The DOI matches its Crossref record; 46 of the 47 references it cites were found in a registry or an index; 5 of the 27 sources its claims cite were checked for support.
Tunable CoFe-based active sites on 3D heteroatom doped graphene aerogel electrocatalysts via annealing gas regulation for efficient water splitting
Abstract
Tuning CoFe-based active sites on 3D heteroatom doped graphene aerogels facilitates the regulation of the electrocatalytic activity toward the OER and HER, respectively, for efficient water splitting, which is achieved by changing the annealing gas.
Overview
CoChat Summary
TL;DR
A single hydrothermal-plus-pyrolysis route using the same GO/thiourea/Co/Fe precursor yields two graphene-aerogel electrocatalysts whose active sites are tuned by annealing gas: CoFe₂O₄ on N,S-doped rGO in N₂ for OER and amorphous bimetallic CoFe on N-doped rGO in NH₃ for HER. Combined, they drive overall alkaline water splitting at 10 mA cm⁻² and 1.63 V with 100 h stability.
Key findings
- Annealing gas controls phase and doping: N₂ gives CoFeO@N/S-rGO with CoFe₂O₄ nanoparticles and N,S co-doping, while NH₃ gives CoFe@N-rGO with amorphous bimetallic CoFe nanoparticles and N doping but no detectable S.
- For OER in 1.0 M KOH, CoFeO@N/S-rGO shows an onset potential of 1.44 V vs. RHE, an overpotential of 248 mV at 10 mA cm⁻², and a Tafel slope of 40 mV dec⁻¹, outperforming CoFe@N-rGO, CoO@N/S-rGO, Co@N-rGO, and commercial RuO₂.
- For HER in 1.0 M KOH, CoFe@N-rGO shows an onset potential of 89 mV, an overpotential of 116 mV at 10 mA cm⁻², and a Tafel slope of 78 mV dec⁻¹, better than CoFeO@N/S-rGO, CoO@N/S-rGO, and Co@N-rGO.
- A two-electrode electrolyzer using CoFe@N-rGO as cathode and CoFeO@N/S-rGO as anode achieves 10 mA cm⁻² at 1.63 V in 1 M KOH with stability for 100 h; it outperforms Pt/C//RuO₂ above 1.77 V, though Pt/C//RuO₂ requires a lower voltage of 1.56 V at 10 mA cm⁻².
Methods
- Synthesis: GO dispersion mixed with thiourea, Co(NO₃)₂·6H₂O, and Fe(NO₃)₃·9H₂O, hydrothermally treated at 120 °C for 2 h, freeze-dried, then pyrolyzed at 800 °C for 1 h under N₂ or NH₃; comparison samples were annealed at 700 and 900 °C.
- Characterization: XRD, HRTEM, SEM, HAADF-STEM/EDS mapping, XPS, Raman spectroscopy, and N₂ adsorption–desorption isotherms; surface areas were 430 m² g⁻¹ for CoFeO@N/S-rGO and 496 m² g⁻¹ for CoFe@N-rGO.
- Electrochemistry: measurements in 1 M KOH using a three-electrode setup with carbon paper working electrode, graphite rod counter electrode, and Ag/AgCl reference; LSV, Tafel plots, EIS, chronopotentiometry, cycling stability, and gas-yield measurements; overall water splitting tested in a two-electrode configuration.
Limitations
- The paper does not state an explicit limitations section.
- Evident from the text: electrochemical performance is demonstrated only in 1 M KOH, and the overall electrolyzer still requires a higher voltage than Pt/C//RuO₂ at 10 mA cm⁻² (1.63 V vs. 1.56 V), surpassing the noble-metal control only above 1.77 V.
