The DOI matches its Crossref record; 39 of the 39 references it cites were found in a registry or an index.
Effect of an Electrospray-Generated Ionomer Morphology on Polymer Electrolyte Fuel Cell Performance
Open accessAbstract
Oxygen transport is a serious limiting factor on the performance of polymer electrolyte fuel cells (PEFCs). In the present study, without modification of either the chemical structure of the ionomer or the Pt surface, the oxygen transport resistance in ionomer films (RCL,film) was successfully mitigated via a newly developed electrospray (ES) catalyst layer (CL) preparation. We prepared the CL according to two different ionization modes [positive ionization mode (ESP) and negative ionization mode (ESN)] and ionomer/carbon mass ratios (I/C) of 0.3 and 0.7. The ionomer morphology revealed differences according to the ionization mode, as analyzed by scanning transmission electron microscopy. Spherical and dendritic ionomer morphologies were observed resulting from ESP and ESN, respectively. To quantitatively estimate RCL,film values, limiting current measurements were used. Consequently, the CL prepared by ESN exhibited the lowest RCL,film value compared to that for the conventional pulse-swirl-spray (PSS) method and ESP (I/C 0.3 PSS, 61; ESP, 94; ESN, 40 s m–1; and I/C 0.7 PSS, 68; ESP, 66; ESN, 46 s m–1). Moreover, the difference in the ionomer morphology not only influenced the mass activity at low current density but also helped to implement superior performance at high current density. Therefore, it was confirmed that the decreased thickness of the ionomer film covering the surface of the catalyst with ESN decreased RCL,film by a factor of 1.5 and, as a result, improved the overall PEFC performance by the same factor.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Inkjet printing and spray coating generally need a low viscous ink (e.g., 4.9 mPa s) to avoid blocking the spraying nozzle and decrease the structural defects in the CLs, for example, the ink with a viscosity of 25.3 mPa s [67] may result in the nozzle clogging, making it hard to control the amount of ink sprayed.”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [67]
In the citing paper
“spray coating usually needs a lower catalyst content (the solid concentration is commonly less than 3 wt.%,e.g., ~0.6 wt.% [36], ~1.8 wt.% [104], or 2.5 wt.% [67]) to avoid the blockage of spraying nozzle”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [67]
In the citing paper
“During spray coating, some spraying parameters influence the morphology and structure of the CL and hence the performance of the cell, such as the nozzle height [104], electrospray mode [67], or spraying voltage [163].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [67]
In the citing paper
“The CL fabricated by the electrospray with negative ionization mode shows a decreased thickness of ionomer film covering catalysts, which will reduce the local gas transport resistance through the ionomer film.”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [67]
In the citing paper
“Seonghun et al. [67] found that the ionization mode of electrospray has an influence on the morphology of ionomer and then impacts the ionomer film covering catalysts.”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [67]
Citations
Cites
Opportunities and challenges for a sustainable energy future
Chu, S., & Majumdar, A. (2012) · Nature · doi:10.1038/nature11475 · Cited by 12,550
Electrocatalyst approaches and challenges for automotive fuel cells
Debe, M. K. (2012) · Nature · doi:10.1038/nature11115 · Cited by 5,885
On the evaporation of small ions from charged droplets
