Student or educator? Sign up with your school email and get 6 months of Pro free.
CoChat

The DOI matches its Crossref record; 48 of the 48 references it cites were found in a registry or an index; 2 of the 6 sources its claims cite were checked for support.

Nanobatteries in redox-based resistive switches require extension of memristor theory

Open access
Valov, I., Linn, E., Tappertzhofen, S., Schmelzer, S., van den Hurk, J., Lentz, F., Waser, R. · 2013 · Nature Communications

Abstract

Redox-based nanoionic resistive memory cells are one of the most promising emerging nanodevices for future information technology with applications for memory, logic and neuromorphic computing. Recently, the serendipitous discovery of the link between redox-based nanoionic-resistive memory cells and memristors and memristive devices has further intensified the research in this field. Here we show on both a theoretical and an experimental level that nanoionic-type memristive elements are inherently controlled by non-equilibrium states resulting in a nanobattery. As a result, the memristor theory must be extended to fit the observed non-zero-crossing I–V characteristics. The initial electromotive force of the nanobattery depends on the chemistry and the transport properties of the materials system but can also be introduced during redox-based nanoionic-resistive memory cell operations. The emf has a strong impact on the dynamic behaviour of nanoscale memories, and thus, its control is one of the key factors for future device development and accurate modelling. The original definition of a memristor envisions a two-terminal memory device with a pinched, zero-crossing hysteresis loop. As the authors show here, an electromotive force leads to non-zero-crossing characteristics in nanoionic-type memristors, implying that the memristor definition must be amended.

Overview

CoChat Summary

## TL;DR

The paper argues that redox-based resistive switching memories (ReRAM) are not pure passive memristors because they generate an internal electromotive force (emf) from non-equilibrium chemical potential gradients. The authors show experimentally and theoretically that this “nanobattery” can reach up to a few hundred millivolts and requires extending memristor theory to account for non-zero-crossing I–V behavior.

## Key findings

  • Across the ReRAM cells tested, the authors report significant (electro)chemical potential gradients generated during operation, producing an emf and making the devices behave as nanoscale batteries.
  • In Ag/SiO2/Pt cells, the short-circuit discharge after RESET released a total charge of about 5 nC, which the authors say corresponds to about 2 monolayers of Ag; the dielectric discharge of the cell capacitor was about 0.4 pC.
  • For Ag/Ag–GeS2.2/Pt and Ag/Ag–GeSe2.3/Pt systems, the authors say they demonstrated a Nernst emf and observed an emf of about −450 mV in a voltage-modified state.
  • The paper states that ReRAM cells show non-zero-crossing I–V behavior, so the original memristor theory must be extended; the authors model this with an added emf source and nonlinear internal resistance.

## Methods

  • The study combined theoretical modeling with electrical measurements on ECM and VCM ReRAM cells.
  • Sample set included Ag/SiO2/Pt, Ag/Ag–GeS2.2/Pt, Ag/Ag–GeSe2.3/Pt, plus selected WOx, SrTiO3, and Ta2O5 cells prepared on platinised silicon wafers.
  • Measurements were done in a four-needle microprobe station; I–V sweeps used triangular voltages from −1.5 to 1.5 V at sweep rates of 30 mV s−1 to 2 V s−1, and emf was measured with high-impedance instruments for comparison.

## Limitations

  • The paper states that the contribution of the Gibbs–Thomson potential could not be clearly distinguished from the diffusion potential in the systems they studied.
  • The text makes evident that some measurements are system-specific and rely on particular material stacks and cell states; the authors do not claim the same quantitative emf values for every ReRAM structure (evident from the text).
  • The paper notes that detailed measurement resolution/accuracy and additional modeling details are in the Supplementary Material, so some methodological specifics are not fully contained in the main text (evident from the text).

