CoChat

Shaping the topology of folding pathways in mechanical systems

Open access
Stern, Menachem, Jayaram, Viraaj, Murugan, Arvind · 2018 · Nature Communications

The DOI matches its Crossref record; 50 of the 50 references it cites were found in a registry or an index; 4 of the 14 sources its claims cite were checked for support.

Abstract

Disordered mechanical systems, when strongly deformed, have complex configuration spaces with multiple stable states and pathways connecting them. The topology of such pathways determines which states are smoothly accessible from any part of configuration space.

Overview

CoChat Summary

TL;DR

Heterogeneous stiffness in hinges or creases can reshape the topology of folding pathways in mechanical systems by creating saddle-node bifurcations that eliminate undesired modes. This enables robust self-folding of origami and speed-dependent selection among distinct folded states.

Key findings

  • In a 4-bar linkage, unequal joint stiffness lifts different modes unequally; one mode undergoes a saddle-node bifurcation with the transition state at finite folding extent ρ = ρc, making the undesired mode inaccessible from the flat state.
  • For self-folding sheets, LP/QP-designed crease stiffness profiles eliminate exponentially many misfolding modes near the flat state. In simulations of 50 random patterns, stiff patterns achieved a success rate in excess of 90% when folded slowly, compared with an expected <0.1% success rate with free folding creases.
  • A 16-vertex pattern with LP springs produced three completely distinct but reproducible folded structures in slow, intermediate, and fast folding regimes.
  • The bifurcation diagram can make pathways accessible only at specific folding speeds, allowing speed-dependent selection of different folded states.

Methods

  • The paper analyzes canonical models: a 4-bar mechanical linkage, a 4-vertex origami unit, and larger self-folding sheets. Crease or joint stiffness is modeled as a torsional spring relaxed at the flat state, with energy models detailed in Supplementary Notes.
  • Design constraints for lifting an undesired mode are linear in the stiffnesses κi, requiring a saddle-node bifurcation and κi > 0. Energy optimization is formulated as Linear Programming (LP); geometric distortion minimization is formulated as Quadratic Programming (QP).
  • Simulations sampled 50 random patterns with programmed low-energy motions using loop equations, then simulated folding at varying speeds assuming crease hinges follow a first-order relaxation equation with timescale τrelax. External folding torques and target folding angles were also tested.

Limitations

  • The paper states that the saddle-node constraint only ensures absence of undesired modes up to a total folding ρc; beyond that, crease stiffness (~ρ2) becomes less important than face bending (~ρ4), and undesired modes are restored in a series of saddle-node bifurcations.
  • The paper states that adiabatic folding is required for the unique low-ρ minimum to funnel to the desired state, and success rate drops with folding rate. Stiffness heuristics are “useful for slow folding, yet imperfect,” with a small fraction of failed cases where the low-ρ and desired high-ρ modes undergo distinct saddle-node bifurcations at intermediate ρ.
  • Evident from the text: the results are based on theory and simulations, with no experimental validation reported; the design relies on numerically computed modes and transition states near the flat state.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1038/s41467-018-06720-1

