Rheological Investigation on the Microstructure of Fuel Cell Catalyst Inks
The DOI matches its Crossref record; 65 of the 65 references it cites were found in a registry or an index.
Abstract
We present a rheological investigation of fuel cell catalyst inks. The effects of ink parameters, which include carbon black-support structure, Pt presence on carbon support (Pt-carbon), and ionomer (Nafion) concentration, on the ink microstructure of catalyst inks were studied using rheometry in combination with ultrasmall-angle X-ray scattering (USAXS) and dynamic light scattering (DLS). Dispersions of a high-surface-area carbon (HSC), or Ketjen black type, demonstrated a higher viscosity than Vulcan XC-72 carbon due to both a higher internal porosity and a more agglomerated structure that increased the effective particle volume fraction of the inks. The presence of Pt catalyst on both the carbon supports reduced the viscosity through electrostatic stabilization. For carbon-only dispersions (without Pt), the addition of ionomer up to a critical concentration decreased the viscosity due to electrosteric stabilization of carbon agglomerates. However, with Pt-carbon dispersions, the addition of ionomer showed contrasting behavior between Vulcan and HSC supports. In the Pt-Vulcan dispersions, the effect of ionomer addition on the rheology was qualitatively similar to Vulcan dispersions without Pt. The Pt-HSC dispersions showed an increased viscosity with ionomer addition and a strong shear-thinning nature, indicating that Nafion likely flocculated the Pt-HSC aggregates. These results were verified using DLS and USAXS. Further, the observations of the effect of ionomer:carbon ratio and a comparison between carbons of different surface areas provided insights on the microstructure of the catalyst ink corresponding to the optimized I/ C ratio for fuel cell performance reported in the literature.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“When simultaneously dispersing Pt/HSC and Nafion ionomer in the solvent, i.e., the catalyst ink, it presents a shear-thinning nature [53] (Figure 5).”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [53]
In the citing paper
“The viscosity of catalyst ink is generally determined by temperature, the viscosity of solvent, the volume fraction of solids in the ink, and shear rate [53].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [53]
In the citing paper
“When dispersing Pt/HSC (high surface carbon) in the solvent, the fluid exhibits a shear-thinning behavior.”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [53]
In the citing paper
“When dispersing Nafion ionomer in the solvent with a weight ratio from 0.25 to 5.5 wt.%, the dispersion solution still approaches a Newtonian behavior for shear rates above 10 s -1 [52,53].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [53]
In the citing paper
“only a few cases exhibit a nearly Newtonian behavior for shear rate of about 1~1000 s -1 [53,75].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [53]
14 more claims about this paper
Create a free account to see every claim other papers make about this one.
Citations
Cites
The Structure and Rheology of Complex Fluids
Larson, R. G. (1998) · Cited by 4,841
DLS and zeta potential – What they are and what they are not?
Bhattacharjee, S. (2016) · Journal of Controlled Release · doi:10.1016/j.jconrel.2016.06.017 · Cited by 4,702
Litster, S., & McLean, G. (2004) · Journal of Power Sources · doi:10.1016/j.jpowsour.2003.12.055 · Cited by 1,275
Mewis, J., & Wagner, N. J. (2011) · Cambridge University Press eBooks · doi:10.1017/cbo9780511977978 · Cited by 1,142
Small-Angle Scattering from Polymeric Mass Fractals of Arbitrary Mass-Fractal Dimension
Beaucage, G. (1996) · Journal of Applied Crystallography · doi:10.1107/s0021889895011605 · Cited by 1,059
Shear thickening in colloidal dispersions
Wagner, N. J., & Brady, J. F. (2009) · Physics Today · doi:10.1063/1.3248476 · Cited by 994
Long, C. M., Nascarella, M. A., & Valberg, P. A. (2013) · Environmental Pollution · doi:10.1016/j.envpol.2013.06.009 · Cited by 558
Fuel Cell Catalyst Layers: A Polymer Science Perspective
Holdcroft, S. (2014) · Chemistry of Materials · doi:10.1021/cm401445h · Cited by 481
(1997) · Springer eBooks · doi:10.1007/978-94-011-5342-3 · Cited by 442
High-concentration zeta potential measurements using light-scattering techniques
Kaszuba, M., Corbett, J., Watson, F. M., & Jones, A. (2010) · Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences · doi:10.1098/rsta.2010.0175 · Cited by 430
Research works printed but not linked: 2
- 10.1016/s0001-8686(96)90047-0 · doi:10.1016/s0001-8686(96)90047-0 · Paper page
- Derjaguin B., 1941, Acta Physicochem. URSS, 14, 633
Cited by
Recent Advances on PEM Fuel Cells: From Key Materials to Membrane Electrode Assembly
Mo, S., Du, L., Huang, Z., Chen, J., Zhou, Y., Wu, P., Meng, L., Wang, N., Xing, L., Zhao, M., et al. (2023) · Electrochemical Energy Reviews · doi:10.1007/s41918-023-00190-w · Cited by 277
“Moreover, a high-surface-area carbon support demonstrates a higher ink viscosity due to both a higher internal porosity and a more agglomerated structure that increases the effective particle volume fraction [176].”
