Prediction of Mechanical Efficiency of Parallel-Axis Gear Pairs
The DOI matches its Crossref record; 35 of the 40 references it cites were found in a registry or an index.
Abstract
A computational model is proposed for the prediction of friction-related mechanical efficiency losses of parallel-axis gear pairs. The model incorporates a gear load distribution model, a friction model, and a mechanical efficiency formulation to predict the instantaneous mechanical efficiency of a gear pair under typical operating, surface, and lubrication conditions. The friction model uses a new friction coefficient formula obtained by using a validated non-Newtonian thermal elastohydrodynamic lubrication (EHL) model in conjunction with a multiple linear regression analysis. The load and friction coefficient distribution predictions are used to compute instantaneous torque/power losses and the mechanical efficiency of a gear pair at any given rotational position. Efficiency measurements from gear pairs having various gear designs and surface treatments are compared to model predictions. Mechanical efficiency predictions are shown to be within 0.1% of the measured values, indicating that the proposed efficiency model is accurate. Results of a parametric study are presented at the end to highlight the influence of key basic gear geometric parameters, tooth modifications, operating conditions, surface finish, and lubricant properties on mechanical efficiency losses.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Citations
Cites
Gear Geometry and Applied Theory
Litvin, F. L., & Fuentes, A. (2004) · Cambridge University Press eBooks · doi:10.1017/cbo9780511547126 · Cited by 2,332
Elasto-Hydrodynamic Lubrication
(1977) · Elsevier eBooks · doi:10.1016/c2013-0-05764-7 · Cited by 591
Applied Tribology: Bearing Design and Lubrication
Kennedy, F. E. (2002) · Journal of Tribology · doi:10.1115/1.1432665 · Cited by 325
Handbook of Practical Gear Design
Dudley, D. W. (1984) · Medical Entomology and Zoology · Cited by 286
Applied Tribology: Bearing Design and Lubrication
Khonsari, M. M., & Booser, E. R. (2017) · Wiley eBooks · doi:10.1002/9781118700280 · Cited by 235
Instantaneous Coefficients of Gear Tooth Friction
Benedict, G. H., & Kelley, B. W. (1961) · A S L E Transactions · doi:10.1080/05698196108972420 · Cited by 201
Fourth Paper: Shear Behaviour of Elastohydrodynamic Oil Films at High Rolling Contact Pressures
Johnson, K. L., & Cameron, R. (1967) · Proceedings of the Institution of Mechanical Engineers · doi:10.1243/pime_proc_1967_182_029_02 · Cited by 162
Development of a generalized mechanical efficiency prediction methodology for gear pairs
Xu, H. J. (2005) · OhioLink ETD Center (Ohio Library and Information Network) · Cited by 161
Self-citationChittenden, R. J., Dowson, D., Dunn, J. F., & Taylor, C. M. (1985) · Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences · doi:10.1098/rspa.1985.0015 · Cited by 155
Conry, T. F., & Seireg, A. (1973) · Journal of Engineering for Industry · doi:10.1115/1.3438259 · Cited by 145
Research works printed but not linked: 7
- Reuleaux, Friction in Tooth Gearing, Trans. ASME, VIII, 45
- Kelley, Lubrication of Involute Gearing, Proc. Inst. Mech. Eng., 182, 173
- Dowson, A Theory of Involute Gear Lubrication, 8
- Simon, V. , 1981, “Load Capacity and Efficiency of Spur Ears in Regard to Thermo-End Lubrication,” International Symposium on Gearing and Power Transmissions, Tokyo, Japan.
- Mihalidis, A., Bakolas, V., Panagiotidis, K., and Drivakos, N., 2002, “Prediction of the Friction Coefficient of Spur Gear Pairs,” VDI-Berichte, NR. 1665, pp. 705–719.
