Real-Time Model-Based Estimation of SOC and SOH for Energy Storage Systems
The DOI matches its Crossref record; 56 of the 57 references it cites were found in a registry or an index.
Abstract
To obtain a full exploitation of battery potential in energy storage applications, an accurate modeling of electrochemical batteries is needed. In real terms, an accurate knowledge of state of charge (SOC) and state of health (SOH) of the battery pack is needed to allow a precise design of the control algorithms for energy storage systems (ESSs). Initially, a review of effective methods for SOC and SOH assessment has been performed with the aim to analyze pros and cons of standard methods. Then, as the tradeoff between accuracy and complexity of the model is the major concern, a novel technique for SOC and SOH estimation has been proposed. It is based on the development of a battery circuit model and on a procedure for setting the model parameters. Such a procedure performs a real-time comparison between measured and calculated values of the battery voltage while a PI-based observer is used to provide the SOC and SOH actual values. This ensures a good accuracy in a wide range of operating conditions. Moreover, a simple start-up identification process is required based on battery data-sheet exploitation. Because of the low computational burden of the whole algorithm, it can be easily implemented in low-cost control units. An experimental comparison between SOC and SOH estimation performed by suggested and standard methods is able to confirm the consistency of the proposed approach.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Due to its low computational complexity, this model is widely used in SOH estimation [52].”
Citations
Cites
A New Approach to Linear Filtering and Prediction Problems
Kalman, R. E. (1960) · Journal of Basic Engineering · doi:10.1115/1.3662552 · Cited by 31,751
Accurate electrical battery model capable of predicting runtime and I-V performance
Chen, M., & Rincon-Mora, G. A. (2006) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2006.874229 · Cited by 2,427
A comparative study of equivalent circuit models for Li-ion batteries
Hu, X., Li, S., & Peng, H. (2012) · Journal of Power Sources · doi:10.1016/j.jpowsour.2011.10.013 · Cited by 2,179
Experimental Validation of a Battery Dynamic Model for EV Applications
Tremblay, O., & Dessaint, L.-A. (2009) · World Electric Vehicle Journal · doi:10.3390/wevj3020289 · Cited by 1,223
Waag, W., Fleischer, C., & Sauer, D. U. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.02.064 · Cited by 1,059
The State of Charge Estimating Methods for Battery: A Review
Chang, W.-Y. (2013) · ISRN Applied Mathematics · doi:10.1155/2013/953792 · Cited by 650
Huet, F. (1998) · Journal of Power Sources · doi:10.1016/s0378-7753(97)02665-7 · Cited by 593
New dynamical models of lead-acid batteries
Ceraolo, M. (2000) · IEEE Transactions on Power Systems · doi:10.1109/59.898088 · Cited by 584
Design of Primary and Secondary Cells
Shepherd, C. M. (1965) · Journal of The Electrochemical Society · doi:10.1149/1.2423659 · Cited by 510
Bhangu, B. S., Bentley, P., Stone, D. A., & Bingham, C. M. (2005) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2004.842461 · Cited by 507
A New Approach to Linear Filtering and Prediction Problems
(2009) · Control Theory · doi:10.1109/9780470544334.ch9 · Cited by 496
Coleman, M., Lee, C. K., Zhu, C., & Hurley, W. G. (2007) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2007.899926 · Cited by 473
He, H., Xiong, R., Guo, H., & Li, S. (2012) · Energy Conversion and Management · doi:10.1016/j.enconman.2012.04.014 · Cited by 462
Seaman, A., Dao, T.-S., & McPhee, J. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.01.057 · Cited by 453
Doerffel, D., & Sharkh, S. A. (2006) · Journal of Power Sources · doi:10.1016/j.jpowsour.2005.04.030 · Cited by 410
The State of Charge Estimation of Lithium-Ion Batteries Based on a Proportional-Integral Observer
Xu, J., Mi, C. C., Cao, B., Deng, J., Chen, Z., & Li, S. (2014) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2013.2287375 · Cited by 367
Electrical battery model for use in dynamic electric vehicle simulations
Kroeze, R. C., & Krein, P. T. (2008) · 2008 IEEE Power Electronics Specialists Conference · doi:10.1109/pesc.2008.4592119 · Cited by 325
Various battery models for various simulation studies and applications
Mousavi G., S. M., & Nikdel, M. (2014) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2014.01.048 · Cited by 314
Modeling of high power automotive batteries by the use of an automated test system
Schweighofer, B., Raab, K. M., & Brasseur, G. (2003) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2003.814827 · Cited by 306