Suter, T. A. M., Smith, K., Hack, J., Rasha, L., Rana, Z., Angel, G. M. A., Shearing, P. R., Miller, T. S., & Brett, D. J. L. (2021) · Advanced Energy Materials · doi:10.1002/aenm.202101025 · Cited by 245
Wang, M., Park, J. H., Kabir, S., Neyerlin, K. C., Kariuki, N. N., Lv, H., Stamenkovic, V. R., Myers, D. J., Ulsh, M., & Mauger, S. A. (2019) · ACS Applied Energy Materials · doi:10.1021/acsaem.9b01037 · Cited by 192
Self-citationThe Controllable Design of Catalyst Inks to Enhance PEMFC Performance: A Review
Guo, Y., Pan, F., Chen, W., Ding, Z., Yang, D., Li, B., Ming, P., & Zhang, C. (2021) · Electrochemical Energy Reviews · doi:10.1007/s41918-020-00083-2 · Cited by 175
“In addition, the limiting parameter affecting ink deposition processes and achievable manufacturing speeds (the shear rate) is ink rheology [10] in which viscosity as a steady-state rheological property of inks is generally closely related to ink component properties, solid contents and I/C ratios [172, 216, 220].”
BackgroundMethodInfluentialKabir, S., Myers, D. J., Kariuki, N. N., Park, J.-H., Wang, G., Baker, A. M., Macauley, N., Mukundan, R., More, K. L., & Neyerlin, K. C. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b11365 · Cited by 166
Self-citationEhelebe, K., Schmitt, N., Sievers, G. W., Jensen, A. W., Hrnjić, A., Jiménez, P. C., Kaiser, P., Geuß, M., Ku, Y.-P., Jovanovič, P., et al. (2022) · ACS Energy Letters · doi:10.1021/acsenergylett.1c02659 · Cited by 156
Van Cleve, T., Khandavalli, S., Chowdhury, A., Medina, S., Pylypenko, S., Wang, M., More, K. L., Kariuki, N., Myers, D. J., Weber, A. Z., et al. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b17614 · Cited by 148
Self-citationControlling cracking formation in fuel cell catalyst layers
Kumano, N., Kudo, K., Suda, A., Akimoto, Y., Ishii, M., & Nakamura, H. (2019) · Journal of Power Sources · doi:10.1016/j.jpowsour.2019.02.058 · Cited by 135
Volk, E. K., Kreider, M. E., Kwon, S., & Alia, S. M. (2023) · EES Catalysis · doi:10.1039/d3ey00193h · Cited by 135
Ionomer network of catalyst layers for proton exchange membrane fuel cell
Ren, H., Teng, Y., Meng, X., Fang, D., Huang, H., Geng, J., & Shao, Z. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.230186 · Cited by 125
Roll-to-roll production of catalyst coated membranes for low-temperature electrolyzers
Park, J., Kang, Z., Bender, G., Ulsh, M., & Mauger, S. A. (2020) · Journal of Power Sources · doi:10.1016/j.jpowsour.2020.228819 · Cited by 115
Self-citationYuan, X., Nayoze-Coynel, C., Shaigan, N., Fisher, D. C., Zhao, N., Zamel, N., Gazdzicki, P., Ulsh, M., Friedrich, K. A., Girard, F., et al. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.229540 · Cited by 118
Self-citationAnion Exchange Ionomers: Design Considerations and Recent Advances ‐ An Electrochemical Perspective
Favero, S., Stephens, I. E. L., & Titirici, M. (2023) · Advanced Materials · doi:10.1002/adma.202308238 · Cited by 120
Woo, S., Lee, S., Taning, A. Z., Yang, T., Park, S., & Yim, S. (2020) · Current Opinion in Electrochemistry · doi:10.1016/j.coelec.2020.03.006 · Cited by 97
Li, Y., Cleve, T. V., Sun, R., Gawas, R., Wang, G., Tang, M. H.-M., Elabd, Y. A., Snyder, J. D., & Neyerlin, K. C. (2020) · ACS Energy Letters · doi:10.1021/acsenergylett.0c00532 · Cited by 103
