The DOI matches its Crossref record; 45 of the 45 references it cites were found in a registry or an index.
Frictional and hydrologic properties of clay‐rich fault gouge
Open accessAbstract
The slip behavior of major faults depends largely on the frictional and hydrologic properties of fault gouge. We report on laboratory experiments designed to measure the strength, friction constitutive properties, and permeability of a suite of saturated clay‐rich fault gouges, including: a 50:50% mixture of montmorillonite‐quartz, powdered illite shale, and powdered chlorite schist. Friction measurements indicate that clay‐rich gouges are consistently weak, with steady state coefficient of sliding friction of <0.35. The montmorillonite gouge (μ = 0.19–0.23) is consistently weaker than the illite and chlorite gouges (μ = 0.27–0.32). At effective normal stresses from 12 to 59 MPa, all gouges show velocity‐strengthening frictional behavior in the sliding velocity range 0.5–300 μ m/s. We suggest that the velocity‐strengthening behavior we observe is related to saturation of real contact area, as documented by the friction parameter b, and is an inherent characteristic of noncohesive, unlithified clay‐rich gouge. Permeability normal to the gouge layer measured before, during, and after shear ranges from 8.3 × 10−21 m 2 to 3.6 × 10−16 m 2; permeability decreases dramatically with shearing, and to a lesser extent with increasing effective normal stress. The chlorite gouge is consistently more permeable than the montmorillonite and illite gouge and maintains a higher permeability after shearing. Permeability reduction via shear is pronounced at shear strains ≲5 and is smaller at higher strain, suggesting that shear‐induced permeability reduction is linked to fabric development early in the deformation history. Our results imply that the potential for development of excess pore pressure in low‐permeability fault gouge depends on both clay mineralogy and shear strain.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Byerlee, J. (1978) · pure and applied geophysics · doi:10.1007/bf00876528 · Cited by 4,029
The mechanics of earthquakes and faulting
(1990) · Choice Reviews Online · doi:10.5860/choice.28-1579 · Cited by 3,569
Modeling of rock friction: 1. Experimental results and constitutive equations
Dieterich, J. H. (1979) · Journal of Geophysical Research: Solid Earth · doi:10.1029/jb084ib05p02161 · Cited by 3,049
The Mechanics of Earthquakes and Faulting
Scholz, C. H. (2002) · Cambridge University Press eBooks · doi:10.1017/cbo9780511818516 · Cited by 2,515
Mechanics of fold‐and‐thrust belts and accretionary wedges
Davis, D., Suppe, J., & Dahlen, F. A. (1983) · Journal of Geophysical Research: Solid Earth · doi:10.1029/jb088ib02p01153 · Cited by 2,304
Scholz, C. H. (1998) · Nature · doi:10.1038/34097 · Cited by 2,227
ROLE OF FLUID PRESSURE IN MECHANICS OF OVERTHRUST FAULTING
KING HUBBERT, M., & RUBEY, W. W. (1959) · Geological Society of America Bulletin · doi:10.1130/0016-7606(1959)70[115:rofpim]2.0.co;2 · Cited by 2,081
Heating and weakening of faults during earthquake slip
Rice, J. R. (2006) · Journal of Geophysical Research: Solid Earth · doi:10.1029/2005jb004006 · Cited by 1,322
On the mechanics of earthquake afterslip
Marone, C. J., Scholtz, C. H., & Bilham, R. (1991) · Journal of Geophysical Research: Solid Earth · doi:10.1029/91jb00275 · Cited by 677
Self-citationRice, J. R. (1992) · International Geophysics · doi:10.1016/s0074-6142(08)62835-1 · Cited by 659
The seismogenic zone of subduction thrust faults
