The DOI matches its Crossref record; 6 of the 6 references it cites were found in a registry or an index.
3D printing of polyether-ether-ketone for biomedical applications
Abstract
Abstract Despite the rapid progress of several three-dimensional (3D) printing technologies, there exists a critical barrier in-term of processability of high performance materials. Polyether-ether-ketone (PEEK) is known for its higher mechanical properties, chemical stability, biological stability and biocompatibility suitable for certain biomedical applications. Examining a growing body of scientific literature on 3D printing of biomedical polymers indicates that most of the studies are conducted using biomedical polymers such as poly-carpolactone, poly-lactic acid, poly-glycolic acid, polyethylene and polyurethanes. However, studies on 3D Printing of PEEK is sparse owing to the higher temperatures needed for melting, lacking of availability of suitable feedstock, concerns over poor adhesion between layers, and time consuming and uneconomical processing steps. Given the unique nature of PEEK class of polymers, this manuscript closely examines 3D printability of PEEK for a range of biomedical applications. This manuscript also presents ideas, feasible solutions and enabling scientific mechanisms to improve the 3D printability of PEEK. This article will help the research community to strengthen the conceptual knowledge and insights on the 3D printing of PEEK based medical devices and tools, and future possibilities.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
Rapid casting of patterned vascular networks for perfusable engineered three-dimensional tissues
Miller, J. S., Stevens, K. R., Yang, M. T., Baker, B. M., Nguyen, D.-H. T., Cohen, D. M., Toro, E., Chen, A. A., Galie, P. A., Yu, X., et al. (2012) · Nature Materials · doi:10.1038/nmat3357 · Cited by 1,917
Yang, C., Tian, X., Li, D., Cao, Y., Zhao, F., & Shi, C. (2017) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2017.04.027 · Cited by 662
Effects of extrusion speed and printing speed on the 3D printing stability of extruded PEEK filament
Geng, P., Zhao, J., Wu, W., Ye, W., Wang, Y., Wang, S., & Zhang, S. (2019) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2018.11.023 · Cited by 321
Additive layer manufacturing of poly (ether ether ketone) via FDM
Rinaldi, M., Ghidini, T., Cecchini, F., Brandao, A., & Nanni, F. (2018) · Composites Part B Engineering · doi:10.1016/j.compositesb.2018.03.029 · Cited by 301
Lee, K.-W., Wang, S., Fox, B. C., Ritman, E. L., Yaszemski, M. J., & Lu, L. (2007) · Biomacromolecules · doi:10.1021/bm060834v · Cited by 292
Cited by
3D printing of hydrogels: Rational design strategies and emerging biomedical applications
Li, J., Wu, C., Chu, P. K., & Gelinsky, M. (2020) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2020.100543 · Cited by 862
Current status and future directions of fused filament fabrication
Singh, S., Singh, G., Prakash, C., & Ramakrishna, S. (2020) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2020.04.049 · Cited by 385
Self-citation3D printing technology; methods, biomedical applications, future opportunities and trends
Bozkurt, Y., & Karayel, E. (2021) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2021.07.050 · Cited by 384
Recent advances of additive manufacturing in implant fabrication – A review
Mobarak, M. H., Islam, M. A., Hossain, N., Al Mahmud, M. Z., Rayhan, M. T., Nishi, N. J., & Chowdhury, M. A. (2023) · Applied Surface Science Advances · doi:10.1016/j.apsadv.2023.100462 · Cited by 307
Doshi, M., Mahale, A., Kumar Singh, S., & Deshmukh, S. (2022) · Materials Today: Proceedings · doi:10.1016/j.matpr.2021.10.003 · Cited by 256
Metadata
- Authors
- Singh, S., Prakash, C., & Ramakrishna, S.
- Venue
- European Polymer Journal
- Publisher
- Elsevier BV
- Published
- 2019-05
- Volume
- 114
- Pages
- 234-248
- ISSN
- 0014-3057 (ISSN-L)
- OpenAlex
- W2915478645
- Cited by
- 220
- References
- 6
- FWCI
- 13.05
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: 3D printing of polyether-ether-ketone for biomedical applications. https://app.cochat.ai/papers/10.1016/j.eurpolymj.2019.02.035
- The paper
- Singh, S., Prakash, C., & Ramakrishna, S. (2019). 3D printing of polyether-ether-ketone for biomedical applications. European Polymer Journal. https://doi.org/10.1016/j.eurpolymj.2019.02.035
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.