Rheological Investigation on the Microstructure of Fuel Cell Catalyst Inks
The DOI matches its Crossref record; 65 of the 65 references it cites were found in a registry or an index.
Abstract
We present a rheological investigation of fuel cell catalyst inks. The effects of ink parameters, which include carbon black-support structure, Pt presence on carbon support (Pt-carbon), and ionomer (Nafion) concentration, on the ink microstructure of catalyst inks were studied using rheometry in combination with ultrasmall-angle X-ray scattering (USAXS) and dynamic light scattering (DLS). Dispersions of a high-surface-area carbon (HSC), or Ketjen black type, demonstrated a higher viscosity than Vulcan XC-72 carbon due to both a higher internal porosity and a more agglomerated structure that increased the effective particle volume fraction of the inks. The presence of Pt catalyst on both the carbon supports reduced the viscosity through electrostatic stabilization. For carbon-only dispersions (without Pt), the addition of ionomer up to a critical concentration decreased the viscosity due to electrosteric stabilization of carbon agglomerates. However, with Pt-carbon dispersions, the addition of ionomer showed contrasting behavior between Vulcan and HSC supports. In the Pt-Vulcan dispersions, the effect of ionomer addition on the rheology was qualitatively similar to Vulcan dispersions without Pt. The Pt-HSC dispersions showed an increased viscosity with ionomer addition and a strong shear-thinning nature, indicating that Nafion likely flocculated the Pt-HSC aggregates. These results were verified using DLS and USAXS. Further, the observations of the effect of ionomer:carbon ratio and a comparison between carbons of different surface areas provided insights on the microstructure of the catalyst ink corresponding to the optimized I/ C ratio for fuel cell performance reported in the literature.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“When simultaneously dispersing Pt/HSC and Nafion ionomer in the solvent, i.e., the catalyst ink, it presents a shear-thinning nature [53] (Figure 5).”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [53]
In the citing paper
“The viscosity of catalyst ink is generally determined by temperature, the viscosity of solvent, the volume fraction of solids in the ink, and shear rate [53].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [53]
In the citing paper
“When dispersing Pt/HSC (high surface carbon) in the solvent, the fluid exhibits a shear-thinning behavior.”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [53]
In the citing paper
“When dispersing Nafion ionomer in the solvent with a weight ratio from 0.25 to 5.5 wt.%, the dispersion solution still approaches a Newtonian behavior for shear rates above 10 s -1 [52,53].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [53]
In the citing paper
“only a few cases exhibit a nearly Newtonian behavior for shear rate of about 1~1000 s -1 [53,75].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [53]
14 more claims about this paper
Create a free account to see every claim other papers make about this one.
Citations
Cites
The Structure and Rheology of Complex Fluids
Larson, R. G. (1998) · Cited by 4,841
DLS and zeta potential – What they are and what they are not?
Bhattacharjee, S. (2016) · Journal of Controlled Release · doi:10.1016/j.jconrel.2016.06.017 · Cited by 4,702
Litster, S., & McLean, G. (2004) · Journal of Power Sources · doi:10.1016/j.jpowsour.2003.12.055 · Cited by 1,275
