Long-Term Strategies for Increased Recycling of Automotive Aluminum and Its Alloying Elements
The DOI matches its Crossref record; 26 of the 28 references it cites were found in a registry or an index.
Abstract
Aluminum recycling currently occurs in a cascading fashion, where some alloys, used in a limited number of applications, absorb most of the end-of-life scrap. An expected increase in scrap supply in coming decades necessitates restructuring of the aluminum cycle to open up new recycling paths for alloys and avoid a potential scrap surplus. This paper explores various interventions in end-of-life management and recycling of automotive aluminum, using a dynamic substance flow analysis model of aluminum and its alloying elements with resolution on component and alloy level (vehicle-component-alloy-element model). It was found that increased component dismantling before vehicle shredding can be an effective, so far underestimated, intervention in the medium term, especially if combined with development of safety-relevant components such as wheels from secondary material. In the long term, automatic alloy sorting technologies are most likely required, but could at the same time reduce the need for magnesium removal in refining. Cooperation between the primary and secondary aluminum industries, the automotive industry, and end-of-life vehicle dismantlers is therefore essential to ensure continued recycling of automotive aluminum and its alloying elements.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The check wasn’t confident either way, so it gives no verdict — never disputed.
In the citing paper
“| | | ↑50% metals fleet (Al replacing steel) [153, 154] | | | | → ↑fuel efficiency standards |”
From Material efficiency strategies to reducing greenhouse gas emissions associated with buildings, vehicles, and electronics—a review (2019) · cites this paper as [154]
Experimental — accuracy not yet measuredIn the citing paper
“Through alloy-specific recycling of the aluminum components, the additional energy use for producing aluminum components can be more than offset [154].”
From Material efficiency strategies to reducing greenhouse gas emissions associated with buildings, vehicles, and electronics—a review (2019) · cites this paper as [154]
In the citing paper
“| | | ↓50% Al in fleet [153, 154] | | | | |”
From Material efficiency strategies to reducing greenhouse gas emissions associated with buildings, vehicles, and electronics—a review (2019) · cites this paper as [154]
In the citing paper
“Light-weighting of passenger cars by material substitution can be a”
From Global Carbon Benefits of Material Substitution in Passenger Cars until 2050 and the Impact on the Steel and Aluminum Industries (2014) · cites this paper as [57]
Citations
Cites
Recent development in aluminium alloys for the automotive industry
Miller, W. S., Zhuang, L., Bottema, J., Wittebrood, A. J., De Smet, P., Haszler, A., & Vieregge, A. (2000) · Materials Science and Engineering: A · doi:10.1016/s0921-5093(99)00653-x · Cited by 2,498
Improving aluminum recycling: A survey of sorting and impurity removal technologies
Gaustad, G., Olivetti, E., & Kirchain, R. (2012) · Resources, Conservation and Recycling · doi:10.1016/j.resconrec.2011.10.010 · Cited by 412
Stock dynamics and emission pathways of the global aluminium cycle
Liu, G., Bangs, C. E., & Müller, D. B. (2013) · Nature Climate Change · doi:10.1038/nclimate1698 · Cited by 304
Self-citationThermodynamic Analysis of Contamination by Alloying Elements in Aluminum Recycling
Nakajima, K., Takeda, O., Miki, T., Matsubae, K., Nakamura, S., & Nagasaka, T. (2010) · Environmental Science & Technology · doi:10.1021/es9038769 · Cited by 168
Centennial Evolution of Aluminum In-Use Stocks on Our Aluminized Planet
Liu, G., & Müller, D. B. (2013) · Environmental Science & Technology · doi:10.1021/es305108p · Cited by 144
Self-citationHatayama, H., Daigo, I., Matsuno, Y., & Adachi, Y. (2012) · Resources Conservation and Recycling · doi:10.1016/j.resconrec.2012.06.006 · Cited by 139
The role of automobiles for the future of aluminum recycling
Modaresi, R., & Müller, D. B. (2012) · Environmental Science & Technology · doi:10.1021/es300648w · Cited by 138
Self-citationBriskham, P., Blundell, N., Li, H., Hewitt, R., Young, K. W., & Boomer, D. R. (2006) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2006-01-0774 · Cited by 113
Stock dynamics and emission pathways of the global aluminum cycle
Müller, D. B., Liu, G., & Bangs, C. E. (2013) · Springer eBooks · doi:10.1007/978-3-319-48763-2_19 · Cited by 108
Self-citationThe development of recycle-friendly automotive aluminum alloys
Das, S. K., Green, J. A. S., & Kaufman, J. G. (2007) · JOM · doi:10.1007/s11837-007-0140-2 · Cited by 89
Werheit, P., Fricke-Begemann, C., Gesing, M., & Noll, R. (2011) · Journal of Analytical Atomic Spectrometry · doi:10.1039/c1ja10096c · Cited by 86
End-of-life vehicle recycling : state of the art of resource recovery from shredder residue.
