The DOI matches its Crossref record; 95 of the 95 references it cites were found in a registry or an index; 23 of the 84 sources its claims cite were checked for support.
Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m - b -PLLA n ) multiblock-copolymers and PDLA
Open accessAbstract
Strategic polymer synthesis and blending allows control of stereocomplexation and property fine-tuning in PLA-based materials as shown by correlative characterization.
Overview
CoChat Summary
TL;DR
This study systematically correlates block lengths in P(PCLm-b-PLLAn)x multiblock copolymers and PDLA chain length with crystalline phase formation and mechanical properties in solution-cast blends. Stereocomplex formation depends on PCL segment length as well as PLLA length, with no SC in long-PCL/short-PLLA blends, and SCs act as nucleation points for PCL crystallization while tuning ductility.
Key findings
- SC formation occurred in s/s, s/l, and l/l MBC:PDLA blends but not in l/s P(PCL113-b-PLLA26)24 blends, despite ≥21 wt% PLA; SC formed at PLLA:PDLA ratios from 1:1 up to 1:4. Reported crystallite sizes were SC 5–13 nm (conclusions also state 1–8 nm), PCL 1–20 nm, and HC 1–50 nm; relative crystallinities were SC 6–70%, PCL 2–80%, and HC 3–80%.
- SCs acted as nucleation points for PCL crystallization; SC formation was favored over PLA HC, and the HC peak disappeared when SC formed. Annealing a 90:10 MBC:PDLA56 blend increased crystal size from 4 to 12 nm and relative crystallinity from 20 to 25%, while a 50:50 blend showed no change and only 7–10% SC relative crystallinity.
- Mechanical testing showed tensile strengths up to ~2.8 MPa and elongation at break up to ~750% (table maximum 752%, range 637–768%, for P(PCL121-b-PLLA49)26:PDLA56 90:10). The 70:30 blends had the lowest elongation, while 80:20 and 90:10 compositions with SC crystallites showed the highest ductility; PDLA29 blends showed M_n-dependent ductility, whereas PDLA56 blends were governed more by composition.
- Thermal analysis found SC melting temperatures of 180–200 °C, lower than typical 200–230 °C; PCL melted at 58–63 °C and PLA HC at 140–180 °C. Total absolute crystallinity did not exceed 50%, and PDLA56 had a melting temperature of 157 °C with 66% absolute crystallinity.
Methods
- Four P(PCLm-b-PLLAn)x multiblock copolymers (s/s, s/l, l/s, l/l) and PDLA15/29/56 were synthesized, then solution-cast into films blended at MBC:PDLA ratios from 90:10 to 20:80.
- Characterization used 1H-NMR, GPC, DSC, lab and synchrotron WAXS, POM, AFM, TEM, and tensile testing in a correlative approach.
- WAXS crystallite sizes were calculated with the Scherrer equation; DSC crystallinities were calculated from melting enthalpies; tensile tests were performed at room temperature at 10 mm·min⁻¹, with results reported as average of three tests (table reports median with min–max ranges).
Limitations
- Paper states: SAXS measurements did not yield interpretable results due to insufficient electron density contrast; Scherrer analysis assumes isotropic crystallites and provides only approximate average crystallite sizes without orientation or amorphous-fraction information.
- Paper states: slow solvent evaporation may shift crystallization toward HC formation; annealing only increased SC content in samples that already contained SCs; some samples had inhomogeneities, and excessive outliers were excluded from mechanical analysis.
