Long-Term Strategies for Increased Recycling of Automotive Aluminum and Its Alloying Elements
The DOI matches its Crossref record; 26 of the 28 references it cites were found in a registry or an index.
Abstract
Aluminum recycling currently occurs in a cascading fashion, where some alloys, used in a limited number of applications, absorb most of the end-of-life scrap. An expected increase in scrap supply in coming decades necessitates restructuring of the aluminum cycle to open up new recycling paths for alloys and avoid a potential scrap surplus. This paper explores various interventions in end-of-life management and recycling of automotive aluminum, using a dynamic substance flow analysis model of aluminum and its alloying elements with resolution on component and alloy level (vehicle-component-alloy-element model). It was found that increased component dismantling before vehicle shredding can be an effective, so far underestimated, intervention in the medium term, especially if combined with development of safety-relevant components such as wheels from secondary material. In the long term, automatic alloy sorting technologies are most likely required, but could at the same time reduce the need for magnesium removal in refining. Cooperation between the primary and secondary aluminum industries, the automotive industry, and end-of-life vehicle dismantlers is therefore essential to ensure continued recycling of automotive aluminum and its alloying elements.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The check wasn’t confident either way, so it gives no verdict — never disputed.
In the citing paper
“| | | ↑50% metals fleet (Al replacing steel) [153, 154] | | | | → ↑fuel efficiency standards |”
From Material efficiency strategies to reducing greenhouse gas emissions associated with buildings, vehicles, and electronics—a review (2019) · cites this paper as [154]
Experimental — accuracy not yet measuredIn the citing paper
“Through alloy-specific recycling of the aluminum components, the additional energy use for producing aluminum components can be more than offset [154].”
From Material efficiency strategies to reducing greenhouse gas emissions associated with buildings, vehicles, and electronics—a review (2019) · cites this paper as [154]
In the citing paper
“| | | ↓50% Al in fleet [153, 154] | | | | |”
From Material efficiency strategies to reducing greenhouse gas emissions associated with buildings, vehicles, and electronics—a review (2019) · cites this paper as [154]
In the citing paper
“Light-weighting of passenger cars by material substitution can be a”
From Global Carbon Benefits of Material Substitution in Passenger Cars until 2050 and the Impact on the Steel and Aluminum Industries (2014) · cites this paper as [57]
Citations
Cites
Recent development in aluminium alloys for the automotive industry
Miller, W. S., Zhuang, L., Bottema, J., Wittebrood, A. J., De Smet, P., Haszler, A., & Vieregge, A. (2000) · Materials Science and Engineering: A · doi:10.1016/s0921-5093(99)00653-x · Cited by 2,498
Improving aluminum recycling: A survey of sorting and impurity removal technologies
Gaustad, G., Olivetti, E., & Kirchain, R. (2012) · Resources, Conservation and Recycling · doi:10.1016/j.resconrec.2011.10.010 · Cited by 412
Stock dynamics and emission pathways of the global aluminium cycle
Liu, G., Bangs, C. E., & Müller, D. B. (2013) · Nature Climate Change · doi:10.1038/nclimate1698 · Cited by 304
Self-citationThermodynamic Analysis of Contamination by Alloying Elements in Aluminum Recycling
Nakajima, K., Takeda, O., Miki, T., Matsubae, K., Nakamura, S., & Nagasaka, T. (2010) · Environmental Science & Technology · doi:10.1021/es9038769 · Cited by 168
Centennial Evolution of Aluminum In-Use Stocks on Our Aluminized Planet
Liu, G., & Müller, D. B. (2013) · Environmental Science & Technology · doi:10.1021/es305108p · Cited by 144
Self-citationHatayama, H., Daigo, I., Matsuno, Y., & Adachi, Y. (2012) · Resources Conservation and Recycling · doi:10.1016/j.resconrec.2012.06.006 · Cited by 139
The role of automobiles for the future of aluminum recycling
Modaresi, R., & Müller, D. B. (2012) · Environmental Science & Technology · doi:10.1021/es300648w · Cited by 138
Self-citationBriskham, P., Blundell, N., Li, H., Hewitt, R., Young, K. W., & Boomer, D. R. (2006) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2006-01-0774 · Cited by 113
Stock dynamics and emission pathways of the global aluminum cycle
Müller, D. B., Liu, G., & Bangs, C. E. (2013) · Springer eBooks · doi:10.1007/978-3-319-48763-2_19 · Cited by 108
Self-citationThe development of recycle-friendly automotive aluminum alloys
Das, S. K., Green, J. A. S., & Kaufman, J. G. (2007) · JOM · doi:10.1007/s11837-007-0140-2 · Cited by 89
Research works printed but not linked: 9
- International Aluminium Institute, 2011, Global Aluminium Recycling Committee, Global Aluminium Recycling Model (GARC)
- Rombach, G.,Future availability of aluminium scrap. InLight Metals, Proceedings of the 131st TMS Annual Meeting;Schneider, W. A., Ed. Seattle, WA, 2002; pp1011–1018.
