The DOI matches its Crossref record; 42 of the 42 references it cites were found in a registry or an index.
Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using X-ray computed tomography
Open accessAbstract
We used X-ray computed tomography (CT), microscopy and hardness measurements to study Al–Si10–Mg produced by selective laser melting (SLM). Specimens were subject to a series of heat treatments including annealing and precipitation hardening. The specimen interiors were imaged with X-ray CT, allowing the non-destructive quantification and characterisation of pores, including their spatial distribution. The specimens had porosities less than 0.1%, but included some pores with effective cross-sectional diameters up to 260 μm. The largest pores were highly anisotropic, being flat and lying in the plane normal to the build direction. Annealing cycles caused significant coarsening of the microstructure and a reduction of the hardness from (114 ± 3) HV, in the as-built state, to (45 ± 1) HV, while precipitation hardening increased this to a final hardness of (59 ± 1) HV. The pore size and shape distributions were unaffected by the heat treatments. We demonstrate the applicability of CT measurements and quantitative defect analysis for the purposes of SLM process monitoring and refinement.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
NIH Image to ImageJ: 25 years of image analysis
Schneider, C. A., Rasband, W. S., & Eliceiri, K. W. (2012) · Nature Methods · doi:10.1038/nmeth.2089 · Cited by 64,638
A new method for gray-level picture thresholding using the entropy of the histogram
Kapur, J. N., Sahoo, P. K., & Wong, A. K. C. (1985) · Computer Vision, Graphics, and Image Processing · doi:10.1016/0734-189x(85)90125-2 · Cited by 3,658
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
A Review of Additive Manufacturing
Wong, K. V., & Hernandez, A. (2012) · ISRN Mechanical Engineering · doi:10.5402/2012/208760 · Cited by 2,555
Residual stresses in selective laser sintering and selective laser melting
Mercelis, P., & Kruth, J. (2006) · Rapid Prototyping Journal · doi:10.1108/13552540610707013 · Cited by 2,015
Thijs, L., Kempen, K., Kruth, J.-P., & Van Humbeeck, J. (2013) · Acta Materialia · doi:10.1016/j.actamat.2012.11.052 · Cited by 1,917
Vrancken, B., Thijs, L., Kruth, J.-P., & Van Humbeeck, J. (2012) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2012.07.022 · Cited by 1,896
Maire, E., & Withers, P. J. (2014) · International Materials Reviews · doi:10.1179/1743280413y.0000000023 · Cited by 1,374
Reducing porosity in AlSi10Mg parts processed by selective laser melting
Aboulkhair, N. T., Everitt, N. M., Ashcroft, I., & Tuck, C. (2014) · Additive Manufacturing · doi:10.1016/j.addma.2014.08.001 · Cited by 1,281
Self-citationRead, N., Wang, W., Essa, K., & Attallah, M. M. (2015) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2014.09.044 · Cited by 1,218
Effect of the build orientation on the mechanical properties and fracture modes of SLM Ti–6Al–4V
Simonelli, M., Tse, Y. Y., & Tuck, C. (2014) · Materials Science and Engineering: A · doi:10.1016/j.msea.2014.07.086 · Cited by 1,010
Self-citationMicro-architectured materials: past, present and future
Fleck, N. A., Deshpande, V. S., & Ashby, M. F. (2010) · Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences · doi:10.1098/rspa.2010.0215 · Cited by 982
Mechanical Properties of AlSi10Mg Produced by Selective Laser Melting
Kempen, K., Thijs, L., Van Humbeeck, J., & Kruth, J.-P. (2012) · Physics Procedia · doi:10.1016/j.phpro.2012.10.059 · Cited by 849
Single track formation in selective laser melting of metal powders
Yadroitsev, I., Gusarov, A., Yadroitsava, I., & Smurov, I. (2010) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.05.010 · Cited by 827
Prashanth, K. G., Scudino, S., Klauss, H. J., Surreddi, K. B., Löber, L., Wang, Z., Chaubey, A. K., Kühn, U., & Eckert, J. (2014) · Materials Science and Engineering: A · doi:10.1016/j.msea.2013.10.023 · Cited by 803
Evaluations of cellular lattice structures manufactured using selective laser melting
Yan, C., Hao, L., Hussein, A., & Raymont, D. (2012) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2012.06.002 · Cited by 730
Computed tomography for dimensional metrology
Kruth, J. P., Bartscher, M., Carmignato, S., Schmitt, R., De Chiffre, L., & Weckenmann, A. (2011) · CIRP Annals · doi:10.1016/j.cirp.2011.05.006 · Cited by 684
Rapid Manufacturing: An Industrial Revolution for the Digital Age
(2005) · Wiley eBooks · doi:10.1002/0470033991 · Cited by 679
Investigations on residual stresses and deformations in selective laser melting
Zaeh, M. F., & Branner, G. (2010) · Production Engineering · doi:10.1007/s11740-009-0192-y · Cited by 666
Yan, C., Hao, L., Hussein, A., Young, P., & Raymont, D. (2014) · Materials & Design · doi:10.1016/j.matdes.2013.10.027 · Cited by 622
Comparison of density measurement techniques for additive manufactured metallic parts
