Frequency Analysis of the Tuned Mass Damper
The DOI matches its Crossref record; 7 of the 7 references it cites were found in a registry or an index.
Abstract
The damping properties of the viscous tuned mass damper are characterized by dynamic amplification analysis as well as identification of the locus of the complex natural frequencies. Optimal damping is identified by a combined analysis of the dynamic amplification of the motion of the structural mass as well as the relative motion of the damper mass. The resulting optimal damper parameter is about 15% higher than the classic value, and results in improved properties for the motion of the damper mass. The free vibration properties are characterized by analyzing the locus of the natural frequencies in the complex plane. It is demonstrated that for optimal frequency tuning the damping ratio of both vibration modes are equal and approximately half the damping ratio of the applied damper, when the damping is below a critical value corresponding to a bifurcation point. This limiting value corresponds to maximum modal damping and serves as an upper limit for damping to be applied in practice.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Citations
Cites
Optimum absorber parameters for various combinations of response and excitation parameters
Warburton, G. B. (1982) · Earthquake Engineering & Structural Dynamics · doi:10.1002/eqe.4290100304 · Cited by 1,043
Passive energy dissipation systems in structural engineering
Crewe, A. (1998) · Structural Safety · doi:10.1016/s0167-4730(97)00034-9 · Cited by 1,015
Passive Energy Dissipation Systems in Structural Engineering
Dargush, G. F., & Soong, T. T. (1997) · Medical Entomology and Zoology · Cited by 880
The Theory of the Dynamic Vibration Absorber
Ormondroyd, J., & Den Hartog, J. P. (1928) · Transactions of the American Society of Mechanical Engineers · doi:10.1115/1.4058553 · Cited by 779
Asami, T., Nishihara, O., & Baz, A. M. (2002) · Journal of Vibration and Acoustics · doi:10.1115/1.1456458 · Cited by 405
A Note on the Damped Vibration Absorber
Brock, J. E. (1946) · Journal of Applied Mechanics · doi:10.1115/1.4009588 · Cited by 356
Richards, K. L. (2017) · CRC Press eBooks · doi:10.1201/9781315367514-9 · Cited by 88
Cited by
Items 101–200 of 241
Tunable electromagnetic resonant shunt using pulse-width modulation
Auleley, M., Giraud-Audine, C., Mahé, H., & Thomas, O. (2021) · Journal of Sound and Vibration · doi:10.1016/j.jsv.2021.116018 · Cited by 21
Modal resonant dynamics of cables with a flexible support: A modulated diffraction problem
Guo, T., Kang, H., Wang, L., Liu, Q., & Zhao, Y. (2018) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2017.12.023 · Cited by 20
Optimal Design of an Inerter-Based Dynamic Vibration Absorber Connected to Ground
Zhou, S., Jean‐Mistral, C., & Chesné, S. (2019) · Journal of vibration and acoustics · doi:10.1115/1.4043945 · Cited by 20
Davidson, J., Kalmár‐Nagy, T., & Habib, G. (2022) · Nonlinear Dynamics · doi:10.1007/s11071-022-07710-1 · Cited by 19
“the DVA stroke) [65], (e) minimizing the total kinetic energy of the primarymass”
BackgroundOptimal design of a pair of vibration suppression devices for a multi‐storey building
Zhang, S. Y., Neild, S. A., & Jiang, J. Z. (2019) · Structural Control and Health Monitoring · doi:10.1002/stc.2498 · Cited by 17
Lin, K., Tan, C. A., Ge, C., & Lu, H. (2021) · International Journal of Structural Stability and Dynamics · doi:10.1142/s0219455422500225 · Cited by 17
Fu, T., Rakheja, S., & Shangguan, W. (2019) · Proceedings of the Institution of Mechanical Engineers Part D Journal of Automobile Engineering · doi:10.1177/0954407019845720 · Cited by 17
Tuned Mass and Parametric Pendulum Dampers Under Seismic Vibrations
Yurchenko, D. (2015) · Springer eBooks · doi:10.1007/978-3-642-36197-5_338-1 · Cited by 17
Damping augmentation of a rotating beam-tendon system via internally placed spring-damper elements
Wu, J. J., & Titurus, B. (2021) · Journal of Sound and Vibration · doi:10.1016/j.jsv.2021.116315 · Cited by 16
The Optimum Inertial Amplifier Tuned Mass Dampers for Nonlinear Dynamic Systems
Chowdhury, S., Banerjee, A., & Adhikari, S. (2022) · International Journal of Applied Mechanics · doi:10.1142/s1758825123500096 · Cited by 16
“The maximum dynamic response of the structure controlled by IATMD has been = Krenk [2005]; Den Hartog and Or-mondroyd [1928]; Nishihara and Asami [2002] determined as 3 .”