- Evident from text: mechanical data are based on only three tests per sample, limiting statistical power, and the accepted manuscript contains duplicated/placeholder text and some inconsistent crystallite-size reporting.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
7 Valid · 19 Not valid · 38 Not checked · 220 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Moreover, the PCL block size required for crystallization increased to more than 2000 g/mol when PLLA was crystalline.20”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > 1. Introduction
What the sources say
- Could not verifycites [20] 20. Brizzolara, D.; Cantow, H.-J.; Diederichs, K.; Keller, E.; Domb, A. J. Mechanism of the stereocomplex formation between enantiomeric poly (lactide) s. Macromolecules 1996, 29 (1), 191- 197. sourceExperimental — accuracy not yet measured
The Results and Discussion and Experimental Section (page not provided) describe crystallization of PLLA and PDLA, not PCL blocks. Searches for PCL, poly(caprolactone), and a 2000 g/mol crystallization threshold found no passage addressing the claim. (LLM, conf=0.75)
states a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Additionally, PLLA and its enantiomer PDLA can form a stereocomplex (sc-PLA).”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > 1. Introduction
What the sources say
- Could not verifycites [8] 8. Rydz, J.; Sikorska, W.; Kyulavska, M.; Christova, D. Polyester-based (bio) degradable polymers as environmentally friendly materials for sustainable development. International journal of molecular sciences 2014, 16 (1), 564-596. sourceExperimental — accuracy not yet measured
Section 4.1, Table 1 identifies PLLA as poly(l-lactide) and PDLA as poly(d-lactide), but does not say they form a stereocomplex. Searches for “stereocomplex” and for blends of the two polymers found no passage in our copy addressing stereocomplex formation; page numbers were not available. (LLM, conf=0.72)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“The structure-phase and structure-property relations in multiblock copolymers (MBCs) of PLA are not fully understood, compared to homopolymers, copolymers and DCs, though studies on other MBCs suggest similarities as well as peculiarities of MBCs compared to diblock copolymers.8,17,21”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > 1. Introduction
What the sources say
- Could not verifycites [8] 8. Rydz, J.; Sikorska, W.; Kyulavska, M.; Christova, D. Polyester-based (bio) degradable polymers as environmentally friendly materials for sustainable development. International journal of molecular sciences 2014, 16 (1), 564-596. sourceExperimental — accuracy not yet measured
Section 4.2 (page unavailable) says PLA architecture and crystallinity affect material properties, but it does not assess how well structure–phase or structure–property relations are understood for PLA multiblock copolymers. Searches for multiblock copolymers, diblock comparisons, and the claimed knowledge gap found no passage addressing that comparison. (LLM, conf=0.74)
- Not checked — no full text of the sourcecites [17] 17. Zhou, X.; Deng, J.; Fang, C.; Lei, W.; Song, Y.; Zhang, Z.; Huang, Z.; Li, Y. Additive manufacturing of CNTs/PLA composites and the correlation between microstructure and functional properties. Journal of Materials Science & Technology 2021, 60, 27-34. source
- Not checked — no full text of the sourcecites [21] 21. Jikei, M.; Takeyama, Y.; Yamadoi, Y.; Shinbo, N.; Matsumoto, K.; Motokawa, M.; Ishibashi, K.; Yamamoto, F. Synthesis and properties of Poly (L-lactide)-Poly (ɛ-caprolactone) multiblock copolymers by the self-polycondensation of diblock macromonomers. Polymer Journal 2015, 47 (10), 657-665. source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“When SC formation takes place, visible due to the peaks at 12° and 24°, the HC crystallization peak disappears (e.g. Figure 2B 50:50).”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > Materials Advances Accepted Manuscript
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The WAXS graphs exhibit a peak at 17.2° indicating partial crystallization of HC as α-phase (ordered α crystal).”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > DOI: 10.1039/D5MA00886G
hedgedstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
128 more claims
Create a free account to see all 284 claims and every source verdict.
- Probably not a substantial claim. 61
- It may state two separate claims as one. 106
- Borderline: one of the tests for a substantial claim is unclear. 1
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
“P(PCL 113b-PLLA 26 ) 24 blended with PDL 29 .In contrast, the MBC investigated by Jikei et al., consisting of PLLA 22 -b-PCL 49 mixed with PDLA 27 , demonstrated stereocomplex (SC) formation at a 1:1 molar ratio.25 Both systems exhibit a comparable PCL-to-PLLA block length ratio of approximately 2:1.”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > Materials Advances Accepted Manuscript
Reported 2 · recomputed 4.346154
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > Stereocomplex formation depends on PCL segment length
“Interestingly, no SC formation occurs in any of the blends”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > DOI: 10.1039/D5MA00886G
“P(PCL 113 -b-PLLA 26 ) 24: PDLA 56 , in which no diffraction peaks of PLA-HC are visible, but diffraction peaks of SC at 12.4, 20.8 and 24° can be observed for 90/10 mixture.”
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > Stereocomplex formation depends on PCL segment length
“no SC formation was observed in the combination of long PCL blocks with short PLA blocks l/s (Figure 2 C).”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > DOI: 10.1039/D5MA00886G
“in which no diffraction peaks of PLA-HC are visible, but diffraction peaks of SC at 12.4, 20.8 and 24° can be observed for 90/10 mixture.”
