The DOI matches its Crossref record; 52 of the 52 references it cites were found in a registry or an index.
Methane Storage in Metal–Organic Frameworks: Current Records, Surprise Findings, and Challenges
Abstract
We have examined the methane uptake properties of six of the most promising metal organic framework (MOF) materials: PCN-14, UTSA-20, HKUST-1, Ni-MOF-74 (Ni-CPO-27), NU-111, and NU-125. We discovered that HKUST-1, a material that is commercially available in gram scale, exhibits a room-temperature volumetric methane uptake that exceeds any value reported to date. The total uptake is about 230 cc(STP)/cc at 35 bar and 270 cc(STP)/cc at 65 bar, which meets the new volumetric target recently set by the Department of Energy (DOE) if the packing efficiency loss is ignored. We emphasize that MOFs with high surface areas and pore volumes perform better overall. NU-111, for example, reaches ~75% of both the gravimetric and the volumetric targets. We find that values for gravimetric uptake, pore volume, and inverse density of the MOFs we studied scale essentially linearly with surface area. From this linear dependence, we estimate that a MOF with surface area 7500 m(2)/g and pore volume 3.2 cc/g could reach the current DOE gravimetric target of 0.5 g/g while simultaneously exhibiting around ~200 cc/cc volumetric uptake. We note that while values for volumetric uptake are based on ideal single crystal densities, in reality the packing densities of MOFs are much lower. Finally, we show that compacting HKUST-1 into wafer shapes partially collapses the framework, decreasing both volumetric and gravimetric uptake significantly. Hence, one of the important challenges going forward is to find ways to pack MOFs efficiently without serious damage or to synthesize MOFs that can withstand substantial mechanical pressure.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Reticular synthesis and the design of new materials
Yaghi, O. M., O'Keeffe, M., Ockwig, N. W., Chae, H. K., Eddaoudi, M., & Kim, J. (2003) · Nature · doi:10.1038/nature01650 · Cited by 9,101
Carbon Dioxide Capture in Metal–Organic Frameworks
Sumida, K., Rogow, D. L., Mason, J. A., McDonald, T. M., Bloch, E. D., Herm, Z. R., Bae, T.-H., & Long, J. R. (2012) · Chemical Reviews · doi:10.1021/cr2003272 · Cited by 6,408
Metal–Organic Frameworks for Separations
Li, J.-R., Sculley, J., & Zhou, H.-C. (2012) · Chemical Reviews · doi:10.1021/cr200190s · Cited by 6,323
A Chemically Functionalizable Nanoporous Material [Cu 3 (TMA) 2 (H 2 O) 3 ] n
Chui, S. S.-Y., Lo, S. M.-F., Charmant, J. P. H., Orpen, A. G., & Williams, I. D. (1999) · Science · doi:10.1126/science.283.5405.1148 · Cited by 6,063
Hybrid porous solids: past, present, future
Férey, G. (2008) · Chem. Soc. Rev. · doi:10.1039/b618320b · Cited by 5,822
Carbon Dioxide Capture: Prospects for New Materials
D'Alessandro, D. M., Smit, B., & Long, J. R. (2010) · Angewandte Chemie International Edition · doi:10.1002/anie.201000431 · Cited by 4,046
Ultrahigh Porosity in Metal-Organic Frameworks
Furukawa, H., Ko, N., Go, Y. B., Aratani, N., Choi, S. B., Choi, E., Yazaydin, A. Ö., Snurr, R. Q., O’Keeffe, M., Kim, J., et al. (2010) · Science · doi:10.1126/science.1192160 · Cited by 3,904
Hydrogen Storage in Metal–Organic Frameworks
Suh, M. P., Park, H. J., Prasad, T. K., & Lim, D.-W. (2012) · Chemical Reviews · doi:10.1021/cr200274s · Cited by 3,689
Horike, S., Shimomura, S., & Kitagawa, S. (2009) · Nature Chemistry · doi:10.1038/nchem.444 · Cited by 2,486
Metal–Organic Framework Materials with Ultrahigh Surface Areas: Is the Sky the Limit?
