A Review of Integrated On-Board EV Battery Chargers: Advanced Topologies, Recent Developments and Optimal Selection of FSCW Slot/Pole Combination
Open accessThe DOI matches its Crossref record; 109 of the 111 references it cites were found in a registry or an index.
Abstract
Integrated on-board battery chargers (OBCs) have been recently introduced as an optimal/elegant solution to increase electric vehicle (EV) market penetration as well as minimize overall EV cost. Unlike conventional off-board and on-board battery chargers, integrated OBCs exploit the existing propulsion equipment for battery charging without extra bulky components and/or dedicated infrastructure. OBCs are broadly categorized into three-phase and single-phase types with unidirectional or bidirectional power flow. This paper starts with surveying the main topologies introduced in the recent literature employing either induction or permanent magnet motors to realize fully integrated slow (single-phase) and fast (three-phase) on-board EV battery charging systems, with emphasis on topologies that entail no or minimum hardware reconfiguration. Although, permanent magnet (PM) motors with conventional double-layer distributed winding layouts have been deployed in most commercial EV motors, the non-overlapped fractional slot concentrated winding (FSCW) has been the prevailing choice in the most recent permanent magnet motor designs due to its outstanding operational merits. Hence, a thorough investigation of the impact different FSCW stator winding designs have on machine performance under the charging process is presented in this paper. To this end, the induced magnet losses, which represent a challenging demerit of the FSCW, have been used to compare different topologies under both propulsion and charging operation modes. Based on the introduced comparative study, the optimal slot/pole combinations that correspond to the best compromise under both operational modes have been highlighted.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures






































Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“For instance, the dual-use of motor windings in the charging process, as seen in Integrated Charger Inverter (ICI) systems, eliminates the need for separate inductors, reducing weight and improving efficiency [19,118].”
From On-Board Chargers for Electric Vehicles: A Comprehensive Performance and Efficiency Review (2024) · cites this paper as [19]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Yilmaz, M., & Krein, P. T. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2212917 · Cited by 3,118 · cited 4×
“tional or bidirectional power flow capability [5].”
BackgroundInfluentialMultiphase Electric Machines for Variable-Speed Applications
Levi, E. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.918488 · Cited by 2,157 · cited 1×
“The converter rating per phase is reduced by splitting the power among more phases, while offering improved fault tolerance [19].”
BackgroundMultiphase induction motor drives – a technology status review
Levi, E., Bojoi, R., Profumo, F., Toliyat, H. A., & Williamson, S. (2007) · IET Electric Power Applications · doi:10.1049/iet-epa:20060342 · Cited by 1,619 · cited 1×
“Additionally, the decoupling transformations utilized in multiphase systems are quite sophisticated when compared to their three-phase counterparts [21].”
BackgroundSwitched Reluctance Motors and Their Control
Miller, T. J. E. (1993) · Medical Entomology and Zoology · Cited by 1,583
EL-Refaie, A. M. (2010) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2009.2030211 · Cited by 1,373 · cited 1×
“The FSCWhelps reduce end turn length, simplifies manufacturing and enables a slot fill factor approximately equal to 78%, especially when coupled with segmented stator structures [24].”
BackgroundDannehl, J., Wessels, C., & Fuchs, F. W. (2009) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.2008774 · Cited by 747 · cited 1×
“Under the voltage-oriented control method [79], the battery is charged with a constant maximum current until reaching the cut-off voltage, which is a predefined threshold value known as a safety limit at which constant voltage (CV) control begins.”
MethodElectrical Motor Drivelines in Commercial All-Electric Vehicles: A Review
de Santiago, J., Bernhoff, H., Ekergård, B., Eriksson, S., Ferhatovic, S., Waters, R., & Leijon, M. (2012) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2011.2177873 · Cited by 669 · cited 10×
“These two intelligent modules form the SRM electrical drive using five inverter legs.”
BackgroundInfluentialSynthesis of high performance PM motors with concentrated windings
Cros, J., & Viarouge, P. (2002) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2002.1009476 · Cited by 667
Global Trends in High-Power On-Board Chargers for Electric Vehicles
Khaligh, A., & D'Antonio, M. (2019) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2019.2897050 · Cited by 652 · cited 2×
“patible with smart grid functionalities [110].”