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
“In the present study, the long/short multiblock copolymer (l/s MBC) is composed of P(PCL 113b-PLLA 26 ) 24 blended with PDL 29 .In contrast, the MBC investigated by Jikei et al., consisting of PLLA 22 -b-PCL 49 mixed with PDLA 27 , demonstrated stereocomplex (SC) formation at a 1:1 molar ratio.25 Both systems exhibit a comparable PCL-to-PLLA block length ratio of approximately 2:1.”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > Materials Advances Accepted Manuscript
Reported 2 · recomputed 4.346154
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > Materials Advances Accepted Manuscript
“Crystallite sizes vary with the composition between 1-8 nm (SC), 1-20 nm (PCL) and 1-50 nm (HC)”
§ Correlative characterization of stereocomplex formation in blends of aliphatic polyester P(PCL m -b-PLLA n ) multiblock-copolymers and PDLA > DOI: 10.1039/D5MA00886G
“The SC crystallite size found in the P(PCL m -b-PLLA n ) x :PDLA 56 blends were between 5 and 13 nm.The largest SC crystallites of ~13 nm in this series were found in the s/l P(PCL 66 -b-PLLA 32 ) 43 and l/l P(PCL 121 -b-PLLA 49 ) 26 MBCs”
6 more findings
Create a free account to see every finding of this check.
Citations
Cites
The Scherrer equation versus the 'Debye-Scherrer equation'
Holzwarth, U., & Gibson, N. (2011) · Nature Nanotechnology · doi:10.1038/nnano.2011.145 · Cited by 3,407
Stereocomplex formation between enantiomeric poly(lactides)
Ikada, Y., Jamshidi, K., Tsuji, H., & Hyon, S. H. (1987) · Macromolecules · doi:10.1021/ma00170a034 · Cited by 1,409
Poly(lactide) Stereocomplexes: Formation, Structure, Properties, Degradation, and Applications
Tsuji, H. (2005) · Macromolecular Bioscience · doi:10.1002/mabi.200500062 · Cited by 1,366
A note on single crystals in polymers: Evidence for a folded chain configuration
Keller, A. (1957) · Philosophical Magazine · doi:10.1080/14786435708242746 · Cited by 1,019
Crescenzi, V., Manzini, G., Calzolari, G., & Borri, C. (1972) · European Polymer Journal · doi:10.1016/0014-3057(72)90109-7 · Cited by 750
Precise calculation of crystallite size of nanomaterials: A review
Hassanzadeh-Tabrizi, S. A. (2023) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2023.171914 · Cited by 649
Aliphatic Polyester Block Polymers: Renewable, Degradable, and Sustainable
Hillmyer, M. A., & Tolman, W. B. (2014) · Accounts of Chemical Research · doi:10.1021/ar500121d · Cited by 635
Relaxation processes in crystalline polymers: experimental behaviour — a review
Boyd, R. H. (1985) · Polymer · doi:10.1016/0032-3861(85)90192-2 · Cited by 624
Mechanism of the Stereocomplex Formation between Enantiomeric Poly(lactide)s
Brizzolara, D., Cantow, H.-J., Diederichs, K., Keller, E., & Domb, A. J. (1996) · Macromolecules · doi:10.1021/ma951144e · Cited by 547
Tsuji, H., & Ikada, Y. (1999) · Polymer · doi:10.1016/s0032-3861(99)00004-x · Cited by 545
Room temperature polyesterification
Moore, J. S., & Stupp, S. I. (1990) · Macromolecules · doi:10.1021/ma00203a013 · Cited by 516
Super tough poly(lactic acid) blends: a comprehensive review
Zhao, X., Hu, H., Wang, X., Yu, X., Zhou, W., & Peng, S. (2020) · RSC Advances · doi:10.1039/d0ra01801e · Cited by 465
Functional aliphatic polyesters for biomedical and pharmaceutical applications