Farha, O. K., Eryazici, I., Jeong, N. C., Hauser, B. G., Wilmer, C. E., Sarjeant, A. A., Snurr, R. Q., Nguyen, S. T., Yazaydın, A. Ö., & Hupp, J. T. (2012) · Journal of the American Chemical Society · doi:10.1021/ja3055639 · Cited by 1,958
Self-citation
Cited by
Pore chemistry and size control in hybrid porous materials for acetylene capture from ethylene
Cui, X., Chen, K., Xing, H., Yang, Q., Krishna, R., Bao, Z., Wu, H., Zhou, W., Dong, X., Han, Y., et al. (2016) · Science · doi:10.1126/science.aaf2458 · Cited by 1,449
Evaluating metal–organic frameworks for natural gas storage
Mason, J. A., Veenstra, M., & Long, J. R. (2014) · Chem. Sci. · doi:10.1039/c3sc52633j · Cited by 1,239
Methane storage in flexible metal–organic frameworks with intrinsic thermal management
Mason, J. A., Oktawiec, J., Taylor, M. K., Hudson, M. R., Rodriguez, J., Bachman, J. E., Gonzalez, M. I., Cervellino, A., Guagliardi, A., Brown, C. M., et al. (2015) · Nature · doi:10.1038/nature15732 · Cited by 1,076
CO2 Capture and Separations Using MOFs: Computational and Experimental Studies
Yu, J., Xie, L.-H., Li, J.-R., Ma, Y., Seminario, J. M., & Balbuena, P. B. (2017) · Chemical Reviews · doi:10.1021/acs.chemrev.6b00626 · Cited by 1,047
Catalysis by Metal Organic Frameworks: Perspective and Suggestions for Future Research
Yang, D., & Gates, B. C. (2019) · ACS Catalysis · doi:10.1021/acscatal.8b04515 · Cited by 932
Kökçam-Demir, Ü., Goldman, A., Esrafili, L., Gharib, M., Morsali, A., Weingart, O., & Janiak, C. (2020) · Chemical Society Reviews · doi:10.1039/c9cs00609e · Cited by 895
Porous metal-organic frameworks for gas storage and separation: Status and challenges
Li, H., Li, L., Lin, R.-B., Zhou, W., Zhang, Z., Xiang, S., & Chen, B. (2019) · EnergyChem · doi:10.1016/j.enchem.2019.100006 · Cited by 891
Metal–organic frameworks based on flexible ligands (FL-MOFs): structures and applications
Lin, Z.-J., Lü, J., Hong, M., & Cao, R. (2014) · Chem. Soc. Rev. · doi:10.1039/c3cs60483g · Cited by 874
Best Practices for the Synthesis, Activation, and Characterization of Metal–Organic Frameworks
Howarth, A. J., Peters, A. W., Vermeulen, N. A., Wang, T. C., Hupp, J. T., & Farha, O. K. (2017) · Chemistry of Materials · doi:10.1021/acs.chemmater.6b02626 · Cited by 746
Self-citationA review of solidified natural gas (SNG) technology for gas storage via clathrate hydrates
Veluswamy, H. P., Kumar, A., Seo, Y., Lee, J. D., & Linga, P. (2018) · Applied Energy · doi:10.1016/j.apenergy.2018.02.059 · Cited by 656
A sol–gel monolithic metal–organic framework with enhanced methane uptake
Tian, T., Zeng, Z., Vulpe, D., Casco, M. E., Divitini, G., Midgley, P. A., Silvestre-Albero, J., Tan, J.-C., Moghadam, P. Z., & Fairen-Jimenez, D. (2018) · Nature Materials · doi:10.1038/nmat5050 · Cited by 549
Multifunctional metal–organic frameworks constructed from meta-benzenedicarboxylate units
He, Y., Li, B., O'Keeffe, M., & Chen, B. (2014) · Chem. Soc. Rev. · doi:10.1039/c4cs00041b · Cited by 506
Metal–organic framework gels and monoliths
Hou, J., Sapnik, A. F., & Bennett, T. D. (2020) · Chemical Science · doi:10.1039/c9sc04961d · Cited by 331
Saha, D., Grappe, H. A., Chakraborty, A., & Orkoulas, G. (2016) · Chemical Reviews · doi:10.1021/acs.chemrev.5b00745 · Cited by 316