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1038/ncomms2784

Cites

48 of 48 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Figure 1 Origins of emf in nanoscale cells. These sketches show situations for SiO2-based cells in which one of the three basis origins of emf dominates. (a) A Nernst potential VN of a Ag/SiO2/Pt cell arising from the difference of the chemical potential of Ag metal at the interfaces Ag/electrolyte and Pt/electrolyte ΔμAg=μ′Ag−μ″Ag. The Nernst potential VN according to equation (11) has a negative value and it is given by the difference of the electrical potentials at both electrodes generated to keep the condition ( is the electrochemical potential given by ). Depending on the specific chemical redox system and the chemical potential gradients, the sign of the Vemf can also be positive. (b) A diffusion potential Vd is generated in a Pt/SiO2/Pt cell by gradients of the chemical potentials of the Ag+ and OH− ions, that is, ΔμAg+=μ′Ag+−μ″Ag+ and ΔμOH−=μ′OH−−μ″OH− inhomogeneously distributed in the thin film as given by equation (5). (c) In the case of a nanosize filament, the chemical potential of Ag contains an additional surface energy term generating a chemical potential gradient ΔμAg=μAg-micro−μAg-nano in accordance with equation (6) (Gibbs–Thomson Potential VGT). (d) In the case of a fully metallic contact or a highly conducting tunnel junction, the emf is Vcell=0. The potential of the right electrode is used as a reference throughout the text. Please note that profiles of the electrostatic potential φ is sketched without zooming into the space charge layers.
Figure 1 Origins of emf in nanoscale cells. These sketches show situations for SiO2-based cells in which one of the three basis origins of emf dominates. (a) A Nernst potential VN of a Ag/SiO2/Pt cell arising from the difference of the chemical potential of Ag metal at the interfaces Ag/electrolyte and Pt/electrolyte ΔμAg=μ′Ag−μ″Ag. The Nernst potential VN according to equation (11) has a negative value and it is given by the difference of the electrical potentials at both electrodes generated to keep the condition ( is the electrochemical potential given by ). Depending on the specific chemical redox system and the chemical potential gradients, the sign of the Vemf can also be positive. (b) A diffusion potential Vd is generated in a Pt/SiO2/Pt cell by gradients of the chemical potentials of the Ag+ and OH− ions, that is, ΔμAg+=μ′Ag+−μ″Ag+ and ΔμOH−=μ′OH−−μ″OH− inhomogeneously distributed in the thin film as given by equation (5). (c) In the case of a nanosize filament, the chemical potential of Ag contains an additional surface energy term generating a chemical potential gradient ΔμAg=μAg-micro−μAg-nano in accordance with equation (6) (Gibbs–Thomson Potential VGT). (d) In the case of a fully metallic contact or a highly conducting tunnel junction, the emf is Vcell=0. The potential of the right electrode is used as a reference throughout the text. Please note that profiles of the electrostatic potential φ is sketched without zooming into the space charge layers.CC BY-NC-ND · PubMed Central
Figure 2 Steady-state emf measurements for Ag/SiO2/Pt ECM cells. (a) Simplified equivalent circuit model of a ReRAM device. (b) Vcell for a Ag/SiO2/Pt cell measured under open circuit conditions. The red line curve (1) depicts Vcell in the OFF state after a SET/RESET cycle. For the other curves, the ion concentration cion (that is, the sum of the Ag+ and OH− ion concentrations, averaged over the thickness) was controlled and preset using different sweep rates25. Curve (2) corresponds to cion=1.4 × 10−4 M cm−3, (3) to cion=9.2 × 10−5 M cm−3, (4) to cion=2 × 10−5 M cm−3 and curve (5) to cion=1.7 × 10−5 M cm−3, respectively. Details of the measurements are depicted in Supplementary Fig. S2. Further voltage sweeps in the negative voltage regime result in further decrease of the ion concentration (Supplementary Fig. S3). (c) The slope of the line provides the pre-exponential term and we were thus able to determine the ionic transference number by using equations (10) and z=+1 (for Ag+). (d) The time evolution of the discharge current (for V=0 V) of the cell (diameter d=100 μm) after SET and subsequent RESET operation is shown. Inset: the same plot for an extended time and a log current scale. The integration reveals the charge (5 nC) of the nanobattery.
Figure 2 Steady-state emf measurements for Ag/SiO2/Pt ECM cells. (a) Simplified equivalent circuit model of a ReRAM device. (b) Vcell for a Ag/SiO2/Pt cell measured under open circuit conditions. The red line curve (1) depicts Vcell in the OFF state after a SET/RESET cycle. For the other curves, the ion concentration cion (that is, the sum of the Ag+ and OH− ion concentrations, averaged over the thickness) was controlled and preset using different sweep rates25. Curve (2) corresponds to cion=1.4 × 10−4 M cm−3, (3) to cion=9.2 × 10−5 M cm−3, (4) to cion=2 × 10−5 M cm−3 and curve (5) to cion=1.7 × 10−5 M cm−3, respectively. Details of the measurements are depicted in Supplementary Fig. S2. Further voltage sweeps in the negative voltage regime result in further decrease of the ion concentration (Supplementary Fig. S3). (c) The slope of the line provides the pre-exponential term and we were thus able to determine the ionic transference number by using equations (10) and z=+1 (for Ag+). (d) The time evolution of the discharge current (for V=0 V) of the cell (diameter d=100 μm) after SET and subsequent RESET operation is shown. Inset: the same plot for an extended time and a log current scale. The integration reveals the charge (5 nC) of the nanobattery.CC BY-NC-ND · PubMed Central
Figure 3 Time-dependent emf measurements for Ag/Ge0.3Se0.7/Pt ECM cells. After a SET/RESET cycle (initial state), a negative voltage is applied to the Ag electrode resulting in a dendrite formation. At t1=0 s the voltage measurement is started. Fading of the diffusion potential contribution from t1 to t2 leads to a highly negative Vcell owing to a significant Nernst potential between the electrodes. In parallel to the dissolution of the dendrites (t2), the emf increases to positive values again with a diffusion potential as the remaining component of the emf owing to the different activity of Ag+ ions at the both s′, s″ surfaces (t>t3). The scale bar in the inset corresponds to 20 μm.