Mewis, J., & Wagner, N. J. (2011) · Cambridge University Press eBooks · doi:10.1017/cbo9780511977978 · Cited by 1,142
Small-Angle Scattering from Polymeric Mass Fractals of Arbitrary Mass-Fractal Dimension
Beaucage, G. (1996) · Journal of Applied Crystallography · doi:10.1107/s0021889895011605 · Cited by 1,059
Shear thickening in colloidal dispersions
Wagner, N. J., & Brady, J. F. (2009) · Physics Today · doi:10.1063/1.3248476 · Cited by 994
Long, C. M., Nascarella, M. A., & Valberg, P. A. (2013) · Environmental Pollution · doi:10.1016/j.envpol.2013.06.009 · Cited by 558
Fuel Cell Catalyst Layers: A Polymer Science Perspective
Holdcroft, S. (2014) · Chemistry of Materials · doi:10.1021/cm401445h · Cited by 481
(1997) · Springer eBooks · doi:10.1007/978-94-011-5342-3 · Cited by 442
High-concentration zeta potential measurements using light-scattering techniques
Kaszuba, M., Corbett, J., Watson, F. M., & Jones, A. (2010) · Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences · doi:10.1098/rsta.2010.0175 · Cited by 430
Research works printed but not linked: 2
- 10.1016/s0001-8686(96)90047-0 · doi:10.1016/s0001-8686(96)90047-0 · Paper page
- Derjaguin B., 1941, Acta Physicochem. URSS, 14, 633
Cited by
Items 101–163 of 163
Investigating Electrode‐Ionomer Interface Phenomena for Electrochemical Energy Applications
Jo, S. Y., Kim, H.-J., Park, H., Ahn, C., & Chung, D. Y. (2023) · Chemistry - An Asian Journal · doi:10.1002/asia.202301016 · Cited by 11
Zimmerer, N., Quarz, P., Terhorst, E., Janning, L., Scharfer, P., & Schabel, W. (2025) · Energy Technology · doi:10.1002/ente.202500516 · Cited by 7
Manufacturing and structural control of slurry-cast catalyst layers for AEMFC
Hyun, J., Lee, D. W., Oh, E., Bae, H., Park, J., Doo, G., & Kim, H. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.233161 · Cited by 7
Self-citationEffect of emulsification of catalyst ink on the structure of catalyst layer in PEMFC
Huang, Z., An, Z., Yang, D., Zhang, D., & Ding, Y. (2025) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2025.151830 · Cited by 7
Interrelation between ink viscoelasticity and crack structure of fuel cell microporous layers
Chen, Z., Pan, W., Tang, L., Chen, X., & Wang, F. (2023) · Fuel · doi:10.1016/j.fuel.2023.130629 · Cited by 6
Acheampong, R., Stewart-Thomas, K., Islam, M. N., Dhawan, H., Eastcott, J. I., & Shahgaldi, S. (2025) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2025.138741 · Cited by 6
Suzuki, T., NAGAI, T., & Tsushima, S. (2020) · Journal of Thermal Science and Technology · doi:10.1299/jtst.2021jtst0012 · Cited by 7
Zhang, P., Yang, D., Li, B., Ming, P., Yang, D., & Zhang, C. (2024) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2024.05.069 · Cited by 6
Graded Roll‐to‐Roll Slot Die Coating for High‐Throughput Catalyst Layer Studies
Pätzold, G., Maier, M., Löttert, L., Freiberg, A. T. S., Thiele, S., & Dworschak, D. (2025) · ChemElectroChem · doi:10.1002/celc.202400688 · Cited by 6
Zhao, X., Gao, S., Wang, S., Hou, T., Bao, Z., Guo, W. F., Deng, C., Kong, F., & Yin, G. (2025) · ACS Catalysis · doi:10.1021/acscatal.5c03319 · Cited by 5
Static and dynamic rheo-impedance characterization of PEMFC catalyst inks
Tanaka, A., Mora, J. M., Nagato, K., & Chuang, P. A. (2026) · Electrochemistry Communications · doi:10.1016/j.elecom.2026.108165 · Cited by 5
Effect of Dispersion Method on Ink Rheology and Microstructure of Microporous Layer for PEMFCs