Spierings, A. B., Schneider, M., & Eggenberger, R. (2011) · Rapid Prototyping Journal · doi:10.1108/13552541111156504 · Cited by 613
Residual Stress within Metallic Model Made by Selective Laser Melting Process
Shiomi, M., Osakada, K., Nakamura, K., Yamashita, T., & Abe, F. (2004) · CIRP Annals · doi:10.1016/s0007-8506(07)60677-5 · Cited by 591
Tammas-Williams, S., Zhao, H., Léonard, F., Derguti, F., Todd, I., & Prangnell, P. B. (2015) · Materials Characterization · doi:10.1016/j.matchar.2015.02.008 · Cited by 590
A practical and systematic review of Weibull statistics for reporting strengths of dental materials
Quinn, J. B., & Quinn, G. D. (2010) · Dental Materials · doi:10.1016/j.dental.2009.09.006 · Cited by 569
Smith, M., Guan, Z., & Cantwell, W. J. (2013) · International Journal of Mechanical Sciences · doi:10.1016/j.ijmecsci.2012.12.004 · Cited by 545
Recent advances in X-ray microtomography applied to materials
Stock, S. R. (2008) · International Materials Reviews · doi:10.1179/174328008x277803 · Cited by 517
Sintering: from Empirical Observations to Scientific Principles
(2014) · Elsevier eBooks · doi:10.1016/c2012-0-00717-x · Cited by 421
Yan, C., Hao, L., Hussein, A., Bubb, S. L., Young, P., & Raymont, D. (2014) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2013.12.004 · Cited by 362
Topology Optimization for Additive Manufacturing
Brackett, D., Ashcroft, I., & Hague, R. (2011) · doi:10.26153/tsw/15300 · Cited by 347
Self-citationSimonelli, M., Tuck, C., Aboulkhair, N. T., Maskery, I., Ashcroft, I., Wildman, R. D., & Hague, R. (2015) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-015-2882-8 · Cited by 342
Self-citationYan, C., Hao, L., Hussein, A., Young, P., Huang, J., & Zhu, W. (2015) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.01.063 · Cited by 329
Flexible manufacturing of metallic products by selective laser melting of powder
Osakada, K., & Shiomi, M. (2006) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2006.01.024 · Cited by 294
An investigation into the compressive properties of stainless steel micro-lattice structures
Ushijima, K., Cantwell, W., Mines, R., Tsopanos, S., & Smith, M. (2011) · Journal of Sandwich Structures & Materials · doi:10.1177/1099636210380997 · Cited by 232
Maskery, I., Aremu, A., Simonelli, M., Tuck, C. J., Wildman, R. D., Ashcroft, I., & Hague, R. (2015) · Experimental Mechanics · doi:10.1007/s11340-015-0021-5 · Cited by 185
Self-citationInfluence of Annealing on Mechanical Properties of Al-20Si Processed by Selective Laser Melting
Ma, P., Prashanth, K., Scudino, S., Jia, Y., Wang, H., Zou, C., Wei, Z., & Eckert, J. (2014) · Metals · doi:10.3390/met4010028 · Cited by 181
(1995) · Elsevier eBooks · doi:10.1016/b978-0-12-524995-9.x5023-5 · Cited by 153
The design of impact absorbing structures for additive manufacture
Brennan-Craddock, J. P. J., Brackett, D., Wildman, R. D., & Hague, R. (2012) · Journal of Physics Conference Series · doi:10.1088/1742-6596/382/1/012042 · Cited by 135
Self-citationPorosity Formation and Prevention in Pulsed Laser Welding
Zhou, J., & Tsai, H.-L. (2006) · ASME Journal of Heat and Mass Transfer · doi:10.1115/1.2724846 · Cited by 126
Numerical modeling of pore size and distribution in foamed titanium
Shen, H., Oppenheimer, S., Dunand, D. C., et al. (2005) · Mechanics of Materials · doi:10.1016/j.mechmat.2005.06.027 · Cited by 115
Alkahari, M. R., FURUMOTO, T., Takashi, U. E. D. A., Hosokawa, A., Tanaka, R., & Aziz, M. S. A. (2012) · Key engineering materials · doi:10.4028/www.scientific.net/kem.523-524.244 · Cited by 99
An error diffusion based method to generate functionally graded cellular structures
Brackett, D. J., Ashcroft, I., Wildman, R. D., & Hague, R. (2014) · Computers & Structures · doi:10.1016/j.compstruc.2014.03.004 · Cited by 51
Self-citationKnowledge Management for Topological Optimization Integration in Additive Manufacturing
Gardan, N. (2014) · International Journal of Manufacturing Engineering · doi:10.1155/2014/356256 · Cited by 21
Cited by
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
Additive manufacturing of metals
Herzog, D., Seyda, V., Wycisk, E., & Emmelmann, C. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.07.019 · Cited by 4,759
Aboulkhair, N. T., Simonelli, M., Parry, L., Ashcroft, I., Tuck, C., & Hague, R. (2019) · Progress in Materials Science · doi:10.1016/j.pmatsci.2019.100578 · Cited by 1,552
Self-citationMaterials for additive manufacturing
Bourell, D., Kruth, J. P., Leu, M., Levy, G., Rosen, D., Beese, A. M., & Clare, A. (2017) · CIRP Annals · doi:10.1016/j.cirp.2017.05.009 · Cited by 1,034
Self-citation
Metadata
- Authors
- Maskery, I., Aboulkhair, N. T., Corfield, M. R., Tuck, C., Clare, A. T., Leach, R. K., Wildman, R. D., Ashcroft, I. A., & Hague, R. J. M.
- Venue
- Materials Characterization
- Publisher
- Elsevier BV
- Published
- 2016-01
- Volume
- 111
- Pages
- 193-204
- ISSN
- 1044-5803 (ISSN-L)
- OpenAlex
- W2187725579
- Cited by
- 317
- References
- 42
- FWCI
- 18.63
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.