Prediction of Mechanical Efficiency of Parallel-Axis Gear Pairs
The DOI matches its Crossref record; 35 of the 40 references it cites were found in a registry or an index.
Abstract
A computational model is proposed for the prediction of friction-related mechanical efficiency losses of parallel-axis gear pairs. The model incorporates a gear load distribution model, a friction model, and a mechanical efficiency formulation to predict the instantaneous mechanical efficiency of a gear pair under typical operating, surface, and lubrication conditions. The friction model uses a new friction coefficient formula obtained by using a validated non-Newtonian thermal elastohydrodynamic lubrication (EHL) model in conjunction with a multiple linear regression analysis. The load and friction coefficient distribution predictions are used to compute instantaneous torque/power losses and the mechanical efficiency of a gear pair at any given rotational position. Efficiency measurements from gear pairs having various gear designs and surface treatments are compared to model predictions. Mechanical efficiency predictions are shown to be within 0.1% of the measured values, indicating that the proposed efficiency model is accurate. Results of a parametric study are presented at the end to highlight the influence of key basic gear geometric parameters, tooth modifications, operating conditions, surface finish, and lubricant properties on mechanical efficiency losses.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Citations
Cites
Gear Geometry and Applied Theory
Litvin, F. L., & Fuentes, A. (2004) · Cambridge University Press eBooks · doi:10.1017/cbo9780511547126 · Cited by 2,332
Elasto-Hydrodynamic Lubrication
(1977) · Elsevier eBooks · doi:10.1016/c2013-0-05764-7 · Cited by 591
Applied Tribology: Bearing Design and Lubrication
Kennedy, F. E. (2002) · Journal of Tribology · doi:10.1115/1.1432665 · Cited by 325
Handbook of Practical Gear Design
Dudley, D. W. (1984) · Medical Entomology and Zoology · Cited by 286
Applied Tribology: Bearing Design and Lubrication
Khonsari, M. M., & Booser, E. R. (2017) · Wiley eBooks · doi:10.1002/9781118700280 · Cited by 235
Instantaneous Coefficients of Gear Tooth Friction
Benedict, G. H., & Kelley, B. W. (1961) · A S L E Transactions · doi:10.1080/05698196108972420 · Cited by 201
Fourth Paper: Shear Behaviour of Elastohydrodynamic Oil Films at High Rolling Contact Pressures
Johnson, K. L., & Cameron, R. (1967) · Proceedings of the Institution of Mechanical Engineers · doi:10.1243/pime_proc_1967_182_029_02 · Cited by 162
Development of a generalized mechanical efficiency prediction methodology for gear pairs
Xu, H. J. (2005) · OhioLink ETD Center (Ohio Library and Information Network) · Cited by 161
Self-citationChittenden, R. J., Dowson, D., Dunn, J. F., & Taylor, C. M. (1985) · Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences · doi:10.1098/rspa.1985.0015 · Cited by 155
Conry, T. F., & Seireg, A. (1973) · Journal of Engineering for Industry · doi:10.1115/1.3438259 · Cited by 145
Research works printed but not linked: 7
- Reuleaux, Friction in Tooth Gearing, Trans. ASME, VIII, 45
- Kelley, Lubrication of Involute Gearing, Proc. Inst. Mech. Eng., 182, 173
- Dowson, A Theory of Involute Gear Lubrication, 8
- Simon, V. , 1981, “Load Capacity and Efficiency of Spur Ears in Regard to Thermo-End Lubrication,” International Symposium on Gearing and Power Transmissions, Tokyo, Japan.
- Mihalidis, A., Bakolas, V., Panagiotidis, K., and Drivakos, N., 2002, “Prediction of the Friction Coefficient of Spur Gear Pairs,” VDI-Berichte, NR. 1665, pp. 705–719.