Chen, M., Du, S., Jung, J. C., Zhang, R., Dong, Z., Djilali, N., & Sui, P. (2023) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/acd4ec · Cited by 5
Surface technology should improve PEM fuel cell performance
Mølmen, L., Alexandersson, A., & Leisner, P. (2019) · Transactions of the IMF · doi:10.1080/00202967.2019.1596573 · Cited by 5
Vu, T. H. T., Nguyen, M. D., & Ngoc, A. T. (2021) · Journal of Chemistry · doi:10.1155/2021/6649089 · Cited by 6
Liu, P., Yang, D., Li, B., Zhang, L., Xiao, L., & Chen, H. (2025) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2025.151672 · Cited by 4
Reaction Products Affecting the PEFC Catalyst Ink Property
Uemura, S., Sasabe, T., Sakai, K., Matsumoto, H., Sugimori, H., Shinohara, K., & Hirai, S. (2021) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ac2684 · Cited by 4
Su, Y., Yuan, S., Li, J., Feng, Y., Shen, S., Yan, X., & Zhang, J. (2026) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2025.116163 · Cited by 6
The effect of catalyst ink formulations and slot-die coating parameters on PEMFC GDE fabrication
Felix, C., Vazirgiantzikis, I., Matseke, M. S., Barron, O., & Raphulu, M. C. (2025) · Next Energy · doi:10.1016/j.nxener.2025.100334 · Cited by 4
Quarz, P., Zimmerer, N., Janning, L., Steck, A., Scharfer, P., & Schabel, W. (2025) · Energy Technology · doi:10.1002/ente.202501844 · Cited by 4
Rotary screen printing of catalyst layers for polymer electrolyte membrane fuel cells
Ney, L., Göttlicher, N., Lohmann, R., Klawitter, M., Hog, J., Thombra, N. P., Kiaee, Z., Kegel, I., Schleuniger, J., & Keding, R. J. (2025) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2025.153053 · Cited by 3
Toplak, B., Müller, L., Khan, A. R., Olean‐Oliveira, A., Muhammad, K. Y., Feng, W., Machado, R. R. L., Xing, D., Sheikh, M.-A., Kucklick, L., et al. (2026) · Chemical Engineering Journal · doi:10.1016/j.cej.2026.173316 · Cited by 3
Yoshino, S., Harada, M., Hasegawa, N., Yomo, S., Koiwai, A., Minami, S., Yamakawa, S., & Jinnouchi, R. (2026) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5c17388 · Cited by 3
Su, Y., Yan, C., Zhao, C., Wang, E., Yin, J., Shen, S., Yan, X., & Zhang, J. (2026) · Chemical Engineering Journal · doi:10.1016/j.cej.2026.173503 · Cited by 3
Larsen, T., Christiansen, J. D. C., Royer, J., Laidlaw, F. H. J., Poon, W. C. K., Larsen, T., & Andreasen, S. J. (2024) · Physical Review Applied · doi:10.1103/physrevapplied.22.034023 · Cited by 3
The effect of yielding of dense silica slurry on the uniformity of coated layer
Komoda, Y., Hira, T., Kojo, H., Miura, H., Shibata, Y., Udaka, K., Watanabe, A., & Suzuki, K. (2021) · Journal of Coatings Technology and Research · doi:10.1007/s11998-021-00507-8 · Cited by 3
Feng, C., Zheng, J., Wang, Y., Zhang, C., & Ming, P. (2023) · Applied Materials Today · doi:10.1016/j.apmt.2023.101896 · Cited by 3
Gong, Z., Feng, Z., Tao, L., Chao, W., Chang, Z., & Zhao, P. (2025) · Fuel Cells · doi:10.1002/fuce.70015 · Cited by 2
Yang, D., Guo, Y., Zhang, Z., Wang, J., Zheng, W., Yang, D., Ming, P., & Li, B. (2026) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2026.154539 · Cited by 2
Shelf-life of ball-milled catalyst inks for the fabrication of fuel cell electrodes
Baez-Cotto, C. M., Foster, J. G., Godoy, A. O., Cleve, T. V., Young, E., Pylypenko, S., Janković, J., Ulsh, M., & Mauger, S. A. (2024) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2024.10.273 · Cited by 2
Self-citationElshamy, M., Metzler, L., Disch, J., Vierrath, S., & Koch, S. (2024) · RSC Advances · doi:10.1039/d4ra03969f · Cited by 2
