Student or educator? Sign up with your school email and get 6 months of Pro free.
PreprintCited by 104Aerosol Filtration and Electrostatic PrecipitationInfection Control and VentilationTextile materials and evaluations

The DOI matches its Crossref record; 70 of the 70 references it cites were found in a registry or an index; 31 of the 53 sources its claims cite were checked for support.

Assessment of N95 and K95 respirator decontamination: fiber integrity, filtration efficiency, and dipole charge density

Open access

Preprint — published as 10.1021/acsami.0c17333 · Paper page

Abstract

Personal protective equipment (PPE) including N95 respirators are critical for persons exposed to SARS-CoV-2. KN95 respirators and N95 decontamination protocols have been described as solutions to a lack of such PPE. However, there are a few materials science studies that characterize the charge distribution and physical changes accompanying disinfection treatments particularly heating. Here, we report the filtration efficiency, dipole charge density, and fiber integrity of pristine N95 and KN95 respirators before and after various decontamination methods. We found that the filter layer of N95 is 8-fold thicker than that of KN95, which explains its 10% higher filtration efficiency (97.03 %) versus KN95 (87.76 %) under pristines condition. After 60 minutes of 70 °C treatment, the filtration efficiency and dipole charge density of N95 became 97.16% and 12.48 μC/m 2 , while those of KN95 were 83.64% and 1.48 μC/m 2 ; moreover, fit factor of N95 was 55 and that of KN95 was 2.7. In conclusion, the KN95 respirator is an inferior alternative of N95 respirator. In both systems, a loss of electrostatic charge does not directly correlate to a decrease in performance.

Overview

CoChat Summary

TL;DR

This study compares N95 and KN95 respirators before and after dry-heat decontamination, measuring filtration efficiency, dipole charge density, fit factor, and fiber integrity. It concludes that KN95 is an inferior alternative to N95, with lower filtration efficiency, fit factor, and dipole charge density, and that loss of electrostatic charge did not directly correlate with filtration performance.

Key findings

  • Pristine N95 had 97.03% filtration efficiency versus 87.76% for KN95; the N95 filter layer was 8-fold thicker than the KN95 filter layer, which the authors say explains the roughly 10% filtration gap.
  • The abstract reports that after 60 minutes of 70°C treatment, N95 filtration efficiency and dipole charge density were 97.16% and 12.48 μC/m², while KN95 values were 83.64% and 1.48 μC/m²; fit factor was 55 for N95 and 2.7 for KN95.
  • Dipole charge density decreased with heat treatment: N95 fell from 38.82 μC/m² pristine to 12.48 μC/m² after 30 minutes at 70°C (67% drop), and KN95 fell from 4.6 to 2.27 μC/m² (50% drop) after 30 minutes. Despite charge loss, filtration changed little; removing all dipole charge with isopropanol reduced N95 filtration efficiency from 97.03% to 94.24%.
  • At 150°C as a positive control, N95 inner spun-bond PP melted at fiber intersections; KN95 showed outer-layer fracture and balloon-shaped cotton fiber expansions, while the melt-blown PP filter layers of both respirators resisted damage.

Methods

  • N95 (3M 1860) and KN95 (Yomasi) respirators were cut into 2 cm squares and heat-treated in a thermostat-controlled oven at 70°C for three 30-minute cycles, with 150°C as a positive control; VHP-sterilized N95s (3M 1860, 3M 1870, 3M 8210) were also tested.
  • Filtration efficiency and fit factor were measured with a PortaCount Plus Model 8020; material filtration used a 2 cm chamber, and fit factor used a probe while an individual wore the respirator in a closed room with two lit candles. SEM (FEI Apreo, 1 kV, 0.10 nA) assessed fiber morphology; dipole charge density was measured with a Trek model 344 electrostatic voltmeter; IPA dipping removed charges.
  • Error bars represent standard deviations of 5 measurements; fiber diameters were calculated with ImageJ.

