The DOI matches its Crossref record; 24 of the 24 references it cites were found in a registry or an index.
Environmental Life Cycle Analysis of Distributed Three-Dimensional Printing and Conventional Manufacturing of Polymer Products
Abstract
With the recent development of the RepRap, an open-source self-replicating rapid prototyper, low-cost three-dimensional (3D) printing is now a technically viable form of distributed manufacturing of polymer-based products. However, the aggregate environmental benefits of distributed manufacturing are not clear due to scale reductions and the potential for increases in embodied energy. To quantify the environmental impact of distributed manufacturing using 3D printers, a life cycle analysis was performed on three plastic products. The embodied energy and emissions from conventional large-scale production in low-labor cost countries and shipping are compared to experimental measurements on a RepRap with and without solar photovoltaic (PV) power fabricating products with acrylonitrile butadiene styrene (ABS) and polylactic acid (PLA). The results indicate that the cumulative energy demand of manufacturing polymer products can be reduced by 41–64% (55–74% with PV) and concomitant emission reductions using distributed manufacturing with existing low-cost open-source 3D printers when using <25% fill PLA. Less pronounced positive environmental results are observed with ABS, which demands higher temperatures for the print bed and extruder. Overall, the results indicate that distributed manufacturing using open-source 3D printers has the potential to have a lower environmental impact than conventional manufacturing for a variety of products.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
The pollution of the marine environment by plastic debris: a review.
Derraik, J. G. B. (2002) · Marine Pollution Bulletin · doi:10.1016/s0025-326x(02)00220-5 · Cited by 4,042
Life Cycle Assessment: Past, Present, and Future
Guinée, J. B., Heijungs, R., Huppes, G., Zamagni, A., Masoni, P., Buonamici, R., Ekvall, T., & Rydberg, T. (2011) · Environmental Science & Technology · doi:10.1021/es101316v · Cited by 1,692
FAB: The Coming Revolution on Your Desktop--from Personal Computers to Personal Fabrication
Gershenfeld, N. (2005) · Works - Scholarship, Research, & Creative Expression (Swarthmore College) · Cited by 862
RepRap – the replicating rapid prototyper
Jones, R., Haufe, P., Sells, E., Iravani, P., Olliver, V., Palmer, C., & Bowyer, A. (2011) · Robotica · doi:10.1017/s026357471000069x · Cited by 736
Additive layered manufacturing: sectors of industrial application shown through case studies
Petrovic, V., Vicente Haro Gonzalez, J., Jordá Ferrando, O., Delgado Gordillo, J., Ramón Blasco Puchades, J., & Portolés Griñan, L. (2011) · International Journal of Production Research · doi:10.1080/00207540903479786 · Cited by 676
Emissions from Photovoltaic Life Cycles
Fthenakis, V. M., Kim, H. C., & Alsema, E. (2008) · Environmental Science & Technology · doi:10.1021/es071763q · Cited by 608
Building Research Equipment with Free, Open-Source Hardware
Pearce, J. M. (2012) · Science · doi:10.1126/science.1228183 · Cited by 561
Self-citationSustainability Metrics: Life Cycle Assessment and Green Design in Polymers
Tabone, M. D., Cregg, J. J., Beckman, E. J., & Landis, A. E. (2010) · Environmental Science & Technology · doi:10.1021/es101640n · Cited by 416
Life-cycle economic analysis of distributed manufacturing with open-source 3-D printers
Wittbrodt, B. T., Glover, A. G., Laureto, J., Anzalone, G. C., Oppliger, D., Irwin, J. L., & Pearce, J. M. (2013) · Mechatronics · doi:10.1016/j.mechatronics.2013.06.002 · Cited by 416
Self-citationKreiger, M. A., Mulder, M. L., Glover, A. G., & Pearce, J. M. (2014) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2014.02.009 · Cited by 350
Self-citationPhotovoltaics — a path to sustainable futures
Pearce, J. M. (2002) · Futures · doi:10.1016/s0016-3287(02)00008-3 · Cited by 291
Self-citationDistributed recycling of waste polymer into RepRap feedstock
Baechler, C., DeVuono, M., & Pearce, J. M. (2013) · Rapid Prototyping Journal · doi:10.1108/13552541311302978 · Cited by 269
Self-citationSells, E., Bailard, S., Smith, Z., et al. (2009) · WORLD SCIENTIFIC eBooks · doi:10.1142/9789814280280_0028 · Cited by 210
Identifying Improvement Potentials in Cement Production with Life Cycle Assessment
Boesch, M. E., & Hellweg, S. (2010) · Environmental Science & Technology · doi:10.1021/es100771k · Cited by 198
Open-Source 3D-Printable Optics Equipment
Zhang, C., Anzalone, N. C., Faria, R. P., et al. (2013) · PLoS ONE · doi:10.1371/journal.pone.0059840 · Cited by 197
Life Cycle Assessment and Grid Electricity: What Do We Know and What Can We Know?