Gholizadeh, M., & Salmasi, F. R. (2014) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2013.2259779 · Cited by 298
Open circuit voltage characterization of lithium-ion batteries
Pattipati, B., Balasingam, B., Avvari, G. V., Pattipati, K. R., & Bar-Shalom, Y. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.06.152 · Cited by 267
Comparison, Selection, and Parameterization of Electrical Battery Models for Automotive Applications
Einhorn, M., Conte, F. V., Kral, C., & Fleig, J. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2210564 · Cited by 220
Kim, J., Lee, S., & Cho, B. H. (2012) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2011.2158554 · Cited by 207
Tong, S., Klein, M. P., & Park, J. W. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.03.157 · Cited by 206
An Improved Battery Characterization Method Using a Two-Pulse Load Test
Coleman, M., Hurley, W. G., & Lee, C. K. (2008) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2007.914329 · Cited by 191
Hybrid AC–DC Microgrids With Energy Storages and Progressive Energy Flow Tuning
Loh, P. C., Li, D., Chai, Y. K., & Blaabjerg, F. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2210445 · Cited by 175
A Simple, Effective Lead-Acid Battery Modeling Process for Electrical System Component Selection
Jackey, R. A. (2007) · SAE Technical Paper Series · doi:10.4271/2007-01-0778 · Cited by 165
A method for state-of-charge estimation of LiFePO4 batteries based on a dual-circuit state observer
Tang, X., Wang, Y., & Chen, Z. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.07.028 · Cited by 161
Battery modelling methods for electric vehicles - A review
Zhang, C., Li, K., Mcloone, S., & Yang, Z. (2014) · 2014 European Control Conference (ECC) · doi:10.1109/ecc.2014.6862541 · Cited by 158
A PSPICE macromodel for lithium-ion batteries
Gold, S. (2002) · The Twelfth Annual Battery Conference on Applications and Advances · doi:10.1109/bcaa.1997.574106 · Cited by 156
Study of battery modeling using mathematical and circuit oriented approaches
Li, S., & Bao, K. (2011) · IEEE Power Engineering Society General Meeting · doi:10.1109/pes.2011.6039230 · Cited by 151
An overview of generic battery models
Hussein, A. A.-H., & Batarseh, I. (2011) · 2011 IEEE Power and Energy Society General Meeting · doi:10.1109/pes.2011.6039674 · Cited by 145
Discrete-time battery models for system-level low-power design
Luca Benini, C., Castelli, G., Macii, A., Macii, A., Poncino, M., & Scarsi, R. (2001) · IEEE Transactions on Very Large Scale Integration (VLSI) Systems · doi:10.1109/92.953497 · Cited by 136
Accurate battery pack modeling for automotive applications
Li, J., & Mazzola, M. S. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.03.009 · Cited by 114
Sato, S., & Kawamura, A. (2003) · Proceedings of the Power Conversion Conference-Osaka 2002 (Cat. No.02TH8579) · doi:10.1109/pcc.2002.997578 · Cited by 112
Lead acid batteries simulation including experimental validation
Achaibou, N., Haddadi, M., & Malek, A. (2008) · Journal of Power Sources · doi:10.1016/j.jpowsour.2008.06.059 · Cited by 102
On battery State of Charge estimation: A new mixed algorithm
Codeca, F., Savaresi, S. M., & Rizzoni, G. (2008) · 2008 IEEE International Conference on Control Applications · doi:10.1109/cca.2008.4629635 · Cited by 99
Codecà, F., Savaresi, S. M., & Manzoni, V. (2009) · IEEE Conference on Decision and Control (CDC) · doi:10.1109/cdc.2009.5399759 · Cited by 61
A comparative study of lithium ion to lead acid batteries for use in UPS applications
Stan, A.-I., Swierczynski, M. J., Stroe, D., Teodorescu, R., Andreasen, S. J., & Moth, K. (2014) · International Telecommunications Energy Conference (INTELEC) · doi:10.1109/intlec.2014.6972152 · Cited by 60
Kalawoun, J., Biletska, K., Suard, F., & Montaru, M. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.01.038 · Cited by 56
VRLA Battery Discharge Reserve Time Estimation
Pascoe, P. E., & Anbuky, A. H. (2004) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2004.836680 · Cited by 55
The Lead-Acid Battery: Its Voltage in Theory and in Practice
Treptow, R. S. (2002) · Journal of Chemical Education · doi:10.1021/ed079p334 · Cited by 55
Fast Charge Strategy Based on the Characterization and Evaluation of LiFePO $_{\bm 4}$ Batteries
Huang, S., Huang, B.-G., & Pai, F. (2012) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2209184 · Cited by 54
Overview of the types of battery models
Sun, K., & Shu, Q. (2011) · Chinese Control Conference (CCC) · Cited by 51
Impedance modeling of intermediate size lead–acid batteries
Salkind, A. J., Singh, P., Cannone, A. G., Atwater, T. B., Wang, X., & Reisner, D. E. (2003) · Journal of Power Sources · doi:10.1016/s0378-7753(02)00690-0 · Cited by 50