BackgroundKhaligh, A., & Dusmez, S. (2012) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2012.2213104 · Cited by 630 · cited 2×
“Considering that most commercial EVs are based on three-phase motors, various integrated chargers employing three-phase machines have been introduced in the literature [4], [36].”
Background
Research works printed but not linked: 3
- IEA, ''Global EV outlook 2019: Scaling-up the transition to electric mobility,'' OECD, Paris, France, 2019.
- AYMAN S. ABDEL-KHALIK (Senior Member, IEEE) received the B.Sc. and M.Sc. degrees in electrical engineering from Alexandria University, Alexandria, Egypt, in 2001 and 2004, respectively, and the Ph.D. degree in electrical engineering from Alexandria University and Strathclyde University, Glasgow, U.K., in 2009, under a Dual Channel Program. He is currently a Professor with the Department of Electrical Engineering, Faculty of Engineering, Alexandria University. His current research interests include electrical machine design and modeling, electric drives, energy conversion, and renewable energy. He serves as an Associate Editor for the IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS and the IET Electric Power Applications Journal. He also serves as the Executive Editor of the Alexandria Engineering Journal.
- RAGI A. HAMDY (Senior Member, IEEE) received the B.Sc. and M.Sc. degrees from Alexan- dria University, Alexandria, Egypt, in 1991 and 1994, respectively, and the Ph.D. degree from Heriot-Watt University, U.K., in 1999. He is currently a Professor with the Department of Electrical Engineering, Faculty of Engineering, Alexandria University. His current research inter- ests include electric machines, electric drives, and power electronics.
Cited by
Items 201–261 of 261
Deng, Z., Du, G., Tiansheng, Z., & Lei, Y. (2024) · International Journal of Circuit Theory and Applications · doi:10.1002/cta.4069
Bhattacharya, P., & Bhattacharya, A. (2024) · International Journal of Advanced Research in Science Communication and Technology · doi:10.48175/ijarsct-18951
Modeling, analysis, and implementations of traction systems for vehicle electrification
Monteiro, V., & Afonso, J. L. (2024) · Elsevier eBooks · doi:10.1016/b978-0-443-13969-7.00005-9
Modelling and Analysis of WPT System For Bidirectional On-Board EV Charging
Palvi, G., & Mishra, A. S. (2024) · IEEE International Conference on Electrical Power and Energy Systems (ICEPES) · doi:10.1109/icepes60647.2024.10653572
“Electric vehicles (EVs) are getting popular in the locomotive industry due to their lower energy use and superior performance over gasoline-powered vehicles [1]-[4].”
BackgroundChen, Y., Tong, M., Sun, L., Liu, X., & Xu, Z. (2024) · IEEE Transportation Electrification Conference and Expo, Asia-Pacific (ITEC Asia-Pacific) · doi:10.1109/itecasia-pacific63159.2024.10738632
Fuel Cell-Fed High Gain DC-DC Boost Converter-Based Onboard Electrical Vehicle Charger System
Gupta, P. P., & Tripathi, R. K. (2024) · Lecture notes in electrical engineering · doi:10.1007/978-981-97-5951-4_9
Zhao, Q., & Liu, X. (2025) · Recent Advances in Electrical & Electronic Engineering (Formerly Recent Patents on Electrical & Electronic Engineering) · doi:10.2174/0123520965360247250112191037
Characteristic Investigation of VFRM Multiplexed as Transformer in Integrated on-Board Charger
Zhao, Q., & Liu, X. (2024) · IEEE China International Youth Conference on Electrical Engineering (CIYCEE) · doi:10.1109/ciycee63099.2024.10846771
“The multiplexing can reduce the cost, weight, and volume of the whole EV [5].”
Fractional Power Based Multi-Utility Fast Charger with V2Aux and V2V Capability
Khan, W. M., Singh, R. K., Mahanty, R., & Lal, V. N. (2024) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce55643.2024.10861338
A soft-switching on-board charger for electric vehicle application
Wei, A., Lehman, B., & Amirabadi, M. (2024) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce55643.2024.10860787
Karneddi, H., & Ronanki, D. (2024) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce55643.2024.10861290
“This undesirable electromagnetic torque results in noise, potential wear on components, and vibrations, degrading the propulsion system’s performance [16], [17].”
