Prediction of Mechanical Efficiency of Parallel-Axis Gear Pairs
The DOI matches its Crossref record; 35 of the 40 references it cites were found in a registry or an index.
Abstract
A computational model is proposed for the prediction of friction-related mechanical efficiency losses of parallel-axis gear pairs. The model incorporates a gear load distribution model, a friction model, and a mechanical efficiency formulation to predict the instantaneous mechanical efficiency of a gear pair under typical operating, surface, and lubrication conditions. The friction model uses a new friction coefficient formula obtained by using a validated non-Newtonian thermal elastohydrodynamic lubrication (EHL) model in conjunction with a multiple linear regression analysis. The load and friction coefficient distribution predictions are used to compute instantaneous torque/power losses and the mechanical efficiency of a gear pair at any given rotational position. Efficiency measurements from gear pairs having various gear designs and surface treatments are compared to model predictions. Mechanical efficiency predictions are shown to be within 0.1% of the measured values, indicating that the proposed efficiency model is accurate. Results of a parametric study are presented at the end to highlight the influence of key basic gear geometric parameters, tooth modifications, operating conditions, surface finish, and lubricant properties on mechanical efficiency losses.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Citations
Cites
Gear Geometry and Applied Theory
Litvin, F. L., & Fuentes, A. (2004) · Cambridge University Press eBooks · doi:10.1017/cbo9780511547126 · Cited by 2,332
Elasto-Hydrodynamic Lubrication
(1977) · Elsevier eBooks · doi:10.1016/c2013-0-05764-7 · Cited by 591
Applied Tribology: Bearing Design and Lubrication
Kennedy, F. E. (2002) · Journal of Tribology · doi:10.1115/1.1432665 · Cited by 325
Handbook of Practical Gear Design
Dudley, D. W. (1984) · Medical Entomology and Zoology · Cited by 286
Applied Tribology: Bearing Design and Lubrication
Khonsari, M. M., & Booser, E. R. (2017) · Wiley eBooks · doi:10.1002/9781118700280 · Cited by 235
Instantaneous Coefficients of Gear Tooth Friction
Benedict, G. H., & Kelley, B. W. (1961) · A S L E Transactions · doi:10.1080/05698196108972420 · Cited by 201
Fourth Paper: Shear Behaviour of Elastohydrodynamic Oil Films at High Rolling Contact Pressures
Johnson, K. L., & Cameron, R. (1967) · Proceedings of the Institution of Mechanical Engineers · doi:10.1243/pime_proc_1967_182_029_02 · Cited by 162
Development of a generalized mechanical efficiency prediction methodology for gear pairs
Xu, H. J. (2005) · OhioLink ETD Center (Ohio Library and Information Network) · Cited by 161
Self-citationChittenden, R. J., Dowson, D., Dunn, J. F., & Taylor, C. M. (1985) · Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences · doi:10.1098/rspa.1985.0015 · Cited by 155
Conry, T. F., & Seireg, A. (1973) · Journal of Engineering for Industry · doi:10.1115/1.3438259 · Cited by 145
Research works printed but not linked: 7
- Reuleaux, Friction in Tooth Gearing, Trans. ASME, VIII, 45
- Kelley, Lubrication of Involute Gearing, Proc. Inst. Mech. Eng., 182, 173
- Dowson, A Theory of Involute Gear Lubrication, 8
- Simon, V. , 1981, “Load Capacity and Efficiency of Spur Ears in Regard to Thermo-End Lubrication,” International Symposium on Gearing and Power Transmissions, Tokyo, Japan.
- Mihalidis, A., Bakolas, V., Panagiotidis, K., and Drivakos, N., 2002, “Prediction of the Friction Coefficient of Spur Gear Pairs,” VDI-Berichte, NR. 1665, pp. 705–719.