- Chittenden, A Theoretical Analysis of The Isothermal Elastohydrodynamic Lubricant of Concentrated Contacts, Proc. R. Soc. London, Ser. A, 397, 271
- Johnson, Shear Behavior of Elastohydrodynamic Oil Films at High Rolling Contact Pressures, Proc. Inst. Mech. Eng., 182, 307
Cited by
Items 101–200 of 320
Zhao, X., Fan, W., Wang, Z., et al. (2023) · Wear · doi:10.1016/j.wear.2023.204802 · Cited by 16
CFD based Prediction of Spin Power Loss of Automotive Differential System
Renjith, S., Srinivasa, V. K., & Shome, B. (2015) · SAE International journal of commercial vehicles · doi:10.4271/2015-01-2783 · Cited by 16
Sekar, R. P., Varuvel, E. G., & Martin, L. J. (2017) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/1350650117697594 · Cited by 18
“62 for i1⁄4 1–9, respectively.(10) In this work, the load share (F) by a teeth pair and the respective contact stresses (sH) are evaluated by using multi-pair finite element contact model.”
BackgroundMethodInfluentialAnalytical synthesis of the kinematic geometry of spiral bevel gears of pure-rolling contact
Zhang, W., Tan, R., Guo, X., et al. (2020) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2020.103992 · Cited by 16
Dindar, A., Hong, I. J., Garg, A., & Kahraman, A. (2021) · Tribology Transactions · doi:10.1080/10402004.2021.1937760 · Cited by 19
Self-citationXu, J., Xue, L., Zou, D., et al. (2022) · Journal of Sound and Vibration · doi:10.1016/j.jsv.2022.117508 · Cited by 15
Talbot, D. C., Kahraman, A., Stilwell, A. W., Singh, A., & Napau, I. (2015) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/0954406215587539 · Cited by 17
Self-citationWang, S., & Zhu, R. (2020) · Vibroengineering PROCEDIA · doi:10.21595/vp.2020.21671 · Cited by 15
“For the full film lubrication condition [18], the coefficient of fiction can be calculated by: μ = e , , , P |SR| V v R , (2) f SR,P ,v , S = b + b |SR|P log v + b e | | + b e , (3) where, b are constant coefficients that shown in Table 2, SR indicates the slide-roll ratio, P indicated the maximum Hertzian pressure, v…”
MethodEnergy efficiency measurement procedure for gearboxes in their entire operating range
Derammelaere, S., Dereyne, S., Defreyne, P., et al. (2014) · doi:10.1109/ias.2014.6978376 · Cited by 15
“Literature concerning the energy efficiency of gearboxes is limited to models describing the energy behavior of certain components of a gearbox such as gear pairs [5], [6] or the behavior of lubrication [7].”
BackgroundModeling and analysis of the dynamic efficiency of manual transmission/reducer
Wang, B., Lu, Z., Chen, D., Wang, P., Luo, W. H., & Xu, H. (2015) · International Journal of Automotive Technology · doi:10.1007/s12239-015-0043-0 · Cited by 15
“experiment results from (Xu et al., 2007; Zhou, 2004) are presented.”
BackgroundMethodResultInfluentialSelf-citationWang, C., Cui, H. Y., Zhang, Q. P., & Wang, W. M. (2015) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/0954406215573977 · Cited by 17
“Xu et al.(6) proposed a load distribution model (LDP) to calculate the load distribution of parallel-axis gear pairs.”
BackgroundMethodInfluentialSimulations of drag torque affecting synchronisers in a dual clutch transmission
Walker, P. D., Zhang, N., Tamba, R., et al. (2011) · Japan Journal of Industrial and Applied Mathematics · doi:10.1007/s13160-011-0030-4 · Cited by 15
“Xu et al. [ 24 ] reviews many of the current friction models and identifies a flaw in many friction models in that as the sliding velocity approaches zero at the pitch point the friction coefficient approaches infinity.”
