The DOI matches its Crossref record; 44 of the 44 references it cites were found in a registry or an index.
Properties and characterization of green one-part geopolymer activated by composite activators
Abstract
Abstract One-part geopolymer similar to conventional Portland cement by just adding water is a new type of green cementitious material. Na2SiO3-anhydrous is an excellent powder activator for preparing one-part geopolymer, but its CO2-e emission and alkalinity are very high. In this study, the Na2CO3 was used to replace a portion of Na2SiO3-anhydrous, and the properties of one-part geopolymer with composite activators were investigated systematically. The possible influencing mechanism of the complex use of activators in one-part geopolymer was proposed. Test results indicate that the replacement level of Na2CO3 has slight impact on the fluidity and increases the final setting time significantly. This is directly related to the initial heat release rate and the type of network structures formed. The compressive strength decreases with increasing the Na2CO3 content. On the one hand, the quantity of gelatinous products reduces and calcite is produced as the new phase after replacing Na2SiO3-anhydrous by Na2CO3. On the other hand, the gathering of calcite and low-crystalline CaCO3 in some regions leads to the generation of many large micro-cracks, which explains the change in the porosity of the unfavorable pores. Judged from the cost per MPa and total CO2-e emission for a cubic meter of cementitious materials, one-part geopolymer activated by composite activators is cleaner than that activated by single Na2SiO3-anhydrous or Na2CO3. This study provides a guidance for preparing one-part geopolymer with lower alkalinity and potential environmental impact.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Carbon dioxide equivalent (CO2-e) emissions: A comparison between geopolymer and OPC cement concrete
Turner, L. K., & Collins, F. G. (2013) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2013.01.023 · Cited by 2,411
The role of inorganic polymer technology in the development of ‘green concrete’
Duxson, P., Provis, J. L., Lukey, G. C., & van Deventer, J. S. J. (2007) · Cement and Concrete Research · doi:10.1016/j.cemconres.2007.08.018 · Cited by 1,998
Costs and carbon emissions for geopolymer pastes in comparison to ordinary portland cement
McLellan, B. C., Williams, R. P., Lay, J., van Riessen, A., & Corder, G. D. (2011) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2011.02.010 · Cited by 1,949
Advances in alternative cementitious binders
Juenger, M. C. G., Winnefeld, F., Provis, J. L., & Ideker, J. H. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2010.11.012 · Cited by 1,851
One-part alkali-activated materials: A review
Luukkonen, T., Abdollahnejad, Z., Yliniemi, J., Kinnunen, P., & Illikainen, M. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2017.10.001 · Cited by 1,456
Habert, G., d’Espinose de Lacaillerie, J. B., & Roussel, N. (2011) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2011.03.012 · Cited by 1,407
Ismail, I., Bernal, S. A., Provis, J. L., San Nicolas, R., Hamdan, S., & van Deventer, J. S. J. (2014) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2013.09.006 · Cited by 1,317
Yip, C. K., Lukey, G. C., & van Deventer, J. S. J. (2005) · Cement and Concrete Research · doi:10.1016/j.cemconres.2004.10.042 · Cited by 1,274
Barbosa, V. F. F., MacKenzie, K. J. D., & Thaumaturgo, C. (2000) · International Journal of Inorganic Materials · doi:10.1016/s1466-6049(00)00041-6 · Cited by 1,128
Ben Haha, M., Le Saout, G., Winnefeld, F., & Lothenbach, B. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2010.11.016 · Cited by 1,059
Fly ash-based geopolymer: clean production, properties and applications
Zhuang, X. Y., Chen, L., Komarneni, S., Zhou, C. H., Tong, D. S., Yang, H. M., Yu, W. H., & Wang, H. (2016) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2016.03.019 · Cited by 1,020
A review on emission analysis in cement industries
Ali, M. B., Saidur, R., & Hossain, M. S. (2011) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2011.02.014 · Cited by 941
Alkali-activated fly ash/slag cements
Puertas, F., Martı́nez-Ramı́rez, S., Alonso, S., & Vázquez, T. (2000) · Cement and Concrete Research · doi:10.1016/s0008-8846(00)00298-2 · Cited by 921
Haha, M. B., Lothenbach, B., Le Saout, G., & Winnefeld, F. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.05.002 · Cited by 914
Hemalatha, T., & Ramaswamy, A. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.01.114 · Cited by 800
(Micro)-structural comparison between geopolymers, alkali-activated slag cement and Portland cement
Lecomte, I., Henrist, C., Liégeois, M., Maseri, F., Rulmont, A., & Cloots, R. (2006) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2005.12.021 · Cited by 597
Haha, M. B., Lothenbach, B., Le Saout, G., & Winnefeld, F. (2012) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.08.005 · Cited by 580
Wan, Q., Rao, F., Song, S., García, R. E., Estrella, R. M., Patiño, C. L., & Zhang, Y. (2017) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2017.01.014 · Cited by 481
A calorimetric study of early hydration of alkali-slag cements
Shi, C., & Day, R. L. (1995) · Cement and Concrete Research · doi:10.1016/0008-8846(95)00126-w · Cited by 468
Abdalqader, A. F., Jin, F., & Al-Tabbaa, A. (2016) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2015.12.010 · Cited by 444