Self-citationOsmieri, L., Wang, G., Cetinbas, F. C., Khandavalli, S., Park, J. H., Medina, S., Mauger, S. A., Ulsh, M., Pylypenko, S., Myers, D. J., et al. (2020) · Nano Energy · doi:10.1016/j.nanoen.2020.104943 · Cited by 92
Self-citationDu, S., Li, W., Wu, H., Abel Chuang, P.-Y., Pan, M., & Sui, P.-C. (2020) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2020.07.241 · Cited by 88
Probing Ionomer Interactions with Electrocatalyst Particles in Solution
Berlinger, S. A., McCloskey, B. D., & Weber, A. Z. (2021) · ACS Energy Letters · doi:10.1021/acsenergylett.1c00866 · Cited by 93
Liu, H., Ney, L., Zamel, N., & Li, X. (2022) · Applied Sciences · doi:10.3390/app12083776 · Cited by 85
“To the best of our knowledge, most catalyst inks usually give a shear-thinning behavior [28,52,53,74]; only a few cases exhibit a nearly Newtonian behavior for shear rate of about 1~1000 s−1 [53,75].”
BackgroundInfluentialDevelopment of high-performance roll-to-roll-coated gas-diffusion-electrode-based fuel cells
Mauger, S. A., Wang, M., Cetinbas, F. C., Dzara, M. J., Park, J., Myers, D. J., Ahluwalia, R. K., Pylypenko, S., Hu, L., Litster, S., et al. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.230039 · Cited by 84
Self-citationKhandavalli, S., Park, J. H., Kariuki, N. N., Zaccarine, S. F., Pylypenko, S., Myers, D. J., Ulsh, M., & Mauger, S. A. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b14415 · Cited by 74
Self-citationDing, R. F., Yin, W., Cheng, G., Chen, Y., Wang, J., Wang, R., Rui, Z., Li, J., & Liu, J. (2021) · Energy and AI · doi:10.1016/j.egyai.2021.100098 · Cited by 79
Gong, Q., Li, C., Liu, Y., Ilavsky, J., Guo, F., Cheng, X., & Xie, J. (2021) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.1c06711 · Cited by 72
Creel, E. B., Tjiptowidjojo, K., Alex Lee, J., Livingston, K. M., Randall Schunk, P., Bell, N. S., Serov, A., & Wood III, D. L. (2022) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2021.11.047 · Cited by 67
Van Cleve, T., Wang, G., Mooney, M., Cetinbas, C. F., Kariuki, N., Park, J., Farghaly, A., Myers, D., & Neyerlin, K. C. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2020.228889 · Cited by 66
Self-citationRen, H., Meng, X., Lin, Y., & Shao, Z. (2022) · Journal of Energy Chemistry · doi:10.1016/j.jechem.2022.06.034 · Cited by 67
Guo, Y., Yang, D., Li, B., Yang, D., Ming, P., & Zhang, C. (2021) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.1c07070 · Cited by 65
Multicomponent, multiphase interactions in fuel-cell inks
Berlinger, S. A., Garg, S., & Weber, A. Z. (2021) · Current Opinion in Electrochemistry · doi:10.1016/j.coelec.2021.100744 · Cited by 72
Design of PEM water electrolysers with low iridium loading
Wang, C. R., Lee, K., Liu, C. P., Kulkarni, D. S., Atanassov, P. B., Peng, X., & Zenyuk, I. V. (2024) · International Materials Reviews · doi:10.1177/09506608231216665 · Cited by 72
Influence of ionomer adsorption on agglomerate structures in high-solid catalyst inks
Kumano, N., Kudo, K., Akimoto, Y., Ishii, M., & Nakamura, H. (2020) · Carbon · doi:10.1016/j.carbon.2020.07.047 · Cited by 61
Khandavalli, S., Iyer, R., Park, J. H., Myers, D. J., Neyerlin, K. C., Ulsh, M., & Mauger, S. A. (2020) · Langmuir · doi:10.1021/acs.langmuir.0c02015 · Cited by 56
Self-citationMurugaiah, D. K., & Shahgaldi, S. (2024) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2024.04.036 · Cited by 60
Ren, H., Meng, X., Lin, Y., & Shao, Z. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.230698 · Cited by 53