BackgroundMethodInfluentialDong, H., Liu, Z.-Y., Duan, L.-L., & Hu, Y. (2018) · PLoS ONE · doi:10.1371/journal.pone.0198677 · Cited by 16
On the Effect of DLC and WCC Coatings on the Efficiency of Manual Transmission Gear Pairs
Laderou, A., Mohammadpour, M., Theodossiades, S., Daubney, R., & Meeks, G. (2020) · Applied Sciences · doi:10.3390/app10093102 · Cited by 16
“Hence, the contact area of the gear mesh is approximated as a straight line [19].”
BackgroundYang, J., & Lin, T. (2022) · Meccanica · doi:10.1007/s11012-022-01625-2 · Cited by 14
“(1234567890) where ξij(t) is the scaling factor for hydrodynamic part, μaij denotes the friction coefficient at each contact point for asperity contact, μhij(t) represents the friction coefficient at each contact point for lubricant film, which can be calculated by the formula proposed by Xu [24].”
BackgroundMethodHuang, K., Zhu, G., Xiong, Y., et al. (2025) · Nonlinear Dynamics · doi:10.1007/s11071-024-10775-9 · Cited by 14
A dynamic calculation method of sliding friction losses for a helical gear pair
Wang, C., & Shi, Z. (2016) · Journal of the Brazilian Society of Mechanical Sciences and Engineering · doi:10.1007/s40430-016-0585-8 · Cited by 15
“1 Comparison of experimental value and theoretical value of meshing efficiency [6]”
BackgroundMethodInfluentialAN EXPERIMENTAL INVESTIGATION OF HELICAL GEAR EFFICIENCY
Vaidyanathan, A. (2009) · OhioLink ETD Center (Ohio Library and Information Network) · Cited by 22
Wink, C. H., Marson, L., & Goyal, S. (2019) · Tribology International · doi:10.1016/j.triboint.2019.106070 · Cited by 14
Wang, S., & Zhu, R. (2021) · Journal of Tribology · doi:10.1115/1.4052941 · Cited by 13
Xu, J., Liu, X., Xie, Z., et al. (2024) · Applied Ocean Research · doi:10.1016/j.apor.2023.103863 · Cited by 13
Simulation and experiment of viscous torque for disengaged wet clutches of tracked vehicle
Wei, B., Yong-yong, H., Wang, W., & jianbin, L. (2018) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/1350650118788143 · Cited by 13
Wang, C., & Ken, M. (2020) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/1350650120966894 · Cited by 14
Estimation of Sliding Loss in a Parallel-Axis Gear Pair
Ratanasumawong, C., ASAWAPICHAYACHOT, P., Phongsupasamit, S., et al. (2012) · Journal of Advanced Mechanical Design Systems and Manufacturing · doi:10.1299/jamdsm.6.88 · Cited by 13
Contact dynamics analysis of the single-pin meshing pair of a tracked vehicle
Wang, P., Wang, G., Rui, X., et al. (2021) · Nonlinear Dynamics · doi:10.1007/s11071-021-06327-0 · Cited by 12
Power loss scaling laws of high-speed planetary reducers
Aroua, A., Defreyne, P., Verbelen, F., et al. (2023) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2023.105428 · Cited by 12
Dynamic analysis of gear system with multiple lubrication states in torque–speed parameter space
Mo, S., Zhang, Y., Chen, K., et al. (2024) · Meccanica · doi:10.1007/s11012-024-01825-y · Cited by 12
“Xu et al. [13] proposed a calculation model for predicting the mechanical efficiency loss of parallel shaft gear pairs, in which the friction coefficient was obtained by empirical formula combined with multiple linear regression analysis.”
Giudice, F., & Rosa, G. L. (2009) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2008.11.010 · Cited by 12
Basan, R., & Marohnić, T. (2019) · Fatigue & Fracture of Engineering Materials & Structures · doi:10.1111/ffe.12997 · Cited by 12
Mao, H., Sun, Y., Xu, T., et al. (2021) · Mathematical Problems in Engineering · doi:10.1155/2021/8886792 · Cited by 12
“+e calculation parameters are detailed in the literature [17].”
