The DOI matches its Crossref record; 15 of the 15 references it cites were found in a registry or an index.
Aluminum Incorporation in Calcium Silicate Hydrates (C−S−H) Depending on Their Ca/Si Ratio
Abstract
27 Al magic angle spinning nuclear magnetic resonance ( 27 Al MAS NMR) spectroscopy at different magnetic fields was used to characterize the aluminum incorporation in the tetrahedral−octahedral−tetrahedral (Te−Oc−Te) structure of calcium silicate hydrates (C−S−H), which are the main constituents of the hydrated cement-based materials. C−S−H of different calcium/silicon ratio (0.66 < Ca/Si < 1.7) were synthesized in the presence of aluminum. Two different aluminum/silicon ratios (0.1 and 0.3) were tested. The maximum Al(IV)/[(Al(IV) + Si] ratio in the C−S−H that could be detected in these series of experiments was 0.17. Results show in this case that, when the tetrahedral sheet is formed by linear silicate chains, Al 3+ preferentially substitutes a nonbridging Si 4+ . The rupture of the chains, caused by an increase of the Ca/Si ratio, makes such a position unstable and a redistribution of the aluminum in the tetrahedral sites occurs. Results also indicate that the substitution of Si 4+ cannot take place when the tetrahedral sheet is composed of dimers (i.e., for high Ca/Si ratios). In these cases, Al 3+ substitutes Ca 2+ in the interlayer space (5-fold coordinated) and in the octahedral sheet (6-fold coordinated). However, this kind of substitution remains limited. The amount of aluminum incorporated in the C−S−H structure increases with the length of chains. Results confirm that C 2 AH 8 is not a time-stable phase.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
High-resolution solid-state NMR of silicates and zeolites
Boddenberg, B. (1988) · Applied Catalysis · doi:10.1016/s0166-9834(00)80098-6 · Cited by 1,819
Proposed Structure for Calcium Silicate Hydrate Gel
TAYLOR, H. F. W. (1986) · Journal of the American Ceramic Society · doi:10.1111/j.1151-2916.1986.tb07446.x · Cited by 679
High-resolution aluminum-27 NMR of aluminosilicates
Lippmaa, E., Samoson, A., & Magi, M. (1986) · Journal of the American Chemical Society · doi:10.1021/ja00268a002 · Cited by 624
Solid-state high-resolution silicon-29 chemical shifts in silicates
Magi, M., Lippmaa, E., Samoson, A., Engelhardt, G., & Grimmer, A. R. (1984) · The Journal of Physical Chemistry · doi:10.1021/j150652a015 · Cited by 554
Richardson, I. G., Brough, A. R., Brydson, R., Groves, G. W., & Dobson, C. M. (1993) · Journal of the American Ceramic Society · doi:10.1111/j.1151-2916.1993.tb07765.x · Cited by 327
Nuclear Magnetic Resonance Spectroscopy of Cement-Based Materials
(1998) · Springer eBooks · doi:10.1007/978-3-642-80432-8 · Cited by 250
Silicon‐29 Magic Angle Spinning Nuclear Magnetic Resonance Study of Calcium Silicate Hydrates
Grutzeck, M., Benesi, A., & Fanning, B. (1989) · Journal of the American Ceramic Society · doi:10.1111/j.1151-2916.1989.tb06192.x · Cited by 196
29Si and 17O NMR investigation of the structure of some crystalline calcium silicate hydrates
Cong, X., & Kirkpatrick, R. J. (1996) · Advanced Cement Based Materials · doi:10.1016/s1065-7355(96)90045-0 · Cited by 165
Faucon, P., Charpentier, T., Bertrandie, D., Nonat, A., Virlet, J., & Petit, J.-C. (1998) · Inorganic Chemistry · doi:10.1021/ic9800076 · Cited by 124
Self-citationFlint, E. P., & Wells, L. S. (1934) · Bureau of Standards Journal of Research · doi:10.6028/jres.012.060 · Cited by 109
Cited by
Nanotechnology in concrete – A review
Sanchez, F., & Sobolev, K. (2010) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2010.03.014 · Cited by 1,834
Yip, C. K., Lukey, G. C., & van Deventer, J. S. J. (2005) · Cement and Concrete Research · doi:10.1016/j.cemconres.2004.10.042 · Cited by 1,274
Constantinides, G., & Ulm, F.-J. (2004) · Cement and Concrete Research · doi:10.1016/s0008-8846(03)00230-8 · Cited by 1,226
Bernal, S. A., Provis, J. L., Walkley, B., San Nicolas, R., Gehman, J. D., Brice, D. G., Kilcullen, A. R., Duxson, P., & van Deventer, J. S. J. (2013) · Cement and Concrete Research · doi:10.1016/j.cemconres.2013.06.007 · Cited by 1,019
Myers, R. J., Bernal, S. A., San Nicolas, R., & Provis, J. L. (2013) · Langmuir · doi:10.1021/la4000473 · Cited by 579
Incorporation of aluminium in calcium-silicate-hydrates
L’Hôpital, E., Lothenbach, B., Le Saout, G., Kulik, D., & Scrivener, K. (2015) · Cement and Concrete Research · doi:10.1016/j.cemconres.2015.04.007 · Cited by 551
Walkley, B., San Nicolas, R., Sani, M.-A., Rees, G. J., Hanna, J. V., van Deventer, J. S. J., & Provis, J. L. (2016) · Cement and Concrete Research · doi:10.1016/j.cemconres.2016.08.010 · Cited by 544
Calcium silicate hydrates: Solid and liquid phase composition