- Evident from the text: stability is tested for 100 h at 10 mA cm⁻², and the study does not report performance under industrially relevant current densities or in non-alkaline electrolytes.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
5 Valid · 0 Not valid · 8 Not checked · 51 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“In contrast, bimetal alloys and their derivatives (e.g., sulphides and phosphides) usually have better catalytic performance for the HER than for the OER.21–23”
What the sources say
- Partly supportedcites [21] sourceExperimental — accuracy not yet measured
The Abstract identifies nickel alloys, MoS₂ and nickel phosphide as active HER catalysts. It does not compare their HER performance with OER performance or establish that bimetal alloys and their derivatives usually perform better for HER than OER. (LLM, conf=0.88)
- Not checked — no full text of the sourcecites [22] source
- Not checked — no full text of the sourcecites [23] source
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Three-dimensional (3D) porous graphene aerogels show great potential for application in water splitting because of their superior conductivity, good mechanical stability, high specic surface area, and multidimensional mass-transfer pathways.10,11”
What the sources say
- Not checked — no full text of the sourcecites [10] source
- Partly supportedcites [11] sourceExperimental — accuracy not yet measured
The Introduction (page not available) links porous 3D carbon architectures and efficient transport to high-performance electrolysis, including reactions relevant to water splitting. The sections on heteroatom-doped graphene and 3D carbon nanostructures (pages not available) describe surface area, mechanical properties, and facilitated electron or ion transport, but do not establish this combination of properties or water-splitting potential specifically for porous graphene aerogels. (LLM, conf=0.84)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Such a geometric connement of nanoparticles within graphene layers is able to enhance their interfacial contact for suppressing the dissolution and agglomeration during the catalytic process.26–28”
What the sources say
- Not checked — no full text of the sourcecites [26] source
- Partly supportedcites [27] sourceExperimental — accuracy not yet measured
The paper’s discussion of lithium-ion batteries (page unavailable) says that confining oxide nanoparticles within carbon shells can address aggregation during charge–discharge cycling; its impedance results also indicate improved electrode contact. It does not report suppression of dissolution or establish these effects during a catalytic process. (LLM, conf=0.88)
- Not checked — no full text of the sourcecites [28] source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“Pyridinic nitrogen is useful for acting as anchoring sites for the growth of nanoparticles due to its coordination capabilities.33,34”
What the sources say
- Supportedcites [33] source
The Results section states that pyridinic groups are expected to anchor the growth of Co₃O₄ nanoparticles because of their coordination capabilities. It also says pyridinic functionalities may coordinate Co centers that act as nucleation centers for nanocube growth. (LLM, conf=0.90)
- Not checked — no full text of the sourcecites [34] source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Herein, we demonstrate a versatile gas-regulated strategy for the preparation of two kinds of graphene-based electrocatalysts for the HER and OER, respectively, by using the same procedure with the same precursor.”
boostedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
45 more claims
Create a free account to see all 64 claims and every source verdict.
- Probably not a substantial claim. 9
- It may state two separate claims as one. 5
- The quote only partly states this claim. 1
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The cited source says what the claim attributes to it.
In the citing paper
“The alkaline water electrolyzer employing CoFeO@N/S-rGO and CoFe@N-rGO aerogels as anode and cathode exhibited cell voltage of 1.63 V at the current density of 10 mA cm−2 along with high stability of 100 hours.”
From Aerogels for Electrocatalytic Hydrogen Production (2024) · cites this paper as [52]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 15730 | J. Mater. Chem. A, 2018, 6, 15728–15737
“Therefore, the faradaic efficiency of CoFe@N-rGO for the HER is demonstrated to be nearly 100%.”
§ 15730 | J. Mater. Chem. A, 2018, 6, 15728–15737
“(f) Gas yield of H2 evolved over the CoFeO@N/S-rGO electrode as a function of time at 30 mA cm�2.”
