A Review of Integrated On-Board EV Battery Chargers: Advanced Topologies, Recent Developments and Optimal Selection of FSCW Slot/Pole Combination
Open accessThe DOI matches its Crossref record; 109 of the 111 references it cites were found in a registry or an index.
Abstract
Integrated on-board battery chargers (OBCs) have been recently introduced as an optimal/elegant solution to increase electric vehicle (EV) market penetration as well as minimize overall EV cost. Unlike conventional off-board and on-board battery chargers, integrated OBCs exploit the existing propulsion equipment for battery charging without extra bulky components and/or dedicated infrastructure. OBCs are broadly categorized into three-phase and single-phase types with unidirectional or bidirectional power flow. This paper starts with surveying the main topologies introduced in the recent literature employing either induction or permanent magnet motors to realize fully integrated slow (single-phase) and fast (three-phase) on-board EV battery charging systems, with emphasis on topologies that entail no or minimum hardware reconfiguration. Although, permanent magnet (PM) motors with conventional double-layer distributed winding layouts have been deployed in most commercial EV motors, the non-overlapped fractional slot concentrated winding (FSCW) has been the prevailing choice in the most recent permanent magnet motor designs due to its outstanding operational merits. Hence, a thorough investigation of the impact different FSCW stator winding designs have on machine performance under the charging process is presented in this paper. To this end, the induced magnet losses, which represent a challenging demerit of the FSCW, have been used to compare different topologies under both propulsion and charging operation modes. Based on the introduced comparative study, the optimal slot/pole combinations that correspond to the best compromise under both operational modes have been highlighted.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures






































Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“For instance, the dual-use of motor windings in the charging process, as seen in Integrated Charger Inverter (ICI) systems, eliminates the need for separate inductors, reducing weight and improving efficiency [19,118].”
From On-Board Chargers for Electric Vehicles: A Comprehensive Performance and Efficiency Review (2024) · cites this paper as [19]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Yilmaz, M., & Krein, P. T. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2212917 · Cited by 3,118 · cited 4×
“tional or bidirectional power flow capability [5].”
BackgroundInfluentialMultiphase Electric Machines for Variable-Speed Applications
Levi, E. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.918488 · Cited by 2,157 · cited 1×
“The converter rating per phase is reduced by splitting the power among more phases, while offering improved fault tolerance [19].”
BackgroundMultiphase induction motor drives – a technology status review
Levi, E., Bojoi, R., Profumo, F., Toliyat, H. A., & Williamson, S. (2007) · IET Electric Power Applications · doi:10.1049/iet-epa:20060342 · Cited by 1,619 · cited 1×
“Additionally, the decoupling transformations utilized in multiphase systems are quite sophisticated when compared to their three-phase counterparts [21].”
BackgroundSwitched Reluctance Motors and Their Control
Miller, T. J. E. (1993) · Medical Entomology and Zoology · Cited by 1,583
EL-Refaie, A. M. (2010) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2009.2030211 · Cited by 1,373 · cited 1×
“The FSCWhelps reduce end turn length, simplifies manufacturing and enables a slot fill factor approximately equal to 78%, especially when coupled with segmented stator structures [24].”
BackgroundDannehl, J., Wessels, C., & Fuchs, F. W. (2009) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.2008774 · Cited by 747 · cited 1×
“Under the voltage-oriented control method [79], the battery is charged with a constant maximum current until reaching the cut-off voltage, which is a predefined threshold value known as a safety limit at which constant voltage (CV) control begins.”
MethodElectrical Motor Drivelines in Commercial All-Electric Vehicles: A Review
de Santiago, J., Bernhoff, H., Ekergård, B., Eriksson, S., Ferhatovic, S., Waters, R., & Leijon, M. (2012) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2011.2177873 · Cited by 669 · cited 10×
“These two intelligent modules form the SRM electrical drive using five inverter legs.”
BackgroundInfluentialSynthesis of high performance PM motors with concentrated windings
Cros, J., & Viarouge, P. (2002) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2002.1009476 · Cited by 667
Global Trends in High-Power On-Board Chargers for Electric Vehicles
Khaligh, A., & D'Antonio, M. (2019) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2019.2897050 · Cited by 652 · cited 2×
“patible with smart grid functionalities [110].”
BackgroundKhaligh, A., & Dusmez, S. (2012) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2012.2213104 · Cited by 630 · cited 2×
“Considering that most commercial EVs are based on three-phase motors, various integrated chargers employing three-phase machines have been introduced in the literature [4], [36].”
Background
Research works printed but not linked: 3
- IEA, ''Global EV outlook 2019: Scaling-up the transition to electric mobility,'' OECD, Paris, France, 2019.