BackgroundMethodInfluentialDynamic characteristics of helical gear with root crack and friction
Mo, S., Wang, D., Hu, X., et al. (2023) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/09544062221145518 · Cited by 11
Sun, M., Lu, C., Liu, Z., Sun, Y., Chen, H., & Shen, C. (2020) · Shock and Vibration · doi:10.1155/2020/9834939 · Cited by 14
A methodology to predict power losses of planetary gear sets
Talbot, D. C., & Kahraman, A. (2014) · Elsevier eBooks · doi:10.1533/9781782421955.625 · Cited by 13
Self-citationPerformance enhancement of spur gear formed through asymmetric tooth
Sekar, R. P. (2019) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/1350650119837822 · Cited by 12
Im, D., Kim, T., Kim, B.-S., Park, J.-H., Kim, J.-G., & Park, Y.-J. (2025) · Tribology International · doi:10.1016/j.triboint.2025.110597 · Cited by 10
Zhao, W., Liu, J., Zhao, W., et al. (2023) · Journal of Vibration Engineering & Technologies · doi:10.1007/s42417-023-01118-w · Cited by 10
“(11) Time-varying friction coefficient can be given by [35]: where v 0 represents the absolute viscosity; b i ( i = 1, 2, ⋯ , 9 ) represent regression coefficients, and their values are dependent on the lubricant types [36]; S f represents the surface roughness.”
Zhang, T., Lin, T., & Jing, W. P. (2025) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2025.112801 · Cited by 10
Mo, S., Zhang, Y., Liu, Y., et al. (2025) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2025.106169 · Cited by 10
Ren, J., & Yuan, H. (2022) · Coatings · doi:10.3390/coatings12091250 · Cited by 10
“Conclusion and further study are made in Section 5.”
BackgroundA Novel Formula for Instantaneous Coefficients of Sliding Friction in Gearing
Xu, H. J. (2007) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2007-01-4207 · Cited by 10
Self-citationGearbox Mechanical Efficiency Determination by Strain Gauges Direct Application
Lopot, F., Dub, M., Flek, J., et al. (2021) · Applied Sciences · doi:10.3390/app112311150 · Cited by 10
“In the article [1], Xu, Kahraman, Anderson, and Maddock discuss a gear load distribution model and a friction model, and they define mechanical efficiency based on typical operating conditions.”
BackgroundMinimum friction losses in wind turbine gearboxes
Pedrero, J. I., Martínez-López, D., Calvo-Irisarri, J., et al. (2021) · Forschung im Ingenieurwesen · doi:10.1007/s10010-021-00526-2 · Cited by 9
Wang, J., Yao, Z., Hassan, M. F., et al. (2021) · Engineering Computations · doi:10.1108/ec-03-2021-0183 · Cited by 9
Sundar, S., Dreyer, J. T., & Singh, R. (2015) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2014.11.015 · Cited by 9
“[16] and Xu and Kahraman [33] conducted experiments under the Elastohydrodynamic lubrication (EHL) regime, and hence their μ values are very low.”