Figure 3 Time-dependent emf measurements for Ag/Ge0.3Se0.7/Pt ECM cells. After a SET/RESET cycle (initial state), a negative voltage is applied to the Ag electrode resulting in a dendrite formation. At t1=0 s the voltage measurement is started. Fading of the diffusion potential contribution from t1 to t2 leads to a highly negative Vcell owing to a significant Nernst potential between the electrodes. In parallel to the dissolution of the dendrites (t2), the emf increases to positive values again with a diffusion potential as the remaining component of the emf owing to the different activity of Ag+ ions at the both s′, s″ surfaces (t>t3). The scale bar in the inset corresponds to 20 μm.CC BY-NC-ND · PubMed Central
Figure 4 Emf for different types of ReRAM cells. All tested cells showed an emf varying from some hundreds of microvolts to some hundreds of millivolts (a). The specific steady-state emf depends on the type of cell and the device operation (for example, sweep rate or voltage amplitude before the (open cell) emf measurement). For the sake of completeness, the internal resistance Ri normalized by the total resistance Rtot is given (for details: see Supplementary Table S1). The influence of the emf on the current–voltage sweeps, resulting in non-zero-crossing characteristics (b), is given for the Cu/SiO2/Pt system (red curve) as an example (electrode area Acell=2 × 10−4 cm2, sweep rate ν=400 mV s−1). The I–V characteristics in grey are provided for statistical verification. For the sake of clarity, the currents of the OFF state (A) and (C) and the ON state (B) are labelled, respectively. The formed valence change memory (VCM)-type cells (Ti/SrTiO3/Pt and Ta/Ta2O5/Pt) show lower emf for the OFF state owing to the higher electronic partial conductivity, that is, higher currents, but lower ion transference number. Emfs for VCM cells are depicted in Supplementary Figs S7,S8, respectively. The I–V characteristics for Ag/SiO2/Pt and Ti/SrTiO3/Pt cells are shown in Supplementary Figs S9,S10.
Figure 4 Emf for different types of ReRAM cells. All tested cells showed an emf varying from some hundreds of microvolts to some hundreds of millivolts (a). The specific steady-state emf depends on the type of cell and the device operation (for example, sweep rate or voltage amplitude before the (open cell) emf measurement). For the sake of completeness, the internal resistance Ri normalized by the total resistance Rtot is given (for details: see Supplementary Table S1). The influence of the emf on the current–voltage sweeps, resulting in non-zero-crossing characteristics (b), is given for the Cu/SiO2/Pt system (red curve) as an example (electrode area Acell=2 × 10−4 cm2, sweep rate ν=400 mV s−1). The I–V characteristics in grey are provided for statistical verification. For the sake of clarity, the currents of the OFF state (A) and (C) and the ON state (B) are labelled, respectively. The formed valence change memory (VCM)-type cells (Ti/SrTiO3/Pt and Ta/Ta2O5/Pt) show lower emf for the OFF state owing to the higher electronic partial conductivity, that is, higher currents, but lower ion transference number. Emfs for VCM cells are depicted in Supplementary Figs S7,S8, respectively. The I–V characteristics for Ag/SiO2/Pt and Ti/SrTiO3/Pt cells are shown in Supplementary Figs S9,S10.CC BY-NC-ND · PubMed Central
Figure 5 Classification of mem devices. (a) Memristive, memcapacitive and meminductive devices are assumed to offer pinched characteristics at the origin in general39. In the case of memcapacitive and meminductive devices, a spontaneous polarization of a ferroelectric and ferromagnetic material, respectively, leads for example, to non-zero-crossing characteristics11. Similarly, a non-zero-crossing I–V characteristic of a memristive device indicates the presence of an inherent nanobattery, that is, this device is active. Therefore, we introduce the generic terms extended memristive device, extended memcapacitive device and extended meminductive device to account for both zero-crossing and non-zero-crossing I–V characteristics. Note that the origin of non-zero-crossing behaviour in memcapacitive and meminductive devices is of completely different nature than in memristive devices, thus require specific modifications of the concept. Interestingly, spin-transfer torque (STT) MRAM cells offer zero-crossing in contrast to ReRAM cells, thus can be considered as conventional memristive device. (b) Equivalent circuit of the extended memristive element. The ionic current is defined by the nanobattery, which controls the state-dependent resistor representing the electronic current path. The capacitance of the device is neglected as its influence is not significant. The partial electronic conductivity in the electrolyte induces a state-independent resistance Rleak due to a leakage current in parallel. (c) Simulated I–V characteristic of the extended memristor. The zoom shows the non-zero-crossing behaviour. Further considerations on the simulation are described in Supplementary Note 4.
Figure 5 Classification of mem devices. (a) Memristive, memcapacitive and meminductive devices are assumed to offer pinched characteristics at the origin in general39. In the case of memcapacitive and meminductive devices, a spontaneous polarization of a ferroelectric and ferromagnetic material, respectively, leads for example, to non-zero-crossing characteristics11. Similarly, a non-zero-crossing I–V characteristic of a memristive device indicates the presence of an inherent nanobattery, that is, this device is active. Therefore, we introduce the generic terms extended memristive device, extended memcapacitive device and extended meminductive device to account for both zero-crossing and non-zero-crossing I–V characteristics. Note that the origin of non-zero-crossing behaviour in memcapacitive and meminductive devices is of completely different nature than in memristive devices, thus require specific modifications of the concept. Interestingly, spin-transfer torque (STT) MRAM cells offer zero-crossing in contrast to ReRAM cells, thus can be considered as conventional memristive device. (b) Equivalent circuit of the extended memristive element. The ionic current is defined by the nanobattery, which controls the state-dependent resistor representing the electronic current path. The capacitance of the device is neglected as its influence is not significant. The partial electronic conductivity in the electrolyte induces a state-independent resistance Rleak due to a leakage current in parallel. (c) Simulated I–V characteristic of the extended memristor. The zoom shows the non-zero-crossing behaviour. Further considerations on the simulation are described in Supplementary Note 4.CC BY-NC-ND · PubMed Central