Limitations

  • The paper does not include a dedicated limitations section. The text itself is a medRxiv preprint marked “not certified by peer review.”
  • Evident limitations from the text: most comparisons use one N95 model (3M 1860) and one KN95 model (Yomasi), so findings may not generalize; fit factor was measured in a closed room with lit candles rather than real-world use; the study does not directly test viral inactivation, relying on cited validation of 70°C; and the authors note no quantitative relationship between dipole charge density and filtration efficiency.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1101/2020.07.07.20148551

Cites

0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Figure 1 Structural components of N95 and KN95 respirators. SEM image shows lateral and front view of multiple layers in (A) N95 and (B) KN95 respirators. (A) N95 is composed of outer layer (spun-bond PP), filter layer (melt-blown PP), and inner layer (spun-bond PP). Green, pink, and yellow arrows point to individual fiber in the outer, filter, and inner layer. (B) KN95 respirator is composed of outer layer (spun-bond PP), filter layer (melt-blown PP), middle layer (cotton), and inner layer that is identical to the outer layer. Blue, pink, and purple arrows point to individual fiber in the outer, filter, and middle layer. Table includes detailed information for each layer: fiber type, fiber diameter, layer thickness, number of layers, and material.
Figure 1 Structural components of N95 and KN95 respirators. SEM image shows lateral and front view of multiple layers in (A) N95 and (B) KN95 respirators. (A) N95 is composed of outer layer (spun-bond PP), filter layer (melt-blown PP), and inner layer (spun-bond PP). Green, pink, and yellow arrows point to individual fiber in the outer, filter, and inner layer. (B) KN95 respirator is composed of outer layer (spun-bond PP), filter layer (melt-blown PP), middle layer (cotton), and inner layer that is identical to the outer layer. Blue, pink, and purple arrows point to individual fiber in the outer, filter, and middle layer. Table includes detailed information for each layer: fiber type, fiber diameter, layer thickness, number of layers, and material.From the PDF
Figure 2 Decontamination of N95 and KN95 respirator. (A -C) Dust removal is seen at the outer layer of N95 respirator. Red circle shows dust particles disappear after heat treatment. (D) filtration efficiencies of N95 after 70 ºC and 150 ºC treatment (E) Dipole charge densities of N95 decrease with heat treatment. (F -G) Few particles are removed at the outer layer of KN95 after 70 ºC treatment. (H) Fiber fracture occurs at 150 ºC treatment. Orange rectangle shows the fracture happens at the outer layer of KN95. (I) filtration efficiencies of KN95 after 70 ºC and 150 ºC treatment. (J) Dipole charge density of KN95 linearly decreases upon heat treatment. Error bars represent the standard deviations of 5 measurements. All scale bars represent 100 µ𝑚.
Figure 2 Decontamination of N95 and KN95 respirator. (A -C) Dust removal is seen at the outer layer of N95 respirator. Red circle shows dust particles disappear after heat treatment. (D) filtration efficiencies of N95 after 70 ºC and 150 ºC treatment (E) Dipole charge densities of N95 decrease with heat treatment. (F -G) Few particles are removed at the outer layer of KN95 after 70 ºC treatment. (H) Fiber fracture occurs at 150 ºC treatment. Orange rectangle shows the fracture happens at the outer layer of KN95. (I) filtration efficiencies of KN95 after 70 ºC and 150 ºC treatment. (J) Dipole charge density of KN95 linearly decreases upon heat treatment. Error bars represent the standard deviations of 5 measurements. All scale bars represent 100 µ𝑚.From the PDF
Figure 3 Comparison of N95 and KN95. Changes of (A) filtration efficiency (B) fit factor (C) dipole charge density of N95 and KN95 respirators after each cycle of 70 ° C treatment. (D) Filtration efficiency of N95 respirators (3M 1860, 3M 1870, 3M 8210) disinfected by VHP method compared with 3M 1860 and KN95 disinfected by 70 ° C heat treatment. (E) The decrease of dipole charge density is shown in the 3M 1860 disinfected by VHP method and 70 ° C heat treatment. (F) Filtration efficiencies between the pristine and chargeless respirators. Dipole charges were removed by isopropanol (IPA) solution. Error bars represent the standard deviations of 5 measurements.
Figure 3 Comparison of N95 and KN95. Changes of (A) filtration efficiency (B) fit factor (C) dipole charge density of N95 and KN95 respirators after each cycle of 70 ° C treatment. (D) Filtration efficiency of N95 respirators (3M 1860, 3M 1870, 3M 8210) disinfected by VHP method compared with 3M 1860 and KN95 disinfected by 70 ° C heat treatment. (E) The decrease of dipole charge density is shown in the 3M 1860 disinfected by VHP method and 70 ° C heat treatment. (F) Filtration efficiencies between the pristine and chargeless respirators. Dipole charges were removed by isopropanol (IPA) solution. Error bars represent the standard deviations of 5 measurements.From the PDF
Figure 4 Fiber deformation at 150 ° C treatment. (A) Inner layer of N95 (no treatment) (B) Melting happens at the fiber intersections. (C) Inner layer of KN95 (no treatment) (D) fiber fracture occurs after 150 ° C treatment . (E) Middle layer of KN95 (no treatment) (F) Balloon-shaped fiber expansions happen after 150 ° C treatment.
Figure 4 Fiber deformation at 150 ° C treatment. (A) Inner layer of N95 (no treatment) (B) Melting happens at the fiber intersections. (C) Inner layer of KN95 (no treatment) (D) fiber fracture occurs after 150 ° C treatment . (E) Middle layer of KN95 (no treatment) (F) Balloon-shaped fiber expansions happen after 150 ° C treatment.From the PDF