Jody, B. J., Daniels, E. J., Duranceau, C. M., Pomykala, J. A., & Spangenberger, J. S. (2011) · doi:10.2172/1010492 · Cited by 84
Assessment of the Recycling Potential of Aluminum in Japan, the United States, Europe and China
Hatayama, H., Daigo, I., Matsuno, Y., & Adachi, Y. (2009) · MATERIALS TRANSACTIONS · doi:10.2320/matertrans.mra2008337 · Cited by 82
Recycling light metals from end-of-life vehicle
Gesing, A. J., & Wolanski, R. (2001) · JOM · doi:10.1007/s11837-001-0188-3 · Cited by 71
Component- and Alloy-Specific Modeling for Evaluating Aluminum Recycling Strategies for Vehicles
Modaresi, R., Løvik, A. N., & Müller, D. B. (2014) · JOM · doi:10.1007/s11837-014-0900-8 · Cited by 62
Self-citationModelling More Sustainable Aluminium (4 pp)
Martchek, K. J. (2005) · The International Journal of Life Cycle Assessment · doi:10.1065/lca2006.01.231 · Cited by 57
Gaustad, G., Olivetti, E., & Kirchain, R. (2011) · Environmental Science & Technology · doi:10.1021/es103508u · Cited by 50
Provision of LCI data in the European aluminium industry Methods and examples
Leroy, C. (2009) · The International Journal of Life Cycle Assessment · doi:10.1007/s11367-009-0068-6 · Cited by 40
Short-run demand and supply elasticities in the West European market for secondary aluminium
Blomberg, J., & Hellmer, S. (2000) · Resources Policy · doi:10.1016/s0301-4207(00)00015-5 · Cited by 38
Recycling of aluminium scrap for secondary Al-Si alloys
Velasco, E., & Nino, J. (2010) · Waste Management & Research The Journal for a Sustainable Circular Economy · doi:10.1177/0734242x10381413 · Cited by 35
Proceedings of European Metallurgical Conference EMC 2013
Kaindl, M., Poscher, A., Luidold, S., & Antrekowitsch, H. (2013) · Cited by 24
Solidification studies of automotive heat exchanger materials
Carlberg, T., Jaradeh, M., & Kamaga, H. K. (2006) · JOM · doi:10.1007/s11837-006-0228-0 · Cited by 13
Formability Evaluation of Recycle-Friendly Automotive Aluminum Alloys
Das, S. K., Yin, W., Wen, X., Liu, Y., & Ningileri, S. (2008) · SAE International Journal of Materials and Manufacturing · doi:10.4271/2008-01-1095 · Cited by 12
Recycling end-of-life vehicles of the future. Final CRADA report.
Jody, B. J., Pomykala, J. A., Spangenberger, J. S., & Daniels, E. (2010) · doi:10.2172/970800 · Cited by 10
Using Scrap in Recycling Alloys for Structural Applications in The Automotive Industry
Fragner, W., Baumgartner, K., Suppan, H., Hummel, M., Bösch, D., Höppel, H. W., & Uggowitzer, P. J. (2014) · Springer eBooks · doi:10.1007/978-3-319-48144-9_59 · Cited by 4
Furrer, P., Jones, R. F., & Ruckstuhl, B. (2003) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2003-01-2771 · Cited by 1
Research works printed but not linked: 9
- International Aluminium Institute, 2011, Global Aluminium Recycling Committee, Global Aluminium Recycling Model (GARC)
- Rombach, G.,Future availability of aluminium scrap. InLight Metals, Proceedings of the 131st TMS Annual Meeting;Schneider, W. A., Ed. Seattle, WA, 2002; pp1011–1018.