Weber, C. L., Jaramillo, P., Marriott, J., & Samaras, C. (2010) · Environmental Science & Technology · doi:10.1021/es9017909 · Cited by 174
The fate of carbon compounds in the landfill disposal of organic matter
Rees, J. F. (1980) · Journal of Chemical Technology and Biotechnology · doi:10.1002/jctb.503300121 · Cited by 171
Air Emissions Due To Wind And Solar Power
Katzenstein, W., & Apt, J. (2008) · Environmental Science & Technology · doi:10.1021/es801437t · Cited by 160
The Intellectual Property Implications of Low-Cost 3D Printing
Bradshaw, S., Bowyer, A., & Haufe, P. (2010) · SCRIPTed A Journal of Law Technology & Society · doi:10.2966/scrip.070110.5 · Cited by 144
Zhai, P., & Williams, E. (2010) · Environmental Science & Technology · doi:10.1021/es1026695 · Cited by 122
Kreiger, M. A., & Pearce, J. M. (2013) · MRS Proceedings · doi:10.1557/opl.2013.319 · Cited by 114
Self-citationDistributed Recycling of Post-Consumer Plastic Waste in Rural Areas
Kreiger, M. A., Anzalone, G. C., Mulder, M., Glover, A. G., & Pearce, J. M. (2013) · MRS Proceedings · doi:10.1557/opl.2013.258 · Cited by 94
Self-citationIndustrial symbiosis of very large-scale photovoltaic manufacturing
Pearce, J. M. (2007) · Renewable Energy · doi:10.1016/j.renene.2007.07.002 · Cited by 83
Self-citationA Comparative Life Cycle Assessment of Petroleum and Soybean-Based Lubricants
Miller, S. A., Landis, A. E., Theis, T. L., & Reich, R. A. (2007) · Environmental Science & Technology · doi:10.1021/es062727e · Cited by 59
Cited by
A global sustainability perspective on 3D printing technologies
Gebler, M., Schoot Uiterkamp, A. J. M., & Visser, C. (2014) · Energy Policy · doi:10.1016/j.enpol.2014.08.033 · Cited by 950
3D printing in aerospace and its long-term sustainability
Joshi, S. C., & Sheikh, A. A. (2015) · Virtual and Physical Prototyping · doi:10.1080/17452759.2015.1111519 · Cited by 628
Sustainability of additive manufacturing: An overview on its energy demand and environmental impact
Peng, T., Kellens, K., Tang, R., Chen, C., & Chen, G. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2018.04.022 · Cited by 426
The Potential of Additive Manufacturing in the Smart Factory Industrial 4.0: A Review
Mehrpouya, M., Dehghanghadikolaei, A., Fotovvati, B., Vosooghnia, A., Emamian, S. S., & Gisario, A. (2019) · Applied Sciences · doi:10.3390/app9183865 · Cited by 419
Kassab, A., Al Nabhani, D., Mohanty, P., Pannier, C., & Ayoub, G. Y. (2023) · Polymers · doi:10.3390/polym15193881 · Cited by 141
Metadata
- Authors
- Kreiger, M., & Pearce, J. M.
- Venue
- ACS Sustainable Chemistry & Engineering
- Publisher
- American Chemical Society (ACS)
- Published
- 2013-10-02
- Volume
- 1
- Issue
- 12
- Pages
- 1511-1519
- ISSN
- 2168-0485 (ISSN-L)
- OpenAlex
- W2049089255
- Cited by
- 295
- References
- 24
- FWCI
- 25.93
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.