behavior and failure pattern of this layered and printed concrete. Owing to the high un-hydrated cement paste attached to the recycled sand and the internal curing mechanism, the compressive and flexural strengths of the 3D printed concrete with recycled sand were a little lower than those specimens without recycled sand. The compressive, tensile splitting and flexural strength of 3D printed concrete with recycled sand had obvious anisotropy. The replacement of recycled sand had limited effect on the anisotropy of compressive and flexural strength, but had certain effect on the tensile splitting strength. Since recycled sand is one of those major products derived from the construction and demolition waste, it is believed that the employment of recycled sand to the mix of 3D printed concrete will significantly improve the sustainability of 3D printed concrete structures.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
3D printing using concrete extrusion: A roadmap for research
Buswell, R. A., Leal de Silva, W. R., Jones, S. Z., & Dirrenberger, J. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.05.006 · Cited by 1,604
Bos, F., Wolfs, R., Ahmed, Z., & Salet, T. (2016) · Virtual and Physical Prototyping · doi:10.1080/17452759.2016.1209867 · Cited by 1,257
Mix design and fresh properties for high-performance printing concrete
Le, T. T., Austin, S. A., Lim, S., Buswell, R. A., Gibb, A. G. F., & Thorpe, T. (2012) · Materials and Structures · doi:10.1617/s11527-012-9828-z · Cited by 1,218
Developments in construction-scale additive manufacturing processes
Lim, S., Buswell, R. A., Le, T. T., Austin, S. A., Gibb, A. G. F., & Thorpe, T. (2012) · Automation in Construction · doi:10.1016/j.autcon.2011.06.010 · Cited by 1,205
Automated construction by contour crafting—related robotics and information technologies
Khoshnevis, B. (2004) · Automation in Construction · doi:10.1016/j.autcon.2003.08.012 · Cited by 1,161
Vision of 3D printing with concrete — Technical, economic and environmental potentials
De Schutter, G., Lesage, K., Mechtcherine, V., Nerella, V. N., Habert, G., & Agusti-Juan, I. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.06.001 · Cited by 1,072
Mechanical behaviour of concrete made with fine recycled concrete aggregates
Evangelista, L., & de Brito, J. (2007) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2006.12.004 · Cited by 1,059
Hardened properties of high-performance printing concrete
Le, T. T., Austin, S. A., Lim, S., Buswell, R. A., Law, R., Gibb, A. G. F., & Thorpe, T. (2012) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.12.003 · Cited by 1,020
A global sustainability perspective on 3D printing technologies
Gebler, M., Schoot Uiterkamp, A. J. M., & Visser, C. (2014) · Energy Policy · doi:10.1016/j.enpol.2014.08.033 · Cited by 950
Properties of concrete incorporating fine recycled aggregate
Khatib, J. (2004) · Cement and Concrete Research · doi:10.1016/j.cemconres.2004.06.017 · Cited by 886
Wolfs, R. J. M., Bos, F. P., & Salet, T. A. M. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2019.02.017 · Cited by 836
Effect of surface moisture on inter-layer strength of 3D printed concrete
Sanjayan, J., Nematollahi, B., Xia, M., & Marchment, T. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.03.232 · Cited by 713
Fresh and hardened properties of 3D printable cementitious materials for building and construction
Paul, S. C., Tay, Y. W. D., Panda, B., & Tan, M. J. (2018) · Archives of Civil and Mechanical Engineering · doi:10.1016/j.acme.2017.02.008 · Cited by 633
Additive construction: State-of-the-art, challenges and opportunities
Labonnote, N., Rønnquist, A., Manum, B., & Rüther, P. (2016) · Automation in Construction · doi:10.1016/j.autcon.2016.08.026 · Cited by 607
Mechanical anisotropy of aligned fiber reinforced composite for extrusion-based 3D printing
Ma, G., Li, Z., Li, W., Wang, F., & Sanjayan, J. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.01.008 · Cited by 597
Panda, B., & Tan, M. J. (2018) · Ceramics International · doi:10.1016/j.ceramint.2018.03.031 · Cited by 520
Additive manufacturing of geopolymer for sustainable built environment