- Das, S.; Green, J.,The recycling of aluminum from building and construction applications. InLight Metals, Proceedings of the 137th TMS Annual Meeting & Exhibition,DeYoung, D. H., Ed.; New Orleans, LA, 2008; pp1113–1118.
- Gesing, A.; Harbeck, H.,Particle sorting of light-metal alloys and expanded use of manufacturing scrap in automotive, marine and aerospace markets. InProceedings of REWAS 2008, Global Symposium on Recycling, Waste Treatment and Clean Technology,Mishra, B.; Ludwig, C.; Das, S., Eds.; Cancun, Mexico, 2008.
- Furrer P., 2003, SAE Technical paper series, 2003, 319
- Altenpohl D., 1998, Aluminum: Technology, Applications, and Environment: a Profile of a Modern Metal
- Briskham P., 2006, SAE Tech. Pap. Ser., 2006
- Verbrugge M. W., 2010, Light Metals, Proceedings of the technical sessions presented by the TMS Aluminium Committee at the TMS 2010 Annual Meeting & Exhibition
- Fragner W., 2014, Light Metals 2014
Cited by
Items 101–147 of 147
Maps of the physical economy to inform sustainability strategies
Müller, D. B., Billy, R. G., Simoni, M. U., Petavratzi, E., Liu, G., Rechberger, H., & Cullen, J. M. (2024) · Elsevier eBooks · doi:10.1016/b978-0-323-85514-3.00038-5 · Cited by 4
Self-citationBuchner, H., Laner, D., Rechberger, H., & Fellner, J. (2014) · Metallurgical Research & Technology · doi:10.1051/metal/2014040 · Cited by 4
Heidari, S. M., Zhu, Y., Tsai, A., Keoleian, G. A., Kim, H. C., Kleine, R. D. D., Kelly, J. C., Shukla, S., & Cooper, D. R. (2025) · SSRN Electronic Journal · doi:10.2139/ssrn.5279786 · Cited by 3
Reichert, D., Maeder, M., & Fröhling, M. (2025) · Resources Conservation and Recycling · doi:10.1016/j.resconrec.2025.108266 · Cited by 3
Kaya, Ö., Demir, F., Çolak, B., Yaşlak, A., Kahruman, C., Kocabaş, M., & Uludağ, M. (2026) · International Journal of Metalcasting · doi:10.1007/s40962-026-01935-1 · Cited by 3
Nunomura, J., Matsushima, H., Kyo, Y., Kojima, Y., & Ueda, M. (2023) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ad0ea3 · Cited by 3
Enhanced Processing of Aluminum Scrap at End‐of‐Life via Artificial Intelligence & Smart Sensing
Langan, S. M., Molstad, E., Longo, B. A., Ralphs, C. J., Saro, R. D., Apelian, D., & Kelly, S. (2024) · Wiley eBooks · doi:10.1002/9781394214297.ch11 · Cited by 3
Peeratatsuwan, C., Suwittayaruk, P., Mayai, A., Petcharatip, K., Tungkasiri, U., Pramuanjaroenkij, A., & Chowwanonthapunya, T. (2024) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-024-10522-6 · Cited by 2
Shah, K. U., & Kunlere, I. O. (2025) · Cleaner Waste Systems · doi:10.1016/j.clwas.2025.100313 · Cited by 2
Samberger, S., Weißensteiner, I., Tunes, M. A., Stemper, L., Kainz, C., Morak, R., Uggowitzer, P. J., & Pogatscher, S. (2025) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2025.06.106 · Cited by 2
Comparison of Degassing Efficiency on a Foundry Degassing Unit Using Different Rotor Types
Kolínský, J., Prášil, T., Socha, L., SVIŽELOVÁ, J., Gryc, K., Häusler, J., & Dvořák, M. (2024) · Applied Sciences · doi:10.3390/app14052216 · Cited by 2
Microstructure and Properties of 6 Series Aluminum Alloy Under Different Aging Treatment Systems
Yin, Q., Jiang, L., Fengjia, G. U. O., & Zhaoxia, W. A. N. G. (2023) · Materials Science · doi:10.5755/j02.ms.32988 · Cited by 2
Rosa, P., & Terzi, S. (2023) · IFIP advances in information and communication technology · doi:10.1007/978-3-031-25182-5_8 · Cited by 2