- Chittenden, A Theoretical Analysis of The Isothermal Elastohydrodynamic Lubricant of Concentrated Contacts, Proc. R. Soc. London, Ser. A, 397, 271
- Johnson, Shear Behavior of Elastohydrodynamic Oil Films at High Rolling Contact Pressures, Proc. Inst. Mech. Eng., 182, 307
Cited by
Items 201–300 of 320
Wang, L., Zhao, N., An, X., & Li, J. (2025) · The Journal of Supercomputing · doi:10.1007/s11227-025-07367-8 · Cited by 4
A novel forward performance-driven design method for gear parameters
Zheng, J., Liu, C., Chen, S., et al. (2024) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/09544062241271620 · Cited by 3
“In this paper, the formula for calculating the friction coefficient m proposed by Xu et al. 26 is shown in equation (35): where h 0 is the dynamic viscosity of lubricating oil; S is the root mean square of surface roughness; R is the equivalent curvature radius of gear 1 and 2 at the contact point;…”
Xu, J., Hou, Y., Tao, Y., et al. (2025) · Ocean Engineering · doi:10.1016/j.oceaneng.2025.120556 · Cited by 3
Wang, C. (2021) · Mechanics & Industry · doi:10.1051/meca/2021025 · Cited by 3
A New Calculation Method for Instantaneous Efficiency and Torque Fluctuation of Spur Gears
Tian, X., Wang, G., & Jiang, Y. (2024) · Strojniški vestnik – Journal of Mechanical Engineering · doi:10.5545/sv-jme.2023.709 · Cited by 3
Sanoussi, N. S., Hammami, M., Féki, N., Belgasam, T. M., Abbès, M. S., & Haddar, M. (2024) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/13506501231223073 · Cited by 4
Li, Y., & Dong, L. (2025) · Journal of the Brazilian Society of Mechanical Sciences and Engineering · doi:10.1007/s40430-025-05680-0 · Cited by 5
“The expression of the friction coefficient calculation model based on the EHL theory proposed by Xu is [36]: where P c is the central oil film pressure.”
InfluentialRavivarman, R., & Sekar, R. P. (2020) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/1350650120945533 · Cited by 3
Influence of PAO + ester oil formulations on gear micropitting and efficiency
Martins, R. C., Seabra, J., & Moron, L. F. (2011) · International Journal of Surface Science and Engineering · doi:10.1504/ijsurfse.2011.044280 · Cited by 3
“Several authors (Xu et al., 2007; Höhn et al., 1996; Benedict and Kelly, 1960; ISO, 2000; Diab et al., 2006) propose formulas for friction coefficient between gear tooth.”
BackgroundInfluence of Traction Oil on Power Loss of Cylindrical Gears
MORIKAWA, K., Nagahara, M., Nishihara, R., et al. (2013) · TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series C · doi:10.1299/kikaic.79.2609 · Cited by 3
Dykas, B., Stringer, D. B., & LaBerge, K. E. (2012) · Cited by 3
Diagnosing Lubricant Shortages in Gearboxes Using Instantaneous Phases from Electrical Signals
Hamad, N., Sun, X., Zhang, R., et al. (2018) · International Conference on Automation and Computing (ICAC) · doi:10.23919/iconac.2018.8748999 · Cited by 3
“where vo is the dynamic viscosity, and other motion, load and geometry related parameters are depicted in [28].”
BackgroundDynamic responses and control of geared transmission system based on multibody modeling methodology
Yao, Z., Wang, J., & Zhao, Y. (2022) · Journal of Vibration and Control · doi:10.1177/10775463211049584 · Cited by 3
“According to validated non-Newtonian and EHL theory, a friction coefficient calculation method was proposed by Xu et al. (2007), considering slide-to-roll ratio, unit normal load, lubricant viscosity, and gear surface roughness.”
MethodLiu, L., & Ni, J. (2022) · Mechanics & Industry · doi:10.1051/meca/2022009 · Cited by 3
Theoretical transmission analysis to optimize Gearbox for a 2.6 kW automatic pepper transplanter
Islam, M. N., Iqbal, M. Z., Ali, M., Chowdhury, M., Kiraga, S., Kabir, M. S. N., Lee, D.-H., Woo, J.-K., & Chung, S. (2022) · Journal of Agricultural Engineering · doi:10.4081/jae.2022.1254 · Cited by 3
Performance enhancement of normal contact ratio gearing system through correction factor
Ravivarman, R., Palaniradja, K., & Sekar, R. P. (2019) · JOURNAL OF MECHANICAL ENGINEERING AND SCIENCES · doi:10.15282/jmes.13.3.2019.03.0429 · Cited by 3
“al [15] in its model which included both the above mentioned components in their study.”
