A Review of Integrated On-Board EV Battery Chargers: Advanced Topologies, Recent Developments and Optimal Selection of FSCW Slot/Pole Combination
Open accessThe DOI matches its Crossref record; 109 of the 111 references it cites were found in a registry or an index.
Abstract
Integrated on-board battery chargers (OBCs) have been recently introduced as an optimal/elegant solution to increase electric vehicle (EV) market penetration as well as minimize overall EV cost. Unlike conventional off-board and on-board battery chargers, integrated OBCs exploit the existing propulsion equipment for battery charging without extra bulky components and/or dedicated infrastructure. OBCs are broadly categorized into three-phase and single-phase types with unidirectional or bidirectional power flow. This paper starts with surveying the main topologies introduced in the recent literature employing either induction or permanent magnet motors to realize fully integrated slow (single-phase) and fast (three-phase) on-board EV battery charging systems, with emphasis on topologies that entail no or minimum hardware reconfiguration. Although, permanent magnet (PM) motors with conventional double-layer distributed winding layouts have been deployed in most commercial EV motors, the non-overlapped fractional slot concentrated winding (FSCW) has been the prevailing choice in the most recent permanent magnet motor designs due to its outstanding operational merits. Hence, a thorough investigation of the impact different FSCW stator winding designs have on machine performance under the charging process is presented in this paper. To this end, the induced magnet losses, which represent a challenging demerit of the FSCW, have been used to compare different topologies under both propulsion and charging operation modes. Based on the introduced comparative study, the optimal slot/pole combinations that correspond to the best compromise under both operational modes have been highlighted.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures






































Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“For instance, the dual-use of motor windings in the charging process, as seen in Integrated Charger Inverter (ICI) systems, eliminates the need for separate inductors, reducing weight and improving efficiency [19,118].”
From On-Board Chargers for Electric Vehicles: A Comprehensive Performance and Efficiency Review (2024) · cites this paper as [19]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Yilmaz, M., & Krein, P. T. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2212917 · Cited by 3,118 · cited 4×
“tional or bidirectional power flow capability [5].”
BackgroundInfluentialMultiphase Electric Machines for Variable-Speed Applications
Levi, E. (2008) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.918488 · Cited by 2,157 · cited 1×
“The converter rating per phase is reduced by splitting the power among more phases, while offering improved fault tolerance [19].”
BackgroundMultiphase induction motor drives – a technology status review
Levi, E., Bojoi, R., Profumo, F., Toliyat, H. A., & Williamson, S. (2007) · IET Electric Power Applications · doi:10.1049/iet-epa:20060342 · Cited by 1,619 · cited 1×
“Additionally, the decoupling transformations utilized in multiphase systems are quite sophisticated when compared to their three-phase counterparts [21].”
BackgroundSwitched Reluctance Motors and Their Control
Miller, T. J. E. (1993) · Medical Entomology and Zoology · Cited by 1,583
EL-Refaie, A. M. (2010) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2009.2030211 · Cited by 1,373 · cited 1×
“The FSCWhelps reduce end turn length, simplifies manufacturing and enables a slot fill factor approximately equal to 78%, especially when coupled with segmented stator structures [24].”
BackgroundDannehl, J., Wessels, C., & Fuchs, F. W. (2009) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.2008774 · Cited by 747 · cited 1×
“Under the voltage-oriented control method [79], the battery is charged with a constant maximum current until reaching the cut-off voltage, which is a predefined threshold value known as a safety limit at which constant voltage (CV) control begins.”
MethodElectrical Motor Drivelines in Commercial All-Electric Vehicles: A Review
de Santiago, J., Bernhoff, H., Ekergård, B., Eriksson, S., Ferhatovic, S., Waters, R., & Leijon, M. (2012) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2011.2177873 · Cited by 669 · cited 10×
“These two intelligent modules form the SRM electrical drive using five inverter legs.”
BackgroundInfluentialSynthesis of high performance PM motors with concentrated windings
Cros, J., & Viarouge, P. (2002) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2002.1009476 · Cited by 667
Global Trends in High-Power On-Board Chargers for Electric Vehicles
Khaligh, A., & D'Antonio, M. (2019) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2019.2897050 · Cited by 652 · cited 2×
“patible with smart grid functionalities [110].”
BackgroundKhaligh, A., & Dusmez, S. (2012) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2012.2213104 · Cited by 630 · cited 2×
“Considering that most commercial EVs are based on three-phase motors, various integrated chargers employing three-phase machines have been introduced in the literature [4], [36].”
BackgroundDesign considerations for fractional-slot winding configurations of synchronous machines
Bianchi, N., Bolognani, S., Pre, M. D., & Grezzani, G. (2006) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2006.876070 · Cited by 447
Optimal Flux Weakening in Surface PM Machines Using Fractional-Slot Concentrated Windings
EL-Refaie, A. M., & Jahns, T. M. (2005) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2005.847312 · Cited by 400 · cited 1×
“These factors are presented comprehensively in the literature [92]–[95].”