BackgroundInfluentialLiu, Z., Shen, Y., & Rinderknecht, S. (2019) · SAE International Journal of Advances and Current Practices in Mobility · doi:10.4271/2019-01-0028 · Cited by 9
A novel design for enhancing the surface durability of the spur gear systems
Hussein, A. W., & Abdullah, M. Q. (2022) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/09544062221100080 · Cited by 9
Chen, Z., Dong, Q., Shi, X., et al. (2025) · Fatigue & Fracture of Engineering Materials & Structures · doi:10.1111/ffe.14555 · Cited by 8
Modeling and Analysis of High-Load and High-Speed Involute Spur Gear Systems in Adverse Lubrication
Chang, L., Yu, Q., & Jeng, Y. (2017) · Tribology Transactions · doi:10.1080/10402004.2017.1321812 · Cited by 8
Frictional dynamic model predictions of FZG-A10 spur gear pairs considering profile errors
Féki, N., Hammami, M., Ksentini, O., Abbès, M. S., & Haddar, M. (2020) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/1350650120962973 · Cited by 8
Estimation of Gear Friction Coefficient Using Directional Parameter of Tooth Surface
HONGU, J., Horita, R., & KOIDE, T. (2021) · Journal of Tribology · doi:10.1115/1.4052558 · Cited by 9
Reduction of tooth wear on asymmetric spur gear through profile correction factors
Sekar, R. P. (2022) · Australian Journal of Mechanical Engineering · doi:10.1080/14484846.2022.2113619 · Cited by 8
Transmission configuration effect on total efficiency of Electric Vehicle powertrain
Tehrani, M. G., Kelkka, J., Sopanen, J., Mikkola, A., & Kerkkänen, K. S. (2014) · European Conference on Power Electronics and Applications · doi:10.1109/epe.2014.6910780 · Cited by 15
“In order to calculate the friction coefficient, a variety of friction models, such as the Coulomb Model, Benedict and Kelley Model, Xu’s full Model and Smoothened Coulomb Model, have been proposed [5].”
BackgroundMethodInfluentialDevelopment of an efficiency model for manual transmissions
Rosander, P., Bednarek, G., Seetharaman, S., & Kahraman, A. (2008) · ATZ - Automobiltechnische Zeitschrift · doi:10.1007/bf03225001 · Cited by 12
Self-citationLubricated loaded tooth contact analysis for spur gear pair
Oglieve, C., Sivayogan, G., Mohammadpour, M., & Rahnejat, H. (2019) · International Journal of Powertrains · doi:10.1504/ijpt.2019.098119 · Cited by 8
Borsboom, O., de Mooy, T., Salazar, M., & Hofman, T. (2023) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2023.10.1303 · Cited by 10
Zheng, J., Qin, D., Liu, C., et al. (2025) · Journal of Tribology · doi:10.1115/1.4067812 · Cited by 7
Du, Q., Yang, G., Wang, W., et al. (2025) · Actuators · doi:10.3390/act14040173 · Cited by 7
“…to acquire the coefficient of friction, which can be grouped into two categories, one is applying a user-defined constant value as the average coefficient of friction [18,19], the other is calculating the instantaneous value of µ based on the Elasto-Hydrodynamic Lubrication (EHL) theory [20–25].”
Sedak, M., & Rosić, M. B. (2023) · Applied Sciences · doi:10.3390/app132111682 · Cited by 7
Dong, H., Bi, Y., Bing-Xing, R., et al. (2024) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/09544062241227322 · Cited by 7
“In the potential energy method, 23 based on the knowledge of material mechanics and elasticity, the total potential energy stored in the meshing gear system can be divided into four components: Hertzian energy U h , bending energy U b , shear energy U s and axial compression energy U a , which are…”
Wang, Q., Wang, Q., Gui, L., & Fan, Z. (2022) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/09544062221075528 · Cited by 8
“(3) The corner contact effects prolonged the load distribution from engagement to disengagement and affected the mechanical efficiency, especially the instantaneous mechanical efficiency.”
BackgroundAhssan, M. R., Ektesabi, M. M., & Gorji, S. A. (2023) · Energies · doi:10.3390/en16052496 · Cited by 7
Li, Y., Yuan, S., Wu, W., et al. (2023) · Machines · doi:10.3390/machines11070696 · Cited by 7
Gu, Y., Chen, R., Qiu, G., et al. (2024) · Quality and Reliability Engineering International · doi:10.1002/qre.3487 · Cited by 7
“The speed of gear-1 is set as 1000 r/min, and the load on gear-2 is set as 19.8N ⋅ m. Generally, the boundary friction coefficient ranges from 0.08 to 0.13, 26,41 therefore, the boundary friction coefficient 𝜇 F = 0.1 26 is selected in this study.”
