The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Significance of hot isostatic pressing (HIP) on multiaxial deformation and fatigue behaviors of additive manufactured Ti-6Al-4V including build orientation and surface roughness effects
Open accessAbstract
Abstract Additive manufacturing (AM) technology has gained significant attention in recent years due to several important advantages. However, design of critical load carrying parts using this technique is still at its infancy, partly due to the inferior performance and lack of sufficient understanding of cyclic deformation and fatigue behaviors of AM metals as compared to their wrought counterparts. Similar to most other components in different industries, AM parts typically undergo cyclic loadings through their service life; therefore, fatigue performance is a key performance criterion. In addition, due to common presence of multiaxial stress states at fatigue critical locations, multiaxial fatigue is of special interest. In this study, thin-walled tubular specimens made of Ti-6Al-4V alloy fabricated with powder bed fusion (PBF) process were used to investigate their cyclic deformation and fatigue behaviors. The main focus of this study was on the effect of hot isostatic pressing (HIP) on fatigue performance under uniaxial, torsion, combined in-phase, and 90° out-of-phase axial-torsion loads. To study build orientation effect, both vertically built and diagonally built (at 45°) specimens were included. However, no substantial difference on the fatigue behavior of vertical and 45° built specimens was observed. Although the majority of specimens had a machined surface, some torsional tests with as-built surface were also included to evaluate surface roughness effect. It was found that even after HIP treatment, the rough surface is the dominant factor in shortening the fatigue life. In addition, to evaluate the effectiveness of the HIP treatment, torsion fatigue performance of the HIPed specimens were compared to torsion fatigue performance of annealed AM specimens, as well as to the multiaxial fatigue behavior of the conventional wrought material. Fatigue failure mechanism of the HIPed material was shear, similar to the wrought material, and fatigue performance was found to be similar to the wrought alloy. Fatigue test results were correlated well using a shear-based critical plane parameter approach, also similar to the wrought material. Comparison of multiaxial fatigue data in this study and a similar previous study by the authors indicates that fabrication machine-to-machine and the associated build parameter differences can result in substantial differences in the observed defect size and population, resulting in different failure mechanisms and subsequently different fatigue performance.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984
Cited by
Sanaei, N., & Fatemi, A. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100724 · Cited by 1,029
Self-citationProgress and perspectives in laser additive manufacturing of key aeroengine materials
Tan, C., Weng, F., Sui, S., Chew, Y., & Bi, G. (2021) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2021.103804 · Cited by 520
Defects and anomalies in powder bed fusion metal additive manufacturing
Mostafaei, A., Zhao, C., He, Y., Reza Ghiaasiaan, S., Shi, B., Shao, S., Shamsaei, N., Wu, Z., Kouraytem, N., Sun, T., et al. (2022) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2021.100974 · Cited by 491
Defect characteristics and analysis of their variability in metal L-PBF additive manufacturing
Sanaei, N., Fatemi, A., & Phan, N. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.108091 · Cited by 301
Self-citationMolaei, R., Fatemi, A., Sanaei, N., Pegues, J., Shamsaei, N., Shao, S., Li, P., Warner, D. H., & Phan, N. (2020) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2019.105363 · Cited by 264
Self-citation
Metadata
- Authors
- Molaei, R., Fatemi, A., & Phan, N.
- Venue
- International Journal of Fatigue
- Publisher
- Elsevier BV
- Published
- 2018-12
- Volume
- 117
- Pages
- 352-370
- ISSN
- 0142-1123 (ISSN-L)
- OpenAlex
- W2883558878
- Cited by
- 191
- References
- 1
- FWCI
- 12.15
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Significance of hot isostatic pressing (HIP) on multiaxial deformation and fatigue behaviors of additive manufactured Ti-6Al-4V including build orientation and surface roughness effects. https://app.cochat.ai/papers/10.1016/j.ijfatigue.2018.07.035
- The paper
- Molaei, R., Fatemi, A., & Phan, N. (2018). Significance of hot isostatic pressing (HIP) on multiaxial deformation and fatigue behaviors of additive manufactured Ti-6Al-4V including build orientation and surface roughness effects. International Journal of Fatigue. https://doi.org/10.1016/j.ijfatigue.2018.07.035
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.