Wang, G., Osmieri, L., Star, A. G., Pfeilsticker, J., & Neyerlin, K. C. (2020) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ab7aa1 · Cited by 59
Self-citationDu, S., Guan, S., Mehrazi, S., Zhou, F., Pan, M., Zhang, R., Chuang, P. A., & Sui, P. (2021) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ac3598 · Cited by 53
Liu, P., Yang, D., Li, B., Zhang, C., & Ming, P. (2023) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2023.02.022 · Cited by 49
The impact of different side chain ionomer on membrane electrode assembly performance and durability
Liu, S., Lin, R., Lu, J., Wang, Y., & Cai, X. L. (2023) · Chemical Engineering Journal · doi:10.1016/j.cej.2023.145050 · Cited by 48
New insights on carbon black suspension rheology—Anisotropic thixotropy and antithixotropy
Wang, Y., & Ewoldt, R. H. (2022) · Journal of Rheology · doi:10.1122/8.0000455 · Cited by 53
Direct measurements of the microstructural origin of shear-thinning in carbon black suspensions
Hipp, J. B., Richards, J. J., & Wagner, N. J. (2021) · Journal of Rheology · doi:10.1122/8.0000089 · Cited by 50
Berlinger, S. A., Chowdhury, A., Cleve, T. V., He, A., Dagan, N., Neyerlin, K. C., McCloskey, B. D., Radke, C. J., & Weber, A. Z. (2022) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.2c10499 · Cited by 49
Self-citationImpact of Nonadsorbed Ionomer on Viscosity of Catalyst Inks for Polymer Electrolyte Fuel Cells
Yoshimune, W., & Harada, M. (2020) · Bulletin of the Chemical Society of Japan · doi:10.1246/bcsj.20190321 · Cited by 44
Li, J., Ma, Q., Dong, S., Zhao, S. Z., Wang, B., & Feng, X. (2025) · Chemical Society Reviews · doi:10.1039/d5cs00604j · Cited by 49
Li, B., Liu, Y., Guo, Y., Yang, D., Yang, D., Ming, P., & Zhang, C. (2021) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2021.06.216 · Cited by 44
Liu, P., Li, B., Yang, D., Zhang, C., & Ming, P. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.232427 · Cited by 42
Effect of rheological properties of catalyst slurry on the structure of catalyst layer in PEMFC
Yang, D., Guo, Y., Tang, H., Yang, D., Ming, P., Zhang, C., Li, B., & Zhu, S. (2022) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2021.12.227 · Cited by 40
On the state and stability of fuel cell catalyst inks
Bapat, S., Giehl, C., Kohsakowski, S., Peinecke, V., Schäffler, M., & Segets, D. (2021) · Advanced Powder Technology · doi:10.1016/j.apt.2021.08.030 · Cited by 38
Bapat, S., & Segets, D. (2020) · ACS Applied Nano Materials · doi:10.1021/acsanm.0c01467 · Cited by 37
Lee, S. A., Jun, S. E., Park, S. H., Kwon, K. C., Kang, J. H., Kwon, M. S., & Jang, H. W. (2023) · EES Catalysis · doi:10.1039/d3ey00165b · Cited by 40
Design of graded cathode catalyst layers with various ionomers for fuel cell application
Lyu, X., Cleve, T. V., Young, E., Li, J., Yu, H., Cullen, D. A., Neyerlin, K. C., & Serov, A. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.232530 · Cited by 38
Self-citationControl of Cluster Structures in Catalyst Inks by a Dispersion Medium
Yang, D., Zhu, S., Guo, Y., Tang, H., Yang, D., Zhang, C., Ming, P., & Li, B. (2021) · ACS Omega · doi:10.1021/acsomega.1c05026 · Cited by 37
Mehrazi, S., Sarker, M., Mojica, F., Rolfe, P., & Chuang, P. A. (2021) · Electrochimica Acta · doi:10.1016/j.electacta.2021.138690 · Cited by 35
