The DOI matches its Crossref record; 8 of the 8 references it cites were found in a registry or an index.
Normal and Shear Force Measurement Using a Flexible Polymer Tactile Sensor With Embedded Multiple Capacitors
Abstract
In this paper, we report a new flexible capacitive tactile sensor array with the capability of measuring both normal and shear force distribution using polydimethylsiloxane (PDMS) as a base material. A tactile cell consists of two thick PDMS layers with embedded electrodes, an air gap, and a pillar structure. The pillar structure is formed at the center of each tactile cell between the air gap under a large bump. There are four capacitors in a cell to decompose the contact force into normal and shear components. Four capacitors are arranged in a square form. If a normal force is applied on the bump, the PDMS layer on the pillar structure is compressed, and the air gap between the top and bottom electrodes decreases, resulting in the increase in all four capacitances. If a shear force is applied, a torque is induced around the pillar. Therefore, the capacitance of the two capacitors increases, whereas that of the other two decreases. The bump and the pillar structure play a critical role to generate a torque for shear force measurement. The sensor has been realized in an 8 x 8 array of unit sensors, and each unit sensor responds to normal and shear stresses in all three axes, respectively. Measurement of a single sensor shows that the full-scale range of detectable force is about 10 mN, which corresponds to 131 kPa in three directions. The sensitivities of a cell measured with a current setup are 2.5%/mN, 3.0%/mN, and 2.9 %/mN for the x-, y-, and z-directions, respectively. Normal and shear force images are also captured from a 4 x 4 array of the fabricated sensor. Distinctive characteristic patterns appear when a shear force is applied to the sensor.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Monolithic Microfabricated Valves and Pumps by Multilayer Soft Lithography
Unger, M. A., Chou, H.-P., Thorsen, T., Scherer, A., & Quake, S. R. (2000) · Science · doi:10.1126/science.288.5463.113 · Cited by 4,010
A Flexible Polymer Tactile Sensor: Fabrication and Modular Expandability for Large Area Deployment
Lee, H.-K., Chang, S.-I., & Yoon, E. (2006) · Journal of Microelectromechanical Systems · doi:10.1109/jmems.2006.886021 · Cited by 396
Self-citationHowe, R. D., Peine, W. J., Kantarinis, D. A., & Son, J. S. (1995) · IEEE Engineering in Medicine and Biology Magazine · doi:10.1109/51.391770 · Cited by 296
Development of polyimide flexible tactile sensor skin
Engel, J., Chen, J., & Liu, C. (2003) · Journal of Micromechanics and Microengineering · doi:10.1088/0960-1317/13/3/302 · Cited by 291
A traction stress sensor array for use in high-resolution robotic tactile imaging
Kane, B. J., Cutkosky, M. R., & Kovacs, G. T. A. (2000) · Journal of Microelectromechanical Systems · doi:10.1109/84.896763 · Cited by 235
Silicon three-axial tactile sensor
Chu, Z., Sarro, P. M., & Middelhoek, S. (1996) · Sensors and Actuators A Physical · doi:10.1016/s0924-4247(95)01190-0 · Cited by 150
3-Axes Flexible Tactile Sensor Fabricated by Si Micromachining and Packaging Technology
Kim, K. S., Lee, K. R., Kim, Y. K., Lee, D. S., Cho, N. K., Kim, W. H., Park, K., Park, H. D., Park, Y. K., Kim, J. H., et al. (2006) · IEEE International Conference on Micro Electro Mechanical Systems (MEMS) · doi:10.1109/memsys.2006.1627890 · Cited by 40
A Polymer-Based Flexible Tactile Sensor for Normal and Shear Load Detection
Hwang, E.-S., Seo, J.-H., & Kim, Y.-J. (2006) · IEEE International Conference on Micro Electro Mechanical Systems (MEMS) · doi:10.1109/memsys.2006.1627899 · Cited by 37
Cited by
Hammock, M. L., Chortos, A., Tee, B. C. ‐., Tok, J. B. ‐., & Bao, Z. (2013) · Advanced Materials · doi:10.1002/adma.201302240 · Cited by 2,396
Tactile sensing for dexterous in-hand manipulation in robotics—A review
Yousef, H., Boukallel, M., & Althoefer, K. (2011) · Sensors and Actuators A: Physical · doi:10.1016/j.sna.2011.02.038 · Cited by 784
Tactile sensing in dexterous robot hands — Review
Kappassov, Z., Corrales, J.-A., & Perdereau, V. (2015) · Robotics and Autonomous Systems · doi:10.1016/j.robot.2015.07.015 · Cited by 782
Recent Progress in Materials and Devices toward Printable and Flexible Sensors
Rim, Y. S., Bae, S., Chen, H., De Marco, N., & Yang, Y. (2016) · Advanced Materials · doi:10.1002/adma.201505118 · Cited by 771
A review of tactile sensing technologies with applications in biomedical engineering
Tiwana, M. I., Redmond, S. J., & Lovell, N. H. (2012) · Sensors and Actuators A: Physical · doi:10.1016/j.sna.2012.02.051 · Cited by 721
Metadata
- Authors
- Lee, H.-K., Chung, J., Chang, S.-I., & Yoon, E.
- Venue
- Journal of Microelectromechanical Systems
- Published
- 2008-08
- Volume
- 17
- Issue
- 4
- Pages
- 934-942
- ISSN
- 1057-7157 (ISSN-L)
- 1941-0158
- OpenAlex
- W2103654576
- Cited by
- 350
- References
- 8
- FWCI
- 5.76
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Normal and Shear Force Measurement Using a Flexible Polymer Tactile Sensor With Embedded Multiple Capacitors. https://app.cochat.ai/papers/10.1109/jmems.2008.921727
- The paper
- Lee, H.-K., Chung, J., Chang, S.-I., & Yoon, E. (2008). Normal and Shear Force Measurement Using a Flexible Polymer Tactile Sensor With Embedded Multiple Capacitors. Journal of Microelectromechanical Systems. https://doi.org/10.1109/jmems.2008.921727
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.