BackgroundMethodInfluentialAn Approach to Multicriteria Optimization of the Three-Stage Planetary Gear Train
Stefanović-Marinović, J., Perić, M., Miltenović, A., et al. (2025) · Machines · doi:10.3390/machines13110978 · Cited by 2
Collaborative optimization of electromechanical control parameters in electric drive systems
Li, Z., Wu, X., Liu, C., et al. (2025) · International Journal of Electrical Power & Energy Systems · doi:10.1016/j.ijepes.2025.111321 · Cited by 2
Meshing Efficiency of Involute Helical Gears Based on Elastohydrodynamic Lubrication
Wang, B., & Chen, X. B. (2014) · Applied Mechanics and Materials · doi:10.4028/www.scientific.net/amm.597.450 · Cited by 2
“Introduction The power lose caused by the friction of gear pairs inevitably converted into heat, which has an important influence on the failure of transmission performance and the design of lubrication system [1].”
BackgroundDemand Analysis of Lubricating Oil in Spur Gear Pairs
Jia, F., Lei, Y., Fu, Y., et al. (2020) · Applied Sciences · doi:10.3390/app10165417 · Cited by 2
“Tooth surfaces are completely separated by the lubricating oil film in EHL, and the friction coefficient between two teeth can be written as [25]”
BackgroundGonzãlez-Perez, I., & Fuentes, A. (2023) · Forschung im Ingenieurwesen · doi:10.1007/s10010-023-00707-1 · Cited by 3
“To this end, in [5], a computational model is proposed as a combination of a load distribution model, a friction model based on an elasto-hydrodynamic behavior and a mechanical efficiency formulation.”
MethodAnalysis of the dynamic characteristics of the gear-shifting process under external excitation
Zhang, W., Song, Q., Lai, W., et al. (2023) · Advances in Mechanical Engineering · doi:10.1177/16878132231216627 · Cited by 2
“The non-Newtonian thermoelastic lubrication theory was applied by Xu et al. 17,18 to predict the friction coefficient distribution of all contact points in gear meshing, and a formula for variable friction coefficient was derived.”
MethodLiu, L., Kong, R., & Chen, Z. (2024) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/13506501241238280 · Cited by 6
“29 Given that EHL analyses cost computational time, this study adopts Xu ’ s formula 20 to estimate the friction coef fi cient in EHL fl uid fi lm conditions.”
MethodPower flow and efficiency analysis of 2K-V gear transmission via virtual power
Zhu, F., Song, C., Bonaiti, L., & Gorla, C. (2024) · Meccanica · doi:10.1007/s11012-023-01743-5 · Cited by 2
Zhang, X., Li, H. W., Li, Q., et al. (2024) · Mechanics of Solids · doi:10.1134/s0025654423602392 · Cited by 2
“[32–33] ) v e, c, )log(29700 /( ( ) ( ))), i i f t t η M ( ( ), ( ), , ) ( ) ( )log i S t t t t is the comprehensive curvature radius, and R i ( t ) = + R i , 2 ( t )); is the curvature radius of gear tooth profile, and R i , g ( t ) = ; is the average tooth surface roughness; ) ) ) ) r i is the…”
Mo, S., Zhang, Y., Chen, K., et al. (2025) · Journal of Vibration Engineering & Technologies · doi:10.1007/s42417-024-01740-2 · Cited by 2
Gear with Asymmetric Teeth for use in Wind Turbines
Ekwaro-Osire, S., Jang, T.-J., Stroud, A., et al. (2011) · Conference proceedings of the Society for Experimental Mechanics · doi:10.1007/978-1-4419-9798-2_9 · Cited by 2
“The predictions from the model were shown to be within 0.1% of the measured values [ 24 ].”
ResultInfluentialPhraeknanthoe, J., Ponchai, N., & Ratanasumawong, C. (2014) · Applied Mechanics and Materials · doi:10.4028/www.scientific.net/amm.619.68 · Cited by 2
Guyonneau, D., Mermoz, E., Mailhé, J., et al. (2013) · Mechanics & Industry · doi:10.1051/meca/2013046 · Cited by 2
Static and Vibration Analysis of Composite Beams Using Finite Element Methods
Rao, L. M., & Mitra, S. P. (2015) · Cited by 2
Dynamic Efficiency of a Container Crane’s Hoisting Transmission System under Hoisting Dynamic Load
Liu, Y., Zhang, Q., Qin, X., et al. (2016) · Shock and Vibration · doi:10.1155/2016/4847250 · Cited by 2
“In previous research [10, 11], the power loss in meshing teeth and rolling bearings is calculated by static load.”