- AYMAN S. ABDEL-KHALIK (Senior Member, IEEE) received the B.Sc. and M.Sc. degrees in electrical engineering from Alexandria University, Alexandria, Egypt, in 2001 and 2004, respectively, and the Ph.D. degree in electrical engineering from Alexandria University and Strathclyde University, Glasgow, U.K., in 2009, under a Dual Channel Program. He is currently a Professor with the Department of Electrical Engineering, Faculty of Engineering, Alexandria University. His current research interests include electrical machine design and modeling, electric drives, energy conversion, and renewable energy. He serves as an Associate Editor for the IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS and the IET Electric Power Applications Journal. He also serves as the Executive Editor of the Alexandria Engineering Journal.
- RAGI A. HAMDY (Senior Member, IEEE) received the B.Sc. and M.Sc. degrees from Alexan- dria University, Alexandria, Egypt, in 1991 and 1994, respectively, and the Ph.D. degree from Heriot-Watt University, U.K., in 1999. He is currently a Professor with the Department of Electrical Engineering, Faculty of Engineering, Alexandria University. His current research inter- ests include electric machines, electric drives, and power electronics.
Cited by
Items 101–200 of 261
Yang, S., Li, S., Wang, T., Liang, F., & Su, X. (2020) · International Conference on HVDC (HVDC) · doi:10.1109/hvdc50696.2020.9292707 · Cited by 6
Karlsson, A., & Alaküla, M. (2021) · World Electric Vehicle Journal · doi:10.3390/wevj12040241 · Cited by 6
A fast charging of Li‐ion battery based on Lyapunov function for electrical vehicle
Vazini, H., Asadi, M., Karimadini, M., & Hajisadeghian, H. (2021) · IET Power Electronics · doi:10.1049/pel2.12209 · Cited by 6
Three-Level Reduced Switch AC/DC/AC Power Conversion System for High Voltage Electric Vehicles
Sadeghi, Z., Shahparasti, M., Rajaei, A., & Laaksonen, H. J. J. (2022) · Sustainability · doi:10.3390/su14031620 · Cited by 6
“Various DC-DC converter topologies such as buck-boost, Z-source, and resonant converters are proposed for EVs chargers in [24,25].”
BackgroundReduction of Harmonics on Source Side Using Filters for EV Charging Applications
Sabarimuthu, M., Kumar, M. A., Vennila, R., Juhair, P. M., Johitha, B., & Piranav, M. (2022) · International Conference for Emerging Technology (INCET) · doi:10.1109/incet54531.2022.9824143 · Cited by 6
A Review of Three Phase AC-DC Power Factor Correction Converters for Electric Vehicle Fast Charging
Mollahasanoğlu, M., & Okumuş, H. İ. (2022) · European Journal of Science and Technology · doi:10.31590/ejosat.1041081 · Cited by 6
“On-board chargers are slow because they operate at lower currents (Metwly et al., 2020; Sam et al., 2021; Yuan et al., 2021).”
BackgroundComparison of High-Energy Density and High-Power Density Batteries for an Electric Vehicle
Fadili, S., German, R., Bouscayrol, A., Mayet, C., Fiani, P., & Noirtat, E. (2025) · IEEE Open Journal of Vehicular Technology · doi:10.1109/ojvt.2025.3583070 · Cited by 5
“It is assumed that, from the DC bus, the slow charger has the same mean-value behavior as the fast charger [38], only the charging power and losses differ.”
A Review of Emerging Trends of GaN Power Semiconductor Applications in Onboard Chargers
Razali, M. R., Jamaludin, J., Bakar, A. S. A., Ismail, F., Za’im, R., & Krismadinata, K. (2025) · Journal of Circuits Systems and Computers · doi:10.1142/s0218126626300023 · Cited by 5
New combined control strategy of on-board bidirectional battery chargers for electric vehicles
Hadji, K., Hartani, K., & Chikouche, T. M. (2023) · International Journal of Power Electronics and Drive Systems/International Journal of Electrical and Computer Engineering · doi:10.11591/ijpeds.v15.i1.pp303-311 · Cited by 5
“Several of the AC/DC boost topologies mentioned in [13] have been compared based on these criteria: The size of the boosting inductors, the active power switches as well as the output voltage level [14]–[16].”
BackgroundAbdel-Wahed, A. T., Abdel-Khalik, A. S., Hamad, M. S., Massoud, A. M., & Ahmed, S. (2024) · International Conference on Smart Grid and Renewable Energy (SGRE) · doi:10.1109/sgre59715.2024.10428879 · Cited by 5
“[2] summarizes the various topologies of the IOBCs.”
BackgroundSelf-citationDC Link Voltage Optimization for Efficiency Enhancement of Electric Vehicle Onboard Chargers
Kazemtarghi, A., Ishraq, N., Rathod, P., Mallik, A., & Johnson, N. G. (2023) · IEEE Industrial Electronics Society Annual On-Line Conference (ONCON) · doi:10.1109/oncon60463.2023.10431027 · Cited by 5
Intelligent Charging system for Electric Vehicle Batteries
Ramesh, P., Gouda, P. K., Sandhya, S., Dhanush, C. N., Pavithra, Y., & Simran, S. (2024) · International Conference on Electronics, Computing, Communication and Control Technology (ICECCC) · doi:10.1109/iceccc61767.2024.10593895 · Cited by 5
Model Predictive Control for Modular Electric Vehicle Charger
Farooqi, M. Z., Singh, B., & Panigrahi, B. K. (2020) · IEEE International Conference on Power Electronics, Drives and Energy Systems · doi:10.1109/pedes49360.2020.9379649 · Cited by 5
“To avoid these bulky transformer, an EV charging structure is discussed in this work comprising cascaded H-bridges and bi-directional isolated DC/DC converters (DHB’s) which are incorporated with high-frequency transformers[7].”