InfluentialBaduidana, M., & Kenfack-Jiotsa, A. (2022) · Journal of Vibration Engineering & Technologies · doi:10.1007/s42417-022-00825-0 · Cited by 16
Zhang, Z., Li, X., Larsen, T. G., Sun, T., & Yang, Q. (2024) · Structural Control and Health Monitoring · doi:10.1155/2024/7255774 · Cited by 15
Nonlinear stiffened inertial amplifier tuned mass friction dampers
Chowdhury, S., & Adhikari, S. (2025) · Soil Dynamics and Earthquake Engineering · doi:10.1016/j.soildyn.2025.109264 · Cited by 15
Active Approaches to Vibration Absorption through Antiresonance Assignment: A Comparative Study
Richiedei, D., & Tamellin, I. (2021) · Applied Sciences · doi:10.3390/app11031091 · Cited by 15
Wang, M., Chen, J., Nagarajaiah, S., & Du, X. (2025) · Journal of Building Engineering · doi:10.1016/j.jobe.2025.112203 · Cited by 13
The optimum enhanced viscoelastic tuned mass dampers: Exact closed-form expressions
Chowdhury, S., Banerjee, A., & Adhikari, S. (2023) · Journal of Vibration and Control · doi:10.1177/10775463231156240 · Cited by 14
“The closed-form expressions for optimal design parameters of H ∞ optimized conventional tuned mass damper (i.e., CTMD) are accounted from conventional tuned mass damper ’ s (CTMD) (Den Hartog and Ormondroyd, 1928; Krenk, 2005; Nishihara and Asami, 2002).”
MethodArgentini, T., Belloli, M., & Borghesani, P. (2015) · Journal of vibration and acoustics · doi:10.1115/1.4029576 · Cited by 14
Stewart, G. M., & Lackner, M. A. (2012) · AIAA Aerospace Sciences Meeting · doi:10.2514/6.2012-376 · Cited by 14
Resonant passive–active vibration absorber with integrated force feedback control
Høgsberg, J., Brodersen, M. L., & Krenk, S. (2016) · Smart Materials and Structures · doi:10.1088/0964-1726/25/4/047001 · Cited by 13
“Calibration formulae are presented for two specific configurations: An inertia-based absorber equivalent to a tuned mass or inerter damper [1, 2, 6] and a stiffnessbased absorber similar to that of piezoelectric RL shunt damping [9, 10].”
BackgroundSelf-citationVibration control of a rotating Timoshenko beam-tendon system via internal guiding inerter-dampers
Wu, J. J., & Titurus, B. (2021) · Journal of Sound and Vibration · doi:10.1016/j.jsv.2021.116542 · Cited by 13
A novel concept of floating absorber for motion mitigation in floating offshore wind turbines
Alotta, G., Laface, V., Failla, G., Ruzzo, C., & Arena, F. (2023) · Engineering Structures · doi:10.1016/j.engstruct.2023.116554 · Cited by 13
Baduidana, M., Kendo‐Nouja, B., Kenfack-Jiotsa, A., & Nzengwa, R. (2022) · Asian Journal of Control · doi:10.1002/asjc.2700 · Cited by 13
“Therefore, based on Krenk [23], Barredo et al.”
MethodInfluentialGao, J., Zhang, X., & Yu, X. (2024) · SAE International journal of vehicle dynamics, stability, and NVH · doi:10.4271/10-08-02-0014 · Cited by 12
Floor Vibration Control as a Serviceability Requirement in Design Standards and Practices: Review
Jaafari, C., & Mohammadi, J. (2018) · Practice Periodical on Structural Design and Construction · doi:10.1061/(asce)sc.1943-5576.0000361 · Cited by 12
Agostoni, S., Cheli, F., Leo, E., & Pezzola, M. (2012) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2011.11.018 · Cited by 12
Experimental observation of exceptional points in coupled pendulums
Even, N., Nennig, B., Lefebvre, G., & Perrey‐Debain, E. (2024) · Journal of Sound and Vibration · doi:10.1016/j.jsv.2024.118239 · Cited by 11
“In this regard, one can cite [12] or [11] where it is shown that the double root condition represents an upper limit for the damper.”