BackgroundMethodInfluentialModeling Parametric Vibration Of Multistage Gear Systems As A Tool For Design Optimization
Kuria, J., & Kihiu, J. M. (2008) · doi:10.5281/zenodo.1054862 · Cited by 7
Modeling of dynamic efficiency of curve–face gear pairs
Lin, C., & Cai, Z. (2015) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/0954406215623308 · Cited by 7
“(3) Due to the dynamic behavior (mainly the dynamic-loading unit load and relative velocity as shown in Figure 9) changing, the variation process of dynamic-loading results is more complex than the quasi-static results as shown in Figure 10.”
BackgroundResultThe influence of friction on the tooth normal force of spur and helical gears
Reimann, T., Herzog, T. R., Kadach, D., et al. (2019) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/0954406219855097 · Cited by 7
Xiao, H., Zhang, F., Li, Z., et al. (2025) · Meccanica · doi:10.1007/s11012-025-02019-w · Cited by 6
“…cylindrical roller pair has been widely used to perform the frictional contact experiments of gear pairs, which can simulate the line-con-tact EHL of gear meshing at different meshing positions along the line-of-contact through adjusting the slip-to-roll ( SR ) ratio between the two rollers [38].”
Zhang, T., Lin, T., & Xiang, Y. (2025) · Aerospace Science and Technology · doi:10.1016/j.ast.2025.111405 · Cited by 6
A Method for Calculating Elliptic Gear Transmission Efficiency Based on Transmission Experiment
Dong, C., Liu, Y., & Zhao, G. (2021) · Strojniški vestnik – Journal of Mechanical Engineering · doi:10.5545/sv-jme.2021.7318 · Cited by 6
A model to study the effect of micropitting on the dynamic behaviour of a geared system
Portron, S., & Marques, P. M. T. (2024) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2024.105854 · Cited by 6
Zhou, S., Zhou, Y., Li, Y., et al. (2022) · International Journal of Bifurcation and Chaos · doi:10.1142/s0218127422500092 · Cited by 6
A Theoretical and Experimental Study on the Power Loss of Gearbox Based on Dimensionless Analysis
Guo, D. M., Wen, G., Wang, Y., et al. (2023) · Journal of Tribology · doi:10.1115/1.4062449 · Cited by 6
Influence of tooth profile and surface roughness on wear of spur gears considering temperature
Park, C. I. (2023) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-023-0931-6 · Cited by 6
“The friction coefficient is calculated by the friction equation by Xu et al. [23], which has no sliding friction at the pitch point owing to the pure rolling motion.”
MethodEstimation and Improvement Method of Mesh Efficiency of Cylindrical Gears
MORIKAWA, K. (2012) · TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series C · doi:10.1299/kikaic.78.1250 · Cited by 6
Entwicklung eines Wirkungsgrad-modells für Schaltgetriebe
Rosander, P., Bednarek, G., Seetharaman, S., & Kahraman, A. (2008) · ATZ - Automobiltechnische Zeitschrift · doi:10.1007/bf03221974 · Cited by 7
Self-citationSaravanan, L., & Senthilvelan, T. (2016) · Transactions of the Indian Institute of Metals · doi:10.1007/s12666-016-0849-0 · Cited by 6
Dynamic analysis of double-helical gear system considering effect of oil film among meshing teeth
Yin, M., Cui, Y., Meng, X., et al. (2014) · Advances in Mechanical Engineering · doi:10.1177/1687814020920117 · Cited by 6
The Calculation of Meshing Efficiency of a New Type of Conical Involute Gear
Yu, L., Wang, G., & Zou, S. (2017) · Strojniški vestnik – Journal of Mechanical Engineering · doi:10.5545/sv-jme.2016.3843 · Cited by 7
“The mechanical efficiency of parallel-axis gear pairs and cross-axis gear pairs were calculated in [14] and [15], the gear contact analysis model and a new friction coefficient formula based on Newtonian thermal elasto-hydrodynamic lubrication are applied.”