Iribarne, J. V., & Thomson, B. A. (1976) · The Journal of Chemical Physics · doi:10.1063/1.432536 · Cited by 1,281
Kongkanand, A., & Mathias, M. F. (2016) · The Journal of Physical Chemistry Letters · doi:10.1021/acs.jpclett.6b00216 · Cited by 1,202
Electrospray: From ions in solution to ions in the gas phase, what we know now
Kebarle, P., & Verkerk, U. H. (2009) · Mass Spectrometry Reviews · doi:10.1002/mas.20247 · Cited by 905
Unraveling the Mechanism of Electrospray Ionization
Konermann, L., Ahadi, E., Rodriguez, A. D., & Vahidi, S. (2013) · Analytical Chemistry · doi:10.1021/ac302789c · Cited by 735
Makharia, R., Mathias, M. F., & Baker, D. R. (2005) · Journal of The Electrochemical Society · doi:10.1149/1.1888367 · Cited by 514
Analysis of Oxygen-Transport Diffusion Resistance in Proton-Exchange-Membrane Fuel Cells
Nonoyama, N., Okazaki, S., Weber, A. Z., Ikogi, Y., & Yoshida, T. (2011) · Journal of The Electrochemical Society · doi:10.1149/1.3546038 · Cited by 512
Measurement of Oxygen Transport Resistance in PEM Fuel Cells by Limiting Current Methods
Baker, D. R., Caulk, D. A., Neyerlin, K. C., & Murphy, M. W. (2009) · Journal of The Electrochemical Society · doi:10.1149/1.3152226 · Cited by 510
Park, Y.-C., Tokiwa, H., Kakinuma, K., Watanabe, M., & Uchida, M. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.02.091 · Cited by 389
Self-citation
Cited by
Xu, Q., Zhang, L., Zhang, J., Wang, J., Hu, Y., Jiang, H., & Li, C. (2022) · EnergyChem · doi:10.1016/j.enchem.2022.100087 · Cited by 341
Liu, H., Ney, L., Zamel, N., & Li, X. (2022) · Applied Sciences · doi:10.3390/app12083776 · Cited by 85
Electrode Engineering for Electrochemical CO2 Reduction
Li, G., Yan, T., Chen, X., Liu, H., Zhang, S., & Ma, X. (2022) · Energy & Fuels · doi:10.1021/acs.energyfuels.2c00271 · Cited by 52
Conde, J. J., Ferreira-Aparicio, P., & Chaparro, A. M. (2021) · ACS Applied Energy Materials · doi:10.1021/acsaem.1c01445 · Cited by 49
Kobayashi, A., Fujii, T., Takeda, K., Tamoto, K., Kakinuma, K., & Uchida, M. (2021) · ACS Applied Energy Materials · doi:10.1021/acsaem.1c02836 · Cited by 46
Self-citation
Metadata
- Authors
- Cho, S., Tamoto, K., & Uchida, M.
- Affiliations
- University of Yamanashi (JP)
- Corresponding author
- Uchida, Makoto
- ORCID
- Uchida, Makoto
- Venue
- Energy & Fuels
- Publisher
- American Chemical Society (ACS)
- Published
- 2020-09-16
- Volume
- 34
- Issue
- 11
- Pages
- 14853-14863
- ISSN
- 0887-0624 (ISSN-L)
- 1520-5029
- OpenAlex
- W3087551014
- Cited by
- 24
- References
- 39
- Citations by year
- 2026: 4 · 2025: 2 · 2024: 8 · 2023: 3 · 2022: 4 · 2021: 3
- FWCI
- 0.86
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Locations
- Energy & Fuels (publishedVersion, cc-by-nc-nd)
- Funders
- Ministry of Education, Culture, Sports, Science and Technology (NA)
- New Energy and Industrial Technology Development Organization (NA)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Materials Science › Materials Chemistry › Advancements in Solid Oxide Fuel Cells
- Keywords
- proton exchange membrane fuel cells, electrospray deposition, catalyst layer, ionomer morphology, oxygen transport resistance, ionization mode, limiting current, mass activity, catalyst layer thickness
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effect of an Electrospray-Generated Ionomer Morphology on Polymer Electrolyte Fuel Cell Performance. https://app.cochat.ai/papers/10.1021/acs.energyfuels.0c02337
- The paper
- Cho, S., Tamoto, K., & Uchida, M. (2020). Effect of an Electrospray-Generated Ionomer Morphology on Polymer Electrolyte Fuel Cell Performance. Energy & Fuels. https://doi.org/10.1021/acs.energyfuels.0c02337
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.