BackgroundWinding factors and Joule losses of permanent magnet machines with concentrated windings
Magnussen, F., & Sadarangani, C. (2003) · IEEE International Electric Machines and Drives Conference, 2003. IEMDC'03. · doi:10.1109/iemdc.2003.1211284 · Cited by 395
Integration of Vehicle-to-Grid in the Western Danish Power System
Pillai, J. R., & Bak-Jensen, B. (2010) · IEEE Transactions on Sustainable Energy · doi:10.1109/tste.2010.2072938 · Cited by 388 · cited 1×
“Almost all indicated topologies support vehicleto-grid (V2G) integration [34], [35].”
BackgroundGrid-Connected Integrated Battery Chargers in Vehicle Applications: Review and New Solution
Haghbin, S., Lundmark, S., Alakula, M., & Carlson, O. (2013) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2012.2187414 · Cited by 345 · cited 3×
“Moreover, single-phase charging corresponds to a pulsating charging power that undesirably affects battery lifetime [4], [37], [39].”
BackgroundPerformance Analysis of Current BEVs Based on a Comprehensive Review of Specifications
Grunditz, E. A., & Thiringer, T. (2016) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2016.2571783 · Cited by 329 · cited 1×
“According to the analysis of battery electric vehicles (BEVs) introduced in [11], the PMSM is the most commonly used type in current BEVs.”
BackgroundRotor loss in permanent-magnet brushless AC machines
Stone, D. A., Mellor, P. H., Howe, D., & Atallah, K. (2000) · IEEE Transactions on Industry Applications · doi:10.1109/28.887213 · Cited by 326 · cited 1×
“As far as the rotor eddy current losses are concerned for this winding layout, many models were introduced to compute the rotor losses [86], [87], while some other indices were introduced to assess the severity of this loss component for a given winding design [88].”
MethodRotor loss in permanent magnet brushless AC machines
Atallah, K., Howe, D., Mellor, P. H., & Stone, D. A. (2003) · IEEE International Electric Machines and Drives Conference. IEMDC'99. Proceedings (Cat. No.99EX272) · doi:10.1109/iemdc.1999.769027 · Cited by 308
Levi, E., Jones, M., Vukosavic, S. N., & Toliyat, H. A. (2004) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2003.823241 · Cited by 274 · cited 2×
“ing modes) in order to excite the proper machine subspace under each mode [63].”
BackgroundAn Integral Battery Charger With Power Factor Correction for Electric Scooter
Pellegrino, G., Armando, E., & Guglielmi, P. (2010) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2009.2033187 · Cited by 267
Use of the star of slots in designing fractional-slot single-layer synchronous motors
Bianchi, N., & Dai Pré, M. (2006) · IEE Proceedings - Electric Power Applications · doi:10.1049/ip-epa:20050284 · Cited by 263 · cited 1×
“The definition of a specific slot/pole combination viability is based on the corresponding star of slots [96], which is first determined based on motoring mode.”
BackgroundInnovation by in-wheel-motor drive unit
Murata, S. (2012) · Vehicle System Dynamics · doi:10.1080/00423114.2012.666354 · Cited by 241 · cited 1×
“Recent designs, however, introduced low speed in-wheelmotor structures to avoid friction losses and maintain full torque capabilities [22].”
BackgroundNonconventional on-board charger for electric vehicle propulsion batteries
Solero, L. (2001) · IEEE Transactions on Vehicular Technology · doi:10.1109/25.917904 · Cited by 210 · cited 2×
“An interesting solution based on an axial flux permanent magnet (PM) machine has been described in [45], and is shown in Fig.”
MethodDajaku, G., Xie, W., & Gerling, D. (2014) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2013.2294754 · Cited by 187 · cited 2×
“Also, the interaction between these low order harmonics causes audible noise and vibrations in the mechanical structure [29].”
BackgroundShi, C., Tang, Y., & Khaligh, A. (2017) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2017.2729345 · Cited by 187 · cited 2×
“An innovative charger that underpins the same concept has also been presented earlier in [8].”
BackgroundWang, J., Yuan, X., & Atallah, K. (2013) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2012.2227867 · Cited by 184
An Electrolytic Capacitorless Bidirectional EV Charger for V2G and V2H Applications
Kwon, M., & Choi, S. (2017) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2016.2630711 · Cited by 177 · cited 1×
“Almost all indicated topologies support vehicleto-grid (V2G) integration [34], [35].”
BackgroundAn Isolated High-Power Integrated Charger in Electrified-Vehicle Applications
Haghbin, S., Lundmark, S., Alakula, M., & Carlson, O. (2011) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2011.2162258 · Cited by 174 · cited 1×
“An isolated charger that employs a PMSM with two threephase stator winding sets is manifested in [59], as depicted in Fig.”