- Chittenden, A Theoretical Analysis of The Isothermal Elastohydrodynamic Lubricant of Concentrated Contacts, Proc. R. Soc. London, Ser. A, 397, 271
- Johnson, Shear Behavior of Elastohydrodynamic Oil Films at High Rolling Contact Pressures, Proc. Inst. Mech. Eng., 182, 307
Cited by
Items 301–320 of 320
Zhang, L., Wang, W., Chen, Q., et al. (2025) · Tribology Transactions · doi:10.1080/10402004.2025.2562569
Friction dynamics analysis of crossed beveloid gear with considering tooth surface topography
Dai, B., Ding, Y., Li, X., et al. (2025) · Advances in Mechanical Engineering · doi:10.1177/16878132251382275
“According to Xu and Kahraman, 23 the true tooth side clearance of the gear based on the W–”
Machine Learning–Based Optimization of Frictional Power Losses in Spur-Geared Transmissions
Sanoussi, N. S., Belgasam, T. M., Hammami, M., Abbès, M. S., Xue, Z., & Mande, O. (2025) · Journal of Mechanical Design · doi:10.1115/1.4070619 · Cited by 2
An Experimental Study of the Influence of Oil Flowrate on the Contact Efficiency of Gears and Discs
Handschuh, M. J., Ngo, A., Schragal, A., et al. (2026) · Lecture notes in mechanical engineering · doi:10.1007/978-981-95-3650-4_72
Self-citationZhang, T., Lin, T., Xiang, Y., et al. (2026) · Lecture notes in mechanical engineering · doi:10.1007/978-981-95-3646-7_70
Power Loss Model of 2K-V Gearbox with Anti-Backlash Beveloid Gear
Zhu, F., Song, C., Bonaiti, L., et al. (2026) · Lecture notes in mechanical engineering · doi:10.1007/978-981-95-3654-2_40
Mao, H., Ding, Y., Li, X., et al. (2026) · Scientific Reports · doi:10.1038/s41598-026-35811-z
“Figure 18 shows the time-domain response, frequency spectrum, phase plane diagram, and Poincaré section diagram of the gear system under initial wear pitting.”
Modeling of driveline dynamic efficiency and application to mass estimation
Qian, X., Tang, Y., Wang, J., Yang, K., Chen, S., Zhang, Y., Yu, X., & Liu, C. (2026) · Energy · doi:10.1016/j.energy.2026.140122
Han, H., Dong, H., Zhang, D.-B., et al. (2026) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/09544062261428655
“Xu et al. 7 expanded this model by adding a gear load distribution model, friction model, and mechanical efficiency formula to predict instantaneous mechanical efficiency under different lubrication conditions.”
Evaluation of Bending Strength and Stress Factor of Internal Asymmetric Spur Gears
Sekar, R. P. (2026) · Strength of Materials · doi:10.1007/s11223-026-00881-x
Gou, X.-F., Li, H., & Zhu, L. (2026) · Nonlinear Dynamics · doi:10.1007/s11071-026-12551-3
Mo, S., Deng, K., Gao, D., et al. (2026) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2026.114424
Mo, S., Dong, S., Fang, X., et al. (2026) · Advances in Engineering Software · doi:10.1016/j.advengsoft.2026.104223
Yang, J., Liang, D., Lin, T., et al. (2026) · Tribology International · doi:10.1016/j.triboint.2026.112336
Effect of Gear Helix Angle on Mechanical Losses in a Two-Speed I-AMT for Electric Vehicles
Ngoc, L. X., Thom, P. V., & Thái, N. H. (2026) · Mechanisms and machine science · doi:10.1007/978-3-032-29469-2_21
Tribologie als Kernkompetenz für nachhaltige Antriebstechnik
Koch, O., & Syla, S. (2026) · Springer eBooks · doi:10.1007/978-3-658-52117-2_14
Lubrication-state system-response interaction in wind turbine gear system with wear
Yu, X., Shen, Z., Sun, Y., et al. (2026) · Nonlinear Dynamics · doi:10.1007/s11071-026-12851-8
Vibration-based evaluation of dynamic efficiency for planetary gear trains
Wang, C. (2026) · Mechanical Systems and Signal Processing · doi:10.1016/j.ymssp.2026.114918
Bigerelle, M., Lemesle, J., Chevallier, E., et al. (2026) · Technologies · doi:10.3390/technologies14090586
Metadata
- Authors
- Xu, H., Kahraman, A., Anderson, N. E., & Maddock, D. G.
- Affiliations
- The Ohio State University (US)
- General Motors (United States) (US)
- Venue
- Journal of Mechanical Design
- Publisher
- ASME International
- Published
- 2006-06-14
- Volume
- 129
- Issue
- 1
- Pages
- 58-68
- ISSN
- 0161-8458 (ISSN-L)
- 1050-0472
- 1528-9001
- OpenAlex
- W1970036055
- Semantic Scholar
- e4f46f1dbb4c333508d9b97b58992c11dcdd3355
- Cited by
- 323
- References
- 40
- Citations by year
- 2026: 22 · 2025: 31 · 2024: 28 · 2023: 23 · 2022: 25 · 2021: 26 · 2020: 23 · 2019: 15 · 2018: 20 · 2017: 13 · 2016: 12 · 2015: 17 · 2014: 19 · 2013: 11 · 2012: 9
- FWCI
- 13.71
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Journal of Mechanical Design (publishedVersion)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Gear and Bearing Dynamics Analysis
- Physical Sciences › Engineering › Mechanical Engineering › Tribology and Lubrication Engineering
- Physical Sciences › Engineering › Mechanics of Materials › Tribology and Wear Analysis
- Keywords
- parallel-axis gears, friction losses, gear load distribution, friction coefficient, elastohydrodynamic lubrication, non-Newtonian lubrication, tooth modification, lubricant properties, gear geometry
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.