MethodContribution to the study of power losses due to friction phenomenon between spur gear teeth
MUSHIRABWOBA, B., LAHCEN, B., NAJJI, B., et al. (2016) · Materials research proceedings · doi:10.21741/9781945291197-16 · Cited by 2
Design of helical gear transmission systems with high power density
Wang, C. (2018) · Journal of Engineering Research · doi:10.1016/s2307-1877(25)00598-x · Cited by 2
Choudhari, D. S., Kakhandki, V. J., & Iyer, G. (2021) · Materials Today Proceedings · doi:10.1016/j.matpr.2021.09.419 · Cited by 2
Load share model based gear loss factor prediction in high contact ratio spur gear drive
Ravivarman, R., & Sekar, R. P. (2022) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/13506501221107904 · Cited by 2
A Tribo‐Dynamic Model of a Helical Gear Pair Based on the Finite Line Contact Theory
Liu, M., Ouyang, Z., Yan, C., et al. (2023) · Mathematical Problems in Engineering · doi:10.1155/2023/5526740 · Cited by 2
A New Direct and Inexpensive Method and the Associated Device for the Inspection of Spur Gears
Alaci, S., Ciornei, F. C., Romanu, I.-C., et al. (2023) · Machines · doi:10.3390/machines11121046 · Cited by 2
Ge, H., & Wang, C. (2019) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/542/1/012044 · Cited by 2
Power Loss Evaluation of Automated Manual Transmission with Gearshift Assistant Mechanism
Zhiqiang, S., Gao, B., Jin, J., et al. (2021) · International Journal of Automotive Technology · doi:10.1007/s12239-021-0041-3 · Cited by 2
Influence of running-in on gear efficiency
Sjöberg, S. (2014) · KTH Publication Database DiVA (KTH Royal Institute of Technology) · Cited by 2
Xu, J., Jiao, C., Zou, D., et al. (2021) · Journal of Vibration Engineering & Technologies · doi:10.1007/s42417-021-00374-y · Cited by 1
Influence of Profile Correction Factor on Asymmetric Spur Gear Efficiency
Sekar, R. P. (2022) · Journal of The Institution of Engineers (India) Series C · doi:10.1007/s40032-022-00878-w · Cited by 2
“2773 × 10–8 1/Pa [11]), which is written as,”
BackgroundMethodInfluentialSun, W. F., Shi, X., Lu, X., et al. (2024) · Proceedings of the Institution of Mechanical Engineers Part E Journal of Process Mechanical Engineering · doi:10.1177/09544089241230879 · Cited by 1
Performance improvement of set of worm gears used in soot blower through profile modification
Honkalas, R., Deshmukh, B. B., Pawar, P., et al. (2024) · Frontiers in Mechanical Engineering · doi:10.3389/fmech.2024.1360502 · Cited by 1
Dynamic characteristics of pitted gear with variation of tooth surface topography
Liu, X., Xiong, Q., Liu, C., et al. (2025) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/09544062251372696 · Cited by 1
“10 Based on elastic fluid mechanics and boundary lubrication theory, Xu et al. 11 introduced a new formula for characterizing the tooth surface friction coefficient, which has been widely applied by researchers.”
