The DOI matches its Crossref record; 106 of the 106 references it cites were found in a registry or an index.
Drying shrinkage in alkali-activated binders – A critical review
Abstract
Abstract Alkali-activated binders have been proposed and have emerged as an alternative to ordinary Portland cement (OPC) binders with acceptable mechanical and durability performances in addition to positive environmental impacts. These alternative binders use a wide range of aluminosilicate precursors, with differing availabilities, reactivities, costs and CO2 emissions. Despite all the studies published on improving the characteristics of these materials in the last decades, some aspects of alkali-activated binders require further investigations. For instance, shrinkage in alkali-activated binders due to the different chemical processes being involved is more complicated than OPC composites and it plays a key role in long-term performance. However, information on the shrinkage behavior of these binder systems is scattered and fragmented. Therefore, this review critically surveys the drying shrinkage behavior of alkali-activated binders with slag, fly ash and metakaolin. The mechanisms of the drying shrinkage and the factors that affect shrinkage are discussed. Different solutions to limit the shrinkage are also presented. Then, an analysis is conducted based on the literature, and the main chemical elements affecting the drying shrinkage of alkali-activated materials are proposed. Finally, the feasibility of using the developed empirical models for predicting the drying shrinkage of OPC concretes is also investigated for alkali activated binders. This review shows that alkali-activated slag binders generally have the higher rate of the drying shrinkage compared to other alkali activated binders, albeit, reinforcing the plain compositions with fibers, using expanding admixtures, curing at elevated temperatures, using a combination of slag with fly ash or metakaolin reduces successfully the drying shrinkage. Moreover, utilizing ternary diagrams, it is revealed that the molar ratio of Ca/Si has the greatest impact on the rate of drying shrinkage in the alkali-activated binders.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Geopolymer technology: The current state of the art
Duxson, P., Fernández-Jiménez, A., Provis, J. L., Lukey, G. C., Palomo, A., & van Deventer, J. S. J. (2007) · Journal of Materials Science · doi:10.1007/s10853-006-0637-z · Cited by 4,742
Palomo, A., Grutzeck, M. W., & Blanco, M. T. (1999) · Cement and Concrete Research · doi:10.1016/s0008-8846(98)00243-9 · Cited by 2,319
Provis, J. L. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2017.02.009 · Cited by 2,272
The role of inorganic polymer technology in the development of ‘green concrete’
Duxson, P., Provis, J. L., Lukey, G. C., & van Deventer, J. S. J. (2007) · Cement and Concrete Research · doi:10.1016/j.cemconres.2007.08.018 · Cited by 1,998
Costs and carbon emissions for geopolymer pastes in comparison to ordinary portland cement
McLellan, B. C., Williams, R. P., Lay, J., van Riessen, A., & Corder, G. D. (2011) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2011.02.010 · Cited by 1,949
Advances in alternative cementitious binders
Juenger, M. C. G., Winnefeld, F., Provis, J. L., & Ideker, J. H. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2010.11.012 · Cited by 1,851
Duxson, P., Provis, J. L., Lukey, G. C., Mallicoat, S. W., Kriven, W. M., & van Deventer, J. S. J. (2005) · Colloids and Surfaces A: Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2005.06.060 · Cited by 1,807
One-part alkali-activated materials: A review
Luukkonen, T., Abdollahnejad, Z., Yliniemi, J., Kinnunen, P., & Illikainen, M. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2017.10.001 · Cited by 1,456