Cites

50 of 50 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Fig. 1 Stiff joints in a linkage network can change the connectivity of nonlinear modes in state space. a, b The 4-bar linkage has only one degree of freedom, but two distinct zero energy motions that meet at a branch point at the flat state, making the mechanism difficult to control. The two motions can be seen as minima in the energy landscape at a fixed total strain ρ. c, d We can eliminate a chosen motion in a saddle-node bifurcation at ρc by making the joints stiff to different extents (i.e., adding torsional springs that are relaxed in the flat state; larger orange circles denote stiffer springs). The bifurcation diagram shows that such a stiffness profile changes the connectivity of the two nonlinear modes. One of the two modes is destroyed in a saddle-node bifurcation at ρc and is thus inaccessible from the flat state ρ = 0 (ϕ—angle variable in the two-dimensional linearized null space at the flat state, see Supplementary Note 1)
Fig. 1 Stiff joints in a linkage network can change the connectivity of nonlinear modes in state space. a, b The 4-bar linkage has only one degree of freedom, but two distinct zero energy motions that meet at a branch point at the flat state, making the mechanism difficult to control. The two motions can be seen as minima in the energy landscape at a fixed total strain ρ. c, d We can eliminate a chosen motion in a saddle-node bifurcation at ρc by making the joints stiff to different extents (i.e., adding torsional springs that are relaxed in the flat state; larger orange circles denote stiffer springs). The bifurcation diagram shows that such a stiffness profile changes the connectivity of the two nonlinear modes. One of the two modes is destroyed in a saddle-node bifurcation at ρc and is thus inaccessible from the flat state ρ = 0 (ϕ—angle variable in the two-dimensional linearized null space at the flat state, see Supplementary Note 1)CC BY · PubMed Central
Fig. 2 Heterogeneous stiff creases can simplify the landscape of self-folding sheets near the flat state. a An origami 4-vertex has a choice between two distinct folding modes at the flat state (ϕ—null space angle variable, see Supplementary Note 2). b Stiff creases completely eliminates a chosen mode by combining it with a nearby transition state (TS) in a saddle-node bifurcation (thickness of orange strip indicates stiffness.) c Trade-off: stiff creases distort the desired mode while eliminating undesired modes. Stiffness profiles that minimize energy distortion (e.g., the linear programming (LP) method) cause large geometric distortion and vice versa (e.g., the quadratic programming (QP) method). d The exponentially many misfolding modes of large sheets are all eliminated if the stiffness profile κi satisfies a linear constraint, shown here as a simplex. e We can minimize distortion (energy or geometry) of the desired mode by optimizing crease stiffness on this simplex. f, g All but one chosen minimum in a pattern’s energy landscape (at small overall folding) can be eliminated by stiff creases predicted by the procedure in (e)
Fig. 2 Heterogeneous stiff creases can simplify the landscape of self-folding sheets near the flat state. a An origami 4-vertex has a choice between two distinct folding modes at the flat state (ϕ—null space angle variable, see Supplementary Note 2). b Stiff creases completely eliminates a chosen mode by combining it with a nearby transition state (TS) in a saddle-node bifurcation (thickness of orange strip indicates stiffness.) c Trade-off: stiff creases distort the desired mode while eliminating undesired modes. Stiffness profiles that minimize energy distortion (e.g., the linear programming (LP) method) cause large geometric distortion and vice versa (e.g., the quadratic programming (QP) method). d The exponentially many misfolding modes of large sheets are all eliminated if the stiffness profile κi satisfies a linear constraint, shown here as a simplex. e We can minimize distortion (energy or geometry) of the desired mode by optimizing crease stiffness on this simplex. f, g All but one chosen minimum in a pattern’s energy landscape (at small overall folding) can be eliminated by stiff creases predicted by the procedure in (e)CC BY · PubMed Central
Fig. 3 Stiff creases change the topological connectivity of undesired modes and promote folding at slow speeds. a The energy landscape of a quad with stiff creases has a unique mode at low strain ρ, but becomes more complex at higher strain. b However, slow folding will recover the desired state provided the unique mode at low strain is continuously connected to the desired state and does not undergo a saddle-node bifurcation (blue line). Slow folding can be successful even if the unique mode at small strain ρ is quite distorted relative to the desired mode. c Bifurcation diagram as a function of total folding ρ for a specific 16-vertex pattern shows select undesired modes (solid lines) being eliminated at bifurcations with saddles (dashed lines). Only the desired mode (blue) survives—albeit distorted—to the flat state. d Simulations of folding at a finite strain rate (relative to relaxation timescale of hinges) show high success for slow folding and failures at higher folding speeds (Data from 50 random 16−vertex patterns)
Fig. 3 Stiff creases change the topological connectivity of undesired modes and promote folding at slow speeds. a The energy landscape of a quad with stiff creases has a unique mode at low strain ρ, but becomes more complex at higher strain. b However, slow folding will recover the desired state provided the unique mode at low strain is continuously connected to the desired state and does not undergo a saddle-node bifurcation (blue line). Slow folding can be successful even if the unique mode at small strain ρ is quite distorted relative to the desired mode. c Bifurcation diagram as a function of total folding ρ for a specific 16-vertex pattern shows select undesired modes (solid lines) being eliminated at bifurcations with saddles (dashed lines). Only the desired mode (blue) survives—albeit distorted—to the flat state. d Simulations of folding at a finite strain rate (relative to relaxation timescale of hinges) show high success for slow folding and failures at higher folding speeds (Data from 50 random 16−vertex patterns)CC BY · PubMed Central
Fig. 4 Sheets with stiff creases dramatically improve folding for a wide range of external forces applied to specific creases. We consider folding by (a) different folding torques Fi^ext or (b) springs that target desired fold angles ρi^target for different creases i. a Forces Fi^ext are much more likely to fold into the desired mode with stiff creases (red data) (predicted by linear programming) than with freely folding creases (gray). Even folding forces Fi^ext very poorly aligned with the desired pathway (ρD)i result in the desired pathway (averaged over 5 random 16-vertex patterns, 100 random Fi^ext for each data point). b Patterns folded using springs of given target angle ρi^target on select random creases i. Successful folding into the desired mode is dramatically improved in patterns with stiff (LP predicted) creases compared to free folding creases. Even a single actuator is successful a significant fraction of the time (data averaged over ten random 16-vertex patterns)
Fig. 4 Sheets with stiff creases dramatically improve folding for a wide range of external forces applied to specific creases. We consider folding by (a) different folding torques Fi^ext or (b) springs that target desired fold angles ρi^target for different creases i. a Forces Fi^ext are much more likely to fold into the desired mode with stiff creases (red data) (predicted by linear programming) than with freely folding creases (gray). Even folding forces Fi^ext very poorly aligned with the desired pathway (ρD)i result in the desired pathway (averaged over 5 random 16-vertex patterns, 100 random Fi^ext for each data point). b Patterns folded using springs of given target angle ρi^target on select random creases i. Successful folding into the desired mode is dramatically improved in patterns with stiff (LP predicted) creases compared to free folding creases. Even a single actuator is successful a significant fraction of the time (data averaged over ten random 16-vertex patterns)CC BY · PubMed Central
Fig. 5 Folding speed can controllably select between different folding pathways. a While slow folding follows the continuous deformation of the unique mode at low strain ρ (blue), fast folding results in a state that most “resembles” that low-ρ mode (green). If the unique low-ρ mode is significantly distorted in geometry relative to the slow folding target, slow and fast folding can result in very different outcomes. b, c We systematically attempted folding at different strain rates (relative to a fixed hinge relaxation timescale) for the 16-vertex pattern with stiff creases shown. We find three distinct outcomes at slow, intermediate, fast rates that completely differ in their Mountain-valley states, geometry and energy. The slow folding outcome corresponds to following the blue path in (b) while the intermediate and fast pathways cross over from blue to the magenta and green modes, respectively, at some intermediate folding angles
Fig. 5 Folding speed can controllably select between different folding pathways. a While slow folding follows the continuous deformation of the unique mode at low strain ρ (blue), fast folding results in a state that most “resembles” that low-ρ mode (green). If the unique low-ρ mode is significantly distorted in geometry relative to the slow folding target, slow and fast folding can result in very different outcomes. b, c We systematically attempted folding at different strain rates (relative to a fixed hinge relaxation timescale) for the 16-vertex pattern with stiff creases shown. We find three distinct outcomes at slow, intermediate, fast rates that completely differ in their Mountain-valley states, geometry and energy. The slow folding outcome corresponds to following the blue path in (b) while the intermediate and fast pathways cross over from blue to the magenta and green modes, respectively, at some intermediate folding anglesCC BY · PubMed Central

