The DOI matches its Crossref record; 30 of the 30 references it cites were found in a registry or an index.
Impact damage resistance of 3D printed continuous fibre reinforced thermoplastic composites using fused deposition modelling
Open accessAbstract
Abstract Fused deposition modelling (FDM) is a promising additive manufacturing technology and an alternative of conventional processes for the fabrication of fibre reinforced composites due to its ability to build functional parts having complex geometries. Continuous fibre reinforced thermoplastic composites (CFRTPCs) are becoming more significant in industrial applications due to their inherit advantages such as excellent mechanical performance, recycling and potential lightweight structures [1,2]. However, a major concern affecting the efficient use of 3D printed composites is the effect of impact damage on the structural integrity, compared to conventional pre-preg composites. The aim of this study is to evaluate the effect of build orientation, layer thickness and fibre volume content on the impact performance of 3D printed continuous carbon, glass, and Kevlar® fibre reinforced nylon composites, manufactured by FDM technique. Charpy impact tests are carried out to determine impact strength. SEM images of fractured surfaces are examined to assess failure mechanics of the different configurations. It is observed that the effect of layer thickness of nylon samples on the impact performance was different for flat and on-edge samples. Impact strength increases as layer thickness increases in flat samples but, conversely, it decreases in on-edge samples, depicting a more brittle fracture. In addition, the results show that impact strength increases as fibre volume content increases in most cases. Glass fibre reinforced samples exhibits the highest impact strength and carbon fibre reinforced samples the lowest one and similar to nylon performance. Furthermore, on-edge reinforced samples exhibit higher values of impact strength than flat reinforced samples. Finally, the results obtained demonstrate that impact strength exhibited by 3D printed composites are significantly higher than the usual 3D printed thermoplastics and, in some cases, even better than common pre-preg materials.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
3D printing of polymer matrix composites: A review and prospective
Wang, X., Jiang, M., Zhou, Z., Gou, J., & Hui, D. (2017) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2016.11.034 · Cited by 3,325
Chacón, J. M., Caminero, M. A., García-Plaza, E., & Núñez, P. J. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.03.065 · Cited by 1,603
Self-citationImpact on Composite Structures
Abrate, S. (1998) · Cambridge University Press eBooks · doi:10.1017/cbo9780511574504 · Cited by 1,534
Mechanical characterization of 3D-printed polymers
Dizon, J. R. C., Espera, A. H., Chen, Q., & Advincula, R. C. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2017.12.002 · Cited by 1,340
A review on additive manufacturing of polymer-fiber composites
Parandoush, P., & Lin, D. (2017) · Composite Structures · doi:10.1016/j.compstruct.2017.08.088 · Cited by 1,270
Review of low-velocity impact properties of composite materials
Richardson, M. O. W., & Wisheart, M. (1996) · Composites Part A Applied Science and Manufacturing · doi:10.1016/1359-835x(96)00074-7 · Cited by 1,216
Three-dimensional printing of continuous-fiber composites by in-nozzle impregnation
Matsuzaki, R., Ueda, M., Namiki, M., Jeong, T.-K., Asahara, H., Horiguchi, K., Nakamura, T., Todoroki, A., & Hirano, Y. (2016) · Scientific Reports · doi:10.1038/srep23058 · Cited by 1,171
Interface and performance of 3D printed continuous carbon fiber reinforced PLA composites
Tian, X., Liu, T., Yang, C., Wang, Q., & Li, D. (2016) · Composites Part A: Applied Science and Manufacturing · doi:10.1016/j.compositesa.2016.05.032 · Cited by 1,162
Recent advances in carbon-fiber-reinforced thermoplastic composites: A review
Yao, S.-S., Jin, F., Rhee, K. Y., Hui, D., & Park, S. (2017) · Composites Part B Engineering · doi:10.1016/j.compositesb.2017.12.007 · Cited by 976
Wu, W., Geng, P., Li, G., Zhao, D., Zhang, H., & Zhao, J. (2015) · Materials · doi:10.3390/ma8095271 · Cited by 881
Dickson, A. N., Barry, J. N., McDonnell, K. A., & Dowling, D. P. (2017) · Additive Manufacturing · doi:10.1016/j.addma.2017.06.004 · Cited by 792
Lanzotti, A., Grasso, M., Staiano, G., & Martorelli, M. (2015) · Rapid Prototyping Journal · doi:10.1108/rpj-09-2014-0135 · Cited by 684
Yang, C., Tian, X., Li, D., Cao, Y., Zhao, F., & Shi, C. (2017) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2017.04.027 · Cited by 662