Wang, W., Shu-Hung Chung, H., & Zhang, J. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2300143 · Cited by 47
Kularatna, N. (2014) · IEEE Power Electronics Magazine · doi:10.1109/mpel.2014.2361264 · Cited by 33
Mousavi, S. M., Fathi, S. H., & Riahy, G. H. (2009) · International Conference on Clean Electrical Power · doi:10.1109/iccep.2009.5211989 · Cited by 31
Gould, C. R., Bingham, C. M., Stone, D. A., & Bentley, P. (2008) · International Symposium on Power Electronics, Electrical Drives, Automation and Motion (SPEEDAM) · doi:10.1109/speedham.2008.4581332 · Cited by 26
Third-order dynamic model of a lead acid battery for use in fuel cell vehicle simulation
Wang, H., Li, G., Li, M., Jiang, Z., Wang, X., & Zhao, Q. (2011) · International Conference on Mechatronic Science, Electric Engineering and Computer · doi:10.1109/mec.2011.6025565 · Cited by 17
Evaluation of different methods for measuring the impedance of Lithium-ion batteries during ageing
Stroe, D., Swierczynski, M. J., Stroe, A., Knap, V., Teodorescu, R., & Andreasen, S. J. (2015) · International Conference on Ecological Vehicles and Renewable Energies (EVER) · doi:10.1109/ever.2015.7113024 · Cited by 15
Chen, X., Shen, W., Cao, Z., & Kapoor, A. (2012) · IEEE Conference on Industrial Electronics and Applications (ICIEA) · doi:10.1109/iciea.2012.6360705 · Cited by 13
Gould, C. R., Bingham, C. M., Stone, D. A., & Bentley, P. (2008) · IEEE Power Electronics Specialists Conference (PESC) · doi:10.1109/pesc.2008.4592650 · Cited by 8
SECONDARY BATTERIES – LEAD– ACID SYSTEMS | Modeling
Cugnet, M. G., Dubarry, M., & Liaw, B. Y. (2009) · Elsevier eBooks · doi:10.1016/b978-044452745-5.00151-9 · Cited by 7
Lièvre, A., Pélissier, S., Sarı, A., Venet, P., & Hijazi, A. (2015) · International Conference on Ecological Vehicles and Renewable Energies (EVER) · doi:10.1109/ever.2015.7112986 · Cited by 7
Research works printed but not linked: 5
- waag, 2009, State-of-charge/health, Reference Module in Chemistry Molecular Sciences and Chemical Engineering Encyclopedia of Electrochemical Power Sources, 793
- wenzl, 2009, Self-discharge, Reference Module in Chemistry Molecular Sciences and Chemical Engineering Encyclopedia of Electrochemical Power Sources, 407
- bhangu, 0, Observer techniques for estimating the SOC and SOH of VRLABs for hybrid electric vehicles, Proc 2005 IEEE Veh Power Propulsion Conf, 780
- brando, 0, Comparison of accuracy of different LiFePO4 battery circuital models, Proc 2014 IEEE Power Electron Elect Drives Autom Motion Int Symp, 1092
- 2014, IEEE Recommended Practice for Maintenance, Testing and Replacement of Valve-Regulated Lead-Acid (VRLA) Batteries for Stationary Applications—Amendment 1: Updated VRLA Maintenance Considerations, IEEE Standard 1188a-2014
Cited by
How, D. N. T., Hannan, M. A., Hossain Lipu, M. S., & Ker, P. J. (2019) · IEEE Access · doi:10.1109/access.2019.2942213 · Cited by 812
Zheng, Y., Ouyang, M., Han, X., Lu, L., & Li, J. (2018) · Journal of Power Sources · doi:10.1016/j.jpowsour.2017.11.094 · Cited by 490
Technology Development of Electric Vehicles: A Review
Sun, X., Li, Z., Wang, X., & Li, C. (2019) · Energies · doi:10.3390/en13010090 · Cited by 476
SoC Estimation for Lithium-ion Batteries: Review and Future Challenges
Rivera-Barrera, J., Muñoz-Galeano, N., & Sarmiento-Maldonado, H. (2017) · Electronics · doi:10.3390/electronics6040102 · Cited by 447
Energy Management and Optimization Methods for Grid Energy Storage Systems
Byrne, R. H., Nguyen, T. A., Copp, D. A., Chalamala, B. R., & Gyuk, I. (2018) · IEEE Access · doi:10.1109/access.2017.2741578 · Cited by 406
Metadata
- Authors
- Cacciato, M., Nobile, G., Scarcella, G., & Scelba, G.
- Affiliations
- University of Catania (IT)
- Venue
- IEEE Transactions on Power Electronics
- Published
- 2017-01
- Volume
- 32
- Issue
- 1
- Pages
- 794-803
- ISSN
- 0885-8993 (ISSN-L)
- 1941-0107
- OpenAlex
- W2334417208
- Cited by
- 178
- References
- 57
- Citations by year
- 2026: 18 · 2025: 21 · 2024: 18 · 2023: 12 · 2022: 17 · 2021: 17 · 2020: 27 · 2019: 13 · 2018: 17 · 2017: 17
- FWCI
- 13.94
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- IEEE Transactions on Power Electronics (publishedVersion)
- Funders
- Research Project (PON02_153_2939517)
- Tecnologie ad alta Efficienza per la Sostenibilità Energetica ed ambientale On-board—TESEO
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Control and Systems Engineering › Control Systems and Identification
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Keywords
- state of charge estimation, state of health estimation, battery modeling, energy storage systems, parameter estimation, PI observer, real-time estimation, battery voltage
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.