Sekar, R. P. (2025) · Forschung im Ingenieurwesen · doi:10.1007/s10010-025-00925-9 · Cited by 1
Handschuh, M. J., Schragal, A., Kahraman, A., et al. (2026) · Lecture notes in mechanical engineering · doi:10.1007/978-981-95-3650-4_65 · Cited by 1
Self-citationInfluence of dynamics on gear meshing power loss
Marafona, J. D. M., Fernandes, C. M. C. G., & Marques, P. M. T. (2026) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2025.106339 · Cited by 1
Mo, S., Dong, S., Gao, D., et al. (2026) · Nonlinear Dynamics · doi:10.1007/s11071-025-12141-9 · Cited by 1
Ding, X., Wang, W., Chen, X., et al. (2026) · International Journal of Automotive Technology · doi:10.1007/s12239-026-00451-9 · Cited by 1
Handschuh, M. J., & Schragal, A. (2026) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/13506501261438363 · Cited by 1
混合潤滑状態にある転がり-すべり接触面の摩擦係数推定式(第2報) : 摩擦係数に及ぼす表面粗さ形状の影響
松本, 將., & 豊田, 展. (2013) · トライボロジスト · doi:10.18914/tribologist.58.09_676 · Cited by 1
Korde, A., & Wilson, B. K. (2009) · Cited by 1
Shon, S. (2012) · OhioLink ETD Center (Ohio Library and Information Network) · Cited by 1
Prediction and Minimization of Mechanical Power Loss of Gear Pair via Analytical Approach
Park, K., Harianto, J., & Kahraman, A. (2017) · Transactions of Korean Society of Automotive Engineers · doi:10.7467/ksae.2017.25.4.498 · Cited by 1
Self-citationKoçak, S., Kaplan, Y., & Güner, A. T. (2020) · Gazi Üniversitesi Fen Bilimleri Dergisi Part C Tasarım ve Teknoloji · doi:10.29109/gujsc.652499 · Cited by 1
Zhou, X., Ruan, J., Zhu, B., & Zhang, N. (2018) · International Journal of Vehicle Performance · doi:10.1504/ijvp.2018.095316 · Cited by 1
Investigation of Spur Gear Dynamics with Gear MeshImpacts Induced by Tooth Wear
Sun, X., Zhang, R., Wang, Z., et al. (2022) · Journal of Physics Conference Series · doi:10.1088/1742-6596/2184/1/012039 · Cited by 1
“is the time-varying friction coefficient which was proposed by [14].”
BackgroundStudy of Gear Meshing Efficiency of Electric Drive Axle with Considering System Deformation
Qin, W., Di, H., Liangji, F., et al. (2023) · Journal of Mechanical Engineering · doi:10.3901/jme.2023.03.066 · Cited by 1
An investigation of the wear and efficiency in non-standard internal spur gear set
Ravivarman, R., & Sekar, R. P. (2023) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/13506501231205172 · Cited by 1
Validation of Gear Friction Equation Using Directional Parameter
HONGU, J., Hattori, S., Kato, J., & KOIDE, T. (2024) · Journal of Tribology · doi:10.1115/1.4064677 · Cited by 1
Bending Strength Design for an e-PGS Pinion Under Friction
Kwon, S.-M., & Lee, Y. (2024) · Journal of the korean society of manufacturing technology engineers · doi:10.7735/ksmte.2024.33.2.99 · Cited by 1
Yu-jing, Z., & Degong, C. (2013) · doi:10.1109/mec.2013.6885620 · Cited by 1
“Due to the increasing energy demand and energy costs, as well as the energy shortage, improving the transmission efficiency of gear has an important role on reducing energy consumption, saving energy and improving the economic benefit, so the gear transmission efficiency has been a more important research topic [1-3].”
BackgroundJANAKIRAMAN, V., Kahraman, A., & Talbot, D. C. (2017) · Journal of Advanced Mechanical Design Systems and Manufacturing · doi:10.1299/jamdsm.2017jamdsm0080 · Cited by 1
Self-citationTheerarangsarit, K., & Ratanasumawong, C. (2017) · Engineering Journal · doi:10.4186/ej.2017.21.7.427 · Cited by 1
Wang, C. (2018) · Journal of the Brazilian Society of Mechanical Sciences and Engineering · doi:10.1007/s40430-018-1428-6 · Cited by 1
Efficiency Analysis of Gear System Based on Gear Surface Micro-topography
Liu, W., Shao, Y., Li, H., Yan, C., & Xu, J. Y. (2018) · International Conference on Control, Automation and Systems (ICCAS) · Cited by 1
Sekar, R. P. (2020) · Journal of solid mechanics. · doi:10.22034/jsm.2019.579286.1354 · Cited by 3
“The coefficient of friction between the teeth contact pair can be determined by using the model proposed by Xu [30] which includes parameters like load share, contact pressure, surface roughness, dynamic viscosity of lubricant, radius of curvature and entrainment velocity.”
BackgroundMethodImpact of NiB Coating on the Efficiency, Scuffing, and Wear of Gear Contacts
Kahraman, A. (2013) · Defense Technical Information Center (DTIC) · doi:10.21236/ada583849 · Cited by 1
“Some of these studies (4, 8, 9) also indicate that increased viscosity causes load-independent power losses (due to churning and gear-mesh pocketing) and, in the process, wipes out some or most of the reductions in mechanical losses.”
