Student or educator? Sign up with your school email and get 6 months of Pro free.
CoChat

The DOI matches its Crossref record; 49 of the 50 references it cites were found in a registry or an index; 5 of the 16 sources its claims cite were checked for support.

Monolithically Integrated Perovskite Semiconductor Lasers on Silicon Photonic Chips by Scalable Top-Down Fabrication

Open access

Abstract

High Resolution Image Download MS PowerPoint Slide Metal-halide perovskites are promising lasing materials for the realization of monolithically integrated laser sources, the key components of silicon photonic integrated circuits (PICs). Perovskites can be deposited from solution and require only low-temperature processing, leading to significant cost reduction and enabling new PIC architectures compared to state-of-the-art lasers realized through the costly and inefficient hybrid integration of III−V semiconductors. Until now, however, due to the chemical sensitivity of perovskites, no microfabrication process based on optical lithography (and, therefore, on existing semiconductor manufacturing infrastructure) has been established. Here, the first methylammonium lead iodide perovskite microdisc lasers monolithically integrated into silicon nitride PICs by such a top-down process are presented. The lasers show a record low lasing threshold of 4.7 μJcm –2 at room temperature for monolithically integrated lasers, which are complementary metal–oxide–semiconductor compatible and can be integrated in the back-end-of-line processes.

Overview

CoChat Summary

TL;DR

The paper reports MAPbI3 perovskite micro-disc lasers monolithically integrated into silicon nitride photonic integrated circuits using a scalable top-down optical lithography and ICP RIE process. The lasers show a record low room-temperature lasing threshold of 4.7 µJ cm⁻² for monolithically integrated CMOS-compatible lasers, with reproducibility across 83 devices on 4 PICs.

Key findings

  • MAPbI3 micro-disc lasers coupled to Si3N4 bus waveguides lased at room temperature under optical pumping, with thresholds of 7.1 µJ cm⁻², 4.7 µJ cm⁻², and 7.1 µJ cm⁻² for radii of 4.3 µm, 6 µm, and 8.3 µm, respectively; emission saturated at 18, 11, and 19 µJ cm⁻².
  • The best lasing peak had a FWHM of 1.1 nm and Q = 709; scattering losses were estimated at 27.7 dB/cm due to perovskite roughness.
  • 83 tested devices on 4 different PICs showed comparable lasing thresholds and spectral characteristics; FSR was inversely proportional to disc diameter, but measured FSRs exceeded calculated values by up to 52%, attributed to chlorine intake at etched edges.
  • A polycrystalline FDTD model using random grains of 50–200 nm reproduced measured behavior: simulated roundtrip transmission was 0.56 versus 0.44 extracted from a 4.3 µm disc with Q = 650.

Methods

  • Fabrication: 6-inch Si wafers with 2.2 µm thermal SiO2, 250 nm LPCVD Si3N4 waveguides, LTO SiO2 planarization; MAPbI3 deposited by spin-coating from 1 M MAI/PbI2/DMSO in DMF with chlorobenzene drip and two-step annealing (45 °C, 5 min + 100 °C, 10 min); patterned by double-layer resist optical contact lithography and single-step Cl2/CF4 ICP RIE; 1 µm PMMA cladding.
  • Characterization: SEM, XRD, EDX, and PL mapping; optical pumping with 120 fs pulses at 630 nm and 250 kHz at room temperature in ambient conditions; output collected from the Si3N4 bus waveguide edge 5 mm away, passed through a polarizer, and recorded with a 0.4 nm resolution spectrometer.
  • Simulations: analytical WGM model and Lumerical FDTD for directional coupler optimization, including a model with randomly generated crystal grains to represent polycrystalline MAPbI3 morphology.

Limitations

  • Stated: the lithographic tool could not achieve the optimal 150 nm bus waveguide offset and 50 nm gap, so disc positions were varied in 250 nm steps over ±1.25 µm to ensure at least one nearly optimal structure.
  • Stated: perovskite chemical reactivity and instability remain barriers to established semiconductor fabrication; devices were protected only by 1 µm PMMA, and commercial reliability would require hermetic packaging, moisture barriers, and stability/degradation studies.
  • Evident: lasing is optically pumped, not electrically pumped; the paper notes that electrically pumped lasers will require efficient carrier injection. The low Q (709) and high scattering losses, measured-versus-calculated FSR discrepancy up to 52%, and FSR standard deviation of 1.3 nm within a sample all indicate performance limits tied to perovskite roughness and polycrystalline morphology.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1021/acs.nanolett.8b02811