BackgroundOnboard Integrated Battery Charger for EVs Using an Asymmetrical Nine-Phase Machine
Subotic, I., Bodo, N., Levi, E., & Jones, M. (2015) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2014.2345341 · Cited by 174 · cited 6×
“Balanced three-phase grid currents can be ensured by controlling the current components of the subspace αβ3 and the zero sequence current component based on the desired charging current level [50].”
BackgroundMethodInfluentialSlot Harmonic Impact on Rotor Losses in Fractional-Slot Permanent-Magnet Machines
Fornasiero, E., Bianchi, N., & Bolognani, S. (2011) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2011.2168794 · Cited by 169 · cited 1×
“On the other hand, the air gap flux distribution of FSCWs is extremely distorted due to different sub and super space harmonics with relatively high magnitudes [26], [27].”
BackgroundMeier, F. (2008) · KTH Publication Database DiVA (KTH Royal Institute of Technology) · Cited by 165
A combined multiphase electric drive and fast battery charger for Electric Vehicles
De Sousa, L., Silvestre, B., & Bouchez, B. (2010) · 2010 IEEE Vehicle Power and Propulsion Conference · doi:10.1109/vppc.2010.5729057 · Cited by 165 · cited 1×
“An interesting high-power integrated charger that supports fast three-phase charging has been described in [53] and is shown in Fig.”
BackgroundCarraro, E., Bianchi, N., Zhang, S., & Koch, M. A. (2018) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2018.2807382 · Cited by 162 · cited 1×
“Some of them are based on non-overlapped FSCW windings such as 12-slot/10-pole [30] and 18-slot/16-pole [31] combinations, while others are based on overlapped windings with a coil”
BackgroundDiab, M. S., Elserougi, A. A., Abdel-Khalik, A. S., Massoud, A. M., & Ahmed, S. (2016) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2016.2555295 · Cited by 159
Self-citationA Three-Phase Integrated Onboard Charger for Plug-In Electric Vehicles
Shi, C., Tang, Y., & Khaligh, A. (2018) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2017.2727398 · Cited by 159 · cited 1×
“A simple solution that employs an additional three-phase interface converter to obtain a highpower three-phase integrated on-board charging has been investigated in [67] and is shown in Fig.”
MethodAn integral battery charger for four-wheel drive electric vehicle
Sul, S.-K., & Lee, S.-J. (1995) · IEEE Transactions on Industry Applications · doi:10.1109/28.464524 · Cited by 158 · cited 1×
“A fourmotor-drive based integrated charger has been introduced in [44].”
Investigation on Pole-Slot Combinations for Permament Magnet Machines with Concentrated Windings
Libert, F., & Soulard, J. (2004) · International Conference on Electrical Machines (ICEM) · Cited by 157
Single-Phase On-Board Integrated Battery Chargers for EVs Based on Multiphase Machines
Subotic, I., Bodo, N., & Levi, E. (2016) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2015.2504400 · Cited by 157 · cited 2×
“Moreover, single-phase charging corresponds to a pulsating charging power that undesirably affects battery lifetime [4], [37], [39].”
BackgroundMethodMapelli, F. L., Tarsitano, D., & Mauri, M. (2010) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2009.2029520 · Cited by 150 · cited 1×
“In addition to numerous electrochemistry and material challenges, the performance of battery modules is affected by module design/packaging as well as electrical charging and discharging characteristics [2], [3].”
BackgroundAn integrated fast battery charger for Electric Vehicle
Lacroix, S., Laboure, E., & Hilairet, M. (2010) · 2010 IEEE Vehicle Power and Propulsion Conference · doi:10.1109/vppc.2010.5729063 · Cited by 150 · cited 1×
“Charging from both single-phase (slow) and three-phase (fast) grid is applicable with some modifications such as the use of only two H-bridge inverters, as well as two coils of the machine [56].”
BackgroundIsolated Chargers for EVs Incorporating Six-Phase Machines
Subotic, I., Bodo, N., Levi, E., Jones, M., & Levi, V. (2016) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2015.2412516 · Cited by 147 · cited 4×
“While the one presented in [51] introduces an isolated system located outside the vehicle, that employs a six-phase machine (both symmetrical and asymmetrical configurations, which are explained later in the following subsection).”
BackgroundInfluentialBala, S., Tengner, T., Rosenfeld, P., & Delince, F. (2012) · 2012 IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2012.6342318 · Cited by 144 · cited 1×
“In addition to numerous electrochemistry and material challenges, the performance of battery modules is affected by module design/packaging as well as electrical charging and discharging characteristics [2], [3].”
BackgroundAbdel-Khalik, A. S., Ahmed, S., & Massoud, A. M. (2014) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2014.2364988 · Cited by 142 · cited 3×
“Even though these losses are lower than the stator losses, their effect is crucial on machine performance [27].”
BackgroundSelf-citationSubotic, I., Bodo, N., Levi, E., Dumnic, B., Milicevic, D., & Katic, V. (2016) · IET Electric Power Applications · doi:10.1049/iet-epa.2015.0292 · Cited by 141 · cited 1×
“based on multiphase drivetrains are considered in [37], [38].”
