The DOI matches its Crossref record; 12 of the 12 references it cites were found in a registry or an index.
Effect of Particle Size Distribution on Powder Packing and Sintering in Binder Jetting Additive Manufacturing of Metals
Abstract
The binder jetting additive manufacturing (AM) process provides an economical and scalable means of fabricating complex parts from a wide variety of materials. While it is often used to fabricate metal parts, it is typically challenging to fabricate full density parts without large degree of sintering shrinkage. This can be attributed to the inherently low green density and the constraint on powder particle size imposed by challenges in recoating fine powders. To address this issue, the authors explored the use of bimodal powder mixtures in the context of binder jetting of copper. A variety of bimodal powder mixtures of various particle diameters and mixing ratios were printed and sintered to study the impact of bimodal mixtures on the parts' density and shrinkage. It was discovered that, compared to parts printed with monosized fine powders, the use of bimodal powder mixtures improves the powder's packing density (8.2%) and flowability (10.5%), and increases the sintered density (4.0%) while also reducing the sintering shrinkage (6.4%).
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Residual stresses in selective laser sintering and selective laser melting
Mercelis, P., & Kruth, J. (2006) · Rapid Prototyping Journal · doi:10.1108/13552540610707013 · Cited by 2,015
A review of process development steps for new material systems in three dimensional printing (3DP)
Utela, B., Storti, D., Anderson, R., & Ganter, M. (2008) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2009.03.002 · Cited by 548
An exploration of binder jetting of copper
Bai, Y., & Williams, C. B. (2015) · Rapid Prototyping Journal · doi:10.1108/rpj-12-2014-0180 · Cited by 270
Self-citationNovel processing of iron–manganese alloy-based biomaterials by inkjet 3-D printing
Chou, D.-T., Wells, D., Hong, D., Lee, B., Kuhn, H., & Kumta, P. N. (2013) · Acta Biomaterialia · doi:10.1016/j.actbio.2013.04.016 · Cited by 259
Fabrication of barium titanate by binder jetting additive manufacturing technology
Gaytan, S. M., Cadena, M. A., Karim, H., Delfin, D., Lin, Y., Espalin, D., MacDonald, E., & Wicker, R. B. (2015) · Ceramics International · doi:10.1016/j.ceramint.2015.01.108 · Cited by 221
Prediction of sintered density for bimodal powder mixtures
German, R. M. (1992) · Metallurgical Transactions A · doi:10.1007/bf02647329 · Cited by 183
Additive manufacturing of metallic cellular materials via three-dimensional printing
Williams, C. B., Cochran, J. K., & Rosen, D. W. (2010) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-010-2812-2 · Cited by 152
Self-citationEffects of Particle‐Size Distribution in Initial‐Stage Sintering
COBLE, R. L. (1973) · Journal of the American Ceramic Society · doi:10.1111/j.1151-2916.1973.tb12524.x · Cited by 149
Improved surface finish in 3D printing using bimodal powder distribution
Lanzetta, M., & Sachs, E. M. (2003) · Rapid Prototyping Journal · doi:10.1108/13552540310477463 · Cited by 112
Optimization of Powder Layer Density in Selective Laser Sintering
Karapatis, N. P., Egger, G., Gygax, P. E., & Glardon, R. (1999) · Infoscience (Ecole Polytechnique Fédérale de Lausanne) · doi:10.26153/tsw/746 · Cited by 112
Cited by
Binder jet 3D printing—Process parameters, materials, properties, modeling, and challenges
Mostafaei, A., Elliott, A. M., Barnes, J. E., Li, F., Tan, W., Cramer, C. L., Nandwana, P., & Chmielus, M. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100707 · Cited by 1,093
Binder jetting: A review of process, materials, and methods
Ziaee, M., & Crane, N. B. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.05.031 · Cited by 819
Chen, L.-Y., Liang, S.-X., Liu, Y., & Zhang, L.-C. (2021) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2021.100648 · Cited by 603
Mechanistic models for additive manufacturing of metallic components
Wei, H. L., Mukherjee, T., Zhang, W., Zuback, J. S., Knapp, G. L., De, A., & DebRoy, T. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100703 · Cited by 530
Metal additive manufacturing: Technology, metallurgy and modelling
Cooke, S., Ahmadi, K., Willerth, S., & Herring, R. (2020) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2020.07.025 · Cited by 378
Metadata
- Authors
- Bai, Y., Wagner, G., & Williams, C. B.
- Venue
- Journal of Manufacturing Science and Engineering
- Publisher
- ASME International
- Published
- 2017-06-01
- Volume
- 139
- Issue
- 8
- ISSN
- 1087-1357 (ISSN-L)
- 1528-8935
- OpenAlex
- W2610268762
- Cited by
- 314
- References
- 12
- FWCI
- 13.29
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effect of Particle Size Distribution on Powder Packing and Sintering in Binder Jetting Additive Manufacturing of Metals. https://app.cochat.ai/papers/10.1115/1.4036640
- The paper
- Bai, Y., Wagner, G., & Williams, C. B. (2017). Effect of Particle Size Distribution on Powder Packing and Sintering in Binder Jetting Additive Manufacturing of Metals. Journal of Manufacturing Science and Engineering. https://doi.org/10.1115/1.4036640
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.