InfluentialSelf-citationA Model to Study the Effect of Micropitting on the Dynamic Behaviour of a Geared SystemPreprint
Portron, S., & Marques, P. M. T. (2024) · SSRN Electronic Journal · doi:10.2139/ssrn.4900642 · Cited by 1
Deep learning prediction of EHL friction using full surface roughness profiles: An LSTM-MLP approach
Li, S. (2026) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2026.106417 · Cited by 1
Modeling and Analysis of the Meshing Losses of Involute Spur Gears in High-Speed and High-Load
Chang, L., Jeng, Y., & Huang, P. (2013)
ALTERNATE SLIDING FRICTION FORMULATIONS OF ELASTO - HYDRODYNAMIC OF SPUR GEARS
Al-Zubaidi, A. F. A. (2008) · Journal of Engineering · doi:10.31026/j.eng.2008.04.05
New software package for power and efficiency analysis of epicyclic gear transmissions
Chen, J., & Chen, C. (2015) · DMG-Lib Digital Mechanism and Gear Library · doi:10.6567/iftomm.14th.wc.os6.016
ANALYSIS OF GEAR PAIR CONTACT TO PRIDICT EFFICIENCY
Lahane, R. S., Jawale, H. P., & Patil, D. (2015)
Christodoulias, A. I. (2017) · doi:10.25560/67503 · Cited by 1
Upon the efficiency of gear transmissions
Alaci, S., Ciornei, F. C., Pentiuc, R. D., Ciornei, M. C., & Romanu, I.-C. (2020) · Journal of Physics Conference Series · doi:10.1088/1742-6596/1426/1/012012
Efficiency and Durability of DLC-Coated Gears
Barbieri, M., Iarriccio, G., Pellicanò, F., et al. (2020) · Mechanisms and machine science · doi:10.1007/978-3-030-55807-9_65
Design and Verification of MIL for Linear Actuator
Holmér, N. (2020) · KTH Publication Database DiVA (KTH Royal Institute of Technology)
Mesh stiffness of cylindrical gear including tooth surface – Friction based on FEA method
Geng, L., Mimi, N., Lan, L. G., et al. (2017) · VDI Verlag eBooks · doi:10.51202/9783181022948-807
Berri, P. C., Vedova, M. D. L. D., Maggiore, P., et al. (2021) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/1024/1/012097
“In the case of planetary gearboxes, some elements may experience high torques and high speed at the same time: hence, the mechanical power recirculating through these elements can be many times larger than the transmitted power, leads to increased losses and brings down the overall efficiency of the gearbox [3-7].”
BackgroundEffects of Misalignment on the Sliding Rates of Parallel Line Gear Pair
Lin, Y., & Chen, Y. (2021) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/1102/1/012014
“Introduction Relative sliding between the meshing surfaces occurs throughout the meshing process (except for the pitch point) of the commonly used gear pairs [1, 2].”
BackgroundDynamic Interaction Between Transmission Error and Friction Coefficients for FZG-A10 Spur Gears
Hammami, M., Ksentini, O., Féki, N., et al. (2021) · Applied condition monitoring · doi:10.1007/978-3-030-76517-0_16
Friction Dynamics of Manipulators
Liu, S., & Chen, G. (2018) · Wiley eBooks · doi:10.1002/9781119422518.ch4
Helu, M., Diaz-Elsayed, N., & Dornfeld, D. A. (2018) · doi:10.1002/9781119519904.ch9
Comprehensive Review of Gear Trains with Applications
Dharshini, S., Deepan Kumar, K., & babu, D. (2020) · International Research Journal on Advanced Science Hub · doi:10.47392/irjash.2020.15
Minimum Friction Losses in Planetary Stages of Wind Turbine Gearboxes
Pedrero, J. I., Sánchez, M. B., Guerra, D., et al. (2022) · Mathematical Problems in Engineering · doi:10.1155/2022/5111827
Analytical algorithm for time-varying friction force and torque of pitting helical gear
Wang, Z., Shi, L., Liu, Z., et al. (2022) · Journal of Physics Conference Series · doi:10.1088/1742-6596/2369/1/012025
“Regression formula calculation coefficients [12].”