MethodEffect of Rim and Web Thickness on Tooth Root Stress of Spur Gear
Park, J. H., Chung, W.-J., Park, Y., et al. (2024) · International Journal of Automotive Technology · doi:10.1007/s12239-024-00020-y · Cited by 5
“Furthermore, the improvement in gear efficiency in power transmission systems is an area of interest in the automotive and aviation sectors, where weight reduction is crucial for improving the fuel economy (Anderson & Loewenthal, 1982; Petry-Johnson et al., 2008; Simon, 1981; Xu et al., 2007).”
Wang, X., Wen, L., Hu, D., et al. (2021) · Mechanical sciences · doi:10.5194/ms-12-677-2021 · Cited by 5
“…by load factor as follows: µ= sc ·µc+ (1− sc) ·µl, (15) where µc is the friction coefficient of boundary lubrication, which refers to the study reported by Wang et al. (2008). µl is the friction coefficient of elastohydrodynamic lubrication, which refers to the study reported by Xu et al. (2007).”
ResultXu, J., Xue, L., Zou, D., et al. (2024) · Acta Mechanica Sinica · doi:10.1007/s10409-023-23330-x · Cited by 5
Spur and Helical Gear Sliding Loss Model with Load Distribution Pattern on Gear Tooth Surface
Ponchai, N., Phraeknanthoe, J., & Ratanasumawong, C. (2018) · Engineering Journal · doi:10.4186/ej.2018.22.2.101 · Cited by 5
Preliminary Study of Frictional Power Losses in Spur Geared Transmissions
et.al., M. B. E. A. M. B., & TJPRC (2017) · International journal of mechanical and production engineering research and development · doi:10.24247/ijmperdaug201720 · Cited by 5
Study of Power Losses in a Two-Speed Dual Clutch Transmission
Zhou, X., Walker, P. D., Zhang, N., Zhu, B., & Ruan, J. (2014) · SAE technical papers on CD-ROM/SAE technical paper series · doi:10.4271/2014-01-1799 · Cited by 5
Dynamics of spur gear pairs considering meshing impacts based on energy methods
Zhu, L., Guan, Y., & Gou, X.-F. (2025) · Meccanica · doi:10.1007/s11012-025-01963-x · Cited by 4
“These parameters include meshing stiffness [2–5], friction coefficient [6–9], backlash [10, 11], elastoplastic lubrication [12–14], and tooth pitch deviation [15, 16].”
High-fidelity modelling of lubricated transmissions using a coupled finite element approach
Neeckx, S., Blockmans, B., Boukadia, R., Naets, F., & Desmet, W. (2024) · Mechanism and Machine Theory · doi:10.1016/j.mechmachtheory.2024.105695 · Cited by 6
Mixed and thermal elastohydrodynamic simulation of a low-loss gear considering the gear system
Farrenkopf, F., Lohner, T., & Stahl, K. (2025) · Friction · doi:10.26599/frict.2025.9441096 · Cited by 5
Mo, S., Zhang, Y., Chen, K., et al. (2025) · Nonlinear Dynamics · doi:10.1007/s11071-025-11269-y · Cited by 4
Dong, H., Liu, Z., Xiao-rong, H. Y., et al. (2023) · Proceedings of the Institution of Mechanical Engineers Part D Journal of Automobile Engineering · doi:10.1177/09544070231174651 · Cited by 4
Bai, B., Li, X., Guo, W. Y., et al. (2024) · Applied Sciences · doi:10.3390/app142210326 · Cited by 4
Local Calculation of Load-Dependent Gear Power Losses of Cylindrical Gears
Paschold, C., Lohner, T., & Stahl, K. (2024) · Journal of Tribology · doi:10.1115/1.4067493 · Cited by 9
Analysis of Energy Efficiency in Spur Gear Transmissions: Cycloidal Versus Involute Profiles
Fontanet, J. M. V., Salvadó, P., Català, P., et al. (2024) · Machines · doi:10.3390/machines12120943 · Cited by 4
Electrified Drive-Unit Parametric Mechanical-Loss Model Development and Calibration
Tamai, G., Palaparthy, S., Wang, B., & Ilunga, R. (2019) · SAE International Journal of Advances and Current Practices in Mobility · doi:10.4271/2019-01-1298 · Cited by 4
Laderou, A.-C., Mohammadpour, M., Theodossiades, S., Wilson, A., & Daubney, R. (2019) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/0954406219877905 · Cited by 4
“where g is the coefficient of friction which is calculated as described for the bearing case in equation (17).(41) The high loads that apply on the engaged gear teeth lead to the generation of boundary friction in addition to viscous friction.”