Panda, B., Paul, S. C., Hui, L. J., Tay, Y. W. D., & Tan, M. J. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.08.165 · Cited by 516
Properties of 3D-printed fiber-reinforced Portland cement paste
Hambach, M., & Volkmer, D. (2017) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2017.02.001 · Cited by 470
Rethinking reinforcement for digital fabrication with concrete
Asprone, D., Menna, C., Bos, F. P., Salet, T. A. M., Mata-Falcón, J., & Kaufmann, W. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.05.020 · Cited by 385
Compressive behaviour of recycled aggregate concrete under impact loading
Xiao, J., Li, L., Shen, L., & Poon, C. S. (2015) · Cement and Concrete Research · doi:10.1016/j.cemconres.2015.01.014 · Cited by 337
Self-citationInfluence of fine recycled concrete aggregates on the properties of mortars
Zhao, Z., Rémond, S., Damidot, D., & Xu, W. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2015.02.037 · Cited by 320
Use of fine recycled aggregates from ceramic waste in masonry mortar manufacturing
Jiménez, J. R., Ayuso, J., López, M., Fernández, J. M., & de Brito, J. (2012) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2012.11.036 · Cited by 213
Khoshnevis, B., & Dutton, R. (1998) · Materials Technology · doi:10.1080/10667857.1998.11752766 · Cited by 207
Adessina, A., Fraj, A. B., Barthélémy, J., Chateau, C., & Garnier, D. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2019.105900 · Cited by 196
Panda, B., Ruan, S., Unluer, C., & Tan, M. J. (2020) · Composites Part B Engineering · doi:10.1016/j.compositesb.2020.107826 · Cited by 192
Mechanical behavior of 3D printed mortar with recycled sand at early ages
Ding, T., Xiao, J., Qin, F., & Duan, Z. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.118654 · Cited by 179
Self-citationUtilization of recycled glass for 3D concrete printing: rheological and mechanical properties
Ting, G. H. A., Tay, Y. W. D., Qian, Y., & Tan, M. J. (2019) · Journal of Material Cycles and Waste Management · doi:10.1007/s10163-019-00857-x · Cited by 140
Effect of Recycled Sand Content on Characteristics of Mortars and Concretes
Dapena, E., Alaejos, P., Lobet, A., & Perez, D. J. (2010) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0000183 · Cited by 136
Ji, G., Ding, T., Xiao, J., Du, S., Li, J., & Duan, Z. (2019) · Materials · doi:10.3390/ma12091540 · Cited by 135
Self-citationJiang, J., Zhou, W., Gao, Y. X., Wang, L., Wang, F., Chu, H., Xu, G., Vandevyvere, B., Sierens, Z., & Li, J. (2018) · Waste Management · doi:10.1016/j.wasman.2018.11.005 · Cited by 91
Ma, G., Zhang, J., Li, W., Li, Z., & Sun, J. (2018) · Smart Materials and Structures · doi:10.1088/1361-665x/aac789 · Cited by 85
Cited by
Large-scale 3D printing concrete technology: Current status and future opportunities
Xiao, J., Ji, G., Zhang, Y., Ma, G., Mechtcherine, V., Pan, J., Wang, L., Ding, T., Duan, Z., & Du, S. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104115 · Cited by 532
Self-citationMix design concepts for 3D printable concrete: A review
Zhang, C., Nerella, V. N., Krishna, A., Wang, S., Zhang, Y., Mechtcherine, V., & Banthia, N. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104155 · Cited by 421
Environmental and economic assessment on 3D printed buildings with recycled concrete
Han, Y., Yang, Z., Ding, T., & Xiao, J. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.123884 · Cited by 322
Self-citationAnisotropic behavior in bending of 3D printed concrete reinforced with fibers
Ding, T., Xiao, J., Zou, S., & Zhou, X. (2020) · Composite Structures · doi:10.1016/j.compstruct.2020.112808 · Cited by 296
Self-citationYe, J., Cui, C., Yu, J., Yu, K., & Dong, F. (2021) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2021.122586 · Cited by 262
Metadata
- Authors
- Ding, T., Xiao, J., Zou, S., & Wang, Y.
- Venue
- Cement and Concrete Composites
- Publisher
- Elsevier BV
- Published
- 2020-10
- Volume
- 113
- Pages
- 103724
- ISSN
- 0958-9465 (ISSN-L)
- OpenAlex
- W3037300843
- Cited by
- 306
- References
- 31
- FWCI
- 18.74
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.