Mahmood, Z., Garg, S., Yuan, Y., Xie, L. F., Wang, Y., & Waite, T. D. (2024) · Water Research · doi:10.1016/j.watres.2024.121410 · Cited by 34
Microstructure and macroscopic rheology of microporous layer nanoinks for PEM fuel cells
Pan, W., Chen, Z., Yao, D., Chen, X., Wang, F., & Dai, G. (2021) · Chemical Engineering Science · doi:10.1016/j.ces.2021.117001 · Cited by 33
Degradation of Platinum-Cobalt Alloy PEMFC Cathode Catalysts in Catalyst-Ionomer Inks
Myers, D. J., Kropf, A. J., Wegener, E. C., Mistry, H., Kariuki, N., & Park, J. (2021) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/abf4ab · Cited by 32
Self-citationYang, X. P., Li, X., Kong, Q., Liu, Z., Chen, J., Jia, H., Liu, Y., Xie, L., & Chen, C. (2019) · Science China Materials · doi:10.1007/s40843-019-1210-3 · Cited by 32
Lyu, X., Foster, J. G., Rice, R., Padgett, E., Creel, E. B., Li, J., Yu, H., Cullen, D. A., Kariuki, N. N., Park, J. H., et al. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.233503 · Cited by 32
Self-citationRole of the Ionomer in Supporting Electrolyte-Fed Anion Exchange Membrane Water Electrolyzers
Volk, E. K., Clauser, A. L., Kreider, M. E., Soetrisno, D. D., Khandavalli, S., Sugar, J. D., Kwon, S., & Alia, S. M. (2024) · ACS electrochemistry. · doi:10.1021/acselectrochem.4c00061 · Cited by 30
Self-citationMeyer, Q. P.-G., Liu, S., Ching, K., Wang, Y. D., & Zhao, C. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.232539 · Cited by 31
Yoshino, S., Harada, M., Hasegawa, N., & Jinnouchi, R. (2024) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2024.133847 · Cited by 30
Woo, S. H., Kim, S., Woo, S., Park, S., Kang, Y. S., Jung, N., & Yim, S. (2023) · Korean Journal of Chemical Engineering · doi:10.1007/s11814-023-1474-3 · Cited by 34
Khandavalli, S., Sharma‐Nene, N., Kabir, S., Sur, S., Rothstein, J. P., Neyerlin, K. C., Mauger, S. A., & Ulsh, M. (2021) · ACS Applied Polymer Materials · doi:10.1021/acsapm.0c01354 · Cited by 27
Self-citationThe state of art of nanocarbon black as analyte in a variety of matrices: A review
Sanjuan-Navarro, L., Moliner-Martínez, Y., & Campíns-Falcó, P. (2022) · TrAC Trends in Analytical Chemistry · doi:10.1016/j.trac.2022.116769 · Cited by 27
Mehrazi, S., Homayouni, T., Kakati, N., Sarker, M., Rolfe, P., & Chuang, P. A. (2024) · Applied Energy · doi:10.1016/j.apenergy.2024.122680 · Cited by 28
So, S., & Oh, K. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.232664 · Cited by 25
Baez-Cotto, C. M., Pfeilsticker, J., Godoy, A. O., Batool, M., Zaccarine, S. F., Wang, M., Bird, O. F., Pylypenko, S., Janković, J., Ulsh, M., et al. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.233567 · Cited by 25
Self-citationRen, H., Meng, X., Lin, Y., & Shao, Z. (2023) · Electrochimica Acta · doi:10.1016/j.electacta.2023.142710 · Cited by 25
Wang, M., Peng, F., Zou, J., Zhao, W. G., Wu, M., Williams, M. C., Yu, G., & Wang, H. (2025) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2025.115707 · Cited by 23
Saita, S., Takeda, S., & Kawasaki, H. (2022) · Nanomaterials · doi:10.3390/nano12122004 · Cited by 23
Jaster, T., Albers, S., Leonhard, A., Kräenbring, M., Lohmann, H., Zeidler‐Fandrich, B., Özcan, F., Segets, D., & Apfel, U. (2023) · Journal of Physics Energy · doi:10.1088/2515-7655/acb8db · Cited by 23
Liu, Q., & Richards, J. J. (2023) · Journal of Rheology · doi:10.1122/8.0000615 · Cited by 22
Temperature-induced shear-thinning in catalyst inks