Chen, Y., Yang, D., Kang, J., Li, B., Yang, D., Ming, P., & Zhang, C. (2025) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2025.150679 · Cited by 2
Kaplan, M. (2025) · Journal of Innovative Engineering and Natural Science · doi:10.61112/jiens.1640685 · Cited by 1
Yomo, S., Yoshino, S., Hasegawa, N., Harada, M., & Yamakawa, S. (2025) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ae2261 · Cited by 2
Takeshita, K., Wijakmatee, T., Matsumoto, H., Yoshikawa, S., & Saito, T. (2026) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2026.139952 · Cited by 1
Yamagata, Y., & Wataya, T. (2026) · Chemical Engineering Journal Advances · doi:10.1016/j.ceja.2026.101188 · Cited by 1
Shitanda, I., Tsunegi, H., Yamagata, Y., Miyamoto, K., Watanabe, H., & Itagaki, M. (2026) · Electrochemistry · doi:10.5796/electrochemistry.26-00048 · Cited by 1
Process model for multilayer slide coating of polymer electrolyte membrane fuel cells
Tjiptowidjojo, K., Park, J., Mauger, S. A., Ulsh, M., & Schunk, P. R. (2021) · Journal of Coatings Technology and Research · doi:10.1007/s11998-021-00508-7 · Cited by 1
Self-citationConstruction of An Efficient Electrode with Ionomer Binding Sites for Stable Water ElectrolysisPreprint
Tao, H. B., Wei, X., Zheng, N., Lao, K., Wen, L., Lin, H., Chen, L., Huang, M., Liu, X., Pan, Y., et al. (2025) · Research Square · doi:10.21203/rs.3.rs-7906062/v1 · Cited by 1
Bapat, S., & Segets, D. (2020) · ChemRxiv · doi:10.26434/chemrxiv.12278360
DOE EERE AMO Electrochemistry for Manufacturing (Workshop Report)
Peretti, K., Lucci, F. R., Kidder, M. K., Deutsch, T. G., & Oshman, C. J. (2022) · OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information) · doi:10.2172/1871276
Nano-inks for fuel cells application
Carneiro, L. P. T., Ferreira, N. S., Pinto, A. M. F. R., & Sales, M. G. F. (2023) · Elsevier eBooks · doi:10.1016/b978-0-323-91145-0.00008-6 · Cited by 1
PROCESSING OF HIERARCHICALLY STRUCTURED ELECTRODES WITH VARYING CATALYSTS FOR PEM FUEL CELLS
Zimmerer, N., Quarz, P., Janning, L., Risinger, J., Scharfer, P., & Schabel, W. (2024) · Qucosa (Saxon State and University Library Dresden)
The Solvent Effect on Ionomer Self-Assembly: From Molecular Morphology to Catalyst Layer Performance
Yang, D., Chu, T., Guo, Y., Zhang, Z., Wang, J., Zheng, W., Yang, D., Ming, P., & Li, B. (2025) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5c18925
Ir–Ru Particles Enable Low-Loading Acidic Oxygen Evolution for Integrated Solar Devices
Conrad, C. L., Fehr, A., Botello, C. R., Elias, W. C., Jacobs, H. P., Yazdi, S., Terlier, T., Mohite, A. D., & Wong, M. S. (2026) · ACS electrochemistry. · doi:10.1021/acselectrochem.5c00473
Chen, H., Yang, D., Chu, T., Chen, B., Zheng, W., Wang, J. C., Yang, D., Ming, P., & Li, B. (2026) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6c02112 · Cited by 1
Murugaiah, D. K., Islam, M. N., Stewart-Thomas, K., Eastcott, J. I., Dhawan, H., & Shahgaldi, S. (2026) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2026.140463
Low-fluorine ionomers in catalyst layers: Toward PFSA-reduced PEM fuel cells
Makhlooghiazad, F., Hirth, L., Gierse, S., Gallastegui, A., Casado, N., Kiaee, Z., & Zamel, N. (2026) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2026.155287
Burghart, J., Cogné, H., Meeker, S. P., Medina‐González, Y., & Ovarlez, G. (2026) · Macromolecules · doi:10.1021/acs.macromol.6c01444
Kwan, J. T. H., Daniel, L., Gill, A. P. S., Bonakdarpour, A., & Wilkinson, D. P. (2026) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ae8412