MethodHota, A., & Agarwal, V. (2022) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2022.3190460 · Cited by 5
Improved Power Quality of Single Phase On-Board Charger with Wide Voltage Conversion Range
Vinusha, B., Kalpana, R., & Kishan, D. (2023) · IEEE IAS Global Conference on Renewable Energy and Hydrogen Technologies (GlobConHT) · doi:10.1109/globconht56829.2023.10087583 · Cited by 5
“Addressing rated power and topologies, there is a considerable amount of literature available as shown in [1],[2].”
BackgroundMagnetically Coupled Interleaved Buck Integrated On-Board Charger for Light Electric Vehicles
Afriyie, D., Khan, A. A., & Iqbal, M. T. (2025) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2025.3581482 · Cited by 4
“Unlike the level I and II chargers, level III has the highest power rating above 50 kW and handles voltages of 208–600 V, with the least charging time ranging from 0.2 to 0.5 h [9], [10].”
InfluentialDwivedi, R., Singh, S., & Singh, B. (2022) · International Journal of Ambient Energy · doi:10.1080/01430750.2022.2122558 · Cited by 4
Lei, Y., Du, G., Li, T., & Yang, Z. (2022) · International Journal of Circuit Theory and Applications · doi:10.1002/cta.3475 · Cited by 4
“To achieve fast charging, the three-phase (3p) supply is required because the current limitation of the single-phase outlet is low.(3) Nevertheless, symmetrical 3p currents may generate a rotating magnetic field in the machine so that the vehicle will move and cannot be charged in a stationary location.”
BackgroundCittanti, D., Vico, E., Mandrile, F., Armando, E. G., & Bojoi, R. I. (2022) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce50734.2022.9947444 · Cited by 4
“, inverter and motor) to provide the charging function is currently an active research topic [1], [2].”
BackgroundIntegrated on-board electric vehicle battery charger with multifunctional features
Gupta, J., Maurya, R., & Arya, S. R. (2024) · Australian Journal of Electrical & Electronics Engineering · doi:10.1080/1448837x.2024.2350838 · Cited by 4
Joy, A. V., Kangappadan, E. T., Prasad, A., Nandakishore, K. S., & Ismail, T. (2024) · International Conference on Advancement in Renewable Energy and Intelligent Systems (AREIS) · doi:10.1109/areis62559.2024.10893645 · Cited by 4
An Integrated Onboard EV Charger With Wide Voltage Range Compatibility
Kumar, V., Prabhakaran, P., Reddy, B. D., & Daya, J. L. F. (2025) · IEEE Access · doi:10.1109/access.2025.3590958 · Cited by 4
“These specialized power converters are commonly referred to as integrated onboard chargers (IOCs) in the literature, with relevant works found in [3], [4], [5], [6], [7], [8], [9], [10], [11], [12], [13], [14], [15], [16], [17], [18], [19], [20], and [21].”
Fractional-Slot PMSMs With One Coil Parallel Branches Made Phases—Part I: Investigation Study
Masmoudi, A., Mkaouar, S., Maaoui, A., & Schier, M. (2021) · IEEE Access · doi:10.1109/access.2021.3113712 · Cited by 4
“INTRODUCTION Much attention is currently given to FSPMSMs to equip a variety of applications covering a wide range of power, from medical actuators and household appliances till wind turbines, going through electric and hybrid vehicles [1]–[5].”
BackgroundLee, Y.-L., Lin, C., Lu, S., & Liu, H. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.105024 · Cited by 4
Dynamic Characteristic Improvement of Integrated On-Board Charger Using a Model Predictive Control
Bak, Y. (2022) · Energies · doi:10.3390/en15228745 · Cited by 4
Design of Unequal Width Stator Teeth Permanent Magnet Motor Based on Actual Winding Factor
Zhu, J., & Chen, Z. (2023) · International Conference on Electrical Machines and Systems (ICEMS) · doi:10.1109/icems59686.2023.10345195 · Cited by 4
“The fractional-slot concentrated winding Permanent Synchronous Machines(FSCWPMSM) are widely used as traction motors in new energy vehicles [1], [2].”