Albizzati, P. F., Walker, A. M., Milios, L., Besler, M., Piñero Mira, P., Pedauga, L., Donati, F., Marten, C., Baldassarre, B., & Tonini, D. (2025) · Leiden Repository (Leiden University) · doi:10.2760/5505344 · Cited by 2
Pomerleau, A., Lafaye, P., Brochu, M., & Harvey, J.-P. (2026) · The minerals, metals & materials series · doi:10.1007/978-3-032-13832-3_153 · Cited by 1
Formability comparison of recycled and primary AA6082 alloy exposed to different heat treatments
Moon, C., & Welo, T. (2026) · Advances in Mechanical Engineering · doi:10.1177/16878132261444894 · Cited by 1
Investigating the Potential of Secondary Aluminum Cast Alloys Used as Wrought Alloys
Krall, P., & Pogatscher, S. (2024) · The minerals, metals & materials series · doi:10.1007/978-3-031-50308-5_24 · Cited by 1
Influence of Solidification Rate and Impurity Content on 5/7-Crossover Alloys
Samberger, S., Stemper, L., Uggowitzer, P. J., Tosone, R., & Pogatscher, S. (2024) · The minerals, metals & materials series · doi:10.1007/978-3-031-50308-5_28 · Cited by 1
Transformations towards zero-carbon development pathways
Nakićenović, N., & Wilson, C. G. (2019) · IIASA PURE (International Institute of Applied Systems Analysis) · Cited by 1
Nakamura, S. (2023) · Springer eBooks · doi:10.1007/978-3-031-43684-0_7 · Cited by 1
Assuad, C. S. A., Øien, C. D., & Ringen, G. (2023) · Procedia CIRP · doi:10.1016/j.procir.2023.09.079 · Cited by 1
Preliminary Work Towards A Cross Lifecycle Design Tool for Increased High‐Quality Metal Recycling
Cooper, D., Hamid, A., Heidari, S. M., Tsai, A., & Zhu, Y. (2024) · Wiley eBooks · doi:10.1002/9781394214297.ch16 · Cited by 1
Gutschi, A. (2022) · reposiTUm (TU Wien) · doi:10.34726/hss.2022.103447 · Cited by 3
Hua, N. (2020) · Deep Blue (University of Michigan)
(2016) · CRC Press eBooks · doi:10.1201/9781315313450-6
Hurdle Appraisal for the Implementation of Circular Economy Notions in Supply Chain
Gupta, R., Tyagi, M., & Garg, R. K. (2022) · Lecture notes in mechanical engineering · doi:10.1007/978-981-16-7059-6_3
OVERVIEW OF TECHNOLOGIES AND METHODS FOR SORTING AND CLASSIFYING END-OF-LIFE ALUMINUM
Скуйбіда, О. (2023) · Collection of Scientific Publications NUS · doi:10.15589/znp2023.1(490).7
Roca‐Puigròs, M., Gerber, A., Ulrich, M. M., Reich, M. Y., Müller, D. B., & Wäger, P. A. (2024) · Journal of Industrial Ecology · doi:10.1111/jiec.13462
Self-citationBayazid, S. M., González, A., Lombardi, A., Byczynski, G. E., Shankar, S., & Kish, J. R. (2024) · Springer eBooks · doi:10.1007/978-3-031-67398-6_92
The LISA project: opportunities and challenges of recycling automotive heat exchangers
Lattanzi, L., Liljenfors, T., Westergård, R., & Windmark, C. (2024) · Matériaux & Techniques · doi:10.1051/mattech/2024027
Samberger, S., Weißensteiner, I., Tunes, M. A., Stemper, L., Kainz, C., Morak, R., Uggowitzer, P. J., & Pogatscher, S. (2025) · SSRN Electronic Journal · doi:10.2139/ssrn.5151309
Enhancing Secondary Aluminium Supply: Optimising Urban Mining Through a Systems Thinking Approach
Liu, M., Schneider, K., Litos, L., & Salonitis, K. (2025) · The minerals, metals & materials series · doi:10.1007/978-3-031-80676-6_158
Bhuiyan, M. S. H., Ahmed, G., Soun, M. M., Khan, S., Eva, S. A., Al‐Humaidi, J. Y., Batterjee, M. G., Rahman, M. M., & Karim, M. R. (2025) · Waste Management & Research The Journal for a Sustainable Circular Economy · doi:10.1177/0734242x251376871
Tsai, A., Zhu, Y., Heidari, S. M., & Cooper, D. (2026) · Journal of Industrial Ecology · doi:10.1007/s44498-026-00119-8