Hyndman, R. D., Yamano, M., & Oleskevich, D. A. (1997) · Island Arc · doi:10.1111/j.1440-1738.1997.tb00175.x · Cited by 636
Frictional behavior and constitutive modeling of simulated fault gouge
Marone, C., Raleigh, C. B., & Scholz, C. H. (1990) · Journal of Geophysical Research: Solid Earth · doi:10.1029/jb095ib05p07007 · Cited by 630
Self-citationFault stress states, pore pressure distributions, and the weakness of the San Andreas Fault
RICE, J. R. (1992) · Medical Entomology and Zoology · Cited by 587
Saffer, D. M., & Marone, C. (2003) · Earth and Planetary Science Letters · doi:10.1016/s0012-821x(03)00424-2 · Cited by 586
Self-citationConstitutive Properties of Faults With Simulated Gouge
Dieterich, J. H. (2013) · Geophysical Monograph Series · doi:10.1029/gm024p0103 · Cited by 488
Perfettini, H., & Avouac, J. ‐. (2004) · Journal of Geophysical Research: Solid Earth · doi:10.1029/2003jb002488 · Cited by 488
Moore, J. C., & Saffer, D. (2001) · Geology · doi:10.1130/0091-7613(2001)029<0183:ulotsz>2.0.co;2 · Cited by 481
Self-citationThe depth of seismic faulting and the upper transition from stable to unstable slip regimes
Marone, C., & Scholz, C. H. (1988) · Geophysical Research Letters · doi:10.1029/gl015i006p00621 · Cited by 458
Self-citationAccretionary prisms in subduction earthquake cycles: The theory of dynamic Coulomb wedge
Wang, K., & Hu, Y. (2006) · Journal of Geophysical Research: Solid Earth · doi:10.1029/2005jb004094 · Cited by 436
Creep, compaction and the weak rheology of major faults
Sleep, N. H., & Blanpied, M. L. (1992) · Nature · doi:10.1038/359687a0 · Cited by 431
Friction, overpressure and fault normal compression
Byerlee, J. (1990) · Geophysical Research Letters · doi:10.1029/gl017i012p02109 · Cited by 396
The effect of mineral bond strength and adsorbed water on fault gouge frictional strength
Morrow, C. A., Moore, D. E., & Lockner, D. A. (2000) · Geophysical Research Letters · doi:10.1029/1999gl008401 · Cited by 386
Moore, D. E., & Lockner, D. A. (2004) · Journal of Geophysical Research: Solid Earth · doi:10.1029/2003jb002582 · Cited by 330
Permeability and petrophysical properties of 30 natural mudstones
Yang, Y., & Aplin, A. C. (2007) · Journal of Geophysical Research: Solid Earth · doi:10.1029/2005jb004243 · Cited by 303
Crawford, B. R., Faulkner, D. R., & Rutter, E. H. (2008) · Journal of Geophysical Research: Solid Earth · doi:10.1029/2006jb004634 · Cited by 271
Permeability of fault gouge under confining pressure and shear stress
Morrow, C. A., Shi, L. Q., & Byerlee, J. D. (1984) · Journal of Geophysical Research: Solid Earth · doi:10.1029/jb089ib05p03193 · Cited by 266
Logan, J. M., & Rauenzahn, K. A. (1987) · Tectonophysics · doi:10.1016/0040-1951(87)90010-2 · Cited by 263
Multimechanism friction constitutive model for ultrafine quartz gouge at hypocentral conditions
Chester, F. M., & Higgs, N. G. (1992) · Journal of Geophysical Research: Solid Earth · doi:10.1029/91jb02349 · Cited by 254
Permeability of illite‐bearing shale: 1. Anisotropy and effects of clay content and loading
Kwon, O., Kronenberg, A. K., Gangi, A. F., Johnson, B., & Herbert, B. E. (2004) · Journal of Geophysical Research: Solid Earth · doi:10.1029/2004jb003052 · Cited by 253
Water from low‐permeability sediments and land subsidence
Domenico, P. A., & Mifflin, M. D. (1965) · Water Resources Research · doi:10.1029/wr001i004p00563 · Cited by 249
Experimental deformation of muscovite
Mares, V. M., & Kronenberg, A. K. (1993) · Journal of Structural Geology · doi:10.1016/0191-8141(93)90156-5 · Cited by 220