MethodAn EV Drive-Train With Integrated Fast Charging Capability
Subotic, I., Bodo, N., & Levi, E. (2016) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2015.2424592 · Cited by 133 · cited 5×
“A five-phase machine approach (non-isolated method) is utilized in [52].”
BackgroundMethodInfluentialA Novel 24-Slots/10-Poles Winding Topology for Electric Machines
Dajaku, G., & Gerling, D. (2011) · IEEE International Electric Machines & Drives Conference (IEMDC) · doi:10.1109/iemdc.2011.5994889 · Cited by 132 · cited 1×
“As a result of employing this technique, several interesting slot/pole combinations have shown promise in EV applications, namely 24-slot/10-pole [32], [99] and 18-slot/10-pole [33].”
MethodAn Integrated Driving/Charging Switched Reluctance Motor Drive Using Three-Phase Power Module
Chang, H.-C., & Liaw, C.-M. (2011) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2051938 · Cited by 129 · cited 1×
“An integrated on-board battery charger using a switched reluctance motor (SRM) is described in [47].”
MethodComprehensive analysis of high quality power converters for level 3 off-board chargers
Dusmez, S., Cook, A., & Khaligh, A. (2011) · 2011 IEEE Vehicle Power and Propulsion Conference · doi:10.1109/vppc.2011.6043096 · Cited by 123 · cited 1×
“To fully charge the battery, the reference power is set to about 10% of its initial value to complete the rest of the charging process, as thoroughly explained in [78].”
BackgroundReddy, P. B., Huh, K., & EL-Refaie, A. M. (2014) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2013.2297515 · Cited by 122
Zhu, Z. Q., Jamil, M. L. M., & Wu, L. (2012) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2012.2229373 · Cited by 121
A study on eddy-current losses in rotors of surface permanent-magnet synchronous machines
Nakano, M., Kometani, H., & Kawamura, M. (2006) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2006.870037 · Cited by 117 · cited 1×
“magnets yielding inevitable thermal demagnetization [28].”
Six-Phase Supply Feasibility Using a PM Fractional-Slot Dual Winding Machine
Barcaro, M., Bianchi, N., & Magnussen, F. (2011) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2011.2161859 · Cited by 116
An SCR Inverter with an Integral Battery Charger for Electric Vehicles
Thimmesch, D. (1985) · IEEE Transactions on Industry Applications · doi:10.1109/tia.1985.349573 · Cited by 112 · cited 1×
“The single-phase integrated charger initially introduced in 1985 [40] is shown in Fig.”
BackgroundIntegration of Six-Phase EV Drivetrains Into Battery Charging Process With Direct Grid Connection
Subotic, I., Bodo, N., & Levi, E. (2017) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2017.2679280 · Cited by 112 · cited 1×
“Another solution that offers the cheapest integration technique with a charging power equal to motoring power is discussed in [64].”
BackgroundEfficiency Evaluation of Fully Integrated On-Board EV Battery Chargers With Nine-Phase Machines
Bodo, N., Levi, E., Subotic, I., Espina, J., Empringham, L., & Johnson, C. M. (2017) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2016.2606657 · Cited by 104
Reddy, P. B., EL-Refaie, A. M., & Huh, K. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2328579 · Cited by 102
Patel, V. I., Wang, J., Wang, W., & Chen, X. (2014) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2014.2301871 · Cited by 99 · cited 1×
“was adopted to mitigate the aforementioned demerits while increasing fault-tolerance capability [84].”
A Voltage-Based Controller for an Electric-Vehicle Charger
Al-Awami, A. T., Sortomme, E., Akhtar, G. M. A., & Faddel, S. (2015) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2015.2481712 · Cited by 91 · cited 1×
“In CV mode, the voltage across the DClink is maintained constant until the current drops to preset minimum values from its maximum indicating a full charge is fulfilled [80].”
BackgroundIndex of rotor losses in three-phase fractional-slot permanent magnet machines
Bianchi, N., & Fornasiero, E. (2009) · IET Electric Power Applications · doi:10.1049/iet-epa.2008.0151 · Cited by 87 · cited 4×
“The rotor loss index (Ri) has been introduced in literature to assess the rotor loss impact of different slot/pole combinations and is governed by (3) [87];”
BackgroundMethodInfluentialAbdel-Khalik, A. S., Ahmed, S., & Massoud, A. M. (2016) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2016.2535230 · Cited by 83 · cited 2×
“As a result of employing this technique, several interesting slot/pole combinations have shown promise in EV applications, namely 24-slot/10-pole [32], [99] and 18-slot/10-pole [33].”