Lothenbach, B., & Nonat, A. (2015) · Cement and Concrete Research · doi:10.1016/j.cemconres.2015.03.019 · Cited by 538
The role of Al in C–S–H: NMR, XRD, and compositional results for precipitated samples
Sun, G. K., Young, J. F., & Kirkpatrick, R. J. (2006) · Cement and Concrete Research · doi:10.1016/j.cemconres.2005.03.002 · Cited by 454
Model structures for C-(A)-S-H(I)
Richardson, I. G. (2014) · Acta Crystallographica Section B Structural Science, Crystal Engineering and Materials · doi:10.1107/s2052520614021982 · Cited by 450
Andersen, M. D., Jakobsen, H. J., & Skibsted, J. (2003) · Inorganic Chemistry · doi:10.1021/ic020607b · Cited by 434
Andersen, M. D., Jakobsen, H. J., & Skibsted, J. (2004) · Cement and Concrete Research · doi:10.1016/j.cemconres.2003.10.009 · Cited by 423
Andersen, M. D., Jakobsen, H. J., & Skibsted, J. (2006) · Cement and Concrete Research · doi:10.1016/j.cemconres.2005.04.010 · Cited by 405
Variation in hybrid cements over time. Alkaline activation of fly ash–portland cement blends
García-Lodeiro, I., Fernández-Jiménez, A., & Palomo, A. (2013) · Cement and Concrete Research · doi:10.1016/j.cemconres.2013.03.022 · Cited by 385
Taylor, R., Richardson, I. G., & Brydson, R. M. D. (2010) · Cement and Concrete Research · doi:10.1016/j.cemconres.2010.02.012 · Cited by 377
Solid-state nuclear magnetic resonance spectroscopy of cements
Walkley, B., & Provis, J. L. (2019) · Materials Today Advances · doi:10.1016/j.mtadv.2019.100007 · Cited by 361
Hydration of alkali-activated slag: comparison with ordinary Portland cement
Gruskovnjak, A., Lothenbach, B., Holzer, L., Figi, R., & Winnefeld, F. (2006) · Advances in Cement Research · doi:10.1680/adcr.2006.18.3.119 · Cited by 349
Influence of calcium to silica ratio on aluminium uptake in calcium silicate hydrate
L’Hôpital, E., Lothenbach, B., Kulik, D. A., & Scrivener, K. (2016) · Cement and Concrete Research · doi:10.1016/j.cemconres.2016.01.014 · Cited by 349
27 Al and 29 Si Solid-State NMR Characterization of Calcium-Aluminosilicate-Hydrate
Pardal, X., Brunet, F., Charpentier, T., Pochard, I., & Nonat, A. (2012) · Inorganic Chemistry · doi:10.1021/ic202124x · Cited by 328
A thermodynamic model for C-(N-)A-S-H gel: CNASH_ss. Derivation and validation
Myers, R. J., Bernal, S. A., & Provis, J. L. (2014) · Cement and Concrete Research · doi:10.1016/j.cemconres.2014.07.005 · Cited by 312
Auroy, M., Poyet, S., Le Bescop, P., Torrenti, J.-M., Charpentier, T., Moskura, M., & Bourbon, X. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.04.012 · Cited by 303
Engineering the bonding scheme in C–S–H: The iono-covalent framework
Pellenq, R. J.-M., Lequeux, N., & van Damme, H. (2008) · Cement and Concrete Research · doi:10.1016/j.cemconres.2007.09.026 · Cited by 303
The Role of Al in Cross‐Linking of Alkali‐Activated Slag Cements
Myers, R. J., Bernal, S. A., Gehman, J. D., van Deventer, J. S. J., & Provis, J. L. (2015) · Journal of the American Ceramic Society · doi:10.1111/jace.13360 · Cited by 287
Microstructural and bulk property changes in hardened cement paste during the first drying process
Maruyama, I., Nishioka, Y., Igarashi, G., & Matsui, K. (2014) · Cement and Concrete Research · doi:10.1016/j.cemconres.2014.01.007 · Cited by 284
Composition of C–S–H in pastes with increasing levels of silica fume addition
Rossen, J. E., Lothenbach, B., & Scrivener, K. L. (2015) · Cement and Concrete Research · doi:10.1016/j.cemconres.2015.04.016 · Cited by 282
Gao, X., Yu, Q. L., & Brouwers, H. J. H. (2017) · Ceramics International · doi:10.1016/j.ceramint.2017.06.108 · Cited by 261
Thermodynamic equilibrium calculations in cementitious systems
Lothenbach, B. (2010) · Materials and Structures · doi:10.1617/s11527-010-9592-x · Cited by 258
Structural evolution of an alkali sulfate activated slag cement
Mobasher, N., Bernal, S. A., & Provis, J. L. (2016) · Journal of Nuclear Materials · doi:10.1016/j.jnucmat.2015.11.016 · Cited by 186
Sevelsted, T. F., Herfort, D., & Skibsted, J. (2013) · Cement and Concrete Research · doi:10.1016/j.cemconres.2013.05.010 · Cited by 84
Slag-Based Cements That Resist Damage Induced by Carbon Dioxide
Ke, X., Criado, M., Provis, J. L., & Bernal, S. A. (2018) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.7b04730 · Cited by 62
Metadata
- Authors
- Faucon, P., Delagrave, A., J. C. Petit, Richet, C., Marchand, J. M., & Zanni, H.
- Venue
- The Journal of Physical Chemistry B
- Publisher
- American Chemical Society (ACS)
- Published
- 1999-08-31
- Volume
- 103
- Issue
- 37
- Pages
- 7796-7802
- ISSN
- 1520-5207 (ISSN-L)
- 1520-6106
- OpenAlex
- W1997734218
- Cited by
- 258
- References
- 15
- FWCI
- 4.12
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.