BackgroundMethodInfluentialJin, S., Tan, C. A., & Lu, H. (2024) · Engineering Structures · doi:10.1016/j.engstruct.2024.117649 · Cited by 11
Optimization of structural design with pendulum dynamic vibration absorber using genetic algorithm
Lee, H. M., Han, S. J., Kim, D., & Yoon, G. H. (2022) · Journal of Vibration and Control · doi:10.1177/10775463221090325 · Cited by 10
“Though increase in responses at neutral frequency ranges not responsible for structural instability can be induced, the application of dynamic vibration absorbers results in the achievement of overall structural stability (Krenk 2005).”
BackgroundMulti-resonant TVA formed by a tree of deflated composite beams with core structured fabrics
Gardonio, P., Ortis, L., Rustighi, E., Malacarne, C., & Perini, M. (2024) · Smart Materials and Structures · doi:10.1088/1361-665x/ad9c07 · Cited by 10
Optimal tuned outrigger-ATMD systems considering seismic and wind loads
Xing, L., Zhou, Y. M., & Zhang, P. (2023) · Soil Dynamics and Earthquake Engineering · doi:10.1016/j.soildyn.2023.108023 · Cited by 10
Revannasiddaiah, T., & Kumar, R. (2013) · Illinois Digital Environment for Access to Learning and Scholarship (University of Illinois at Urbana-Champaign) · Cited by 10
Marian, L. (2015) · City Research Online (City University London) · Cited by 10
Ümütlü, R. C., Bıdıklı, B., Öztürk, H., & Pavić, A. (2023) · Journal of Vibration and Control · doi:10.1177/10775463231166734 · Cited by 9
“Calculations for optimal TMD are taken from Krenk (2005).”
BackgroundArgentini, T., Belloli, M., Robustelli, F. C., Martegani, L., & Fraternale, G. (2013) · ASME International Mechanical Engineering Congress and Exposition (IMECE) · doi:10.1115/imece2013-64425 · Cited by 9
Zhou, S., & Bao, B. (2024) · Journal of Sound and Vibration · doi:10.1016/j.jsv.2024.118777 · Cited by 8
Sonkusare, V. D., & Bera, K. K. (2025) · Engineering Structures · doi:10.1016/j.engstruct.2025.119954 · Cited by 8
On the inclusion of structural loading and damping in piezoelectric shunt tuning
Toftekær, J. F., & Høgsberg, J. (2021) · Journal of Sound and Vibration · doi:10.1016/j.jsv.2021.115960 · Cited by 8
“In the present case, the objective is based on the balanced calibration principle [37], that yields a flat absorber response, which for piezoelectric LR-shunt damping corresponds to a flat voltage response [29].”
BackgroundInfluentialIdentification of beneficial mass-included inerter-based vibration suppression configurations
Li, Y., Zhang, S. Y., Jiang, J. Z., & Neild, S. A. (2019) · Journal of the Franklin Institute · doi:10.1016/j.jfranklin.2019.04.011 · Cited by 8
“The tuned mass damper (TMD), proposed by Frahm [1], is a widely employed passive absorbers consisting of mass, spring and damper elements [2, 3].”
BackgroundCut-out resonators for tuned vibration suppression of plates
Yeh, S.-L., & Harne, R. L. (2021) · Thin-Walled Structures · doi:10.1016/j.tws.2021.108200 · Cited by 8
Semi-Active Vibration Control of Aircraft Structures
Chatziathanasiou, G. M., Chrysohoidis, N., Kostas, G., & Saravanos, D. A. (2021) · AIAA SciTech Forum · doi:10.2514/6.2021-1736 · Cited by 7
Symmetric and asymmetric periodic motions of a nonlinear oscillator with a tuned mass damper inerter
Guo, C., & Luo, A. C. J. (2021) · The European Physical Journal Special Topics · doi:10.1140/epjs/s11734-021-00235-5 · Cited by 7
Liu, Y., & Li, C. (2024) · Applied Mathematical Modelling · doi:10.1016/j.apm.2024.115812 · Cited by 7
Hoffmeyer, D., & Høgsberg, J. (2020) · Journal of vibration and acoustics · doi:10.1115/1.4046752 · Cited by 7
“Specifically for tuned mass absorbers this principle also implies equal damping of the two modes associated with the selected vibration form of the structure [7].”