Ismail, I., Bernal, S. A., Provis, J. L., San Nicolas, R., Hamdan, S., & van Deventer, J. S. J. (2014) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2013.09.006 · Cited by 1,317
Yip, C. K., Lukey, G. C., & van Deventer, J. S. J. (2005) · Cement and Concrete Research · doi:10.1016/j.cemconres.2004.10.042 · Cited by 1,274
Composition and microstructure of alkali activated fly ash binder: Effect of the activator
Fernández-Jiménez, A., & Palomo, A. (2005) · Cement and Concrete Research · doi:10.1016/j.cemconres.2005.03.003 · Cited by 1,144
Bernal, S. A., Provis, J. L., Walkley, B., San Nicolas, R., Gehman, J. D., Brice, D. G., Kilcullen, A. R., Duxson, P., & van Deventer, J. S. J. (2013) · Cement and Concrete Research · doi:10.1016/j.cemconres.2013.06.007 · Cited by 1,019
Alkali-activated binders: A review
Pacheco-Torgal, F., Castro-Gomes, J., & Jalali, S. (2008) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2007.10.015 · Cited by 989
Alkali-activated fly ash/slag cements
Puertas, F., Martı́nez-Ramı́rez, S., Alonso, S., & Vázquez, T. (2000) · Cement and Concrete Research · doi:10.1016/s0008-8846(00)00298-2 · Cited by 921
Alkali Activated Materials: State-of-the-Art Report, RILEM TC 224-AAM
(2014) · RILEM State-of-the-Art Reports · doi:10.1007/978-94-007-7672-2 · Cited by 906
Assessment of CO2 reduction of alkali-activated concrete
Yang, K.-H., Song, J.-K., & Song, K.-I. (2013) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2012.08.001 · Cited by 832
Technical and commercial progress in the adoption of geopolymer cement
Van Deventer, J. S. J., Provis, J. L., & Duxson, P. (2012) · Minerals Engineering · doi:10.1016/j.mineng.2011.09.009 · Cited by 820
Durability of geopolymer materials in sodium and magnesium sulfate solutions
Bakharev, T. (2005) · Cement and Concrete Research · doi:10.1016/j.cemconres.2004.09.002 · Cited by 783
Lee, N. K., & Lee, H. K. (2013) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2013.05.107 · Cited by 754
Effect of pore size distribution on drying shrinking of alkali-activated slag concrete
Collins, F., & Sanjayan, J. G. (2000) · Cement and Concrete Research · doi:10.1016/s0008-8846(00)00327-6 · Cited by 720
Characterisation of fly ashes. Potential reactivity as alkaline cements☆
Fernández-Jiménez, A., & Palomo, A. (2003) · Fuel · doi:10.1016/s0016-2361(03)00194-7 · Cited by 690
Designing Precursors for Geopolymer Cements
Duxson, P., & Provis, J. L. (2008) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2008.02787.x · Cited by 662
Influence of activator on the strength and drying shrinkage of alkali-activated slag mortar
Duran Atiş, C., Bilim, C., Çelik, Ö., & Karahan, O. (2009) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2007.10.011 · Cited by 658
(Micro)-structural comparison between geopolymers, alkali-activated slag cement and Portland cement
Lecomte, I., Henrist, C., Liégeois, M., Maseri, F., Rulmont, A., & Cloots, R. (2006) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2005.12.021 · Cited by 597
The role played by the reactive alumina content in the alkaline activation of fly ashes
Fernández-Jiménez, A., Palomo, A., Sobrados, I., & Sanz, J. (2006) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2005.11.015 · Cited by 590
Drying and autogenous shrinkage of pastes and mortars with activated slag cement
Melo Neto, A. A., Cincotto, M. A., & Repette, W. (2008) · Cement and Concrete Research · doi:10.1016/j.cemconres.2007.11.002 · Cited by 578
Structure and properties of clay-based geopolymer cements: A review
Liew, Y.-M., Heah, C.-Y., Mohd Mustafa, A. B., & Kamarudin, H. (2016) · Progress in Materials Science · doi:10.1016/j.pmatsci.2016.08.002 · Cited by 574
Chindaprasirt, P., De Silva, P., Sagoe-Crentsil, K., & Hanjitsuwan, S. (2012) · Journal of Materials Science · doi:10.1007/s10853-012-6353-y · Cited by 539