Quarz, P. (2026) · Repository KITopen (Karlsruhe Institute of Technology) · doi:10.5445/ir/1000195965
Role of initial Pt/C aggregate state in PEFC catalyst ink microstructure formation
Miskan, M., Tanaka, A., Sakuramoto, K., Nagato, K., & Tsujiguchi, T. (2026) · Chemical Engineering Journal · doi:10.1016/j.cej.2026.180577
Manufacturing Challenges and Mechanical Reliability of Polymer Electrolyte Fuel Cells: A Review
Boshoman, S. B., Fatoba, O. S., & Jen, T.-C. (2026) · IEEE International Conference on Mechanical and Intelligent Manufacturing Technologies (ICMIMT) · doi:10.1109/icmimt69639.2026.11642841
Chan, A.-L., Yu, H., Bassinger, M., Soetrisno, D. D., Ailey, K. S., Khandavalli, S., & Alia, S. M. (2026) · ACS Applied Energy Materials · doi:10.1021/acsaem.6c01333
Self-citationLee, S. J., Choi, H. W., & Song, Y. S. (2026) · Colloid & Polymer Science · doi:10.1007/s00396-026-05715-5
Kim, K.-D., KIM, J., Kang, B., LEE, S., PARK, J., BAEK, C.-M., & Kim, T. (2026) · Journal of Hydrogen and New Energy · doi:10.7316/jhne.2026.37.4.359
Self-citationZhang, D. Y., Young, E., Cleve, T. V., Yu, H., Soetrisno, D. D., Reeves, K. S., Mauger, S. A., & Baez-Cotto, C. M. (2026) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2026.157024
Self-citationExploring the potential of image feature extraction for catalyst layer characterization
Utsch, N., Froning, D., Scheepers, F., Jain, M., Shviro, M., Lehnert, W., & Mechler, A. K. (2026) · Nanoscale · doi:10.1039/d6nr01185c
Acheampong, R., Stewart-Thomas, K., Islam, M. N., Dhawan, H., Eastcott, J. I., & Shahgaldi, S. (2026) · Journal of Power Sources · doi:10.1016/j.jpowsour.2026.241543
Probing ionomer distribution in PEMFC catalyst layers: AFM and DEM enabled microstructure analysisPreprint
Vijayaraghavan, S. B., Lill, B., Bhutia, P. T., Renner, T., Grcic, S., Baldofski, M., & Franco, A. A. (2026) · ChemRxiv · doi:10.26434/chemrxiv.15011232/v1
Kim, S., Woo, S., Park, S., Jung, N., Yim, S., & Kang, Y. S. (2026) · Fuel Cells · doi:10.1002/fuce.70180
Metadata
- Authors
- Khandavalli, S., Park, J. H., Kariuki, N. N., Myers, D. J., Stickel, J. J., Hurst, K., Neyerlin, K. C., Ulsh, M., & Mauger, S. A.
- Affiliations
- National Laboratory of the Rockies (US)
- Argonne National Laboratory (US)
- Corresponding author
- Mauger, Scott A.
- ORCID
- Venue
- ACS Applied Materials & Interfaces
- Publisher
- American Chemical Society (ACS)
- Published
- 2018-12-10
- Volume
- 10
- Issue
- 50
- Pages
- 43610-43622
- ISSN
- 1944-8244 (ISSN-L)
- 1944-8252
- OpenAlex
- W2903943595
- Cited by
- 153
- References
- 65
- Citations by year
- 2026: 20 · 2025: 21 · 2024: 21 · 2023: 26 · 2022: 16 · 2021: 28 · 2020: 13 · 2019: 8
- FWCI
- 4.69
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- ACS Applied Materials & Interfaces (publishedVersion)
- PubMed (publishedVersion)
- OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information) (submittedVersion)
- Funders
- U.S. Department of Energy
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Chemical Engineering › Fluid Flow and Transfer Processes › Rheology and Fluid Dynamics Studies
- Keywords
- rheology, carbon black support, Nafion ionomer, ionomer-to-carbon ratio, high surface area carbon, Ketjen Black, Vulcan XC-72, viscosity, shear thinning, electrostatic stabilization, electrosteric stabilization, particle agglomeration, flocculation, dynamic light scattering
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.