BackgroundInfluentialDesign of a Resonator-Based Metamaterial for Broadband Control of Transverse Cable Vibration
Singleton, L., Cheer, J., & Daley, S. (2019) · ePrints Soton (University of Southampton) · doi:10.18154/rwth-conv-239432 · Cited by 7
Pisano, M., Turco, E., Petrone, G., Gardonio, P., & Rosa, S. D. (2023) · Journal of Sound and Vibration · doi:10.1016/j.jsv.2023.117827 · Cited by 6
Viet, L. D. (2012) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/0954406212437302 · Cited by 6
Observer-Based Delayed Resonator with Acceleration Feedback
Koçak, S., & Ergenç, A. F. (2018) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2018.07.197 · Cited by 6
Conception et optimisation d'amortisseurs à masse accordée pour les structures du génie civil
Allani, A. (2015) · theses.fr (ABES) · doi:10.70675/50e41dd6z4203z4b4aza20fzd106854b8cf6 · Cited by 6
“Nous allons également utiliser, dans le cas d’un seul AMA, les critères empiriques tels que ceux utilisés dans les méthodes de Den Hartog [68], Krenk [112] et Fujino [105].”
BackgroundXue, J. H., Ma, H., & Chen, L. (2024) · Acta Mechanica Sinica · doi:10.1007/s10409-024-24141-x · Cited by 5
Bidirectional vibration control for FOWTs using tuned cable-inerter systems
Chen, M., Li, S., Wang, R., Sun, Y., & Zhao, Y. (2026) · International Journal of Mechanical Sciences · doi:10.1016/j.ijmecsci.2026.111275 · Cited by 5
Vortex-induced vibration control of bridges using a nonlinear energy sink: A CFD-based study
Li, B., & Zhang, M. (2026) · Journal of Wind Engineering and Industrial Aerodynamics · doi:10.1016/j.jweia.2026.106438 · Cited by 5
Structural vibration control using nonlinear damping amplifier friction vibration absorbers
Chowdhury, S., & Adhikari, S. (2025) · Applied Mathematics and Mechanics · doi:10.1007/s10483-025-3248-7 · Cited by 5
“[30] The additional tests are intended to validate the proposed methodology in a wider variety of seismic excitation conditions.”
Advanced Energy Harvesting Vibration Absorbers Using Inertial Amplifiers
Chowdhury, S., Adhikari, S., & Banerjee, A. (2025) · ASCE-ASME Journal of Risk and Uncertainty in Engineering Systems Part A Civil Engineering · doi:10.1061/ajrua6.rueng-1529 · Cited by 5
Optimization of Viscoelastic Tuned Mass Damper Systems Subjected to Coloured Excitations
Argenziano, M., Palmeri, A., Carotenuto, A. R., Mele, E., & Fraldi, M. (2025) · Earthquake Engineering & Structural Dynamics · doi:10.1002/eqe.70025 · Cited by 5
“While many studies assume zero damping in primary systems of TMD-controlled structures [13, 17, 47, 48, 52], real-world civil engineering structures always exhibit some level of damping.”
Optimal Design of Maxwell-Viscous Coulomb Air Damper With a Modified Fixed Point Theory
Wong, W. O., & Wong, C. N. (2020) · Journal of vibration and acoustics · doi:10.1115/1.4048388 · Cited by 5
Localized Energy Absorbers in Hertzian Chains
Vasconcellos, C., Zuñiga, R., Job, S., & Melo, F. S. M. (2022) · Physical Review Applied · doi:10.1103/physrevapplied.18.014078 · Cited by 5
OPTIMUM DESIGN PROCESS OF VIBRATION ABSORBER VIA IMPERIALIST COMPETITIVE ALGORITHM
Hoseini, R., & SALEHIPOOR, H. (2012) · International Journal of Structural Stability and Dynamics · doi:10.1142/s0219455412500198 · Cited by 5
Wind Turbine Rotors with Active Vibration Control
Svendsen, M. N. (2011) · Cited by 5
Optimization of passive cantilever-type tuned mass damper to reduce the hand postural tremor
Gebai, S. (2020) · theses.fr (ABES) · doi:10.70675/994e0848ze136z4e48z8db8z9981215dcb5b · Cited by 5
Xu, K., Li, M., Ma, R., Han, Q., & Du, X. (2025) · Earthquake Engineering & Structural Dynamics · doi:10.1002/eqe.70001 · Cited by 4
“The root locus diagram is widely used to assess performance, providing insights into both damping enhancement and energy dissipation capacity [56–58].”