Effect of binder content on the performance of alkali-activated slag concretes
Bernal, S. A., Mejía de Gutiérrez, R., Pedraza, A. L., Provis, J. L., Rodriguez, E. D., & Delvasto, S. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2010.08.017 · Cited by 537
Engineering properties of inorganic polymer concretes (IPCs)
Sofi, M., van Deventer, J. S. J., Mendis, P. A., & Lukey, G. C. (2007) · Cement and Concrete Research · doi:10.1016/j.cemconres.2006.10.008 · Cited by 522
A review on alkaline activation: New analytical perspectives
Palomo, A., Krivenko, P., Garcia-Lodeiro, I., Kavalerova, E., Maltseva, O., & Fernández-Jiménez, A. (2014) · Materiales de Construcción · doi:10.3989/mc.2014.00314 · Cited by 501
29Si NMR Study of Structural Ordering in Aluminosilicate Geopolymer Gels
Duxson, P., Provis, J. L., Lukey, G. C., Separovic, F., & van Deventer, J. S. J. (2005) · Langmuir · doi:10.1021/la047336x · Cited by 479
Engineering Properties of Alkali-Activated Fly Ash Concrete
(2006) · ACI Materials Journal · doi:10.14359/15261 · Cited by 476
Shrinkage mechanisms of alkali-activated slag
Ye, H., & Radlińska, A. (2016) · Cement and Concrete Research · doi:10.1016/j.cemconres.2016.07.001 · Cited by 469
Weng, L., & Sagoe-Crentsil, K. (2007) · Journal of Materials Science · doi:10.1007/s10853-006-0820-2 · Cited by 467
Shrinkage characteristics of alkali-activated fly ash/slag paste and mortar at early ages
Lee, N. K., Jang, J. G., & Lee, H. K. (2014) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2014.07.007 · Cited by 462
Effects of dosage and modulus of water glass on early hydration of alkali–slag cements
Krizan, D., & Zivanovic, B. (2002) · Cement and Concrete Research · doi:10.1016/s0008-8846(01)00717-7 · Cited by 444
Hanjitsuwan, S., Hunpratub, S., Thongbai, P., Maensiri, S., Sata, V., & Chindaprasirt, P. (2014) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2013.09.012 · Cited by 437
Design Provisions for Drying Shrinkage and Creep of Normal-Strength Concrete
Gardner, N. J., & Lockman, M. J. (2001) · ACI Materials Journal · doi:10.14359/10199 · Cited by 433
Nematollahi, B., Sanjayan, J., & Shaikh, F. U. A. (2015) · Ceramics International · doi:10.1016/j.ceramint.2014.12.154 · Cited by 426
Influence of key parameters on drying shrinkage of cementitious materials
Bissonnette, B., Pierre, P., & Pigeon, M. (1999) · Cement and Concrete Research · doi:10.1016/s0008-8846(99)00156-8 · Cited by 422
Mechanisms of interfacial bond in steel and polypropylene fiber reinforced geopolymer composites
Ranjbar, N., Talebian, S., Mehrali, M., Kuenzel, C., Metselaar, H. S. C., & Jumaat, M. Z. (2015) · Composites Science and Technology · doi:10.1016/j.compscitech.2015.11.009 · Cited by 390
Variation in hybrid cements over time. Alkaline activation of fly ash–portland cement blends
García-Lodeiro, I., Fernández-Jiménez, A., & Palomo, A. (2013) · Cement and Concrete Research · doi:10.1016/j.cemconres.2013.03.022 · Cited by 385
Palacios, M., & Puertas, F. (2007) · Cement and Concrete Research · doi:10.1016/j.cemconres.2006.11.021 · Cited by 362
Effect of elevated temperature curing on properties of alkali-activated slag concrete
Bakharev, T., Sanjayan, J. G., & Cheng, Y.-B. (1999) · Cement and Concrete Research · doi:10.1016/s0008-8846(99)00143-x · Cited by 349
Atiş, C. D., Görür, E. B., Karahan, O., Bilim, C., İlkentapar, S., & Luga, E. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2015.08.089 · Cited by 329
Jin, F., Gu, K., & Al-Tabbaa, A. (2015) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2014.10.007 · Cited by 325
Properties of cementless mortars activated by sodium silicate
Yang, K.-H., Song, J.-K., Ashour, A. F., & Lee, E.-T. (2008) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2007.07.003 · Cited by 319
High-Strength Geopolymer Using Fine High-Calcium Fly Ash