BackgroundInfluence of time-varying friction on the nonlinear dynamic characteristics of helical gear
Zhang, W., Song, Q., & Lai, W. (2023) · International Conference on Mechanical, Electronics and Electrical and Automation Control (METMS) · doi:10.1117/12.2679737
“Based on non-Newtonian thermal elastohydrodynamic lubrication theory, Kahraman obtained an accurate formula of variable friction coefficient to predict the friction coefficient distribution of all contact points of gear meshing [9,10].”
MethodJiang, H., Liu, F., Zhang, J., et al. (2023) · SSRN Electronic Journal · doi:10.2139/ssrn.4568347
วธออกแบบเฟองบนเพลาขนานใหมกำลงสญเสยนอยทสดและผลกระทบตอลกษณะการสนสะเทอน
ธีระรังสฤษดิ์, ก. (2016) · doi:10.58837/chula.the.2016.884
Research on the Structure of a New Integrated Cooling Channel for Electric Motor and Reducer
Wu, A., Li, T. X., Chen, X., et al. (2023) · International Conference on Electrical Machines and Systems (ICEMS) · doi:10.1109/icems59686.2023.10345348
“Xu proposed a calculation model for the mechanical efficiency loss of the reducer, and compared the measured efficiency of gear pairs with different gear designs and surface treatments with the predicted efficiency of the model [6].”
BackgroundHigh Speed Driveline Power Loss and Influencing Factors
Jain, S., & Singh, P. (2024) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2024-26-0337
Multibody Lubrication Dynamics of Mechanical Transmission System
Qiu, L., & Chen, X. (2024) · Lecture notes in mechanical engineering · doi:10.1007/978-981-99-8048-2_18
Track System Dynamic Analysis by the Riccati Multibody System Transfer Matrix Method
Miao, Y., Rui, X., Wang, P., et al. (2024) · Lecture notes in mechanical engineering · doi:10.1007/978-981-99-8048-2_161
Mo, S., Zhang, Y., Chen, K., et al. (2024) · International Journal of Bifurcation and Chaos · doi:10.1142/s0218127424501219
Qinhe, G., Lei, G., Zhihao, L., Wang, D. J., Dong, M., & Yibo, Z. (2024) · Scientific insights and discoveries review · doi:10.59782/sidr.v5i1.165
Zhang, X., Xia, H., Meng, F., Sun, J., & Wang, J. (2025) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/09544062251343470
HONGU, J., Hashimoto, S., Kato, J., et al. (2025) · Forschung im Ingenieurwesen · doi:10.1007/s10010-025-00862-7
Mixed and thermal elastohydrodynamic simulation of cylindrical gear designs
Farrenkopf, F., Lohner, T., & Stahl, K. (2025) · Forschung im Ingenieurwesen · doi:10.1007/s10010-025-00882-3
Metadata
- Authors
- Xu, H., Kahraman, A., Anderson, N. E., & Maddock, D. G.
- Affiliations
- The Ohio State University (US)
- General Motors (United States) (US)
- Venue
- Journal of Mechanical Design
- Publisher
- ASME International
- Published
- 2006-06-14
- Volume
- 129
- Issue
- 1
- Pages
- 58-68
- ISSN
- 0161-8458 (ISSN-L)
- 1050-0472
- 1528-9001
- OpenAlex
- W1970036055
- Semantic Scholar
- e4f46f1dbb4c333508d9b97b58992c11dcdd3355
- Cited by
- 323
- References
- 40
- Citations by year
- 2026: 22 · 2025: 31 · 2024: 28 · 2023: 23 · 2022: 25 · 2021: 26 · 2020: 23 · 2019: 15 · 2018: 20 · 2017: 13 · 2016: 12 · 2015: 17 · 2014: 19 · 2013: 11 · 2012: 9
- FWCI
- 13.71
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Journal of Mechanical Design (publishedVersion)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Gear and Bearing Dynamics Analysis
- Physical Sciences › Engineering › Mechanical Engineering › Tribology and Lubrication Engineering
- Physical Sciences › Engineering › Mechanics of Materials › Tribology and Wear Analysis
- Keywords
- parallel-axis gears, friction losses, gear load distribution, friction coefficient, elastohydrodynamic lubrication, non-Newtonian lubrication, tooth modification, lubricant properties, gear geometry
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.