A porous metal-organic framework with ultrahigh acetylene uptake capacity under ambient conditions
Pang, J., Jiang, F., Wu, M., Liu, C., Su, K., Lu, W., Yuan, D., & Hong, M. (2015) · Nature Communications · doi:10.1038/ncomms8575 · Cited by 316
Energy-based descriptors to rapidly predict hydrogen storage in metal–organic frameworks
Bucior, B. J., Bobbitt, N. S., Islamoglu, T., Goswami, S., Gopalan, A., Yildirim, T., Farha, O. K., Bagheri, N., & Snurr, R. Q. (2019) · Molecular Systems Design & Engineering · doi:10.1039/c8me00050f · Cited by 308
Self-citationElectronic Chemical Potentials of Porous Metal–Organic Frameworks
Butler, K. T., Hendon, C. H., & Walsh, A. (2014) · Journal of the American Chemical Society · doi:10.1021/ja4110073 · Cited by 293
Present and future of MOF research in the field of adsorption and molecular separation
Petit, C. (2018) · Current Opinion in Chemical Engineering · doi:10.1016/j.coche.2018.04.004 · Cited by 292
Selective Adsorption of Sulfur Dioxide in a Robust Metal–Organic Framework Material
Savage, M., Cheng, Y., Easun, T. L., Eyley, J. E., Argent, S. P., Warren, M. R., Lewis, W., Murray, C., Tang, C. C., Frogley, M. D., et al. (2016) · Advanced Materials · doi:10.1002/adma.201602338 · Cited by 267
Porous metal–organic frameworks for fuel storage
He, Y., Chen, F., Li, B., Qian, G., Zhou, W., & Chen, B. (2018) · Coordination Chemistry Reviews · doi:10.1016/j.ccr.2017.10.002 · Cited by 267
Zeolite-templated carbons – three-dimensional microporous graphene frameworks
Nishihara, H., & Kyotani, T. (2018) · Chemical Communications · doi:10.1039/c8cc01932k · Cited by 266
Kim, H. K., Yun, W. S., Kim, M.-B., Kim, J. Y., Bae, Y.-S., Lee, J., & Jeong, N. C. (2015) · Journal of the American Chemical Society · doi:10.1021/jacs.5b06637 · Cited by 265
Capturing chemical intuition in synthesis of metal-organic frameworks
Moosavi, S. M., Chidambaram, A., Talirz, L., Haranczyk, M., Stylianou, K. C., & Smit, B. (2019) · Nature Communications · doi:10.1038/s41467-019-08483-9 · Cited by 257
Jablonka, K. M., Ai, Q., Al-Feghali, A., Badhwar, S., Bocarsly, J. D., Bran, A. M., Bringuier, S., Brinson, L. C., Choudhary, K., Circi, D., et al. (2023) · Digital Discovery · doi:10.1039/d3dd00113j · Cited by 218
Balahmar, N., Mitchell, A. C., & Mokaya, R. (2015) · Advanced Energy Materials · doi:10.1002/aenm.201500867 · Cited by 177
Densified HKUST-1 Monoliths as a Route to High Volumetric and Gravimetric Hydrogen Storage Capacity
Madden, D. G., O’Nolan, D., Rampal, N., Babu, R., Çamur, C., Al Shakhs, A. N., Zhang, S.-Y., Rance, G. A., Perez, J., Maria Casati, N. P., et al. (2022) · Journal of the American Chemical Society · doi:10.1021/jacs.2c04608 · Cited by 123
Pérez-Botella, E., Palomino, M., Valencia, S., & Rey, F. (2019) · Green Energy and Technology · doi:10.1007/978-981-13-3504-4_7 · Cited by 29
Metadata
- Authors
- Peng, Y., Krungleviciute, V., Eryazici, I., Hupp, J. T., Farha, O. K., & Yildirim, T.
- Venue
- Journal of the American Chemical Society
- Publisher
- American Chemical Society (ACS)
- Published
- 2013-07-26
- Volume
- 135
- Issue
- 32
- Pages
- 11887-11894
- ISSN
- 0002-7863 (ISSN-L)
- 1520-5126
- OpenAlex
- W2027788760
- Cited by
- 1,018
- References
- 52
- FWCI
- 40.07
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.
