The DOI matches its Crossref record.
Effect of annealing temperature and time on the microstructure, mechanical properties and conductivity of cold-rolled explosive Cu/Al composite sheets
Open accessAbstract
Abstract The 1.5 mm thick Cu/Al composite sheet was obtained after explosive-welding and 6 passes cold rolling. The effects of annealing temperature and time on the microstructure, mechanical properties, and conductivity of cold-rolled Cu/Al composite sheets were investigated. The results show that the thickness of the interface diffusion layer with compounds of Al 2 Cu, AlCu, and Al 4 Cu 9 increases with the increase in annealing temperature and holding time, and the total activation energy is 108 kJ mol −1 . The tensile strength of composite sheets decreases and the fracture elongation increases with the increase of annealing temperature. Especially when the annealing temperature increased from 300 ℃ to 350 ℃, the tensile yield strength decreased from 225 MPa to 77 MPa, and the elongation increased from 16% to 37.5%. The tensile-shear strength of composite sheets reaches to 117 MPa after annealing at 400 ℃ for 2 h. The conductivity of composite sheet is greatly affected by the annealing time. At the annealing temperature of 350 ℃ and time of 4 h, the composite sheets show a better conductivity of 96.4% IACS.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“Depending on the thermal impact, these differ in their formation type and thickness.”
From Investigation of the Microstructure and Properties of Aluminum–Copper Compounds Fabricated by the High-Pressure Die Casting Process (2022) · cites this paper as [1]
Experimental — accuracy not yet measuredThe cited source says what the claim attributes to it.
In the citing paper
“Li et al. [1] showed this relationship in their investigations by means of annealing experiments.Thereby, a formation and growth of the intermetallic phases dependent on the annealing time, as well as temperature, could be detected.”
From Investigation of the Microstructure and Properties of Aluminum–Copper Compounds Fabricated by the High-Pressure Die Casting Process (2022) · cites this paper as [1]
The cited source says what the claim attributes to it.
In the citing paper
“The most common practice employs four-point resistance measurements [11][12][13][14][28][29][30][31][32][33][34][35], while in some cases (typically thin sheets) an eddy current resistivity measurement technique is used [18,36].”
From Electrical and thermal stability of Al-Cu welds: Performance benchmarking of the hybrid metal extrusion and bonding process (2022) · cites this paper as [18]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Still being checked.
Research works printed but not linked: 36
- Wang, 2019, Effect of heat treatment on bonding mechanism and mechanical properties of high strength Cu/Al/Cu clad composite, J. Alloys Compd., 801, 573, 10.1016/j.jallcom.2019.06.132 · DOI · Paper page
- Li, 2018, Interfacial bonding mechanism and annealing effect on Cu–Al joint produced by solid-liquid compound casting, J. Mater. Process. Technol., 252, 795, 10.1016/j.jmatprotec.2017.10.050 · DOI · Paper page
- Wei, 2019, The Interfacial characterization and performance of Cu/Al-conductive heads processed by explosion welding, cold pressure welding, and solid-liquid casting, Metals, 9, 237, 10.3390/met9020237 · DOI
- Sheng, 2011, Influence of heat treatment on interface of Cu/Al bimetal composite fabricated by cold rolling, Compos. B. Eng., 42, 1468, 10.1016/j.compositesb.2011.04.045 · DOI · Paper page
- Kim, 2014, Mechanochemical joining in cold roll-cladding of tri-layered Cu/Al/Cu composite and the interface cracking behavior, Mater. Des., 57, 625, 10.1016/j.matdes.2014.01.054 · DOI