Cites

49 of 49 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Image 1
From the PDF
Figure 1 (a) Sketch of a MAPbI3 disc laser integrated on a silicon nitride photonic chip. (b) Cross-section of the disc laser. (c) The fabrication process fl ow (consequent steps marked with arrows): planarized silicon nitride photonic chip → deposition of MAPbI3 → deposition of the bottom resist layer → deposition of the top photoactive resist layer → development of the second resist layer → pattern transfer by Cl2/CF4 plasma → resist stripping by dissolving the bottom resist layer and lifting the top layer → deposition of 1 μ m thick PMMA cladding.
Figure 1 (a) Sketch of a MAPbI3 disc laser integrated on a silicon nitride photonic chip. (b) Cross-section of the disc laser. (c) The fabrication process fl ow (consequent steps marked with arrows): planarized silicon nitride photonic chip → deposition of MAPbI3 → deposition of the bottom resist layer → deposition of the top photoactive resist layer → development of the second resist layer → pattern transfer by Cl2/CF4 plasma → resist stripping by dissolving the bottom resist layer and lifting the top layer → deposition of 1 μ m thick PMMA cladding.From the PDF
Figure 2 Physical characterization of fabricated perovskite microdiscs. (a) SEM micrograph showing MAPbI 3 disc on SiO2 substrate after resist stripping. Inset: SEM micrograph at a higher magni fi cation depicting perovskite fi lm morphology. Crystal grain sizes ranged from 50 to 200 nm. (b) SEM micrograph of an edge of a patterned MAPbI3 disc after resist-stripping taken at a 75 ° angle. (c) XRD characterization of a sample containing patterned perovskite structures before (blue) and after (red) the resist stripping compared to a pristine perovskite fi lm (black). (d) EDX spectra of the perovskite disc taken close to the discs edge. A trace of chlorine absorbed from the etch plasma was detected through the appearance of a weak peak around 2.62 eV. (e) Map of photoluminescence of MAPbI3 discs fi ltered with a 15 nm broad fi lter at 760 nm. (f) Map of photoluminescence of MAPbI3 discs fi ltered with a 15 nm broad σ fi lter at 766 nm.
Figure 2 Physical characterization of fabricated perovskite microdiscs. (a) SEM micrograph showing MAPbI 3 disc on SiO2 substrate after resist stripping. Inset: SEM micrograph at a higher magni fi cation depicting perovskite fi lm morphology. Crystal grain sizes ranged from 50 to 200 nm. (b) SEM micrograph of an edge of a patterned MAPbI3 disc after resist-stripping taken at a 75 ° angle. (c) XRD characterization of a sample containing patterned perovskite structures before (blue) and after (red) the resist stripping compared to a pristine perovskite fi lm (black). (d) EDX spectra of the perovskite disc taken close to the discs edge. A trace of chlorine absorbed from the etch plasma was detected through the appearance of a weak peak around 2.62 eV. (e) Map of photoluminescence of MAPbI3 discs fi ltered with a 15 nm broad fi lter at 760 nm. (f) Map of photoluminescence of MAPbI3 discs fi ltered with a 15 nm broad σ fi lter at 766 nm.From the PDF
Figure 3 (a) Emission spectra of a disc with 6 μ m radius pumped at 0.74 and 1.04 of the threshold pump fl uence ( P th ). (b) Intensity of the emission peak of discs with di ff erent radii vs pump pulse fl uence.
Figure 3 (a) Emission spectra of a disc with 6 μ m radius pumped at 0.74 and 1.04 of the threshold pump fl uence ( P th ). (b) Intensity of the emission peak of discs with di ff erent radii vs pump pulse fl uence.From the PDF
Figure 4 (a) Spectra of lasers with varying radii located on di ff erent samples at excitation of 1.15 × P th. (b) Average FSR dependency on radius R of the discs (black line) compared to analytically calculated FSR (blue line). Black points show measured FSRs of all 83 measured devices. (c) Measured spectra of a disc laser with R = 6 μ m taken at a polarizer angle varied with 15 ° steps.
Figure 4 (a) Spectra of lasers with varying radii located on di ff erent samples at excitation of 1.15 × P th. (b) Average FSR dependency on radius R of the discs (black line) compared to analytically calculated FSR (blue line). Black points show measured FSRs of all 83 measured devices. (c) Measured spectra of a disc laser with R = 6 μ m taken at a polarizer angle varied with 15 ° steps.From the PDF
Figure 5 (a) Model of the disc laser used to simulate directional coupler taking into the account polycrystalline morphology of MAPbI 3 . (b) Electric- fi eld amplitude pro fi le in plane of the bus waveguide obtained by the ideal model. (c) Electric- fi eld amplitude pro fi le in the bus waveguide plane obtained with a polycrystalline model. (d) TM WGM in an ideal perovskite disc with no roughness included. (e) TM WGM in a polycrystalline disc. Strong scattering and the generation of high-order modes is visible.
Figure 5 (a) Model of the disc laser used to simulate directional coupler taking into the account polycrystalline morphology of MAPbI 3 . (b) Electric- fi eld amplitude pro fi le in plane of the bus waveguide obtained by the ideal model. (c) Electric- fi eld amplitude pro fi le in the bus waveguide plane obtained with a polycrystalline model. (d) TM WGM in an ideal perovskite disc with no roughness included. (e) TM WGM in a polycrystalline disc. Strong scattering and the generation of high-order modes is visible.From the PDF
Figure 6 (a) Emission spectra of a disc laser ( R = 6 μ m) compared with (b) ASE spectra measured by collecting emission from 15 μ m wide perovskite waveguides. (c) Evolution of WGMs with increasing excitation. Solid lines: spectral positions of resonances. Dashed line: full width at half-maximum of resonance marked with a solid blue line. (d) Normalized spectra of lasers with a 6 μ m radius located on two di ff erent samples. An o ff set was added for clarity.
Figure 6 (a) Emission spectra of a disc laser ( R = 6 μ m) compared with (b) ASE spectra measured by collecting emission from 15 μ m wide perovskite waveguides. (c) Evolution of WGMs with increasing excitation. Solid lines: spectral positions of resonances. Dashed line: full width at half-maximum of resonance marked with a solid blue line. (d) Normalized spectra of lasers with a 6 μ m radius located on two di ff erent samples. An o ff set was added for clarity.From the PDF