BackgroundMethodSelf-citationShah, M. R., & Lee, S. B. (2006) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2006.873671 · Cited by 81
Simple Carrier-Based PWM Technique for a Three-to-Nine-Phase Direct AC–AC Converter
Ahmed, S. M., Iqbal, A., Abu‐Rub, H., Rodríguez, J., Rojas, C. A., & Saleh, M. (2011) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2011.2134062 · Cited by 79 · cited 1×
“former [71], [72] or power electronic converters [73], [74].”
BackgroundSelf-citationOn-board bidirectional battery chargers topologies for plug-in hybrid electric vehicles
Fahem, K., Chariag, D. E., & Sbita, L. (2017) · 2017 International Conference on Green Energy Conversion Systems (GECS) · doi:10.1109/gecs.2017.8066189 · Cited by 79 · cited 1×
“Various topologies and control schemes of on-board chargers have been presented in [7].”
BackgroundDhulipati, H., Ghosh, E., Mukundan, S., Korta, P., Tjong, J., & Kar, N. C. (2019) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2019.2933619 · Cited by 79
An Effective Charging-Torque Elimination Method for Six-Phase Integrated On-Board EV Chargers
Xiao, Y., Liu, C., & Yu, F. Y. (2019) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2019.2924538 · Cited by 78 · cited 2×
“Newly added techniques to eliminate torque production during the charging operation on the basis of multiphase machine degrees of freedom have been investigated in [66], [9].”
BackgroundA review of single-phase on-board integrated battery charging topologies for electric vehicles
Subotic, I., & Levi, E. (2015) · 2015 IEEE Workshop on Electrical Machines Design, Control and Diagnosis (WEMDCD) · doi:10.1109/wemdcd.2015.7194522 · Cited by 74 · cited 2×
“• Maximizing the charging efficiency [39].”
BackgroundAhmed, S. M., Iqbal, A., & Abu‐Rub, H. (2010) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2098373 · Cited by 71
Self-citationBruyere, A., De Sousa, L., Bouchez, B., Sandulescu, P., Kestelyn, X., & Semail, E. (2010) · 2010 IEEE Vehicle Power and Propulsion Conference · doi:10.1109/vppc.2010.5729220 · Cited by 69 · cited 1×
“Several solutions employing the same arrangement are presented in the literature [55]–[58].”
MethodEL-Refaie, A. M., Shah, M. R., Qu, R., & Kern, J. M. (2008) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2008.2002207 · Cited by 68 · cited 4×
“The machines with a higher lowest common multiple (LCM) between their slot and pole numbers offer lower cogging torque [25].”
BackgroundMethodInfluentialA Novel Three-Phase to Five-Phase Transformation Using a Special Transformer Connection
Iqbal, A., Moinuddin, S., Khan, M. R., Ahmed, S. M., & Abu‐Rub, H. (2010) · IEEE Transactions on Power Delivery · doi:10.1109/tpwrd.2010.2042307 · Cited by 68 · cited 1×
“former [71], [72] or power electronic converters [73], [74].”
BackgroundSelf-citationA Review of on-Board Integrated Electric Vehicles Charger and a New Single-Phase Integrated Charger
Harbin Institute of Technology, Na, T., Yuan, X., Harbin Institute of Technology, Tang, J., Harbin Institute of Technology, hang, Q. Z., & Harbin Institute of Technology (2019) · CPSS Transactions on Power Electronics and Applications · doi:10.24295/cpsstpea.2019.00027 · Cited by 68 · cited 1×
“Unlike three-phase charging, the battery current under single-phase charging will experience a pulsating current component at double the line frequency, which has been addressed using innovative converter topologies in [49].”
BackgroundZheng, P., Wu, F., Lei, Y., Sui, Y., & Yu, B. (2013) · Energies · doi:10.3390/en6104980 · Cited by 67
Viana, C. C. D., & Lehn, P. W. (2019) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2019.2925211 · Cited by 65
A Two-Stage Three-Phase Integrated Charger for Electric Vehicles With Dual Cascaded Control Strategy
Shi, C., & Khaligh, A. (2018) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2018.2797913 · Cited by 62 · cited 1×
“Moreover, it may be considered as a cost-effective solution due to the omission of a second conversion stage [68].”
BackgroundFlux‐weakening operation of open‐end winding drive integrating a cost‐effective high‐power charger
Sandulescu, A., Meinguet, F., Kestelyn, X., Semail, E., & Bruyère, A. (2013) · IET Electrical Systems in Transportation · doi:10.1049/iet-est.2012.0026 · Cited by 60
Modular Tri-Port High-Power Converter for SRM Based Plug-in Hybrid Electrical Trucks
Hu, Y., Gan, C., Sun, Q., Li, P., Wu, J., & Wen, H. (2017) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2017.2701784 · Cited by 60 · cited 1×
“As an integrated OBC machine candidate, SRMs can produce zero average torque during charging, and their flexible energy flow control in EV applications is discussed in [16].”
MethodBai, Y., Yang, X., Zhang, D., Li, X., Chen, W., & Hu, W. (2016) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2016.2579679 · Cited by 59 · cited 1×
“Themain function of the EMI filter is to reduce highfrequency electromagnetic noise [54].”