Citations
Cites
Kibsgaard, J., Chen, Z., Reinecke, B. N., & Jaramillo, T. F. (2012) · Nature Materials · doi:10.1038/nmat3439 · Cited by 3,234
Nanostructured Nickel Phosphide as an Electrocatalyst for the Hydrogen Evolution Reaction
Popczun, E. J., McKone, J. R., Read, C. G., Biacchi, A. J., Wiltrout, A. M., Lewis, N. S., & Schaak, R. E. (2013) · Journal of the American Chemical Society · doi:10.1021/ja403440e · Cited by 2,911
Lai, L., Potts, J. R., Zhan, D., Wang, L., Poh, C. K., Tang, C., Gong, H., Shen, Z., Lin, J., & Ruoff, R. S. (2012) · Energy & Environmental Science · doi:10.1039/c2ee21802j · Cited by 2,277
Wu, Z.-S., Yang, S., Sun, Y., Parvez, K., Feng, X., & Müllen, K. (2012) · Journal of the American Chemical Society · doi:10.1021/ja3030565 · Cited by 2,061
Fei, H., Dong, J., Feng, Y., Allen, C. S., Wan, C., Volosskiy, B., Li, M., Zhao, Z., Wang, Y., Sun, H., et al. (2018) · Nature Catalysis · doi:10.1038/s41929-017-0008-y · Cited by 1,973
Pan, Y., Sun, K., Liu, S., Cao, X., Wu, K., Cheong, W.-C., Chen, Z., Wang, Y., Li, Y., Liu, Y., et al. (2018) · Journal of the American Chemical Society · doi:10.1021/jacs.7b12420 · Cited by 1,942
Atomic cobalt on nitrogen-doped graphene for hydrogen generation
Fei, H., Dong, J., Arellano-Jiménez, M. J., Ye, G., Dong Kim, N., Samuel, E. L. G., Peng, Z., Zhu, Z., Qin, F., Bao, J., et al. (2015) · Nature Communications · doi:10.1038/ncomms9668 · Cited by 1,621
High-Energy MnO2 Nanowire/Graphene and Graphene Asymmetric Electrochemical Capacitors
Wu, Z.-S., Ren, W., Wang, D.-W., Li, F., Liu, B., & Cheng, H.-M. (2010) · ACS Nano · doi:10.1021/nn101754k · Cited by 1,517
Wang, H., Lee, H.-W., Deng, Y., Lu, Z., Hsu, P.-C., Liu, Y., Lin, D., & Cui, Y. (2015) · Nature Communications · doi:10.1038/ncomms8261 · Cited by 1,257
Self-citationYang, S., Feng, X., Ivanovici, S., & Müllen, K. (2010) · Angewandte Chemie International Edition · doi:10.1002/anie.201003485 · Cited by 1,072
Research works printed but not linked: 3
- Zhao, 2017, Adv. Funct. Mater., 27, 1706018
- Wang, 2017, ChemSusChem, 45, 485
- Wang, 2017, Adv. Mater., 29, 1603851
Cited by
Zhang, Y., Fu, J., Zhao, H., Jiang, R., Tian, F., & Zhang, R. (2019) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2019.117899 · Cited by 224
Xu, H., Zhao, L., Liu, X., Huang, Q., Wang, Y., Hou, C., Hou, Y., Wang, J., Dang, F., & Zhang, J. (2020) · Advanced Functional Materials · doi:10.1002/adfm.202006188 · Cited by 171
Self-citationRecent Progress on Bimetallic‐Based Spinels as Electrocatalysts for the Oxygen Evolution Reaction
Olowoyo, J. O., & Kriek, R. J. (2022) · Small · doi:10.1002/smll.202203125 · Cited by 162
Chandrasekaran, S., Khandelwal, M., Fan, D., Sui, L., Chung, J. S., Misra, R. D. K., Yin, P., Kim, E. J., Kim, W., Vanchiappan, A., et al. (2022) · Advanced Energy Materials · doi:10.1002/aenm.202200409 · Cited by 159
Fan, R., Zhou, Y., Li, M.-X., Xie, J., Yu, W., Chi, J., Wang, L., Yu, J., Chai, Y., & Dong, B. (2021) · Chemical Engineering Journal · doi:10.1016/j.cej.2021.131943 · Cited by 134
Metadata
- Authors
- Zhang, B., Wang, H., Zuo, Z., Wang, H., & Zhang, J.
- Affiliations
- Shandong University (CN)
- Corresponding author
- Zhang, Jintao
- Venue
- Journal of Materials Chemistry A
- Publisher
- Royal Society of Chemistry (RSC)
- Published
- 2018
- Volume
- 6
- Issue
- 32
- Pages
- 15728-15737
- ISSN
- 2050-7488 (ISSN-L)
- 2050-7496
- OpenAlex
- W2884720841
- Semantic Scholar
- 05d3abe4ab2c2a02ec579ac23a3318d9618310ab
- Cited by
- 76
- References
- 47
- Citations by year
- 2026: 4 · 2025: 4 · 2024: 8 · 2023: 7 · 2022: 12 · 2021: 14 · 2020: 17 · 2019: 9 · 2018: 1
- FWCI
- 2.37
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Journal of Materials Chemistry A (publishedVersion)
- Funders
- National Natural Science Foundation of China (21503116)
- Topics
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › CO2 Reduction Techniques and Catalysts
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Advanced Photocatalysis Techniques
- Keywords
- oxygen evolution reaction, hydrogen evolution reaction, water splitting, electrocatalysts, 3D porous carbon
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-11, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-11 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.