BackgroundThermal simulation of a 7kW interleaved module for fast automotive charger
Anoldo, L., Piccione, G. G., Mauromicale, G., Sitta, A., Fazio, E., Calabretta, M., Lionetto, A., Messina, A. A., Guardo, M. D., & Patanè, S. (2021) · IEEE International Conference on Environment and Electrical Engineering and IEEE Industrial and Commercial Power Systems Europe (EEEIC / I&CPS Europe) · doi:10.1109/eeeic/icpseurope51590.2021.9584683 · Cited by 4
Common-Mode Current Prediction in a Non-isolated Onboard EV Fast Charger
Nazeri, A., Perera, C., & Lehn, P. W. (2024) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec48139.2024.10509239 · Cited by 3
A Multi-Functional Integrated Onboard Charger for Dual-Motor Driving EVs
Tong, M., Liu, X., Chen, Y., Sun, L., & Xu, Z. (2024) · Energies · doi:10.3390/en17215276 · Cited by 3
Diagnostics of Supraharmonics in Terms of Analysis of Electric Vehicle Charging
Jędryczka, C., Kuwałek, P., & Wiczyński, G. (2024) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2024.3520071 · Cited by 3
“To generalize, in individual cases the battery pack charging process is performed in the constant current (CC) or constant voltage (CV) mode [41], [42], [43].”
Funatsu, S., Matsumori, H., Kosaka, T., Matsui, N., Nakamura, K., Takahashi, M., Taguchi, S., & Saha, S. (2025) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2025.3600210 · Cited by 3
“1 and 2 respectively [7], [8], [9], [10], [11], [12], [13].”
Chikondra, B., Kumar, P., Arzani, A., & Beig, A. R. (2025) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2025.3634353 · Cited by 3
“increased torque density, reduced torque ripple, reduced dc-link capacitor volume, improved compatibility with bearingless motors and integrated battery chargers, improved fault tolerance, and reduced current rating per phase [1], [2].”
Integrated On-Board Charger, Wireless Charging and Auxiliary Power Topologies for EVs: A Survey
Singh, D. C. D. R., Narayanamoorthi, R., Aldahmashi, J., & Yousef, A. H. (2026) · Energies · doi:10.3390/en19030689 · Cited by 3
Space Vector-Based Hysteresis Current Controller of Asymmetrical Six-Phase Induction Motor
Mamdouh, M., & Abido, M. A. (2024) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2024.3443952 · Cited by 3
Multibattery Charger System Based on a Multilevel Dual-Active-Bridge Power Converter
Campos-Salazar, J. M., Busquets‐Monge, S., Filbà-Martínez, À., & Alepuz, S. (2025) · Electronics · doi:10.3390/electronics14081659 · Cited by 3
Metwly, M. Y., & He, J. (2023) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce53617.2023.10362693 · Cited by 3
Self-citationNakkeeran, R., & Bharatiraja, C. (2024) · IEEE International Conference on Sustainable Energy and Future Electric Transportation (SEFET) · doi:10.1109/sefet61574.2024.10718173 · Cited by 3
“On-board chargers (OBCs) play a critical role in improving the usability and versatility of EVs[2].”
BackgroundA Parameter Design Method of CLLC Resonant Converter Based On Time-Domain Model
Ge, J., & Ma, H. (2020) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon43393.2020.9254722 · Cited by 3
“1, CLLC resonant converters become the preferred option of portable DC / DC part in OBC for their high power density, high efficiency and bidirectional transmission [1]-[8].”
BackgroundÇetin, E., & Mustafa, Y. A. Z. (2021) · International Journal of Automotive Science And Technology · doi:10.30939/ijastech..984760 · Cited by 3
Performance Comparison of Six-Phase PM Machine with Several Winding Layouts for EV Applications
Abdel-Wahed, A. T., Metwly, M. Y., Hemeida, A., Abdel-Khalik, A. S., Hamad, M. S., & Ahmed, S. (2023) · IEEE Conference on Power Electronics and Renewable Energy (CPERE) · doi:10.1109/cpere56564.2023.10119595 · Cited by 3
“Various slot/pole combinations have shown promise in EV applications [3].”
BackgroundInfluentialSelf-citationActive Power Decoupling Strategy for Single Phase AC Charging Using a Dual Inverter Drive
Perera, C., Pathmanathan, M., Viana, C. C. D., & Lehn, P. W. (2023) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec43580.2023.10131375 · Cited by 3
“The two main challenges [11] of integrated OBCs though, are the reconfiguration of components between driving and charging modes, and the suppression of torque production during charging.”
BackgroundA Novel 1-ϕ Cuk Based On-Board EV Charger with Minimal Power Components
Chamarthi, P. K., Edrington, C. S., Arsalan, A., Timilsina, L., Papari, B., Özkan, G., & Moghassemi, A. (2023) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2023-01-1686 · Cited by 3
Mollahasanoğlu, M., Mollahasanoğlu, H., & Okumuş, H. İ. (2024) · Pamukkale University Journal of Engineering Sciences · doi:10.5505/pajes.2023.89195 · Cited by 2
Du, J., Zhong, R., Wu, Z., Hua, W., Wu, Z. F., Zhang, C., & Hu, Y. (2025) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2025.3591428 · Cited by 2
“A typical 22-pole 24-slot DTP ER SPM machine is selected to illustrate the influence of inherent spatial-coupled modal shapes since it can be designed for more winding configurations, including SL and DL [18], [19], [23].”