An RMRAC-based Adaptive and Robust Control for a Multi-Winding Flyback Converter in OBC Application
Khan, S. A., Hollweg, G. V., Wang, M., Su, W., Chaturvedi, S., Le, D., & Ghavaminejad, M. (2024) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon55916.2024.10905160
Metwly, M. Y., He, J., & Abdel-Khalik, A. S. (2024) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon55916.2024.10905856
“The main merits of IOBCs, besides unity power factor operation at the grid side, are zero average torque production during battery charging and simple hardware reconfiguration to switch between the propulsion and charging operational modes [16].”
Self-citationHarmonic Analysis of EVs Connected to Grid and Suppression of Harmonics with FLC
Vishwakarma, S., Reddy, C. V., Chawla, P., & Surjan, B. S. (2024) · International Conference on Advancement in Electronics & Communication Engineering (AECE) · doi:10.1109/aece62803.2024.10911670
“However, a significant drawback of this system is its slow charging speed, which causes the Battery to take a long time to charge[3]-[4].”
2-Level BDC for Grid-to-Vehicle (G2V) and Vehicle-to-Grid (V2G) Power Transfer
Keerthana, G., Majumder, D., Sutradhar, D., Das, B., Chakrabarti, A., & Kasari, P. R. (2024) · IEEE Silchar Subsection Conference (SILCON) · doi:10.1109/silcon63976.2024.10910574
Mallikarjun, P., & Rajan, G. T. S. (2024) · International Conference on Sustainable Power & Energy (ICSPE) · doi:10.1109/icspe62629.2024.10924389
Planar Magnetics Based Onboard Electric Vehicle Charger with Auxiliary Supply
Pawde, V. S., Keshri, R. K., Saurav, S., Sawarkar, P. D., Suryawanshi, H. M., & Shamal, V. P. (2024) · IEEE International Conference on Power Electronics, Drives and Energy Systems · doi:10.1109/pedes61459.2024.10961793
“To enhance power density as well as to make charging units economical many studies have been done over the period [3], [4], [5], [6], [7], [8].”
Bhumika, B., Kumar, B. U., Vineetha, O., Hussain, C. S. N. A., Ganesh, B., & Kumar, P. M. (2025) · International Journal of Advanced Scientific Technologies in Engineering and Management Sciences · doi:10.22413/ijastems/2025/v11/i3/1
Ananth Angel, Z., Kumar, S. S., & Jebin, B. M. (2025) · International Journal of Electrical and Electronics Engineering · doi:10.14445/23488379/ijeee-v12i4p119
Nassaji, A., Mousavi, M. S., Davari, S. A., Norambuena, M., Aly, M., Flores‐Bahamonde, F., & Rodríguez, J. (2025) · IEEE International Conference on Compatibility, Power Electronics and Power Engineering · doi:10.1109/cpe-powereng63314.2025.11027256
“However, a critical challenge in integrated EV chargers is the unintended generation of torque due to the current flowing through the motor windings during the charging mode [4].”
A model predictive control strategy for enhance performance of totem-pole PFC rectifier
Le, C. D., & Nguyen, T. D. (2025) · International Journal of Power Electronics and Drive Systems/International Journal of Electrical and Computer Engineering · doi:10.11591/ijpeds.v16.i3.pp1687-1700
“…ongoing revolution of electric vehicles (EV) quickly carries out a production ramp-up, propelling us towards a cleaner and more sustainable transportation landscape, in which there is an essential component that silently but indispensably underpins this progress: the onboard charger (OBC) [1], [2].”
A Novel Bidirectional Flying Inductor Inverter Topology
Rakanov, Y. (2023) · National Conference with International Participation (ELECTRONICA) · doi:10.1109/electronica58875.2023.11173896
Rana, N., & Basu, K. (2025) · International Telecommunications Energy Conference (INTELEC) · doi:10.1109/intelec63987.2025.11214728
“In the literature [1]–[4], the traction inverter and motor winding are modified to create a non-isolated single port IOBC, as shown in Fig.”