BackgroundEnhanced Availability of Drivetrain Through Novel Multiphase Permanent-Magnet Machine Drive
Patel, V. I., Wang, J., Nugraha, D. T., Vuletić, R., & Tousen, J. (2015) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2015.2435371 · Cited by 56
Postfault Operation of a Nine-Phase Six-Terminal Induction Machine Under Single Open-Line Fault
Abdel-Khalik, A. S., Hamad, M. S., Massoud, A. M., & Ahmed, S. (2017) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2017.2733471 · Cited by 53 · cited 1×
“tion was introduced for a high-power multiphase induction machine in [12], [60].”
MethodSelf-citationWang, K., Zhu, Z. Q., Ombach, G., Koch, M. A., Zhang, S., & Xu, J. (2014) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2014.2316362 · Cited by 48 · cited 2×
“As a result of employing this technique, several interesting slot/pole combinations have shown promise in EV applications, namely 24-slot/10-pole [32], [99] and 18-slot/10-pole [33].”
BackgroundMethodMultilayer Windings Effect on Interior PM Machines for EV Applications
Wang, Y., Qu, R., & Li, J. (2014) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2014.2385934 · Cited by 47 · cited 1×
“Considerable reported work has been aimed at reducing the effect of eddy current loss, the associated noise, and undesirable vibration due to sub, super, and slot harmonics [90], [97], [109].”
BackgroundThree-Phase to Seven-Phase Power Converting Transformer
Moinoddin, S., Iqbal, A., Abu‐Rub, H., Khan, M. R., & Ahmed, S. M. (2012) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2012.2201483 · Cited by 43 · cited 1×
“former [71], [72] or power electronic converters [73], [74].”
BackgroundSelf-citationAbdel‐Khalik, A. S., Massoud, A., & Ahmed, S. (2018) · IET Electric Power Applications · doi:10.1049/iet-epa.2017.0319 · Cited by 39 · cited 2×
“On the other hand, PMSMs have the highest efficiency among all other EV drivelines [13].”
BackgroundMethodSelf-citationAbdel-Khalik, A. S., Ahmed, S., & Massoud, A. M. (2016) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2016.2626240 · Cited by 34 · cited 2×
“tion was introduced for a high-power multiphase induction machine in [12], [60].”
BackgroundMethodSelf-citationChinmaya, K. A., & Singh, G. K. (2018) · IET Electrical Systems in Transportation · doi:10.1049/iet-est.2018.5015 · Cited by 34 · cited 1×
“Whereas, the one in [65] employs an asymmetrical six-phase induction motor with the option of two-source”
BackgroundRelationship between rated torque andsize of permanentmagnet machines
Binns, K. J., & Shimmin, D. W. (1996) · IEE Proceedings - Electric Power Applications · doi:10.1049/ip-epa:19960776 · Cited by 33 · cited 1×
“However, the relation between the machine torque and size stands as the main challenge in order to achieve this vision [23].”
BackgroundAn integrated battery charger for EVs based on an asymmetrical six-phase machine
Subotić, I., LEVI, E., Jones, M., & Graovac, D. (2013) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon.2013.6700337 · Cited by 33
Tang, L., & Su, G.-J. (2010) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2010.5617711 · Cited by 32 · cited 1×
“An improved solution for controlling such a system, that incorporates the same configuration, is discussed in [42], FIGURE 2.”
BackgroundAbdel-Khalik, A. S., Ahmed, S., & Massoud, A. M. (2016) · IET Electric Power Applications · doi:10.1049/iet-epa.2015.0520 · Cited by 31 · cited 2×
“Various slot/pole combinations have been introduced in the literature employing three-phase [91], four-phase [25], fivephase [89], and six-phase [25] configurations.”
BackgroundMethodSelf-citationZhu, Z. Q., Wu, D., & Xiao, G. (2016) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2016.2553140 · Cited by 27
IoT-Based Supervisory Control of an Asymmetrical Nine-Phase Integrated on-Board EV Battery Charger
Metwly, M. Y., Abdel-Majeed, M. S., Abdel-Khalik, A. S., Torki, M., Hamdy, R. A., Hamad, M. S., & Ahmed, S. (2020) · IEEE Access · doi:10.1109/access.2020.2984737 · Cited by 26 · cited 1×
“• Optimization of V2G and G2V operational modes by employing information and communication enabling technologies [111].”
BackgroundSelf-citationAn integrated battery charger for EVs based on a symmetrical six-phase machine
Subotic, I., & Levi, E. (2014) · 2014 IEEE 23rd International Symposium on Industrial Electronics (ISIE) · doi:10.1109/isie.2014.6864937 · Cited by 24 · cited 2×
“Integrated chargers on the basis of an asymmetrical six-phase [75], a five-phase [76], and a symmetrical six-phase [77] power supply are demonstrated in the literature.”