Verification

Claims the paper makes

2 Valid · 0 Not valid · 3 Not checked · 47 Own results and interpretations

33 more claims

Create a free account to see all 52 claims and every source verdict.

See all claims — free account
  • Probably not a substantial claim. 4
  • It may state two separate claims as one. 11

Create a free account to see these claims.

Citations

Cites

Show all 48 references

Research works printed but not linked: 2

  1. Vetter, KJ. Electrochemical Kinetics Springer Verlag (1961).
  2. ITRS. The International Technology Roadmap for Semiconductors— ITRS 2011 Edition 2011..

Cited by

See all 591

Metadata

Authors
Valov, I., Linn, E., Tappertzhofen, S., Schmelzer, S., van den Hurk, J., Lentz, F., & Waser, R.
Affiliations
  • RWTH Aachen University (DE)
  • Forschungszentrum Jülich (DE)
Corresponding author
Valov, I.
Venue
Nature Communications
Published
2013-04-23
Volume
4
Issue
1
Pages
1771-1771
ISSN
2041-1723 (ISSN-L)
OpenAlex
W1975647260
Cited by
587
References
48
Citations by year
2026: 36 · 2025: 28 · 2024: 34 · 2023: 38 · 2022: 42 · 2021: 53 · 2020: 51 · 2019: 51 · 2018: 57 · 2017: 50 · 2016: 56 · 2015: 34 · 2014: 38 · 2013: 19
FWCI
29.36
Type
journal article
Language
en
Open access
Licence
Locations
  • Nature Communications (publishedVersion, cc-by-nc-nd)
  • Europe PMC (PubMed Central) (publishedVersion, cc-by-nc-nd)
  • PubMed Central (publishedVersion, cc-by-nc-nd)
  • PubMed (publishedVersion)
  • arXiv (Cornell University) (submittedVersion)
  • RePEc: Research Papers in Economics (submittedVersion)
  • Cambridge University Engineering Department Publications Database (submittedVersion)
  • JuSER (Forschungszentrum Jülich) (submittedVersion, cc-by-nc-nd)
  • RWTH Publications (RWTH Aachen) (submittedVersion)
  • arXiv (Cornell University)
Funders
  • Samsung Advanced Institute of Technology
  • Deutsche Forschungsgemeinschaft (SFB-917)
  • Samsung
Topics
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced Memory and Neural Computing
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Ferroelectric and Negative Capacitance Devices
  • Physical Sciences › Materials Science › Materials Chemistry › Phase-change materials and chalcogenides
Keywords
nanobatteries, memristors, electromotive force, non-equilibrium states, hysteresis loops, neuromorphic computing, device modeling

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

A language model drew the claims from the paper on 2026-09-29, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-09-29 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.