Tuning of a Viscous Inerter Damper: How to Achieve Resonant Damping Without a Damper Resonance
Høgsberg, J. (2025) · Applied Sciences · doi:10.3390/app15020676 · Cited by 4
Wu, J. J., & Titurus, B. (2025) · Journal of the Franklin Institute · doi:10.1016/j.jfranklin.2025.107567 · Cited by 4
Huang, Z.-H., Wang, J., Zhang, D., & Wang, X. (2025) · International Journal of Non-Linear Mechanics · doi:10.1016/j.ijnonlinmec.2025.105219 · Cited by 4
An adaptive tuned mass damper based on shape memory alloys with an extended range of frequency
Berardengo, M., Cigada, A., Guanziroli, F., & Manzoni, S. (2014) · IEEE Workshop on Environmental, Energy, and Structural Monitoring Systems (EESMS) · doi:10.1109/eesms.2014.6923272 · Cited by 4
“In both the regions a proportional integral control was used and the current I provided to the SMA wires was calculated as: I(t)=I0+kp•z(t)+ki •∫z(t)dt [9] Where I0 is a constant current , whose value depends on the region the controller is working in.”
BackgroundMethodTurco, E., Gardonio, P., & Bo, L. D. (2021) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/0954406221991182 · Cited by 4
“It is important to observe that the time-averaged vibration power absorbed by the shunted electromagnetic vibration absorber given in equation (16) corresponds to the sum of the time-averaged mechanical and electrical powers dissipated within the transducer and coil and shunt components given in equations (17) and (18…”
BackgroundGuo, C., & Luo, A. C. J. (2022) · International Journal of Dynamics and Control · doi:10.1007/s40435-022-00914-8 · Cited by 4
“In 2005, Krenk [4] studied the damping of a tuned mass damper through dynamic amplification analysis.”
Tuned Mass and Parametric Pendulum Dampers Under Seismic Vibrations
Yurchenko, D. (2015) · Springer eBooks · doi:10.1007/978-3-642-35344-4_338 · Cited by 4
Zhang, H., & Chen, M. Z. Q. (2024) · IET Control Theory and Applications · doi:10.1049/cth2.12702 · Cited by 3
Dynamic properties of a building with viscous dampers in non-proportional arrangement
Suárez, L. E., & Gaviria, C. A. (2015) · STRUCTURAL ENGINEERING AND MECHANICS · doi:10.12989/sem.2015.55.6.1241 · Cited by 3
Hong, D., Ahn, C.-W., Shim, J.-J., Lee, S., & Jung, Y.-D. (2015) · International Journal of Precision Engineering and Manufacturing · doi:10.1007/s12541-015-0209-8 · Cited by 3
“These models are made according to the mass variation of an inertia ring considering case mass.(4) Prototype model is similar to commercial product.”
MethodHigher-Order Complex Periodic Motions in a Nonlinear, Electromagnetically Tuned Mass Damper System
Guo, C., & Luo, A. C. J. (2022) · International Journal of Bifurcation and Chaos · doi:10.1142/s0218127422501693 · Cited by 3
Resonant Damping of Flexible Structures Under Random Excitation
Krenk, S., & Høgsberg, J. (2010) · Computational methods in applied sciences · doi:10.1007/978-90-481-9987-7_2 · Cited by 3
“S. Krenk ( ) and J. Høgsberg Department of Mechanical Engineering, Technical University of Denmark, Nils Koppels Allé, Building 403, DK-2800 Kgs. Lyngby, Denmark e-mail: sk@mek.dtu.dk; jhg@mek.dtu.dk M. Papadrakakis et al. (eds.)”
BackgroundMethodSelf-citationRahman, M. L. H. A., & Hudha, K. (2015) · Asian Control Conference (ASCC) · doi:10.1109/ascc.2015.7244474 · Cited by 3
“This is due to the fact that fatigue life of the damper depends dominantly on the suspension travel magnitude at medium and high frequency vibration [36].”