BackgroundSix-phase supply feasibility using a PM fractional-slot dual winding machine
Barcaro, M., Bianchi, N., & Magnussen, F. (2010) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2010.5617862 · Cited by 24
Zhu, S., Cox, T., Xu, Z., & Gerada, C. (2019) · The Journal of Engineering · doi:10.1049/joe.2018.8085 · Cited by 23 · cited 3×
“Considerable reported work has been aimed at reducing the effect of eddy current loss, the associated noise, and undesirable vibration due to sub, super, and slot harmonics [90], [97], [109].”
BackgroundPires, V. F., Monteiro, J., Cordeiro, A., & Silva, J. F. (2019) · Electronics · doi:10.3390/electronics8101199 · Cited by 22
A bearingless coaxial magnetic gearbox
Abdel-Khalik, A. S., Ahmed, S., & Massoud, A. M. (2014) · Alexandria Engineering Journal · doi:10.1016/j.aej.2014.06.002 · Cited by 19 · cited 1×
“These advantages include high slot fill factor, low cogging torque [81], short end turns, high efficiency, and flux weakening capability [82], [83].”
BackgroundSelf-citationMultiphase integrated on-board battery chargers for electrical vehicles
Subotic, I., Levi, E., Jones, M., & Graovac, D. (2013) · 2013 15th European Conference on Power Electronics and Applications (EPE) · doi:10.1109/epe.2013.6631935 · Cited by 19 · cited 1×
“Integrated chargers on the basis of an asymmetrical six-phase [75], a five-phase [76], and a symmetrical six-phase [77] power supply are demonstrated in the literature.”
BackgroundA fast on-board integrated battery charger for four-motor EVs
Subotić, I., Jones, M., & LEVI, E. (2014) · International Conference on Electrical Machines (ICEM) · doi:10.1109/icelmach.2014.6960469 · Cited by 15
Haghbin, S., & Carlson, O. (2014) · The Journal of Engineering · doi:10.1049/joe.2014.0126 · Cited by 14 · cited 1×
“Several solutions employing the same arrangement are presented in the literature [55]–[58].”
MethodXuan, H. V., Lahaye, D. J. P., Polinder, H., & Ferreira, J. A. (2011) · International Conference on Electrical Machines and Systems (ICEMS) · doi:10.1109/icems.2011.6073667 · Cited by 12
Abdel-Khalik, A. S., & Gadoue, S. M. (2011) · Alexandria Engineering Journal · doi:10.1016/j.aej.2010.12.002 · Cited by 12 · cited 1×
“period by exploiting the extra degrees of freedom of multiphase machines [20].”
BackgroundSelf-citationDhulipati, H., Mukundan, S., Li, W., Tjong, J., & Kar, N. C. (2018) · International Conference on Electrical Machines and Systems (ICEMS) · doi:10.23919/icems.2018.8549176 · Cited by 10
Hoseini, S. R. K., Farjah, E., Tashakor, N., & Ghanbari, T. (2015) · Power Electronics, Drive Systems, and Technologies Conference (PEDSTC) · doi:10.1109/pedstc.2015.7093339 · Cited by 9 · cited 1×
“SRMs are cost-effective and high performing, however, they have high torque ripple [14].”
BackgroundPerformance evaluation of a five-phase modular external rotor PM machine with different rotor poles
Abdel-Khalik, A. S., & Ahmed, S. (2012) · Alexandria Engineering Journal · doi:10.1016/j.aej.2012.09.003 · Cited by 8 · cited 1×
“These advantages include high slot fill factor, low cogging torque [81], short end turns, high efficiency, and flux weakening capability [82], [83].”
BackgroundSelf-citationAbdel-Khalik, A. S., Ahmed, S., & Massoud, A. M. (2017) · IEEE GCC Conference and Exhibition (GCCCE) · doi:10.1109/ieeegcc.2017.8448216 · Cited by 8 · cited 2×
“An integrated on-board battery charging system that employs a surface-mounted PM machine with a FSCW arrangement is discussed in [61].”
BackgroundMethodSelf-citationDesign Case Study of A Nine-Phase Integrated On-Board Battery Charger
Metwly, M. Y., Maximos, F. A., Ahmed, A. T., Hawam, A. S., Zaki, A. A.-M., Helal, A. A.-M., Mokhtar, A.-R. M., Abdelghaffar, S., Taha, R. A., Hamdy, R. A., et al. (2018) · International Middle East Power Systems Conference (MEPCON) · doi:10.1109/mepcon.2018.8635134 · Cited by 6 · cited 1×
“However, power transfer capability is typically limited due to several constraints/tradeoffs such as cost, volume, and weight of the vehicle [6].”
BackgroundSelf-citationControl strategy of integrated charger base on split-winding switched reluctance motor drive
Liang, J., Li, W., & Song, Z. (2017) · International Conference on Electrical Machines and Systems (ICEMS) · doi:10.1109/icems.2017.8056378 · Cited by 5 · cited 1×
“Continued interest in SRMs is mainly due to their high starting torque, wide-speed range and fault tolerance capabilities [15].”