- Kim, 2013, Effect of heat treatment on the bending behavior of tri-layered Cu/Al/Cu composite plates, Mater. Des., 47, 590, 10.1016/j.matdes.2012.12.070 · DOI · Paper page
- Abbasi, 2001, Growth rate of intermetallic compounds in Al/Cu bimetal produced by cold roll welding process, J. Alloys Compd., 319, 233, 10.1016/S0925-8388(01)00872-6 · DOI · Paper page
- Kim, 2019, Effect of intermetallic compound layer on peel strength and crack propagation behavior in Cu/Al/Cu clad composites, Metals, 9, 1155, 10.3390/met9111155 · DOI
- Athar, 2015, Weldability window and the effect of interface morphology on the properties of Al/Cu/Al laminated composites fabricated by explosive welding, Mater. Des., 86, 516, 10.1016/j.matdes.2015.07.114 · DOI
- Shiran, 2018, Multilayer Cu/Al/Cu explosive welded joints: characterizing heat treatment effect on the interface microstructure and mechanical properties, J. Manuf. Process., 35, 657, 10.1016/j.jmapro.2018.09.014 · DOI
- Chen, 2013, Atomic diffusion behavior in Cu-Al explosive welding process, J. Appl. Phys., 113, 10.1063/1.4775788 · DOI
- Kaya, 2018, Investigation of copper-aluminium composite materials produced by explosive welding, Metals, 8, 780, 10.3390/met8100780 · DOI
- Honarpisheh, 2012, Investigation of annealing treatment on the interfacial properties of explosive-welded Al/Cu/Al multilayer, Mater. Des., 37, 122, 10.1016/j.matdes.2011.12.045 · DOI
- Chang, 2018, Study on interface structure of Cu/Al clad plates by roll casting, Metals, 8, 770, 10.3390/met8100770 · DOI
- Huang, 2017, Evolution of bonding interface in solid-liquid cast-rolling bonding of Cu/Al clad strip, Trans. Nonferrous Met. Soc. China, 27, 1019, 10.1016/S1003-6326(17)60119-5 · DOI · Paper page
- Liu, 2019, Study on interface microstructures of Cu–Al composite plate fabricated by cast rolling, J. Mater. Eng. Perform., 28, 7241, 10.1007/s11665-019-04451-y · DOI
- Tian, 2018, Numerical simulations of the Cu/Al composite plate continuous cast-rolling process, Mater. Res. Express, 5, 10.1088/2053-1591/aadfbe · DOI
- Liu, 2019, Effect of annealing temperature on microstructure and bond strength of cast-rolling Cu–Al clad plates, Mater. Res. Express, 6, 10.1088/2053-1591/ab1d3a · DOI
- Rhee, 2004, Fabrication of aluminum/copper clad composite using hot hydrostatic extrusion process and its material characteristics, Mater. Sci. Eng. A, 384, 70, 10.1016/j.msea.2004.05.051 · DOI · Paper page
- Lee, 2015, Mechanical and asymmetrical thermal properties of Al/Cu composite fabricated by repeated hydrostatic extrusion process, Met. Mater. Int., 21, 402, 10.1007/s12540-015-4242-z · DOI
- Guo, 2010, Microstructure and tensile behavior of Cu–Al multi-layered composites prepared by plasma activated sintering, Mater. Sci. Eng. A, 527, 5234, 10.1016/j.msea.2010.04.080 · DOI
- Kim, 2016, Interactive deformation and enhanced ductility of tri-layered Cu/Al/Cu clad composite, Mater. Sci. Eng. A, 651, 976, 10.1016/j.msea.2015.11.062 · DOI
- Chen, 2019, Coupling effects of matrix and interface on synergetic deformation behaviors of Cu/Al composite plates, Mater. Res. Express, 6, 1265a3, 10.1088/2053-1591/ab5c2f · DOI
- Mao, 2018, Interfacial characterization and bonding properties of copper/aluminum clad sheets processed by horizontal twin-roll casting, multi-pass rolling, and annealing, Metals, 8, 645, 10.3390/met8080645 · DOI
- Hoseini-Athar, 2016, Interface morphology and mechanical properties of Al–Cu–Al laminated composites fabricated by explosive welding and subsequent rolling process, Met. Mater. Int., 22, 670, 10.1007/s12540-016-5687-4 · DOI
- Asemabadi, 2012, Investigation of cold rolling influence on the mechanical properties of explosive-welded Al/Cu bimetal, Mater. Sci. Eng. A, 558, 144, 10.1016/j.msea.2012.07.102 · DOI