Verification

Claims the paper makes

3 Valid · 2 Not valid · 5 Not checked · 62 Own results and interpretations

46 more claims

Create a free account to see all 72 claims and to verify the 2 references still open.

See all claims — free account
  • It may state two separate claims as one. 16
  • Borderline: one of the tests for a substantial claim is unclear. 3
  • Probably not a substantial claim. 3

Create a free account to see these claims.

Citations

Cites

Show all 50 references

Research works printed but not linked: 2

  1. Howell L. L. Compliant Mechanisms (John Wiley & Sons, Hoboken, NJ, USA, 2001).
  2. Miura, K. Method of packaging and deployment of large membranes. In Proc. 31st Congr. Int. Astronaut. Fed. (1980).

Cited by

See all 38

Metadata

Authors
Stern, M., Jayaram, V., & Murugan, A.
Affiliations
University of Chicago (US)
Corresponding author
Murugan, Arvind
Venue
Nature Communications
Published
2018-10-16
Volume
9
Issue
1
Pages
4303-4303
ISSN
2041-1723 (ISSN-L)
OpenAlex
W3101869540
Cited by
38
References
49
Citations by year
2026: 2 · 2025: 3 · 2024: 5 · 2023: 8 · 2022: 10 · 2021: 5 · 2020: 2 · 2019: 3
FWCI
1.60
Type
journal article
Language
en
Open access
Licence
Locations
  • Nature Communications (publishedVersion, cc-by)
  • Europe PMC (PubMed Central) (publishedVersion, cc-by)
  • PubMed Central (publishedVersion, cc-by)
  • PubMed (publishedVersion)
  • RePEc: Research Papers in Economics (submittedVersion)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
Funders
National Science Foundation (MRSEC 1420709)
Topics
  • Physical Sciences › Engineering › Mechanical Engineering › Advanced Materials and Mechanics
  • Physical Sciences › Engineering › Mechanical Engineering › Modular Robots and Swarm Intelligence
  • Physical Sciences › Engineering › Civil and Structural Engineering › Structural Analysis and Optimization
Keywords
folding pathways, configuration space topology, bifurcation diagrams, elastic networks, self-folding, linear programming, metamaterials, stable states

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Cited sources are checked with a language model’s help (qwen3.8-omni-flash).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Shaping the topology of folding pathways in mechanical systems. https://app.cochat.ai/papers/10.1038/s41467-018-06720-1
The paper
Stern, M., Jayaram, V., & Murugan, A. (2018). Shaping the topology of folding pathways in mechanical systems. Nature Communications. https://doi.org/10.1038/s41467-018-06720-1

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.