Dam, D., & Basak, S. (2025) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2025.3590310 · Cited by 2
“Investigations on the slot/pole combinations of inner-rotor six-phase/nine-phase interior permanent magnet machine (which is used for three-phase charging applications) are conducted in [4], [5], [6].”
Deb, S., & Pramanick, S. K. (2025) · Sadhana · doi:10.1007/s12046-025-02774-2 · Cited by 2
“The long charging duration becomes a notable hurdle for low-power OBCs [12].”
Current and Voltage Sensing Methods of BCBB Converter Used in Battery Interfacing System
Li, P., Nisar, H., & Bazzi, A. M. (2025) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2025.3603530 · Cited by 2
“In fact, with the assistance of the solid-state transformer, DAB is an outstanding topology that has been widely used in the industry [6], especially onboard battery chargers in electric vehicles [7].”
Savio, F. M., Dharmalingam, K., & Kamal, C. (2025) · Journal of Electrical Engineering and Technology · doi:10.1007/s42835-025-02476-z · Cited by 2
“The cirtical review on battery state of charge is done in paper [ 7, 8 ].”
Afriyie, D., Brakoh, G., Khan, A. A., & Iqbal, M. T. (2025) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2025.3635526 · Cited by 2
“This is achieved by using the motor in the EV propulsion systems to aid in charging the battery [12].”
Thomas, J., Venkadesan, A., Vishvanath, M., & Sedhuraman, K. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.119881 · Cited by 2
Ntombela, M. (2026) · World Electric Vehicle Journal · doi:10.3390/wevj17080393 · Cited by 2
Research on motor driving and vehicle charging integrated system
Zhou, K., Che, Y., & Fang, H. (2024) · Electrical Engineering · doi:10.1007/s00202-024-02298-8 · Cited by 2
Kan, R. F. V., Ramos, L. A., Mezaroba, M., & Rech, C. (2024) · Eletrônica de Potência · doi:10.18618/rep.2024.1.0030 · Cited by 3
A New Integrated Onboard Battery Charger For Electric Scooters
Huang, P.-H., Rana, N., Gupta, A., Enjeti, P. N., & Basu, K. (2024) · International Telecommunications Energy Conference (INTELEC) · doi:10.1109/intelec60315.2024.10678977 · Cited by 2
“To address the aforementioned challenges, a crucial element, the integrated onboard battery chargers (IOBCs) is introduced to greatly improve the usability, convenience, and overall cost of light-weight EVs [1].”
BackgroundTorque and Current Ripple Analysis in Integrated DC-DC Boost Chargers Based on SynRMs and WR-SMs
Rizzoli, G., Vancini, L., Mengoni, M., Sala, G., Zarri, L., & Tani, A. (2024) · International Conference on Electrical Machines (ICEM) · doi:10.1109/icem60801.2024.10700311 · Cited by 2
Single Stage Isolated Power Conditioning Unit for Plugin Electric Vehicles on-Board Charger
Ali, M. A., Singh, N. P., Raveendhra, D., Pendem, S. R., Raju, B. N., & Bobba, P. B. (2024) · IEEE International Conference on Sustainable Energy and Future Electric Transportation (SEFET) · doi:10.1109/sefet61574.2024.10718263 · Cited by 2
“[4].”
SuperBox: A 4-in-1 Power Electronics Solution for Dual-Motor Electric Vehicles
Taha, W., Wang, Y., Anand, A., & Mohammadi, H. (2025) · IEEE Transportation Electrification Conference and Expo · doi:10.1109/itec63604.2025.11097934 · Cited by 2
“Similar multiphase motor-based iOBCs approaches, with extension to nine-phase machines for three-phase AC charging, are discussed in [5] and [11].”
Design and Simulation of a Rectifier for Bidirectional Electric Vehicle Chargers
Bajwa, O. J., & Zhang, S. (2021) · IEEE Student Conference on Electric Machines and Systems (SCEMS) · doi:10.1109/scems52239.2021.9646170 · Cited by 2
Electrical Vehicle Charging Station Mathematical Modeling and Stability Analysis
Verma, S., Chatterjee, K., & Sandhya, K. (2022) · International Conference on Advances in Electrical, Computing, Communication and Sustainable Technologies (ICAECT) · doi:10.1109/icaect54875.2022.9807841 · Cited by 2
“EVs have rechargeable batteries, broadly classified as Lead Acid batteries, Nickel-Based Batteries, and Lithium Based Battery [13].”