BackgroundExperimental Analysis of a Tuned Mass Damper with Eddy Currents Damping Effect
Feudo, S. L., Allani, A., Cumunel, G., Argoul, P., Maceri, F., & Bruno, D. (2017) · Springer series in solid and structural mechanics · doi:10.1007/978-3-319-48884-4_13 · Cited by 3
Analytical Method for Designing the Tuned Mass Damper Based on the Complex Stiffness Theory
Kordi, F., & Alamatian, J. (2019) · Iranian Journal of Science and Technology Transactions of Civil Engineering · doi:10.1007/s40996-018-0222-0 · Cited by 3
“(1985) k 2 = k 1 (1 + ) 2 = √ (1 + ) RD Minimization of displacement of the main mass and relative displacement Krenk (2005) k 2 = k 1 (1 + ) 2 = √ 2(1 + ) KE Minimizing the total kinetic energy of the primary mass over all frequencies Warburton (1982) k 2 = k 1 1 + = √ 2 1 3 approaches.”
BackgroundShip roll control and energy harvesting using a U- tube anti-roll tank
Alujević, N., Ćatipović, I., Malenica, Š., Senjanović, I., & Vladimir, N. (2018) · Cited by 3
A DVA-Beam Element for Dynamic Simulation of DVA-Beam System: Modeling, Validation and Application
Song, J., Si, P., Hua, H., & Li, Z. (2022) · Symmetry · doi:10.3390/sym14081608 · Cited by 3
Yasin, S. M., Zaheeruddin, M., Mukarram, S. S., & Raju, E. M. (2023) · Advances in engineering research/Advances in Engineering Research · doi:10.2991/978-94-6463-252-1_105 · Cited by 2
Low-order coupled model for vortex-induced vibrations mitigation by resonant piezoelectric shunt
Haudeville, A., Amandolèse, X., Lossouarn, B., Giraud-Audine, C., & Thomas, O. (2025) · Journal of Fluids and Structures · doi:10.1016/j.jfluidstructs.2025.104442 · Cited by 2
Optimal Tuning of Inerter–Spring–Damper Vehicle Suspension for Mitigation of Bridge Response
Zhang, B., Xu, Y., & Tan, C. A. (2024) · International Journal of Structural Stability and Dynamics · doi:10.1142/s0219455425502396 · Cited by 2
Optimum Tuning of Tuned Mass Dampers for Acceleration Control of Damped Structures
Nguyen, H. A. T. (2021) · Lecture notes in mechanical engineering · doi:10.1007/978-981-16-3239-6_42 · Cited by 2
Maślanka, M. (2023) · Applied Sciences · doi:10.3390/app132111645 · Cited by 2
Piezoelectric RL shunt damping of flexible structures
Høgsberg, J., & Krenk, S. (2015) · Cited by 2
Self-citationAbsorbedor dinámico de vibración no tradicional para controlar fuerza inercial
Mendoza-Larios, J. G., Barredo, E., & Maldonado-Bravo, I. A. (2022) · Cultura Científica y Tecnológica · doi:10.20983/culcyt.2022.2.2.1 · Cited by 2
Cubic root-locus format for structures with a local viscous damping device
Krenk, S. (2023) · Journal of Sound and Vibration · doi:10.1016/j.jsv.2023.117577 · Cited by 1
Self-citationLi, J., Qiao, X., Cheng, Z., & Shi, Z. (2024) · Urban Lifeline · doi:10.1007/s44285-024-00024-1 · Cited by 1
Analytical optimization of transient response for inerter-based vibration systems
Hua, T., & Chen, M. Z. Q. (2025) · Journal of Vibration Engineering & Technologies · doi:10.1007/s42417-025-01778-w · Cited by 1
“To examine the transient response of vibration systems, equal modal damping-based optimal design is first adopted for traditional TMD [29].”