Seyednejad, H., Ghassemi, A. H., van Nostrum, C. F., Vermonden, T., & Hennink, W. E. (2011) · Journal of Controlled Release · doi:10.1016/j.jconrel.2010.12.016 · Cited by 425
Designing biodegradable multiblock PCL/PLA thermoplastic elastomers
Cohn, D., & Hotovely Salomon, A. (2005) · Biomaterials · doi:10.1016/j.biomaterials.2004.07.052 · Cited by 355
The frustrated structure of poly( l -lactide)
Puiggali, J., Ikada, Y., Tsuji, H., Cartier, L., Okihara, T., & Lotz, B. (2000) · Polymer · doi:10.1016/s0032-3861(00)00235-4 · Cited by 333
Dell'Erba, R., Groeninckx, G., Maglio, G., Malinconico, M., & Migliozzi, A. (2001) · Polymer · doi:10.1016/s0032-3861(01)00269-5 · Cited by 318
Rydz, J., Sikorska, W., Kyulavska, M., & Christova, D. (2014) · International Journal of Molecular Sciences · doi:10.3390/ijms16010564 · Cited by 303
Influence of crystal polymorphism on mechanical and barrier properties of poly(l-lactic acid)
Cocca, M., Lorenzo, M. L. D., Malinconico, M., & Frezza, V. (2011) · European Polymer Journal · doi:10.1016/j.eurpolymj.2011.02.009 · Cited by 296
Pan, P., Han, L., Bao, J., Xie, Q., Shan, G., & Bao, Y. (2015) · The Journal of Physical Chemistry B · doi:10.1021/acs.jpcb.5b03546 · Cited by 231
Effects of crystalline microstructure on drug release behavior of poly(ε-caprolactone) microspheres
Jeong, J.-C., Lee, J., & Cho, K. (2003) · Journal of Controlled Release · doi:10.1016/s0168-3659(03)00367-5 · Cited by 209
Crystalline Morphology of Electrospun Poly(ε-caprolactone) (PCL) Nanofibers
Wang, X., Zhao, H., Turng, L.-S., & Li, Q. (2013) · Industrial & Engineering Chemistry Research · doi:10.1021/ie302185e · Cited by 203
Effect of Molecular Weight on the Crystallization and Melt Memory of Poly(ε-caprolactone) (PCL)
Fernández-Tena, A., Pérez-Camargo, R. A., Coulembier, O., Sangroniz, L., Aranburu, N., Guerrica-Echevarria, G., Liu, G., Wang, D., Cavallo, D., & Müller, A. J. (2023) · Macromolecules · doi:10.1021/acs.macromol.3c00234 · Cited by 200
Thermal degradation behaviour of poly(lactic acid) stereocomplex
Fan, Y., Nishida, H., Shirai, Y., Tokiwa, Y., & Endo, T. (2004) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2004.03.001 · Cited by 199
Isothermal cold crystallization kinetics of polylactide/nucleating agents
Liao, R., Yang, B., Yu, W., & Zhou, C. (2007) · Journal of Applied Polymer Science · doi:10.1002/app.25733 · Cited by 199
Tsuji, H., & Tezuka, Y. (2004) · Biomacromolecules · doi:10.1021/bm049835i · Cited by 194
Mareau, V. H., & Prud'homme, R. E. (2005) · Macromolecules · doi:10.1021/ma0482359 · Cited by 193
Effect of nucleating agents on crystallinity and properties of poly (lactic acid) (PLA)
Aliotta, L., Cinelli, P., Coltelli, M. B., Righetti, M. C., Gazzano, M., & Lazzeri, A. (2017) · European Polymer Journal · doi:10.1016/j.eurpolymj.2017.04.041 · Cited by 183
Calorimetric analysis of the multiple melting behavior of poly(L‐lactic acid)
Di Lorenzo, M. L. (2006) · Journal of Applied Polymer Science · doi:10.1002/app.23136 · Cited by 178
Microstructural aspects of failure in semicrystalline polymers
Schultz, J. M. (1984) · Polymer Engineering & Science · doi:10.1002/pen.760241007 · Cited by 176
de Jong, S. J., van Dijk-Wolthuis, W. N. E., Kettenes-van den Bosch, J. J., Schuyl, P. J. W., & Hennink, W. E. (1998) · Macromolecules · doi:10.1021/ma980553i · Cited by 172
Tashiro, K., Kouno, N., Wang, H., & Tsuji, H. (2017) · Macromolecules · doi:10.1021/acs.macromol.7b01468 · Cited by 143