Yoshimune, W., & Harada, M. (2021) · Electrochemistry Communications · doi:10.1016/j.elecom.2021.107099 · Cited by 22
The Impact of Hot-Press Conditions on the Durability of Polymer Electrolyte Membrane Fuel Cells
Wang, M., Taylor, A. K., Ochoa-Lozano, J., Medina, S., Pfeilsticker, J., Mauger, S. A., Pylypenko, S., Ulsh, M., & Bender, G. (2024) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2024.12.098 · Cited by 22
Self-citationMultiscale characterization of polymer electrolyte fuel cells elucidated by quantum beam analysis
Yoshimune, W. (2024) · Bulletin of the Chemical Society of Japan · doi:10.1093/bulcsj/uoae046 · Cited by 23
Advancements and challenges in printed thermoelectrics
Ma, H., Lu, T., Shi, X., Li, M., Huo, S., Song, P., Chen, Z., & Hong, M. (2025) · Progress in Materials Science · doi:10.1016/j.pmatsci.2025.101619 · Cited by 22
Lee, S., Woo, S. H., Pak, B., Kim, S., Kang, Y. S., Woo, S., Park, S., Yang, T.-H., & Yim, S. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.233644 · Cited by 21
Durable Fuel Cell Electrode Design via Efficient Distribution of the Acidic Ionomer
Ramaswamy, N., & Wortman, J. (2024) · ACS Energy Letters · doi:10.1021/acsenergylett.4c02704 · Cited by 23
Challenges of fabricating catalyst layers for PEM fuel cells using flatbed screen printing
Ney, L., Hog, J., Singh, R., Göttlicher, N., Schneider, P., Tepner, S., Klingele, M., Keding, R. J., Clement, F., & Groos, U. (2022) · Journal of Coatings Technology and Research · doi:10.1007/s11998-022-00710-1 · Cited by 21
Taning, A. Z., Lee, S., Woo, S., Park, S., Bae, B., & Yim, S. (2021) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ac2c13 · Cited by 18
Quarz, P., Zimmerer, N., Scharfer, P., & Schabel, W. (2024) · Fuel Cells · doi:10.1002/fuce.202300252 · Cited by 17
Khandavalli, S., Park, J., Rice, R., Zhang, D. Y., Berlinger, S. A., Bender, G., Myers, D. J., Ulsh, M., & Mauger, S. A. (2024) · Soft Matter · doi:10.1039/d4sm00987h · Cited by 17
Self-citationGuo, Y., Yang, D., Tang, H., Li, B., Yang, D., Ming, P., & Zhang, C. (2022) · Physics of Fluids · doi:10.1063/5.0102157 · Cited by 16
Wang, H., Osmieri, L., Yu, H., Zachman, M. J., Park, J. H., Kariuki, N. N., Cetinbas, F. C., Khandavalli, S., Mauger, S. A., Myers, D. J., et al. (2022) · SusMat · doi:10.1002/sus2.106 · Cited by 16
Self-citationZhou, Z., Yang, D., Guo, Y., & Li, B. (2022) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2022.09.242 · Cited by 16
Mehrazi, S., Sarker, M., & Chuang, P. A. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.233361 · Cited by 16
Screen Printing Catalyst Inks With Enhanced Process Stability for PEM Fuel Cell Production
Ney, L., Seidl, N., Singh, R., Schneider, P., Stross, D., Göppentin, A., Tepner, S., Klingele, M., & Keding, R. J. (2024) · Fuel Cells · doi:10.1002/fuce.202400158 · Cited by 16
Liu, P., Yang, D., Li, B., Kang, J., Zhang, C., Ming, P., Pan, X., & Liu, H. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.233817 · Cited by 13
Li, W., Bi, X., Luo, M., & Sui, P.-C. (2021) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/abe725 · Cited by 12
Yang, D., Guo, Y., Li, B., Yang, D., Ming, P., & Zhang, C. (2024) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2024.02.047 · Cited by 13
Harada, M., Kajiya, S., Mitsuoka, T., Takata, S.-I., Iwase, H., & Aoki, H. (2023) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2023.131183 · Cited by 12