BackgroundDynamic Interactions Between Sliding Friction and Tip Relief in Spur Gears
He, S., & Singh, R. G. (2007) · doi:10.1115/detc2007-34077 · Cited by 4
“4 Copyright © 2007 by ASME Predicted normal load and friction force time histories (with Model III) are also validated using the benchmark friction measurements made by Rebbechi et al. [10].”
BackgroundInfluentialFrictional behaviour of engineering surfaces in overall lubrication regimes of point contacts
Wang, S., Hu, Y.-Z., & Tan, Q.-C. (2011) · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · doi:10.1177/1350650111414333 · Cited by 4
Analysis of time-varying friction excitations in helical gears with refined general formulation
Jiang, H. (2015) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/0954406215583886 · Cited by 4
Computing the power flow and mechanical efficiency of in-hub bicycle transmissions
Wu, Y.-C., & Cheng, C.-H. (2014) · Engineering Computations · doi:10.1108/ec-01-2013-0015 · Cited by 4
Dynamic characteristics of torus involute gear drive
Liu, L., & Xiong, Y. (2017) · Journal of the Brazilian Society of Mechanical Sciences and Engineering · doi:10.1007/s40430-017-0799-4 · Cited by 4
“[15] as follows: -200 -150 -100 -50 0 50”
Optimization of energy efficiency and NVH behaviour of a helical gear unit
Younes, E. B., Rigaud, E., Perret-Liaudet, J., et al. (2024) · Mechanics & Industry · doi:10.1051/meca/2023042 · Cited by 3
Metadata
- Authors
- Xu, H., Kahraman, A., Anderson, N. E., & Maddock, D. G.
- Affiliations
- The Ohio State University (US)
- General Motors (United States) (US)
- Venue
- Journal of Mechanical Design
- Publisher
- ASME International
- Published
- 2006-06-14
- Volume
- 129
- Issue
- 1
- Pages
- 58-68
- ISSN
- 0161-8458 (ISSN-L)
- 1050-0472
- 1528-9001
- OpenAlex
- W1970036055
- Semantic Scholar
- e4f46f1dbb4c333508d9b97b58992c11dcdd3355
- Cited by
- 323
- References
- 40
- Citations by year
- 2026: 22 · 2025: 31 · 2024: 28 · 2023: 23 · 2022: 25 · 2021: 26 · 2020: 23 · 2019: 15 · 2018: 20 · 2017: 13 · 2016: 12 · 2015: 17 · 2014: 19 · 2013: 11 · 2012: 9
- FWCI
- 13.71
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Journal of Mechanical Design (publishedVersion)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Gear and Bearing Dynamics Analysis
- Physical Sciences › Engineering › Mechanical Engineering › Tribology and Lubrication Engineering
- Physical Sciences › Engineering › Mechanics of Materials › Tribology and Wear Analysis
- Keywords
- parallel-axis gears, friction losses, gear load distribution, friction coefficient, elastohydrodynamic lubrication, non-Newtonian lubrication, tooth modification, lubricant properties, gear geometry
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.