Crystallization behavior of PCL in hybrid confined environment
Jiang, S., Ji, X., An, L., & Jiang, B. (2001) · Polymer · doi:10.1016/s0032-3861(00)00565-6 · Cited by 137
Evidence of a dual network/spherulitic crystalline morphology in PLA stereocomplexes
Saeidlou, S., Huneault, M. A., Li, H., Sammut, P., & Park, C. B. (2012) · Polymer · doi:10.1016/j.polymer.2012.10.030 · Cited by 120
Remarkable melting behavior of PLA stereocomplex in linear PLLA/PDLA blends
Shao, J., Xiang, S., Bian, X., Sun, J., Li, G., & Chen, X. (2015) · Industrial & Engineering Chemistry Research · doi:10.1021/ie504484b · Cited by 113
Effect of the molecular weight on the crystallinity of PCL-b-PLLA di-block copolymers
Peponi, L., Navarro-Baena, I., Báez, J. E., Kenny, J. M., & Marcos-Fernández, A. (2012) · Polymer · doi:10.1016/j.polymer.2012.07.066 · Cited by 109
Designing Biodegradable Shape Memory Polymers for Tissue Repair
Ramaraju, H., Akman, R. E., Safranski, D. L., & Hollister, S. J. (2020) · Advanced Functional Materials · doi:10.1002/adfm.202002014 · Cited by 108
Crystalline morphology of PLA/clay nanocomposite films and its correlation with other properties
Das, K., Ray, D., Banerjee, I., Bandyopadhyay, N. R., Sengupta, S., Mohanty, A. K., & Misra, M. (2010) · Journal of Applied Polymer Science · doi:10.1002/app.32345 · Cited by 103
Zhou, X., Deng, J., Fang, C., Lei, W., Song, Y., Zhang, Z., Huang, Z., & Li, Y. (2021) · Journal of Materials Science & Technology · doi:10.1016/j.jmst.2020.04.038 · Cited by 103
Sun, C., Zheng, Y., Xu, S., Ni, L., Li, X., Shan, G., Bao, Y., & Pan, P. (2021) · ACS Macro Letters · doi:10.1021/acsmacrolett.1c00394 · Cited by 100
Lactide: Production Routes, Properties, and Applications
Cunha, B. L. C., Bahú, J. O., Xavier, L. F., Crivellin, S., de Souza, S. D. A., Lodi, L., Jardini, A. L., Filho, R. M., Schiavon, M. I. R. B., Concha, V. O. C., et al. (2022) · Bioengineering · doi:10.3390/bioengineering9040164 · Cited by 97
Kurz, R., Schulz, M., Scheliga, F., Men, Y., Seidlitz, A., Thurn-Albrecht, T., & Saalwächter, K. (2018) · Macromolecules · doi:10.1021/acs.macromol.8b00809 · Cited by 86
Morphology, Crystallinity, and Molecular Weight of Poly(ε-caprolactone)/Graphene Oxide Hybrids
Castilla-Cortázar, I., Vidaurre, A., Marí, B., & Campillo-Fernández, A. J. (2019) · Polymers · doi:10.3390/polym11071099 · Cited by 86
Zhou, C., Li, H., Zhang, W., Li, J., Huang, S., Meng, Y., Christiansen, J. D., Yu, D., Wu, Z., & Jiang, S. (2016) · Polymer · doi:10.1016/j.polymer.2016.03.014 · Cited by 85
Park, H.-S., & Hong, C.-K. (2021) · Polymers · doi:10.3390/polym13111851 · Cited by 85
Effect of Biomass as Nucleating Agents on Crystallization Behavior of Polylactic Acid
Shi, K., Liu, G., Sun, H., Yang, B., & Weng, Y. (2022) · Polymers · doi:10.3390/polym14204305 · Cited by 85
Crystal polymorphism of polylactide and its composites by X-ray diffraction study
Hsieh, Y.-T., Nozaki, S., Kido, M., Kamitani, K., Kojio, K., & Takahara, A. (2020) · Polymer Journal · doi:10.1038/s41428-020-0343-8 · Cited by 84
Xiong, Z., Liu, G., Zhang, X., Wen, T., de Vos, S., Joziasse, C., & Wang, D. (2013) · Polymer · doi:10.1016/j.polymer.2012.11.076 · Cited by 83
Spontak, R. J., & Smith, S. D. (2001) · Journal of Polymer Science Part B: Polymer Physics · doi:10.1002/polb.1070 · Cited by 83