- Bataev, 2012, Structural and mechanical properties of metallic-intermetallic laminate composites produced by explosive welding and annealing, Mater. Des., 35, 225, 10.1016/j.matdes.2011.09.030 · DOI
- Gueydan, 2014, Study of the intermetallic growth in copper-clad aluminum wires after thermal aging, Intermetallics, 50, 34, 10.1016/j.intermet.2014.02.007 · DOI · Paper page
- Liu, 2019, Cu–Al interfacial formation and kinetic growth behavior during HTS reliability test, J. Mater. Process. Technol., 267, 90, 10.1016/j.jmatprotec.2018.12.012 · DOI · Paper page
- Ma, 2019, Growth characterization of intermetallic compounds at the Cu/Al solid state interface, Mater. Res. Express, 6, 10.1088/2053-1591/ab3171 · DOI
- Chen, 2007, Effect of annealing on the interfacial structure of aluminum-copper joints., Mater. Trans., 48, 1938, 10.2320/matertrans.MER2006371 · DOI
- Lee, 2005, Effects of intermetallic compound on the electrical and mechanical properties of friction welded Cu/Al bimetallic joints during annealing, J. Alloy. Compd., 390, 212, 10.1016/j.jallcom.2004.07.057 · DOI · Paper page
- Braunovic, 1994, Intermetallic compounds at aluminum-to-copper electrical interfaces: effect of temperature and electric current, IEEE Trans. Compon. Pack. Manuf. Technol., 17, 78, 10.1109/95.296372 · DOI · Paper page
- Wu, 2015, Heterogeneous lamella structure unites ultrafine-grain strength with coarse-grain ductility, Proc. Natl Acad. Sci. USA, 112, 14501, 10.1073/pnas.1517193112 · DOI
- Zhang, 2019, Comparisons of the microstructures and micro-mechanical properties of copper/steel explosive-bonded wave interfaces, Mater. Sci. Eng. A, 756, 430, 10.1016/j.msea.2019.04.064 · DOI
- Braunovic, 1992, Intermetallic compounds at aluminum-to-copper and copper-to-tin electrical interfaces., IEEE Electrical Contacts, 10, 1109
Cited by
Sorted by citations
Elkjaer, A., Sørhaug, J. A., Ringen, G., Bjørge, R., & Grong, Ø. (2022) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2022.04.029 · Cited by 23
Nolte, N., Lukasczyk, T., & Mayer, B. (2022) · Metals · doi:10.3390/met12081314 · Cited by 5
“[1] showed this relationship in their investigations by means of annealing experiments.”
Method
Metadata
- Authors
- Li, H., Yang, Y., Liang, X., Zhang, W., Cao, L., Wu, C., Zeng, Z., & Wang, L.
- Affiliations
- Central South University (CN)
- Corresponding author
- Li, Huizhong
- Liang, Xiaopeng
- Wang, Li
- Venue
- Materials Research Express
- Publisher
- IOP Publishing
- Published
- 2020-10-01
- Volume
- 7
- Issue
- 10
- Pages
- 106502
- ISSN
- 2053-1591 (ISSN-L)
- OpenAlex
- W3088381361
- Cited by
- 26
- References
- 0
- Citations by year
- 2026: 4 · 2025: 7 · 2024: 6 · 2023: 3 · 2022: 4 · 2021: 2
- FWCI
- 1.11
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Materials Research Express (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Funders
- Fundamental Research Fund for the Central Universities of Central South University (502041002)
- National key research and development plan of China (2016YFB0700302)
- National Natural Science Foundation of China (51771232)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced Welding Techniques Analysis
- Physical Sciences › Materials Science › Metals and Alloys › Microstructure and mechanical properties
- Physical Sciences › Materials Science › Metals and Alloys › Metallurgy and Material Science
- Keywords
- explosive welding, cold rolling, annealing temperature, annealing time, AlCu, Al4Cu9, activation energy, tensile strength, yield strength, fracture elongation, lap shear strength, electrical conductivity, microstructure
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