Chapter 3 Frictional Strength and the Effective Pressure Law of Montmorillonite and lllite Clays
Morrow, C., Radney, B., & Byerlee, J. (1992) · International Geophysics · doi:10.1016/s0074-6142(08)62815-6 · Cited by 186
Talc friction in the temperature range 25°–400 °C: Relevance for Fault-Zone Weakening
Moore, D. E., & Lockner, D. A. (2008) · Tectonophysics · doi:10.1016/j.tecto.2007.11.039 · Cited by 177
Bizzarri, A., & Cocco, M. (2006) · Journal of Geophysical Research: Solid Earth · doi:10.1029/2005jb003862 · Cited by 170
Stress in the Lithosphere and the Strength of Active Faults
HICKMAN, S. H. (1991) · Reviews of Geophysics · doi:10.1002/rog.1991.29.s2.759 · Cited by 164
Mechanics of low‐stress forearcs: Nankai and Cascadia
Wang, K., & He, J. (1999) · Journal of Geophysical Research Atmospheres · doi:10.1029/1999jb900103 · Cited by 155
Effects of simulated clay gouges on the sliding behavior of Tennessee sandston
Shimamoto, T., & Logan, J. M. (1981) · Tectonophysics · doi:10.1016/0040-1951(81)90276-6 · Cited by 152
Kopf, A., & Brown, K. M. (2003) · Marine Geology · doi:10.1016/s0025-3227(03)00286-x · Cited by 126
Accretion and Erosion in Subduction Zones: The Role of Fluids
Pichon, X. L., Henry, P., & Lallemant, S. (1993) · Annual Review of Earth and Planetary Sciences · doi:10.1146/annurev.ea.21.050193.001515 · Cited by 110
Saffer, D. M., & Bekins, B. (2006) · Journal of Geophysical Research Atmospheres · doi:10.1029/2005jb003990 · Cited by 110
Self-citationClay gouges in the San Andreas Fault System and their possible implications
Wu, F. T., Blatter, L., & Roberson, H. E. (1975) · Pure and Applied Geophysics · doi:10.1007/bf01592901 · Cited by 97
Wiersberg, T., & Erzinger, J. (2008) · Applied Geochemistry · doi:10.1016/j.apgeochem.2008.01.012 · Cited by 87
10. How Accretionary Prisms Elucidate Seismogenesis in Subduction Zones
Moore, J. C., Rowe, C. D., & Meneghini, F. (2007) · Columbia University Press eBooks · doi:10.7312/dixo13866-010 · Cited by 76
Cited by
Faulkner, D. R., Jackson, C. A. L., Lunn, R. J., Schlische, R. W., Shipton, Z. K., Wibberley, C. A. J., & Withjack, M. O. (2010) · Journal of Structural Geology · doi:10.1016/j.jsg.2010.06.009 · Cited by 1,513
Hydrogeology and Mechanics of Subduction Zone Forearcs: Fluid Flow and Pore Pressure
Saffer, D. M., & Tobin, H. J. (2011) · Annual Review of Earth and Planetary Sciences · doi:10.1146/annurev-earth-040610-133408 · Cited by 554
Self-citationSubsurface carbon dioxide and hydrogen storage for a sustainable energy future
Krevor, S., de Coninck, H., Gasda, S. E., Ghaleigh, N. S., de Gooyert, V., Hajibeygi, H., Juanes, R., Neufeld, J., Roberts, J. J., & Swennenhuis, F. (2023) · Nature Reviews Earth & Environment · doi:10.1038/s43017-022-00376-8 · Cited by 481
From Geodetic Imaging of Seismic and Aseismic Fault Slip to Dynamic Modeling of the Seismic Cycle
Avouac, J.-P. (2015) · Annual Review of Earth and Planetary Sciences · doi:10.1146/annurev-earth-060614-105302 · Cited by 419
On the relation between fault strength and frictional stability
Ikari, M. J., Marone, C., & Saffer, D. M. (2011) · Geology · doi:10.1130/g31416.1 · Cited by 379
Self-citation
Metadata
- Authors
- Ikari, M. J., Saffer, D. M., & Marone, C.
- Venue
- Journal of Geophysical Research: Solid Earth
- Publisher
- American Geophysical Union (AGU)
- Published
- 2009-05
- Volume
- 114
- Issue
- B5
- ISSN
- 0148-0227 (ISSN-L)
- OpenAlex
- W2026254189
- Cited by
- 474
- References
- 45
- FWCI
- 16.04
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.