Measurements of the mechanical response of unidirectional 3D-printed PLA
Song, Y., Li, Y., Song, W., Yee, K., Lee, K.-Y., & Tagarielli, V. L. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.03.051 · Cited by 624
Melenka, G. W., Cheung, B. K. O., Schofield, J. S., Dawson, M. R., & Carey, J. P. (2016) · Composite Structures · doi:10.1016/j.compstruct.2016.07.018 · Cited by 597
Effect of Infill Parameters on Tensile Mechanical Behavior in Desktop 3D Printing
Fernandez-Vicente, M., Calle, W., Ferrandiz, S., & Conejero, A. (2016) · 3D Printing and Additive Manufacturing · doi:10.1089/3dp.2015.0036 · Cited by 535
3D Printing of Continuous Carbon Fibre Reinforced Thermo-Plastic (CFRTP) Tensile Test Specimens
Der Klift, F. V., Koga, Y., Todoroki, A., Ueda, M., Hirano, Y., & Matsuzaki, R. (2016) · Open Journal of Composite Materials · doi:10.4236/ojcm.2016.61003 · Cited by 516
3D printing for continuous fiber reinforced thermoplastic composites: mechanism and performance
Yang, C., Tian, X., Liu, T., Cao, Y., & Li, D. (2017) · Rapid Prototyping Journal · doi:10.1108/rpj-08-2015-0098 · Cited by 515
Characterization of 3D printed long fibre reinforced composites
Justo, J., Távara, L., García-Guzmán, L., & París, F. (2018) · Composite Structures · doi:10.1016/j.compstruct.2017.11.052 · Cited by 473
Recycling and remanufacturing of 3D printed continuous carbon fiber reinforced PLA composites
Tian, X., Liu, T., Wang, Q., Dilmurat, A., Li, D., & Ziegmann, G. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2016.11.139 · Cited by 432
Liao, G., Li, Z., Cheng, Y., Xu, D., Zhu, D., Jiang, S., Guo, J., Chen, X., Xu, G., & Zhu, Y. (2018) · Materials & Design · doi:10.1016/j.matdes.2017.11.027 · Cited by 315
Zaldivar, R. J., Witkin, D. B., McLouth, T., Patel, D. N., Schmitt, K., & Nokes, J. P. (2017) · Additive Manufacturing · doi:10.1016/j.addma.2016.11.007 · Cited by 277
Fused Deposition Technique for Continuous Fiber Reinforced Thermoplastic
Bettini, P., Alitta, G., Sala, G., & Di Landro, L. (2017) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-016-2459-8 · Cited by 226
Fused Deposition Modelling of high temperature polymers: Exploring CNT PEEK composites
Berretta, S., Davies, R., Shyng, Y. T., Wang, Y., & Ghita, O. (2017) · Polymer Testing · doi:10.1016/j.polymertesting.2017.08.024 · Cited by 218
Zhang, W., Cotton, C., Sun, J., Heider, D., Gu, B., Sun, B., & Chou, T.-W. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2017.11.018 · Cited by 203
Mechanical characterization of 3D printed polymers for fiber reinforced polymers processing
Türk, D.-A., Brenni, F., Zogg, M., & Meboldt, M. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.01.050 · Cited by 168
State-of-the-art of fiber-reinforced polymers in additive manufacturing technologies
Hofstätter, T., Pedersen, D. B., Tosello, G., & Hansen, H. N. (2017) · Journal of Reinforced Plastics and Composites · doi:10.1177/0731684417695648 · Cited by 152
3D printing of carbon fibre-reinforced plastic parts
Nakagawa, Y., Mori, K., & Maeno, T. (2017) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-016-9891-7 · Cited by 150
Smojver, I., & Ivančević, D. (2010) · Composites Science and Technology · doi:10.1016/j.compscitech.2010.12.024 · Cited by 118
On the response of two commercially-important CFRP structures to multiple ice impacts
Appleby-Thomas, G. J., Hazell, P. J., & Dahini, G. (2011) · Composite Structures · doi:10.1016/j.compstruct.2011.04.029 · Cited by 94
Cited by
An Overview on 3D Printing Technology: Technological, Materials, and Applications
Shahrubudin, N., Lee, T. C., & Ramlan, R. (2019) · Procedia Manufacturing · doi:10.1016/j.promfg.2019.06.089 · Cited by 2,050
Wickramasinghe, S., Do, T., & Tran, P. (2020) · Polymers · doi:10.3390/polym12071529 · Cited by 1,052
Recent Progress on Polymer Materials for Additive Manufacturing
Tan, L. J., Zhu, W., & Zhou, K. (2020) · Advanced Functional Materials · doi:10.1002/adfm.202003062 · Cited by 740
Kabir, S. M. F., Mathur, K., & Seyam, A.-F. M. (2020) · Composite Structures · doi:10.1016/j.compstruct.2019.111476 · Cited by 678
Recent Progress in Additive Manufacturing of Fiber Reinforced Polymer Composite
Goh, G. D., Yap, Y. L., Agarwala, S., & Yeong, W. Y. (2019) · Advanced Materials Technologies · doi:10.1002/admt.201800271 · Cited by 621
Metadata
- Authors
- Caminero, M. A., Chacón, J. M., García-Moreno, I., & Rodríguez, G. P.
- Venue
- Composites Part B: Engineering
- Publisher
- Elsevier BV
- Published
- 2018-09
- Volume
- 148
- Pages
- 93-103
- ISSN
- 1359-8368 (ISSN-L)
- OpenAlex
- W2801434627
- Cited by
- 479
- References
- 30
- FWCI
- 22.20
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.