Morphological study of biodegradable PEO/PLA block copolymers
Younes, H., & Cohn, D. (1987) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820211103 · Cited by 82
Woo, E. M., & Chang, L. (2011) · Polymer · doi:10.1016/j.polymer.2011.11.002 · Cited by 82
Poly(lactic acid) stereocomplexes based molecular architectures: Synthesis and crystallization
Michell, R. M., Ladelta, V., Da Silva, E., Müller, A. J., & Hadjichristidis, N. (2023) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2023.101742 · Cited by 77
Wang, J.-L., & Dong, C.-M. (2006) · Polymer · doi:10.1016/j.polymer.2006.02.047 · Cited by 64
Liu, J., Qi, X., Feng, Q., & Lan, Q. (2020) · Macromolecules · doi:10.1021/acs.macromol.0c00112 · Cited by 60
Tsuji, H., & Bouapao, L. (2012) · Polymer International · doi:10.1002/pi.3219 · Cited by 59
Recent Progress in Understanding Polymer Crystallization
Saalwächter, K., Thurn‐Albrecht, T., & Paul, W. (2023) · Macromolecular Chemistry and Physics · doi:10.1002/macp.202200424 · Cited by 55
Tin( ii ) 2-ethylhexanoate catalysed methanolysis of end-of-life poly(lactide)
Hofmann, M., Alberti, C., Scheliga, F., Meißner, R. R. R., & Enthaler, S. (2020) · Polymer Chemistry · doi:10.1039/d0py00292e · Cited by 52
He, Y., Liu, D., Wang, J., Pan, P., & Hu, W. (2022) · Macromolecules · doi:10.1021/acs.macromol.2c00457 · Cited by 52
Nanoscale artifacts in RuO4-stained poly(styrene)
Chou, T. M., Prayoonthong, P., Aitouchen, A., & Libera, M. (2002) · Polymer · doi:10.1016/s0032-3861(01)00767-4 · Cited by 50
Di Lorenzo, M. L., Rubino, P., Immirzi, B., Luijkx, R., Hélou, M., & Androsch, R. (2015) · Colloid and Polymer Science · doi:10.1007/s00396-015-3709-2 · Cited by 49
Preparation and morphology of multiblock copolymers of the (AB)n type
Matsushita, Y., Mogi, Y., Mukai, H., Watanabe, J., & Noda, I. (1994) · Polymer · doi:10.1016/0032-3861(94)90686-6 · Cited by 47
Recent advances on the structure–properties relationship of multiblock copolymers
Baeza, G. P. (2021) · Journal of Polymer Science · doi:10.1002/pol.20210406 · Cited by 47
Fernández, J., Larrañaga, A., Etxeberria, A., Wang, W., & Sarasua, J. R. (2014) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.35036 · Cited by 45
Haas, S., Sun, X., Conceição, A. L. C., Horbach, J., & Pfeffer, S. (2023) · Journal of Synchrotron Radiation · doi:10.1107/s1600577523008603 · Cited by 43
Self-citationWang, X., Mi, J., Wang, J., Zhou, H., & Wang, X. (2018) · RSC Advances · doi:10.1039/c8ra07510g · Cited by 39
Combined effect of nucleating agent and plasticizer on the crystallization behaviour of polylactide
Anakabe, J., Zaldua Huici, A. M., Eceiza, A., Arbelaiz, A., & Avérous, L. (2017) · Polymer Bulletin · doi:10.1007/s00289-017-1989-z · Cited by 38
Nguyen, H. K., Ito, M., & Nakajima, K. (2016) · Japanese Journal of Applied Physics · doi:10.7567/jjap.55.08nb06 · Cited by 35
Ojha, U., Kulkarni, P. P., Singh, J., & Faust, R. (2009) · Journal of Polymer Science Part A Polymer Chemistry · doi:10.1002/pola.23428 · Cited by 33
Jikei, M., Takeyama, Y., Yamadoi, Y., Shinbo, N., Matsumoto, K., Motokawa, M., Ishibashi, K., & Yamamoto, F. (2015) · Polymer Journal · doi:10.1038/pj.2015.49 · Cited by 33
Liu, Z., Fu, M., Ling, F., Sui, G., Bai, H., Zhang, Q., & Fu, Q. (2019) · Polymer · doi:10.1016/j.polymer.2019.02.029 · Cited by 33
Jing, Z., Shi, X., Zhang, G., & Gu, J. (2017) · Polymer · doi:10.1016/j.polymer.2017.06.019 · Cited by 32