Low carbon and low embodied energy materials in buildings: A review
Cabeza, L. F., Barreneche, C., Miró, L., Morera, J. M., Bartolí, E., & Inés Fernández, A. (2013) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2013.03.017 · Cited by 417
Synthesis and strength optimization of one-part geopolymer based on red mud
Ye, N., Yang, J., Liang, S., Hu, Y., Hu, J., Xiao, B., & Huang, Q. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.02.099 · Cited by 363
Designing more sustainable and greener self-compacting concrete
Long, G., Gao, Y., & Xie, Y. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2015.02.072 · Cited by 359
Self-citationDesign and preparation of ultra-high performance concrete with low environmental impact
Shi, Y. H., Long, G., Ma, C., Xie, Y., & He, J. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.12.318 · Cited by 352
Self-citationCarbon dioxide emissions and climate change: policy implications for the cement industry
Rehan, R., & Nehdi, M. L. (2005) · Environmental Science & Policy · doi:10.1016/j.envsci.2004.12.006 · Cited by 337
Sun, W., Chen, H., Luo, X., & Qian, H. (2001) · Cement and Concrete Research · doi:10.1016/s0008-8846(00)00479-8 · Cited by 323
One‐Part Geopolymers Based on Thermally Treated Red Mud/NaOH Blends
Ke, X., Bernal, S. A., Ye, N., Provis, J. L., & Yang, J. (2015) · Journal of the American Ceramic Society · doi:10.1111/jace.13231 · Cited by 283
Mechanical and microstructural characterization of geopolymers derived from red mud and fly ashes
Hu, W., Nie, Q., Huang, B., Shu, X., & He, Q. (2018) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.03.086 · Cited by 274
Ma, C., Long, G., Shi, Y., & Xie, Y. (2018) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.08.060 · Cited by 253
Self-citationThermal Activation of Albite for the Synthesis of One‐Part Mix Geopolymers
Feng, D., Provis, J. L., & van Deventer, J. S. J. (2012) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2011.04925.x · Cited by 244
One-Part Geopolymer Mixes from Geothermal Silica and Sodium Aluminate
Hajimohammadi, A., Provis, J. L., & van Deventer, J. S. J. (2008) · Industrial & Engineering Chemistry Research · doi:10.1021/ie8006825 · Cited by 239
Characterisation of One-Part Geopolymer Binders Made from Fly Ash
Hajimohammadi, A., & van Deventer, J. S. J. (2017) · Waste and Biomass Valorization · doi:10.1007/s12649-016-9582-5 · Cited by 192
Preparation, structure and hydrothermal stability of alternative (sodium silicate-free) geopolymers
Koloušek, D., Brus, J., Urbanova, M., Andertova, J., Hulinsky, V., & Vorel, J. (2007) · Journal of Materials Science · doi:10.1007/s10853-007-1910-5 · Cited by 175
Mobili, A., Belli, A., Giosuè, C., Bellezze, T., & Tittarelli, F. (2016) · Cement and Concrete Research · doi:10.1016/j.cemconres.2016.07.004 · Cited by 175
Sustainability in the EU cement industry: the Italian and German experiences
Supino, S., Malandrino, O., Testa, M., & Sica, D. (2016) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2015.09.022 · Cited by 174
Deir, E., Gebregziabiher, B. S., & Peethamparan, S. (2013) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2013.11.010 · Cited by 152
Evaluating CO2 emission performance in China’s cement industry: An enterprise perspective
Cai, B., Jinnan, W., He, J. Y., & Geng, Y. (2015) · Applied Energy · doi:10.1016/j.apenergy.2015.11.006 · Cited by 152
Nie, Q., Hu, W., Ai, T., Huang, B., Shu, X., & He, Q. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.08.144 · Cited by 152
Utilization of the black tea powder as multifunctional admixture for the hemihydrate gypsum
Huang, Y., Xu, C., Li, H., Jiang, Z., Gong, Z., Yang, X., & Chen, Q. (2018) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.10.304 · Cited by 132
Peng, M. X., Wang, Z. H., Shen, S. H., & Xiao, Q. G. (2014) · Materials and Structures · doi:10.1617/s11527-014-0350-3 · Cited by 109
Preliminary study on combined-alkali–slag paste materials
Li, Y., & Sun, Y. N. (2000) · Cement and Concrete Research · doi:10.1016/s0008-8846(00)00269-6 · Cited by 89
Micromechanical properties of alkali-activated slag cement binders
Thomas, R. J., Gebregziabiher, B. S., Giffin, A., & Peethamparan, S. (2018) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2018.04.003 · Cited by 82
Preparation and characterization of one-part non-Portland cement
Abdel‐Gawwad, H. A., El-Aleem, S. A., & Ouda, A. S. (2015) · Ceramics International · doi:10.1016/j.ceramint.2015.08.096 · Cited by 81
Investigation of the strength development of cast-in-place geopolymer piles with heating systems
Hu, W., Nie, Q., Huang, B., & Shu, X. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.01.155 · Cited by 48
Cited by
Advances in geopolymer materials: A comprehensive review
Cong, P., & Cheng, Y. (2021) · Journal of Traffic and Transportation Engineering (English Edition) · doi:10.1016/j.jtte.2021.03.004 · Cited by 481
Xiao, R., Ma, Y., Jiang, X., Zhang, M., Zhang, Y., Wang, Y., Huang, B., & He, Q. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.119610 · Cited by 359
Metadata
- Authors
- Ma, C., Zhao, B., Guo, S., Long, G., & Xie, Y.
- Venue
- Journal of Cleaner Production
- Publisher
- Elsevier BV
- Published
- 2019-05
- Volume
- 220
- Pages
- 188-199
- ISSN
- 0959-6526 (ISSN-L)
- OpenAlex
- W2914279912
- Cited by
- 273
- References
- 44
- FWCI
- 19.81
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.