BackgroundA Novel High Power Three Phase Integrated Battery Charger for Plug-in Electric Vehicles
Mutyam, L., & Agarwal, V. (2022) · IEEE International Conference on Power Electronics, Drives and Energy Systems · doi:10.1109/pedes56012.2022.10080755 · Cited by 2
“978-1-6654-5566-4/22/$31.00 ©2022 IEEE Keywords— Integrated onboard chargers (IBC), Electric vehicles (EVs), Permanent magnet synchronous motors (PMSM) I. INTRODUCTION Widespread adaption of plug-in electric vehicles (PEVs) is limited by cost, size, range anxiety, longer battery charging time, and charging convenience…”
BackgroundInfluentialCai, H., Kong, D., Sun, H., Wang, Q., & Liu, H. (2024) · Sustainable Energy Technologies and Assessments · doi:10.1016/j.seta.2024.103933 · Cited by 2
A Study of Three-Phase Integrated Battery Charger Based on Six-Phase Open-Winding Machine
Cheng, J., Ouyang, X., Raherimihaja, H. J., & He, B. (2025) · International Conference on Information Science, Electrical and Automation Engineering (ISEAE) · doi:10.1109/iseae64934.2025.11041864 · Cited by 2
A Laboratory for Testing E-mobility Power Electronics
Cipolletta, G., D’Avanzo, G., Femine, A. D., Gallo, D., Landi, C., & Luiso, M. (2021) · IEEE International Workshop on Metrology for Automotive (MetroAutomotive) · doi:10.1109/metroautomotive50197.2021.9502852 · Cited by 2
Investigation of An Integrated Battery Charger for EVs based on A Dual-Motor Traction System
Tong, M., Liu, X., Sun, L., Xu, Z., Cheng, M., & Zou, Q. (2022) · IEEE Transportation Electrification Conference and Expo, Asia-Pacific (ITEC Asia-Pacific) · doi:10.1109/itecasia-pacific56316.2022.9942110 · Cited by 2
“1, a new type of integrated motor-driving and on-board battery-charging system has been becoming more and more popular, in which the motor windings and the inverters of the traction system are re-used in different operation modes, and the state-of-the-art technologies of this aspect are given in several review papers…”
BackgroundModified Zeta Based PV System For EV Battery Charging
Kar, S., Lins, A. W., Kavin, K. S., Patwa, S., Martin, G. W., & Karthikeyan, D. (2023) · International Conference on Energy, Materials and Communication Engineering (ICEMCE) · doi:10.1109/icemce57940.2023.10434022 · Cited by 1
“Four charge-discharge cycles, using the manufacturer's suggested charging profile and a discharge rate of C/3 (based on the manufacturer's original rating), will establish the module's capacity [7].”
MethodWu, P., Xu, J., Wang, K., Li, Z., Li, G., & Wang, H. (2023) · Asia Power and Electrical Technology Conference (APET) · doi:10.1109/apet59977.2023.10489330 · Cited by 1
“The typical applications include the dual active bridge [3] (DAB) circuit as core of the energy router and the on-board charger [4] (OBC) circuit used in the electric vehicle, whose switching frequency can be as high as 50~200kHz.”
BackgroundComparison of Current Control Techniques for Single-Phase Integrated On-Board Chargers
Dam, D., & Basak, S. (2024) · International Telecommunications Energy Conference (INTELEC) · doi:10.1109/intelec60315.2024.10678955 · Cited by 1
“1: Circuit diagram of the system in propulsion mode are required [8].”
BackgroundEvaluation of an Intelligent Controller for Electric Vehicle Charging with Vienna Rectifier Topology
Lingadahalli, A., Tashakor, N., Wiehoff, H.-J., Wang, H., & Goetz, S. M. (2024) · IEEE International Conference on Power Electronics, Drives and Energy Systems · doi:10.1109/pedes61459.2024.10961302 · Cited by 1
“Among various charging methods for EVs, onboard charging is very popular at home, at office buildings, and shops due to convenience, low maintenance, and the independence of drivers from the availability of DC charging infrastructure at their destination [10], [12], [14], [15].”
Taha, W. A., Abouelseoud, Y., Abdel-Khalik, A. S., & Kamel, S. H. (2025) · Alexandria Engineering Journal · doi:10.1016/j.aej.2025.07.031 · Cited by 1
Self-citationA Novel Unified Converter for Onboard Charging and Traction Application for EVs
Mukherjee, S., & Das, M. (2025) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon58223.2025.11221773 · Cited by 1
“…onboard chargers (OBCs) utilize propulsion components for battery charging, with recent research on fractional slot concentrated winding (FSCW)-based permanent magnet (PM) motor drives [15] and switched reluctance motor (SRM) drives [16] enabling dual mode operation without additional hardware.”
Rana, N., Ushida, K., Nakamura, K., Hotta, Y., Saha, S., & Basu, K. (2025) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce58356.2025.11260105 · Cited by 1
“In the literature [1]–[5], the traction inverter and motor winding are modified to create a non-isolated single port IOBC, as shown in Fig.”
Multiport Buck-Boost Integrated On-Board EV Charger for Multi-Energy Powertrains
Gohari, H. S., Safaeinasab, A., Abbaszadeh, K., Sergeant, P., & Vansompel, H. (2026) · IEEE Access · doi:10.1109/access.2026.3672173 · Cited by 1
“This boosts demand for compact, efficient powertrains, driving interest in integrated charg-ers that reuse motor stator coils as PFC inductors [7].”