Chindaprasirt, P., Chareerat, T., Hatanaka, S., & Cao, T. (2010) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0000161 · Cited by 319
Fresh and hardened properties of alkali-activated fly ash/slag pastes with superplasticizers
Jang, J. G., Lee, N. K., & Lee, H. K. (2014) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2013.09.048 · Cited by 318
Microcracking and strength development of alkali activated slag concrete
Collins, F., & Sanjayan, J. G. (2001) · Cement and Concrete Composites · doi:10.1016/s0958-9465(01)00003-8 · Cited by 316
Mechanical and microstructural properties of heat cured alkali-activated slag mortars
Aydın, S., & Baradan, B. (2011) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2011.10.005 · Cited by 305
Free, restrained and drying shrinkage of cement mortar composites reinforced with vegetable fibres
Toledo Filho, R. D., Ghavami, K., Sanjuán, M. A., & England, G. L. (2005) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2004.09.005 · Cited by 299
Ambient Temperature Drying Shrinkage and Cracking in Metakaolin‐Based Geopolymers
Kuenzel, C., Vandeperre, L. J., Donatello, S., Boccaccini, A. R., & Cheeseman, C. (2012) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2012.05380.x · Cited by 291
Understanding the drying shrinkage performance of alkali-activated slag mortars
Ye, H., Cartwright, C., Rajabipour, F., & Radlińska, A. (2017) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2016.11.010 · Cited by 287
The shrinkage of alkali activated fly ash
Ma, Y., & Ye, G. (2015) · Cement and Concrete Research · doi:10.1016/j.cemconres.2014.10.024 · Cited by 275
Effects of nano-TiO2 on strength, shrinkage and microstructure of alkali activated slag pastes
Yang, L. Y., Jia, Z. J., Zhang, Y. M., & Dai, J. G. (2015) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2014.11.009 · Cited by 267
Marjanović, N., Komljenović, M., Baščarević, Z., Nikolić, V., & Petrović, R. (2015) · Ceramics International · doi:10.1016/j.ceramint.2014.09.075 · Cited by 266
Yang, T., Zhu, H., & Zhang, Z. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.05.067 · Cited by 266
Cracking risks associated with early age shrinkage
Holt, E., & Leivo, M. (2003) · Cement and Concrete Composites · doi:10.1016/s0958-9465(03)00068-4 · Cited by 253
Duan, P., Yan, C., Luo, W., & Zhou, W. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2015.12.095 · Cited by 252
Thomas, R. J., Lezama, D., & Peethamparan, S. (2017) · Cement and Concrete Research · doi:10.1016/j.cemconres.2016.10.003 · Cited by 251
Effect of chemical admixtures on properties of high-calcium fly ash geopolymer
Rattanasak, U., Pankhet, K., & Chindaprasirt, P. (2011) · International Journal of Minerals, Metallurgy, and Materials · doi:10.1007/s12613-011-0448-3 · Cited by 247
Thermal Activation of Albite for the Synthesis of One‐Part Mix Geopolymers
Feng, D., Provis, J. L., & van Deventer, J. S. J. (2012) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2011.04925.x · Cited by 244
Arbi, K., Nedeljković, M., Zuo, Y., & Ye, G. (2016) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.6b00559 · Cited by 244
Carbonate mineral addition to metakaolin-based geopolymers
Yip, C. K., Provis, J. L., Lukey, G. C., & van Deventer, J. S. J. (2008) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2008.07.004 · Cited by 232
Nematollahi, B., Sanjayan, J., Qiu, J., & Yang, E.-H. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.11.117 · Cited by 223
Shrinkage and strength development of alkali-activated fly ash-slag binary cements
Hojati, M., & Radlińska, A. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.06.040 · Cited by 217
The suitability of thermally activated illite/smectite clay as raw material for geopolymer binders