Anchieri, D., Ricco, M., Monteiro, V., & Mandrioli, R. (2025) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon58223.2025.11221136
“…chargers (where, internally, the AC to DC power conversion is performed), but to realize the requirement of fast charging, the solution lies in off-board chargers (where the AC to DC power conversion is performed externally to the EV and the EV charging is performed directly in DC [5], [6]).”
Bakry, N., Fawzi, M., Abdelsalam, I., & Kalas, A. E. (2025) · IEEE Conference on Power Electronics and Renewable Energy (CPERE) · doi:10.1109/cpere65146.2025.11240088
“In terms of power levels, OBCs are typically categorized as low-power (≤ 3.3 kW), medium-power (3.7–7.4 kW), or high-power (11–22 kW), with higher ratings enabling faster AC charging [14].”
InfluentialShin, Y., Jang, J., Lee, T., & Cho, Y. (2025) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce58356.2025.11260285
“1 [3] – [8].”
Zhai, X., Wei, J., Ding, C., Yang, W., & Zhou, B. (2025) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2025.3632535
“As the motor driving system is reconfigured and multiplexed for on-board battery charging, it also reduces the volume and weight of the proposed system to achieve high power density of electric vehicles (EVs) [1], [2], [3].”
Hamad, M., & Yalman, Y. (2025) · Afyon Kocatepe University Journal of Sciences and Engineering · doi:10.35414/akufemubid.1660346
Self-citationNakkeeran, R., Bharatiraja, C., Padmanaban, S., & Szcześniak, P. (2025) · IEEE International Conference on Recent Advances in Systems Science and Engineering (RASSE) · doi:10.1109/rasse64831.2025.11315256
“Unlike conventional inductive coupling, RIPT uses resonant circuits on both the T X and R X sides, enabling efficient power transmission even over medium distances with coil misalignment or variable air gaps [2,3].”
Omkar, M., & Vijaya Kumar, M. (2025) · International Journal of Electrical and Electronics Engineering · doi:10.14445/23488379/ijeee-v12i12p112
“To overcome these difficulties, studies have devoted more attention to integrated charger-drive systems, where the same hardware is used in propulsion and charging, leading to a better utilisation of energy and reducing the size of the system [3, 5].”
ДЕНИСЕНКО, С. (2025) · A.N.Beketov KNUME Digital Repository (National University of Kharkiv)
SUPER CAPACITOR BUFFERED V2V ENERGY SHARING FOR RIPPLE-FREE MOBILE EV CHARGING
BEGUM, M. G., SATYANARAYANA, D., MYBELLI, S., & BABU, R. S. (2025) · Journal of Science Engineering Technology and Management Sciences · doi:10.64771/jsetms.2025.v02.i05.4pjph0
Transient Response Enhancement of PMD Battery Charger Using Rule-Based Fuzzy Logic Control
Yoon, G., & Bak, Y. (2026) · Mathematics · doi:10.3390/math14040585
Kircioglu, O., & ÇAMUR, S. (2026) · Energies · doi:10.3390/en19041000
Feslı, U. (2026) · Gazi Üniversitesi Fen Bilimleri Dergisi Part C Tasarım ve Teknoloji · doi:10.29109/gujsc.1813580
Pathological changes in abdominal organs detected with ultrasound in dogs with hyperadrenocorticism
Jarockaitė, R., & Laukutė, M. (2023) · Lithuanian University of Health Sciences
Rathee, S., & Pahuja, G. L. (2026) · Istanbul University - Journal of Electrical & Electronics Engineering · doi:10.5152/electrica.2026.25055
“The authors in [11] examine the impact of different FSCW windings on the overall charging process, thereby highlighting the critical role of winding design in integrated charging systems.”