Brakoh, G., Khan, A. A., & Ahmed, H. F. (2026) · IEEE Journal of Emerging and Selected Topics in Industrial Electronics · doi:10.1109/jestie.2026.3680446 · Cited by 1
Loss Characterization of Additively Manufactured Windings for Aerospace Propulsion Motors
Tesfamikael, H. H., Darmani, M. A., Murataliyev, M., Hague, R., Gerada, C., & Degano, M. (2026) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2026.3683253 · Cited by 1
“In general, the rotor index decreases with an increasing slot / pole combination, and its value di ff ers between generating and motoring modes, as discussed in [44].”
A Single-Phase Integrated Onboard Charger for Plug-In Dual-Motor EVs
Brakoh, G., Khan, A. A., Quaicoe, J. E., & Ahmed, H. F. (2026) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2026.3688075 · Cited by 1
“The motor type, number of phases, and the specific power converter used are all factors that influence the viability of integrated OBCs [7].”
Harmonic Analysis of V2G System Based on Integrated Filter Inductor
Cai, H., Jiang, Z., Huang, R., Xu, H., Liu, S., & Xu, J. (2022) · IEEE International Electrical and Energy Conference (CIEEC) · doi:10.1109/cieec54735.2022.9845922 · Cited by 1
“Hence, this type of integrated on-board charging (IOBC) system not only requires lower investment, but also reduces the total size of the system[10-13].”
BackgroundMain Circuit Topology and Electromagnetic Interference of Electric Vehicle Bidirectional Charger
Sun, S., & Zhu, B. (2022) · Journal of Control Science and Engineering · doi:10.1155/2022/9507377 · Cited by 1
“(e three-phase highpower charging is done in the form of charging piles, and its main topology consists of LCL filter, bidirectional AC/DC converter, and isolated DC/DC converter [6].”
BackgroundRetractedCapacitive Link Universal Converters for EV Powertrain
Wei, A., Lehman, B., Pakdelian, S., & Amirabadi, M. (2022) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce50734.2022.9947954 · Cited by 1
“Numerous efforts are conducted towards more compact designs, including mechanical integration of on-board charging (OBC) system [2]–[4] and topology integration by utilizing one or more parts of existing components in the traction system, which can also be referred to as integrated board charging (IBC) system [5]–[13].”
BackgroundDabour, S. M., Aboushady, A. A., Elgenedy, M. A., Gowaid, I. A., Farrag, M. E., Abdel-Khalik, A. S., Massoud, A. M., & Ahmed, S. (2022) · Applied Sciences · doi:10.3390/app122412553 · Cited by 1
Self-citationTaha, R. A., Abdel-Azim, W. E., Shawier, A., Abdel-Khalik, A. S., Hamad, M. S., & Hamdy, R. A. (2022) · International Middle East Power Systems Conference (MEPCON) · doi:10.1109/mepcon55441.2022.10021728 · Cited by 1
“The sixphase stator windings are considered as two three-phase winding sets with two neutral points connected to the grid terminals [9].”
BackgroundSelf-citationMirtchev, A. V., & Tatakis, E. C. (2023) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2023.3266585 · Cited by 1
“The battery chargers are directly linked to the development of EV transportation because they determine the charging time and can affect the lifetime of the battery stack [2].”
BackgroundChaurasiya, S., & Singh, B. (2023) · IEEE India International Conference on Power Electronics · doi:10.1109/iicpe60303.2023.10474633 · Cited by 1
“An overview of both single and three phase interfaced EV charger topologies is discussed in [3]-[4].”
BackgroundKumar, A. D., Gupta, J., & Singh, B. (2024) · IEEE Journal of Emerging and Selected Topics in Industrial Electronics · doi:10.1109/jestie.2024.3389059 · Cited by 1
“Considering mode of operation of presented ac–dc converter, there are three modes of operation namely, discontinuous inductor current mode (DICM) [19], boundary inductor current conduction mode and continuous inductor current mode (CICM) [20], [21], [22].”
MethodShao, M., Zhang, Q., Wei, Z., Yang, L., & Yuping, H. (2024) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2024.3429369 · Cited by 1
“T HE research on integrated on-board chargers (OBCs) has attracted the interest of many researchers in the last two decades [1], [2].”
BackgroundHuang, P.-H., Raval, V., Perez, A., Mendoza, A., Baireddy, N., & Enjeti, P. N. (2024) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce55643.2024.10861440 · Cited by 1
Study on Common-Mode Noise Reduction Methods in Non-Isolated DC-DC Converters
Sasaki, M., & Sasaki, M. (2023) · Institutional Repositories DataBase (IRDB) · Cited by 1
Sustainability in grids with advanced power electronics
Dong, J., Dash, P. S., Kumar, D. S., Liu, Q., & Sharma, A. (2026) · Elsevier eBooks · doi:10.1016/b978-0-443-29210-1.00094-7 · Cited by 1
Technology Roadmap for Heavy-duty Electric Vehicles
Arora, S., Abkenar, A. T., Jayasinghe, S. G., & Tammi, K. (2021) · Elsevier eBooks · doi:10.1016/b978-0-12-818126-3.00011-7
Nine-Phase-based Fractional-Slot Winding Layouts for Integrated EV On-board Battery Chargers
Metwly, M. Y., Abdel-Majeed, M. S., Hemeida, A., Abdel-Khalik, A. S., & Ahmed, S. (2021) · IEEE International Conference on Industrial Technology (ICIT) · doi:10.1109/icit46573.2021.9453476
“Table III summarizes the rotor loss indices under both the charging and propulsion modes of operation for the two investigated slot/pole combinations [26].”