Buchwald, A., Hohmann, M., Posern, K., & Brendler, E. (2009) · Applied Clay Science · doi:10.1016/j.clay.2009.08.026 · Cited by 215
Prediction of the shrinkage behavior of recycled aggregate concrete: A review
Silva, R. V., de Brito, J., & Dhir, R. K. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2014.12.102 · Cited by 203
Compressive strength and degree of reaction of biomass- and fly ash-based geopolymer
Songpiriyakij, S., Kubprasit, T., Jaturapitakkul, C., & Chindaprasirt, P. (2010) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2009.09.002 · Cited by 203
New Cementitious Materials Based on Alkali‐Activated Fly Ash: Performance at High Temperatures
Fernández‐Jiménez, A., Palomo, A., Pastor, J. Y., & Martín, A. (2008) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2008.02625.x · Cited by 199
Characterisation of One-Part Geopolymer Binders Made from Fly Ash
Hajimohammadi, A., & van Deventer, J. S. J. (2017) · Waste and Biomass Valorization · doi:10.1007/s12649-016-9582-5 · Cited by 192
Nematollahi, B., Sanjayan, J., Qiu, J., & Yang, E.-H. (2017) · Archives of Civil and Mechanical Engineering · doi:10.1016/j.acme.2016.12.005 · Cited by 187
Life-cycle analysis of geopolymers
Weil, M., Dombrowski, K., & Buchwald, A. (2009) · Geopolymers · doi:10.1533/9781845696382.2.194 · Cited by 185
Mobili, A., Belli, A., Giosuè, C., Bellezze, T., & Tittarelli, F. (2016) · Cement and Concrete Research · doi:10.1016/j.cemconres.2016.07.004 · Cited by 175
Composition design and performance of alkali-activated cements
Li, N., Shi, C., Wang, Q., Zhang, Z., & Ou, Z. (2017) · Materials and Structures · doi:10.1617/s11527-017-1048-0 · Cited by 169
Gao, X., Yu, Q., & Brouwers, H. J. H. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.05.026 · Cited by 167
Manufacture of hybrid cements with fly ash and bottom ash from a municipal solid waste incinerator
García-Lodeiro, I., Taboada, V. C., Fernández‐Jiménez, A., & Palomo, A. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2015.12.079 · Cited by 165
Zhang, Z., Li, L., Ma, X., & Wang, H. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.03.043 · Cited by 164
Zhang, W., Hama, Y., & Na, S. H. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2015.05.103 · Cited by 162
Yang, K., & Song, J. (2009) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)0899-1561(2009)21:3(119 · Cited by 159
Alkali-activated fly ash-based geopolymers with zeolite or bentonite as additives
Hu, M., Zhu, X., & Long, F. (2009) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2009.07.006 · Cited by 158
Yao, X., Yang, T., & Zhang, Z. (2015) · Materials and Structures · doi:10.1617/s11527-015-0694-3 · Cited by 147
Jia, Z., Yang, Y., Yang, L., Zhang, Y., & Sun, Z. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.09.162 · Cited by 142
Allahverdi, A., & Škvára, F. (2005) · Cited by 139
Distinctive microstructural features of aged sodium silicate-activated slag concretes
Nicolas, R. S., Bernal, S. A., de Gutiérrez, R. M., van Deventer, J. S. J., & Provis, J. L. (2014) · Cement and Concrete Research · doi:10.1016/j.cemconres.2014.07.008 · Cited by 130
Yazeli, H. T., Behfarnia, K., & Khalili, M. (2018) · Journal of Advanced Concrete Technology · doi:10.3151/jact.16.293 · Cited by 125
Magnesia modification of alkali-activated slag fly ash cement
Shen, W., Wang, Y., Zhang, T., Zhou, M., Li, J., & Cui, X. (2011) · Journal of Wuhan University of Technology-Mater Sci Ed · doi:10.1007/s11595-011-0182-8 · Cited by 112
Clay reactivity: Production of alkali activated cements
Ruiz-Santaquiteria, C., Fernández‐Jiménez, A., Skibsted, J., & Palomo, A. (2013) · Applied Clay Science · doi:10.1016/j.clay.2012.10.012 · Cited by 104
Strength and Drying Shrinkage of Alkali-Activated Slag Paste and Mortar
Chi, M., Chang, J., & Huang, R. (2012) · Advances in Civil Engineering · doi:10.1155/2012/579732 · Cited by 103