Super capacitor Buffered V2V Energy Sharing for RippleFree Mobile EV Charging
GOLLA, K. K., GADI, V., & SARELLA, A. (2026) · International Journal for Research Trends and Innovation · doi:10.56975/ijrti.v11i3.210435
ELECTRIC VEHICLE TO VEHICLE ENERGY TRANSFER USING ON BOARD CONVERTERS
IJERST (2026) · International Journal of Engineering Research and Science & Technology · doi:10.5281/zenodo.19681604
Review of the optimal location and size for electric vehicle charging stations in Malaysia
Shariff, N. M., Lu, S.-S., Ramli, N., Alexander, C. H. C., & Subhashini, G. K. (2026) · AIP conference proceedings · doi:10.1063/5.0327794
Design and Performance Evaluation of a Bridgeless Zeta Converter for Efficient EV Charging Systems
Vishvanath, M., Reddy, G. C. R., Lokesh, K., Ganiga, S., Venkadesan, A., & Sentamizh Selvan, S. (2025) · IEEE International Conference on Smart Technologies for Power, Energy and Control (STPEC) · doi:10.1109/stpec66316.2025.11490772
Lin, B., Du, G., Deng, Z., Tiansheng, Z., & Lei, Y. (2026) · Energies · doi:10.3390/en19102349
An Integrated Onboard Charger for Tri-Motor Off-Road Electric Vehicles
Afriyie, D., Brakoh, G., Khan, A. A., Jamil, M., & Ahmed, H. F. (2026) · IEEE Journal of Emerging and Selected Topics in Industrial Electronics · doi:10.1109/jestie.2026.3702018
“Most of the integrated OBCs reported in [12], [18], and [22] use permanent magnet synchronous motors (PMSMs), switched reluctance motors, BLDC motors, and induction motors.”
MULTI-FUNCTIONAL PLUG-IN EV ON-BOARD CHARGER FOR SUSTAINABLE TRANSPORTATION
Singh, S. N., Prajapati, A., & Saket, R. K. (2026) · IJESRT · doi:10.64149/j.ijesrt.15.5.1-26
Cost-Effective and High-Power-Density Nonisolated Bidirectional On-Board Charger
Sarnago, H., & Lucía, Ó. (2026) · IEEE Open Journal of the Industrial Electronics Society · doi:10.1109/ojies.2026.3709792
“As a result, a typical two-stage design [12] [see Fig.”
Abbas, M. Q., Rizzoli, G., Mengoni, M., Vancini, L., Boico, G., Zarri, L., & Tani, A. (2026) · IEEE Open Journal of Power Electronics · doi:10.1109/ojpel.2026.3711923
“This can be achieved either by using a dedicated on-board dc–dc converter, which increases cost, weight, and volume, or by reusing the traction machine windings as boost inductors within an integrated charging architecture [22], [23].”
Vancini, L., Seri, P., Mengoni, M., Cardoso, A. J. M., & Cavallini, A. (2026) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2026.3712111
“More recently, their use has expanded to lower power applications, where they provide high power density, improved efficiency, and increased system reliability, enabling integration into electric vehicle traction systems and onboard or integrated charging architectures [6], [7], [8], [9], [10].”
Dynamic Characteristics Improvement of PMD Battery Charger with Fuzzy Logic Control
Yoon, G., Cho, S., & Bak, Y. (2026) · International Power Electronics Conference (IPEC) · doi:10.23919/ipec-nagasaki2026-ec64663.2026.11597578
Usman, M., Ahmed, A. R., Ali, M. S., Irshad, M., Basha, M. S., Abbas, N., & Samykano, M. (2026) · Energy Conversion and Management X · doi:10.1016/j.ecmx.2026.102167
Hamad, M., & Yalman, Y. (2026) · Engineering Science and Technology an International Journal · doi:10.1016/j.jestch.2026.102493 · Cited by 1
Self-citationRao, B. N., Surabhi, S. L., & Mohan, V. C. J. (2026) · International Conference on Power, Control and Computing Technologies (ICPC2T) · doi:10.1109/icpc2t68221.2026.11646322
“Those autos that were initially only experiments have now turned into a good solution to the problem of air pollution, as well as, for the reduction of the use of non-renewable fossil fuel [1], [2].”