BackgroundSelf-citationMirtchev, A. V., & Tatakis, E. C. (2021) · European Conference on Power Electronics and Applications · doi:10.23919/epe21ecceeurope50061.2021.9570430
Cai, H., Huang, R., Zhai, H., Xu, H., Liu, S., & Xu, J. (2022) · Frontiers in Energy Research · doi:10.3389/fenrg.2022.875706
“extra set of inductors for the purpose of reducing the charging system size (Xiao et al., 2019; Metwly et al., 2020; Wang et al., 2020).”
BackgroundAn Accurate Inductance Model for Three-Phase Integrated on-Board Electric Vehicle Charger
Luo, Z., Cai, H., Xu, H., Liu, S., & Xu, J. (2021) · IEEE Sustainable Power and Energy Conference (iSPEC) · doi:10.1109/ispec53008.2021.9735462
“The integration of charging system and driving system will help to reduce the volume and weight of the vehicle and reduce the cost [4-7].”
BackgroundViatkin, A. (2023) · Springer theses · doi:10.1007/978-3-031-24712-5_1
An Integrated Motor-Driving and Battery-Charging System for EVs Based on a Dual-Motor System
Liu, X., Tong, M., & Sun, L. (2023) · Lecture notes in electrical engineering · doi:10.1007/978-981-99-0408-2_77
Torque Ripple Analysis and Model of Symmetrical Six-Phase Fault-Tolerant PMSM
Feng, Y., Liao, Y., Lin, H., & Xiaoping, W. (2023) · Lecture notes in electrical engineering · doi:10.1007/978-981-99-0451-8_111
Ramesh, K., Kalimuthu, K., & Bharatiraja, C. (2023) · International Conference on Electrical Energy Systems (ICEES) · doi:10.1109/icees57979.2023.10110266
“This power is used in charging of the EV vehicles in three different infrastructure levels namely Level 1, Level 2 and Level 3 charging [11].”
MethodSingle-Phase Single-Stage PFC Converter with Soft Switching for EV Applications
Anshul, Kumar, G. K. N., & Tiwari, H. (2023) · International Conference on Computer, Electronics & Electrical Engineering & their Applications (IC2E3) · doi:10.1109/ic2e357697.2023.10262607
Heat Pump Integrated On-Board Charger
Goodwin, S. P., Odhano, S., & Atkinson, G. J. (2023) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce53617.2023.10362073
Fast Chargers for Plug-In Electric and Hybrid Vehicles
Mi, C. C., Li, S., & Lu, S. (2024) · Green energy and technology · doi:10.1007/978-981-99-3060-9_9
Investigations on FOPID/SMC Based Modified Four-Port Converter for EV Applications
Keerthana, S., Jeevitha, R., & Venmathi, M. (2024) · International Conference on Distributed Computing and Optimization Techniques (ICDCOT) · doi:10.1109/icdcot61034.2024.10516117
“Because of attention in renewable energy system with diverse sources become advanced interfacing motor drive system and at the same time as, scheming numerous power terminal with economical and squashed arrangement [12-14].”
Background
Metadata
- Authors
- Metwly, M. Y., Abdel-Majeed, M. S., Abdel-Khalik, A. S., Hamdy, R. A., Hamad, M. S., & Ahmed, S.
- Affiliations
- Arab Academy for Science, Technology, and Maritime Transport (EG)
- Alexandria University (EG)
- King Abdullah University of Science and Technology (SA)
- ORCID
- Venue
- IEEE Access
- Published
- 2020
- Volume
- 8
- Pages
- 85216-85242
- ISSN
- 2169-3536 (ISSN-L)
- OpenAlex
- W3023670470
- Cited by
- 229
- References
- 111
- Citations by year
- 2026: 16 · 2025: 37 · 2024: 59 · 2023: 41 · 2022: 40 · 2021: 28 · 2020: 8
- FWCI
- 10.04
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Locations
- IEEE Access (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- King Abdullah University of Science and Technology Repository (King Abdullah University of Science and Technology) (submittedVersion, cc-by)
- Funders
- ITIDA’s ITAC Collaborative Funded Project through the category type of Preliminary Research Projects (PRP2018.R25.4)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Motor Design and Analysis
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Sensorless Control of Electric Motors
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced DC-DC Converters
- Keywords
- electric vehicles, fractional-slot concentrated winding, permanent magnet motor, induction motor, single-phase charging, bidirectional power flow, motor winding design
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.