BackgroundAbdel-Khalik, A. S. (2012) · Modelling and Simulation in Engineering · doi:10.1155/2012/487203 · Cited by 4 · cited 1×
“These advantages include high slot fill factor, low cogging torque [81], short end turns, high efficiency, and flux weakening capability [82], [83].”
BackgroundSelf-citationHerrera, D., Villegas, J., Galván-Díez, E., & Carrasco, J. M. (2019) · IET Electric Power Applications · doi:10.1049/iet-epa.2018.5338 · Cited by 3 · cited 1×
“Newly added techniques to eliminate torque production during the charging operation on the basis of multiphase machine degrees of freedom have been investigated in [66], [9].”
Background
Research works printed but not linked: 3
- IEA, ''Global EV outlook 2019: Scaling-up the transition to electric mobility,'' OECD, Paris, France, 2019.
- AYMAN S. ABDEL-KHALIK (Senior Member, IEEE) received the B.Sc. and M.Sc. degrees in electrical engineering from Alexandria University, Alexandria, Egypt, in 2001 and 2004, respectively, and the Ph.D. degree in electrical engineering from Alexandria University and Strathclyde University, Glasgow, U.K., in 2009, under a Dual Channel Program. He is currently a Professor with the Department of Electrical Engineering, Faculty of Engineering, Alexandria University. His current research interests include electrical machine design and modeling, electric drives, energy conversion, and renewable energy. He serves as an Associate Editor for the IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS and the IET Electric Power Applications Journal. He also serves as the Executive Editor of the Alexandria Engineering Journal.
- RAGI A. HAMDY (Senior Member, IEEE) received the B.Sc. and M.Sc. degrees from Alexan- dria University, Alexandria, Egypt, in 1991 and 1994, respectively, and the Ph.D. degree from Heriot-Watt University, U.K., in 1999. He is currently a Professor with the Department of Electrical Engineering, Faculty of Engineering, Alexandria University. His current research inter- ests include electric machines, electric drives, and power electronics.
Cited by
Acharige, S. S. G., Haque, M. E., Arif, M. T., Hosseinzadeh, N., Hasan, K. N., & Oo, A. M. T. (2023) · IEEE Access · doi:10.1109/access.2023.3267164 · Cited by 590
A Review of Bidirectional On-Board Chargers for Electric Vehicles
Yuan, J., Dorn-Gomba, L., Callegaro, A. D., Reimers, J., & Emadi, A. (2021) · IEEE Access · doi:10.1109/access.2021.3069448 · Cited by 390
“However, they do not concentrate on the research and application of the bidirectional OBC [1], [13], [25], [26].”
BackgroundKhalid, M. R., Khan, I. A., Hameed, S., Asghar, M. S. J., & Ro, J. (2021) · IEEE Access · doi:10.1109/access.2021.3112189 · Cited by 353
Bidirectional Onboard Chargers for Electric Vehicles: State-of-the-Art and Future Trends
Wouters, H., & Martinez, W. (2024) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2023.3319996 · Cited by 280
“Thisis extensively reviewed in [18], [22], and [54].”
BackgroundRevolution of Electric Vehicle Charging Technologies Accelerated by Wide Bandgap Devices
Li, S., Lu, S., & Mi, C. C. (2021) · Proceedings of the IEEE · doi:10.1109/jproc.2021.3071977 · Cited by 163
“The integrated OBC reuses the existing components of the inverter and the electric motor for the propulsion battery charging circuit, so the cost and weight of the OBCs can be reduced [84].”
Background
Metadata
- Authors
- Metwly, M. Y., Abdel-Majeed, M. S., Abdel-Khalik, A. S., Hamdy, R. A., Hamad, M. S., & Ahmed, S.
- Affiliations
- Arab Academy for Science, Technology, and Maritime Transport (EG)
- Alexandria University (EG)
- King Abdullah University of Science and Technology (SA)
- ORCID
- Venue
- IEEE Access
- Published
- 2020
- Volume
- 8
- Pages
- 85216-85242
- ISSN
- 2169-3536 (ISSN-L)
- OpenAlex
- W3023670470
- Cited by
- 229
- References
- 111
- Citations by year
- 2026: 16 · 2025: 37 · 2024: 59 · 2023: 41 · 2022: 40 · 2021: 28 · 2020: 8
- FWCI
- 10.04
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Locations
- IEEE Access (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- King Abdullah University of Science and Technology Repository (King Abdullah University of Science and Technology) (submittedVersion, cc-by)
- Funders
- ITIDA’s ITAC Collaborative Funded Project through the category type of Preliminary Research Projects (PRP2018.R25.4)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Motor Design and Analysis
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Sensorless Control of Electric Motors
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced DC-DC Converters
- Keywords
- electric vehicles, fractional-slot concentrated winding, permanent magnet motor, induction motor, single-phase charging, bidirectional power flow, motor winding design
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.