Verification

Claims the paper makes

18 Valid · 7 Not valid · 15 Not checked · 56 Own results and interpretations

46 more claims · 6 with their cited sources checked

Create a free account to see all 96 claims and to verify the 4 references still open.

See all claims — free account
  • Probably not a substantial claim. 24
  • It may state two separate claims as one. 32
  • The quote only partly states this claim. 1

Create a free account to see these claims.

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

Each contradiction between two passages listed here was confirmed by an independent check.

2 of 2

Citations

Cites

Show all 0 references

Cited by

See all 104

Metadata

Authors
Yim, W., Cheng, D., Patel, S., Kui, R., Meng, Y. S., & Jokerst, J. V.
Affiliations
University of California San Diego (US)
Corresponding author
Jokerst, Jesse V.
Venue
medRxiv
Publisher
openRxiv
Published
2020-07-09
Volume
12
Issue
49
Pages
54473-54480
ISSN
1944-8244 (ISSN-L)
OpenAlex
W3107154450
Cited by
104
References
0
Citations by year
2026: 5 · 2025: 8 · 2024: 11 · 2023: 22 · 2022: 23 · 2021: 28 · 2020: 7
FWCI
6.88
Type
journal article
Language
en
Open access
Locations
  • ACS Applied Materials & Interfaces (publishedVersion)
  • medRxiv (submittedVersion)
  • PubMed (publishedVersion)
  • PubMed Central (acceptedVersion)
  • PubMed Central (submittedVersion)
  • eScholarship (California Digital Library) (submittedVersion)
Funders
  • National Science Foundation (1845683, HL137187)
  • Tobacco-Related Disease Research Program
  • University of California (R00RG2515)
  • National Institutes of Health (COVID-19)
  • National Institute on Aging (R21AG065776)
  • National Heart, Lung, and Blood Institute (DP2HL137187)
  • National Institute of Allergy and Infectious Diseases (R21AI157957)
  • Division of Materials Research (1845683)
Topics
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Aerosol Filtration and Electrostatic Precipitation
  • Health Sciences › Medicine › Pulmonary and Respiratory Medicine › Infection Control and Ventilation
  • Physical Sciences › Materials Science › Polymers and Plastics › Textile materials and evaluations
Keywords
N95 respirators, respirator decontamination, filtration efficiency, static electricity, heat disinfection, emergency use authorization, personal protective equipment

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

The claim verdicts this report counts are experimental: their accuracy is not yet measured.

A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Cited sources are checked with a language model’s help (gpt-6-sol).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Assessment of N95 and K95 respirator decontamination: fiber integrity, filtration efficiency, and dipole charge density. https://app.cochat.ai/papers/10.1101/2020.07.07.20148551
The paper
Yim, W., Cheng, D., Patel, S., Kui, R., Meng, Y. S., & Jokerst, J. V. (2020). Assessment of N95 and K95 respirator decontamination: fiber integrity, filtration efficiency, and dipole charge density. medRxiv. https://doi.org/10.1101/2020.07.07.20148551

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.