Scholz, A., Proff, S., Welter, C., & Zeiss, C. (2024) · Publication Server of the Wuppertal Institute (Wuppertal Institute) · doi:10.48506/opus-8677
Pedneault, J. (2022) · PolyPublie (École Polytechnique de Montréal)
Cinkilic, E. (2019) · OhioLink ETD Center (Ohio Library and Information Network) · Cited by 2
Resource modelling in a circular economy context
Helander, H. (2023) · Chalmers Research (Chalmers University of Technology)
Thermodynamic assessment of raw material use in passenger vehicles
Ortego Bielsa, A., VALERO DELGADO, A., & VALERO CAPILLA, A. F. (2019) · Zaguan (Universidad de Zaragoza) · Cited by 3
Electrochemical Behavior of Mg Ions in AlCl3-NaCl-KCl Molten Salt
HIROSE, S., Miyashita, T., Matsushima, H., & Ueda, M. (2026) · Electrochemistry · doi:10.5796/electrochemistry.25-00162
Delporte, M. (2022) · theses.fr (ABES) · doi:10.70675/c60d2699z8524z49e5z993dzcea2a2d0428d
Sustainability of battery electric vehicles
Gohari, S., Yay, A. S. E., Zheng, Y., Sorouri, H., & Oshnoei, A. (2026) · Elsevier eBooks · doi:10.1016/b978-0-443-29210-1.00143-6
Junoh, H., Mohamed, H., Aziz, N. A. M., Yu, K. L., Zainal, B. S., Ong, H. C., Ker, P. J., Awang, N., Mahlia, T. M. I., Othman, F. E. C., et al. (2026) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2026.117282
Dynamic Production Planning Under Escalating Circularity Mandates with Finite Material RecyclabilityPreprint
Dimitrov, S., Schlößer, R., Chenavaz, R. Y., & FIGGE, F. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6470878
How circular economy reshapes aluminum demand and carbon emissions in the Chinese automotive sector
Chen, J., Zhang, Y. W., Zheng, Y., Geng, Y., Hao, H., Xue, Y., & Fu, Z. (2026) · Resources Conservation and Recycling · doi:10.1016/j.resconrec.2026.109155
Suhandeniputri, D. J., Balogh, P., Vincze, A., Pekk, L., & Németh, K. (2026) · Future Transportation · doi:10.3390/futuretransp6050224
Selective silicon removal from AlSi scraps by Mg-assisted electromagnetic fractional crystallization
Yang, B., Friedrich, S., & Friedrich, B. G. (2026) · Separation and Purification Technology · doi:10.1016/j.seppur.2026.140736
Metadata
- Authors
- Løvik, A. N., Modaresi, R., & Müller, D. B.
- Affiliations
- Norwegian University of Science and Technology (NO)
- Corresponding author
- Løvik, Amund N.
- Müller, Daniel B.
- Venue
- Environmental Science & Technology
- Publisher
- American Chemical Society (ACS)
- Published
- 2014-04-02
- Volume
- 48
- Issue
- 8
- Pages
- 4257-4265
- ISSN
- 0013-936X (ISSN-L)
- 1520-5851
- OpenAlex
- W2323688192
- Cited by
- 136
- References
- 28
- Citations by year
- 2026: 10 · 2025: 16 · 2024: 16 · 2023: 18 · 2022: 17 · 2021: 4 · 2020: 10 · 2019: 11 · 2018: 10 · 2017: 9 · 2016: 7 · 2015: 4 · 2014: 3
- FWCI
- 12.43
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Environmental Science & Technology (publishedVersion)
- PubMed (publishedVersion)
- Topics
- Physical Sciences › Environmental Science › Waste Management and Disposal › Recycling and Waste Management Techniques
- Physical Sciences › Materials Science › Metals and Alloys › Extraction and Separation Processes
- Physical Sciences › Environmental Science › Waste Management and Disposal › Municipal Solid Waste Management
- Keywords
- end-of-life vehicles, alloying elements, magnesium removal, recycled aluminum, recycling pathway
- MeSH terms
- Alloys, Aluminum, Automobiles, Computer Simulation, Time Factors, Recycling
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.