Samson, G., Cyr, M., & Gao, X. X. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.03.160 · Cited by 102
Evaluation of hybrid steel fiber reinforcement in high performance geopolymer composites
Gao, X., Yu, Q., Yu, R., & Brouwers, H. J. H. (2017) · Materials and Structures · doi:10.1617/s11527-017-1030-x · Cited by 99
Seiffarth, T., Hohmann, M., Posern, K., & Kaps, C. (2012) · Applied Clay Science · doi:10.1016/j.clay.2012.09.010 · Cited by 90
Accelerated ageing of geopolymers
Lloyd, R. R. (2009) · Elsevier eBooks · doi:10.1533/9781845696382.2.139 · Cited by 87
Preparation of drying powder inorganic polymer cement based on alkali-activated slag technology
Wang, K.-T., Du, L.-Q., Lv, X., He, Y., & Cui, X. (2017) · Powder Technology · doi:10.1016/j.powtec.2017.02.036 · Cited by 85
Chi, M. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2015.09.029 · Cited by 84
Carbonation-induced volume change in alkali-activated slag
Ye, H., & Radlińska, A. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.03.238 · Cited by 69
Provis, J. L. (2013) · RILEM state-of-the-art reports · doi:10.1007/978-94-007-7672-2_1 · Cited by 51
Compressive strength, microstructure and hydration products of hybrid alkaline cements
Abdollahnejad, Z., Hlavacek, P., Miraldo, S., Pacheco-Torgal, F., & de Aguiar, J. L. B. (2014) · Materials Research · doi:10.1590/s1516-14392014005000091 · Cited by 47
Yoo, D., Park, J.-J., Kim, S. W., et al. (2013) · Journal of Composite Materials · doi:10.1177/0021998313493809 · Cited by 44
Mineralization dynamics of metakaolin-based alkali-activated cements
Gevaudan, J. P., Campbell, K. M., Kane, T. J., Shoemaker, R. L., & Srubar, W. V. (2017) · Cement and Concrete Research · doi:10.1016/j.cemconres.2017.01.001 · Cited by 44
Khorasanipour, M. (2015) · Journal of Geochemical Exploration · doi:10.1016/j.gexplo.2015.03.001 · Cited by 37
Cements with a low clinker content: versatile use of raw materials
García-Lodeiro, I., Fernández‐Jiménez, A., & Palomo, A. (2015) · Journal of Sustainable Cement-Based Materials · doi:10.1080/21650373.2015.1040865 · Cited by 36
Characterisation of the Sarcheshmeh copper mine tailings, Kerman province, southeast of Iran
Malakooti, S. J., Tonkaboni, S. Z. S., Noaparast, M., Ardejani, F. D., & Naseh, R. (2013) · Environmental Earth Sciences · doi:10.1007/s12665-013-2630-6 · Cited by 27
Specific Examples of Hybrid Alkaline Cement
Fernández‐Jiménez, A., García-Lodeiro, I., Donatello, S., Maltseva, O., & Palomo, A. (2014) · MATEC Web of Conferences · doi:10.1051/matecconf/20141101001 · Cited by 20
Cited by
Recent progress in low-carbon binders
Shi, C., Qu, B., & Provis, J. L. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2019.05.009 · Cited by 714
Advances in geopolymer materials: A comprehensive review
Cong, P., & Cheng, Y. (2021) · Journal of Traffic and Transportation Engineering (English Edition) · doi:10.1016/j.jtte.2021.03.004 · Cited by 481
Zhang, C., Khorshidi, H., Najafi, E., & Ghasemi, M. (2023) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2022.135390 · Cited by 300
Zhang, B., Zhu, H., Cheng, Y., Huseien, G. F., & Shah, K. W. (2022) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2021.125993 · Cited by 258
Preparation and Reaction Mechanism Characterization of Alkali-activated Coal Gangue–Slag Materials
Ma, H., Zhu, H., Yi, C., Fan, J., Chen, H., Xu, X., & Wang, T. (2019) · Materials · doi:10.3390/ma12142250 · Cited by 91
Metadata
- Authors
- Mastali, M., Kinnunen, P., Dalvand, A., Mohammadi Firouz, R., & Illikainen, M.
- Venue
- Construction and Building Materials
- Publisher
- Elsevier BV
- Published
- 2018-11
- Volume
- 190
- Pages
- 533-550
- ISSN
- 0950-0618 (ISSN-L)
- OpenAlex
- W2892995733
- Cited by
- 468
- References
- 106
- FWCI
- 27.62
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.