BIDIRECTIONAL ELECTRIC VEHICLE-TO-VEHICLE POWER TRANSFER THROUGH INTEGRATED MOTOR DRIVE SYSTEM
1DR.K.S.C.G MAURYAN2 .MR. K. RAJASEKHA, 3. B. (2026) · International Journal of AI Electrical Civil and Mechanical engineering · doi:10.64751/1v1qa709
Design of a solar-powered charging station for electric vehicle
Putera, P. (2026) · Nottingham ePrints (University of Nottingham)
ON BOARD POWER CONVERSION FOR DIRECT VEHICLE TO VEHICLE CHARGING
1 Mrs. B. Pallavi, 2. C. Y. (2026) · International Journal of Engineering Research and Science & Technology
Artificial Neural Network-Based Control for Enhanced V2V Energy Transfer in Electric Vehicles
Reddy, S. B., Renuka, M., Kumar, M. S. A., Kanchana, M. R., & Sekhar, V. (2025) · Utilitas Mathematica
ELEKTRİKLİ ARAÇLAR İÇİN YÜKSEK VERİMLİ ÇİFT YÖNLÜ ENERJİ TRANSFER SİSTEMİ
ÇOBAN, M., & AKIN, B. (2024) · Yildiz Technical University - AVESIS
Lee, J.-A., Sim, D. H., & Lee, B. (2026) · Journal of Electrical Engineering and Technology · doi:10.1007/s42835-026-02942-2
Panda, G. S., Choudhary, A., Mohanty, P., Mishra, R. N., & Pati, N. (2026) · International Conference on Intelligent Computing and Sustainable Innovations in Technology (IC-SIT) · doi:10.1109/ic-sit69723.2026.11736087
“Metwly et al. extend this perspective by introducing integrated charger concepts that combine propulsion and charging hardware, focusing on structural optimization, electromagnetic design considerations, slot – pole selection, and improved power density through component reuse [2].”
MOCS-Optimized Modified Semi-Half-Bridge Architecture for Efficient Solar-to-EV Energy Transfer
Latha, P., Vaidhehi, M., Geetha, S., Malathi, G., Manivasagam, R., & Jeyasudha, S. (2026) · International Conference on Intelligent Cyber Physical Systems and Internet of Things (ICoICI) · doi:10.1109/icoici69824.2026.11723982
“…optimization of various circuit topologies for use in PV-assisted electric vehicle charging has, more recently, become a central theme with an emphasis on improved efficiency and reduction of electrical stress, lower ripples, flexible and smart charging in fluctuating renewable conditions [8]-[12].”
Latha, P., Vaidhehi, M., Gayathri, S., Rathika, S., Naidu, G., & Jeyasudha, S. (2026) · International Conference on I-SMAC (IoT in Social, Mobile, Analytics and Cloud) (I-SMAC) · doi:10.1109/i-smac70384.2026.11747817
“Therefore, converter-controller integration must be both computationally effective and scalable for real-world applications, while also addressing the issues of energy efficiency, current regulation, and harmonic reduction [16-17], and [20].”
Abbas, M. Q., Rizzoli, G., Mengoni, M., Vancini, L., Zarri, L., & Tani, A. (2026) · International Conference on Electrical Machines (ICEM) · doi:10.1109/icem68283.2026.11757870
Metadata
- Authors
- Metwly, M. Y., Abdel-Majeed, M. S., Abdel-Khalik, A. S., Hamdy, R. A., Hamad, M. S., & Ahmed, S.
- Affiliations
- Arab Academy for Science, Technology, and Maritime Transport (EG)
- Alexandria University (EG)
- King Abdullah University of Science and Technology (SA)
- ORCID
- Venue
- IEEE Access
- Published
- 2020
- Volume
- 8
- Pages
- 85216-85242
- ISSN
- 2169-3536 (ISSN-L)
- OpenAlex
- W3023670470
- Cited by
- 229
- References
- 111
- Citations by year
- 2026: 16 · 2025: 37 · 2024: 59 · 2023: 41 · 2022: 40 · 2021: 28 · 2020: 8
- FWCI
- 10.04
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Locations
- IEEE Access (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- King Abdullah University of Science and Technology Repository (King Abdullah University of Science and Technology) (submittedVersion, cc-by)
- Funders
- ITIDA’s ITAC Collaborative Funded Project through the category type of Preliminary Research Projects (PRP2018.R25.4)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Motor Design and Analysis
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Sensorless Control of Electric Motors
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced DC-DC Converters
- Keywords
- electric vehicles, fractional-slot concentrated winding, permanent magnet motor, induction motor, single-phase charging, bidirectional power flow, motor winding design
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.