Effect of liquid plasticizers on crystallization of PCL in soft PVC/PCL/plasticizer blends
Xu, Y., Xiong, Y., & Guo, S. (2020) · Journal of Applied Polymer Science · doi:10.1002/app.48803 · Cited by 31
Takagi, A., Hsu, Y.-I., & Uyama, H. (2023) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2023.110564 · Cited by 28
Extended-chain crystallization and stereocomplex formation of polylactides in a Langmuir monolayer
Watanabe, K., & Kumaki, J. (2020) · Polymer Journal · doi:10.1038/s41428-020-0312-2 · Cited by 27
Molecular Weight Determination by N.m.r. Spectroscopy
Barcza, S. (1963) · The Journal of Organic Chemistry · doi:10.1021/jo01042a515 · Cited by 25
Izraylit, V., Gould, O. E. C., Rudolph, T., Kratz, K., & Lendlein, A. (2020) · Biomacromolecules · doi:10.1021/acs.biomac.9b01279 · Cited by 25
Tsuji, H., Yamasaki, M., & Arakawa, Y. (2021) · Macromolecules · doi:10.1021/acs.macromol.1c01099 · Cited by 25
TEM morphological analysis of biopolymers: The case of Poly (Lactic Acid) (PLA)
Molinari, G., Parlanti, P., Aliotta, L., Lazzeri, A., & Gemmi, M. (2023) · Materials Today Communications · doi:10.1016/j.mtcomm.2023.107868 · Cited by 25
Yin, Y., Liu, G., Song, Y., Zhang, X., de Vos, S., Wang, R., Joziasse, C. A. P., & Wang, D. (2016) · European Polymer Journal · doi:10.1016/j.eurpolymj.2016.05.033 · Cited by 24
Monte Carlo simulations of stereocomplex formation in multiblock copolymers
Qiu, X., Liu, R., Nie, Y., Liu, Y., Liang, Z., Yang, J. H., Zhou, Z., & Hao, T. (2019) · Physical Chemistry Chemical Physics · doi:10.1039/c9cp02070e · Cited by 23
Self-citationJing, Z., Huang, X., Liu, X., Liao, M., Zhang, Z., & Li, Y. (2022) · RSC Advances · doi:10.1039/d2ra00461e · Cited by 23
Crystallization and Stereocomplexation of PLA-mb-PBS Multi-Block Copolymers
D’Ambrosio, R., Michell, R., Mincheva, R., Hernández, R., Mijangos, C., Dubois, P., & Müller, A. (2017) · Polymers · doi:10.3390/polym10010008 · Cited by 22
Li, F., Zhou, F., Romano, D., & Rastogi, S. (2023) · Macromolecules · doi:10.1021/acs.macromol.2c02303 · Cited by 21
Crystallization behavior of diblock copolymers based on PCL and PLLA biopolymers
Navarro-Baena, I., Marcos-Fernández, Á. A., Kenny, J. M., & Peponi, L. (2014) · Journal of Applied Crystallography · doi:10.1107/s1600576714022468 · Cited by 20
Remanan, S., Ghosh, S., Das, T. K., & Das, N. C. (2020) · Nano-Structures & Nano-Objects · doi:10.1016/j.nanoso.2020.100487 · Cited by 20
Xie, Y., Yu, W., Xia, T., O’Reilly, R. K., & Dove, A. P. (2023) · Macromolecules · doi:10.1021/acs.macromol.3c00653 · Cited by 20
Jikei, M., Suga, T., Yamadoi, Y., & Matsumoto, K. (2017) · Polymer Journal · doi:10.1038/pj.2016.126 · Cited by 18
The Block Copolymer Phase Behavior Database
Rebello, N. J., Arora, A., Mochigase, H., Lin, T.-S., Shi, J., Audus, D. J., Muckley, E. S., Osmani, A., & Olsen, B. D. (2024) · Journal of Chemical Information and Modeling · doi:10.1021/acs.jcim.4c00242 · Cited by 12
Enhanced proliferation of HeLa cells on PLLA-PCL and PLGA-PCL multiblock copolymers
Suga, T., Xuyen, N. T., Matsumoto, K., Jikei, M., Takahashi, K., Kubota, H., & Tamura, T. (2017) · Polymer Journal · doi:10.1038/pj.2017.21 · Cited by 11
Deformation of Poly-l-lactid acid (PLLA) under Uniaxial Tension and Plane-Strain Compression
Vozniak, A., & Bartczak, Z. (2021) · Polymers · doi:10.3390/polym13244432 · Cited by 11