Ding, H., Zhu, A., & Zhang, Z. (2025) · Earthquake Engineering and Resilience · doi:10.1002/eer2.70026 · Cited by 1
Efficient Vibration Control of Optimized Cable Rotating Mass System Using Low Damping Coefficient
Cao, M., & Zhang, R. (2026) · Journal of Vibration Engineering & Technologies · doi:10.1007/s42417-025-02230-9 · Cited by 1
“Then, by applying method proposed by Krenk [46], three invariant frequencies β IF1 , β IF2 and β IF3 are yielded from two characteristic equations when the damping ratio is zero and closed to infinity In this case, the minimum H ( H min ) appears exactly at the 3 invariant frequencies, and the…”
In-sample versus ensemble optimisation of tuned mass dampers for structures with uncertainties
Chowdhury, S., & Adhikari, S. (2026) · Probabilistic Engineering Mechanics · doi:10.1016/j.probengmech.2026.103982 · Cited by 1
Hay, G., Giraud-Audine, C., Mahé, H., & Thomas, O. (2026) · Journal of Sound and Vibration · doi:10.1016/j.jsv.2026.120067 · Cited by 1
Dynamic Absorbers for Rotating Machinery
Borghesani, P., Argentini, T., Belloli, M., & Robustelli, F. C. (2015) · Mechanisms and machine science · doi:10.1007/978-3-319-06590-8_140 · Cited by 1
Damping of coupled bending-torsion beam vibrations by a two-dof tmd with analogous coupling
Høgsberg, J. (2021) · Structural Dynamics · doi:10.25518/2684-6500.56 · Cited by 1
Autonomous Hybrid Semi-Active Tuned Mass Damper for Vibration Control of Aircraft Structures
Chatziathanasiou, G. M., Chrysochoidis, N. A., & Saravanos, D. A. (2022) · AIAA SciTech Forum · doi:10.2514/6.2022-1342 · Cited by 1
Modal interactions in the vicinity of exceptional points and application to acoustic attenuation
Even, N. (2024) · theses.fr (ABES) · doi:10.70675/6581765az0238z4573z9b24z17301723a108 · Cited by 1
Vibration Control of Bridge Using Multiple Tuned Mass Dampers
Lee, Y., Park, Y.-J., Park, I., Kwon, H., & Park, J. (2014) · Korean Society of Hazard Mitigation · doi:10.9798/kosham.2014.14.3.83
“TMD를 결합한 시스템의 기존 질량(m 0 , 구조물)의 변위는 식 (1)과 같이 표현될 수 있다(Steen Krenk 2005).”
Vibration Assessment of Adelaide's new Riverbank Foot-Bridge
Mackenzie, N., & Lee, Y.-K. (2013)
Modeling and Control of Joint-Actuated Buoys
Cortesi, R. S. (2012) · PhDT
Optimization of a tuned vibration absorber in a multibody system by operational analysis
Infante, F., Perfetto, S., Mayer, D., & Herold, S. (2016) · Journal of Physics Conference Series · doi:10.1088/1742-6596/744/1/012111
Active strategies with TMDs for control of wind turbine vibrations
Fitzgerald, B. (2012) · Arrow@dit (Dublin Institute of Technology)
Metadata
- Authors
- Krenk, S.
- Affiliations
- Technical University of Denmark (DK)
- Corresponding author
- Krenk, Steen
- ORCID
- Krenk, Steen
- Venue
- Journal of Applied Mechanics
- Publisher
- ASME International
- Published
- 2005-05-15
- Volume
- 72
- Issue
- 6
- Pages
- 936-942
- ISSN
- 0021-8936 (ISSN-L)
- 1528-9036
- OpenAlex
- W1968064524
- Cited by
- 217
- References
- 7
- Citations by year
- 2026: 16 · 2025: 17 · 2024: 16 · 2023: 17 · 2022: 23 · 2021: 25 · 2020: 14 · 2019: 14 · 2018: 8 · 2017: 7 · 2016: 10 · 2015: 11 · 2014: 9 · 2013: 10 · 2012: 10
- FWCI
- 4.65
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Journal of Applied Mechanics (publishedVersion)
- Technical University of Denmark, DTU Orbit (Technical University of Denmark, DTU) (submittedVersion)
- Topics
- Physical Sciences › Engineering › Civil and Structural Engineering › Vibration Control and Rheological Fluids
- Physical Sciences › Engineering › Mechanical Engineering › Vibration and Dynamic Analysis
- Physical Sciences › Engineering › Civil and Structural Engineering › Structural Engineering and Vibration Analysis
- Keywords
- tuned mass damper, viscous damping, optimal damping, dynamic amplification, complex natural frequencies, frequency tuning, bifurcation, modal damping, structural vibration control
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.