Verification

Claims the paper makes

4 Valid · 1 Not valid · 9 Not checked · 40 Own results and interpretations

29 more claims

Create a free account to see all 54 claims and every source verdict.

See all claims — free account
  • It may state two separate claims as one. 15
  • Probably not a substantial claim. 4
  • The quote only partly states this claim. 1

Create a free account to see these claims.

Citations

Cites

Show all 50 references

Cited by

See all 132

Metadata

Authors
Cegielski, P. J., Giesecke, A. L., Neutzner, S., Porschatis, C., Gandini, M., Schall, D., Perini, C. A. R., Bolten, J., Suckow, S., Kataria, S., Chmielak, B., Wahlbrink, T., Petrozza, A., & Lemme, M. C.
Affiliations
  • AMO (Germany) (DE)
  • Italian Institute of Technology (IT)
  • RWTH Aachen University (DE)
Corresponding author
Giesecke, Anna Lena
Venue
Nano Letters
Published
2018-10-02
Volume
18
Issue
11
Pages
6915-6923
ISSN
  • 1530-6984 (ISSN-L)
  • 1530-6992
OpenAlex
W2895106145
Cited by
132
References
50
Citations by year
2026: 11 · 2025: 13 · 2024: 16 · 2023: 21 · 2022: 22 · 2021: 19 · 2020: 16 · 2019: 12 · 2018: 2
FWCI
4.69
Type
journal article
Language
en
Open access
Locations
  • Nano Letters (publishedVersion, other-oa)
  • PubMed (publishedVersion)
  • arXiv (Cornell University) (submittedVersion)
  • RWTH Publications (RWTH Aachen) (submittedVersion, other-oa)
  • Zenodo (CERN European Organization for Nuclear Research) (submittedVersion, other-oa)
  • arXiv (Cornell University)
Funders
  • H2020 Excellent Science (688166)
  • H2020 Marie Sklodowska-Curie Actions (643238)
Topics
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Perovskite Materials and Applications
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Photonic and Optical Devices
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Semiconductor Lasers and Optical Devices
Keywords
monolithic integration, silicon photonics, methylammonium lead iodide, photolithography, lasing threshold, back-end-of-line integration, hybrid integration

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

The claim verdicts this report counts are experimental: their accuracy is not yet measured.

A language model drew the claims from the paper on 2026-10-12, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-12 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Cited sources are checked with a language model’s help (gpt-6-sol).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Monolithically Integrated Perovskite Semiconductor Lasers on Silicon Photonic Chips by Scalable Top-Down Fabrication. https://app.cochat.ai/papers/10.1021/acs.nanolett.8b02811
The paper
Cegielski, P. J., Giesecke, A. L., Neutzner, S., Porschatis, C., Gandini, M., Schall, D., Perini, C. A. R., Bolten, J., Suckow, S., Kataria, S., Chmielak, B., Wahlbrink, T., Petrozza, A., & Lemme, M. C. (2018). Monolithically Integrated Perovskite Semiconductor Lasers on Silicon Photonic Chips by Scalable Top-Down Fabrication. Nano Letters. https://doi.org/10.1021/acs.nanolett.8b02811

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.