Impact of a protic dimeric ionic liquid on PEM fuel cell performance and durability
Wang, L., Morales‐Collazo, O., Brennecke, J. F., & Jia, H. (2024) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2024.01.163 · Cited by 12
Nakajima, H., Ogura, T., Kato, Y., Kondo, N., Usukawa, R., Watanabe, R., Kobashi, K., & Okazaki, T. (2024) · Scientific Reports · doi:10.1038/s41598-024-68420-9 · Cited by 11
Longitudinal strand ordering leads to shear thinning in Nafion
Michelarakis, N., Franz, F., Gkagkas, K., & Gräter, F. (2021) · Physical Chemistry Chemical Physics · doi:10.1039/d1cp02024b · Cited by 11
Burghart, J., Ovarlez, G., & Medina‐González, Y. (2025) · Journal of Power Sources · doi:10.1016/j.jpowsour.2025.238497 · Cited by 10
Kariuki, N. N., Haug, A. T., Park, J. W., Lindell, M. J., & Myers, D. J. (2022) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ac94a4 · Cited by 11
Self-citationPei, Y., Zhu, W., Yue, R., Yao, J., Liu, X., Wang, L., Zhang, J., Yin, Y. S., & Guiver, M. D. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.232904 · Cited by 10
Coats, M. T., & Pylypenko, S. (2025) · ACS Applied Energy Materials · doi:10.1021/acsaem.5c01392 · Cited by 14
Do Melamine and Melamine-Formaldehyde Surface Modifiers Improve Fuel Cell Activity and Durability?
Ramaswamy, N., Kapushy, S., Mellott, N. P., LaLonde, A., Koestner, R. J., Coms, F. D., & Kumaraguru, S. (2023) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/acfbfb · Cited by 9
Xie, M., Chen, J., & Li, B. (2024) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2024.02.052 · Cited by 9
Choi, W.-J., Kang, I., Yu, D. M., Yoon, S. J., So, S., & Oh, K. (2024) · Korean Journal of Chemical Engineering · doi:10.1007/s11814-024-00221-2 · Cited by 10
Hamlyn, R. C. E., Mahl, J., Zhang, X., English, D., McAfee, T. R., & Crumlin, E. J. (2025) · Journal of Materials Chemistry A · doi:10.1039/d4ta07085b · Cited by 8
Metadata
- Authors
- Khandavalli, S., Park, J. H., Kariuki, N. N., Myers, D. J., Stickel, J. J., Hurst, K., Neyerlin, K. C., Ulsh, M., & Mauger, S. A.
- Affiliations
- National Laboratory of the Rockies (US)
- Argonne National Laboratory (US)
- Corresponding author
- Mauger, Scott A.
- ORCID
- Venue
- ACS Applied Materials & Interfaces
- Publisher
- American Chemical Society (ACS)
- Published
- 2018-12-10
- Volume
- 10
- Issue
- 50
- Pages
- 43610-43622
- ISSN
- 1944-8244 (ISSN-L)
- 1944-8252
- OpenAlex
- W2903943595
- Cited by
- 153
- References
- 65
- Citations by year
- 2026: 20 · 2025: 21 · 2024: 21 · 2023: 26 · 2022: 16 · 2021: 28 · 2020: 13 · 2019: 8
- FWCI
- 4.69
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- ACS Applied Materials & Interfaces (publishedVersion)
- PubMed (publishedVersion)
- OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information) (submittedVersion)
- Funders
- U.S. Department of Energy
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Chemical Engineering › Fluid Flow and Transfer Processes › Rheology and Fluid Dynamics Studies
- Keywords
- rheology, carbon black support, Nafion ionomer, ionomer-to-carbon ratio, high surface area carbon, Ketjen Black, Vulcan XC-72, viscosity, shear thinning, electrostatic stabilization, electrosteric stabilization, particle agglomeration, flocculation, dynamic light scattering
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.