- Das, S.; Green, J.,The recycling of aluminum from building and construction applications. InLight Metals, Proceedings of the 137th TMS Annual Meeting & Exhibition,DeYoung, D. H., Ed.; New Orleans, LA, 2008; pp1113–1118.
- Gesing, A.; Harbeck, H.,Particle sorting of light-metal alloys and expanded use of manufacturing scrap in automotive, marine and aerospace markets. InProceedings of REWAS 2008, Global Symposium on Recycling, Waste Treatment and Clean Technology,Mishra, B.; Ludwig, C.; Das, S., Eds.; Cancun, Mexico, 2008.
- Furrer P., 2003, SAE Technical paper series, 2003, 319
- Altenpohl D., 1998, Aluminum: Technology, Applications, and Environment: a Profile of a Modern Metal
- Briskham P., 2006, SAE Tech. Pap. Ser., 2006
- Verbrugge M. W., 2010, Light Metals, Proceedings of the technical sessions presented by the TMS Aluminium Committee at the TMS 2010 Annual Meeting & Exhibition
- Fragner W., 2014, Light Metals 2014
Cited by
Making sustainable aluminum by recycling scrap: The science of “dirty” alloys
Raabe, D., Ponge, D., Uggowitzer, P. J., Roscher, M., Paolantonio, M., Liu, C., Antrekowitsch, H., Kozeschnik, E., Seidmann, D., Gault, B., et al. (2022) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.100947 · Cited by 626
Pauliuk, S. (2018) · Resources, Conservation and Recycling · doi:10.1016/j.resconrec.2017.10.019 · Cited by 554
Hertwich, E. G., Ali, S., Ciacci, L., Fishman, T., Heeren, N., Masanet, E., Asghari, F. N., Olivetti, E., Pauliuk, S., Tu, Q., et al. (2019) · Environmental Research Letters · doi:10.1088/1748-9326/ab0fe3 · Cited by 477
Solid Waste and the Circular Economy: A Global Analysis of Waste Treatment and Waste Footprints
Tisserant, A., Pauliuk, S., Merciai, S., Schmidt, J., Fry, J., Wood, R., & Tukker, A. (2017) · Journal of Industrial Ecology · doi:10.1111/jiec.12562 · Cited by 376
Czerwinski, F. (2020) · Journal of Materials Science · doi:10.1007/s10853-019-03892-z · Cited by 244
Metadata
- Authors
- Løvik, A. N., Modaresi, R., & Müller, D. B.
- Affiliations
- Norwegian University of Science and Technology (NO)
- Corresponding author
- Løvik, Amund N.
- Müller, Daniel B.
- Venue
- Environmental Science & Technology
- Publisher
- American Chemical Society (ACS)
- Published
- 2014-04-02
- Volume
- 48
- Issue
- 8
- Pages
- 4257-4265
- ISSN
- 0013-936X (ISSN-L)
- 1520-5851
- OpenAlex
- W2323688192
- Cited by
- 136
- References
- 28
- Citations by year
- 2026: 10 · 2025: 16 · 2024: 16 · 2023: 18 · 2022: 17 · 2021: 4 · 2020: 10 · 2019: 11 · 2018: 10 · 2017: 9 · 2016: 7 · 2015: 4 · 2014: 3
- FWCI
- 12.43
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Environmental Science & Technology (publishedVersion)
- PubMed (publishedVersion)
- Topics
- Physical Sciences › Environmental Science › Waste Management and Disposal › Recycling and Waste Management Techniques
- Physical Sciences › Materials Science › Metals and Alloys › Extraction and Separation Processes
- Physical Sciences › Environmental Science › Waste Management and Disposal › Municipal Solid Waste Management
- Keywords
- end-of-life vehicles, alloying elements, magnesium removal, recycled aluminum, recycling pathway
- MeSH terms
- Alloys, Aluminum, Automobiles, Computer Simulation, Time Factors, Recycling
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.