Soft, Formstable (Co)Polyester Blend Elastomers
Neffe, A., Izraylit, V., Hommes-Schattmann, P., & Lendlein, A. (2021) · Nanomaterials · doi:10.3390/nano11061472 · Cited by 9
Self-citationDai, S., Dai, Z., Jiang, N., Ning, Z., & Gan, Z. (2022) · Polymer · doi:10.1016/j.polymer.2022.125482 · Cited by 8
Probing Organic Thin Films by Coherent X-ray Imaging and X-ray Scattering
Patil, N., Narayanan, T., Michels, L., Skjønsfjell, E. T. B., Guizar-Sicairos, M., Van den Brande, N., Claessens, R., Van Mele, B., & Breiby, D. W. (2019) · ACS Applied Polymer Materials · doi:10.1021/acsapm.9b00324 · Cited by 6
Shahnooshi, M., Schneider, K., Javadi, A., & Altstädt, V. (2023) · Polymer · doi:10.1016/j.polymer.2023.126254 · Cited by 6
Deep Learning to Predict Structure-Property Relationships of Polymer Blends
Yablon, D. G., Chakraborty, I., Passino, H. L., et al. (2022) · ACS symposium series · doi:10.1021/bk-2022-1416.ch003 · Cited by 1
Fernández, J., Larrañaga, A., Etxeberria, A., et al. (2013) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbma.35036 · Cited by 1
Cited by
Baer, A. L., Clarke, R. W., Gowda, R. R., Hesse, S. A., Crowley, M., Xu, S., Hamernik, L. J., Curley, J. B., Urgun-Demirtas, M., Tassone, C. J., et al. (2026) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.6c00712 · Cited by 2
Lu, H., Gong, L., Cao, B., & Bao, J. (2026) · Journal of Polymer Science · doi:10.1002/pola.70111
Improving interlayer adhesion of 3D printed PLA/PCL blends using triblock copolymers
Rachmani, O., Zaltsman, I., Otorgust, G., Mizrahi, L., Ophir, A., Kol, M., & Amir, E. (2026) · Progress in Additive Manufacturing · doi:10.1007/s40964-026-01643-6 · Cited by 1
Nifant'ev, I. E., & Ivchenko, P. V. (2026) · European Polymer Journal · doi:10.1016/j.eurpolymj.2026.114863
Hu, M., Kong, X., & Qian, J. (2026) · Acta Mechanica Sinica · doi:10.1007/s10409-025-25925-x
Metadata
- Authors
- Mandlule, A., Liu, Y., Schwanz, S., Pieper, Y., Scharf, H., Iskhakova, K., Conceição, A. L. C., Wieland, D. C. F., Zeller-Plumhoff, B., Toma, F. M., & Neffe, A. T.
- Affiliations
- Helmholtz-Zentrum Hereon (DE)
- Karlsruhe Institute of Technology (DE)
- Deutsches Elektronen-Synchrotron DESY (DE)
- Helmholtz-Zentrum Hereon, Institute of Metallic Biomaterials, Max-Planck-Str. 1, 21502 Geesthacht, Germany
- Helmut Schmidt University (DE)
- ORCID
- Venue
- Materials Advances
- Publisher
- Royal Society of Chemistry (RSC)
- Published
- 2026
- Volume
- 7
- Issue
- 1
- Pages
- 377-402
- ISSN
- 2633-5409 (ISSN-L)
- OpenAlex
- W4416392925
- Cited by
- 6
- References
- 94
- Citations by year
- 2026: 6
- FWCI
- 1.25
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Materials Advances (publishedVersion, cc-by)
- Funders
- Helmholtz-Gemeinschaft (Joint Lab “Model and Data Driven Materials Characterization)
- Deutsches Elektronen-Synchrotron (Beamline proposal 20231350)
- Topics
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
- Physical Sciences › Materials Science › Materials Chemistry › Block Copolymer Self-Assembly
- Keywords
- stereocomplex formation, polycaprolactone, poly(L-lactic acid), multiblock copolymers, polylactic acid, polymer blends
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-09-28, under version 3 of the claim definition (prompt extract-v3).
A second model labelled each claim on 2026-09-28 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.