The DOI matches its Crossref record.
Thermal Stability of Proton Conducting Acid Doped Polybenzimidazole in Simulated Fuel Cell Environments
Abstract
Recently, polybenzimidazole membrane doped with phosphoric acid (PBI) was found to have promising properties for use as a polymer electrolyte in a high temperature ( ca. 150 to 200°C) proton exchange membrane direct methanol fuel cell. However, operation at 200°C in strongly reducing and oxidizing environments introduces concerns of the thermal stability of the polymer electrolyte. To simulate the conditions in a high temperature fuel cell, PBI samples were loaded with fuel cell grade platinum black, doped with ca. 480 mole percent phosphoric acid ( i.e. , 4.8 H 3 PO 4 molecules per PBI repeat unit) and heated under atmospheres of either nitrogen, 5% hydrogen, or air in a thermal gravimetric analyzer. The products of decomposition were taken directly into a mass spectrometer for identification. In all cases weight loss below 400°C was found to be due to loss of water. Judging from the results of these tests, the thermal stability of PBI is more than adequate for use as a polymer electrolyte in a high temperature fuel cell.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
On the development of proton conducting polymer membranes for hydrogen and methanol fuel cells
Kreuer, K. D. (2001) · Journal of Membrane Science · doi:10.1016/s0376-7388(00)00632-3 · Cited by 2,969
Li, Q., He, R., Jensen, J. O., & Bjerrum, N. J. (2003) · Chemistry of Materials · doi:10.1021/cm0310519 · Cited by 1,689
Proton-conducting polymer electrolyte membranes based on hydrocarbon polymers
Rikukawa, M., & Sanui, K. (2000) · Progress in Polymer Science · doi:10.1016/s0079-6700(00)00032-0 · Cited by 1,553
High temperature proton exchange membranes based on polybenzimidazoles for fuel cells
Li, Q., Jensen, J. O., Savinell, R. F., & Bjerrum, N. J. (2009) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2008.12.003 · Cited by 1,323
Self-citationMethanol oxidation and direct methanol fuel cells: a selective review
Wasmus, S., & Küver, A. (1999) · Journal of Electroanalytical Chemistry · doi:10.1016/s0022-0728(98)00197-1 · Cited by 1,308
Self-citationSolid polymer electrolyte membranes for fuel cell applications—a review
Smitha, B., Sridhar, S., & Khan, A. A. (2005) · Journal of Membrane Science · doi:10.1016/j.memsci.2005.01.035 · Cited by 1,216
Water transport in polymer electrolyte membrane fuel cells
Jiao, K., & Li, X. (2011) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2010.06.002 · Cited by 1,086
Development of ionomer membranes for fuel cells
Kerres, J. A. (2001) · Journal of Membrane Science · doi:10.1016/s0376-7388(00)00631-1 · Cited by 1,022
A review of polymer electrolyte membranes for direct methanol fuel cells
Neburchilov, V., Martin, J., Wang, H., & Zhang, J. (2007) · Journal of Power Sources · doi:10.1016/j.jpowsour.2007.03.044 · Cited by 873
A review of the state-of-the-art of the methanol crossover in direct methanol fuel cells
Heinzel, A., & Barragán, V. M. (1999) · Journal of Power Sources · doi:10.1016/s0378-7753(99)00302-x · Cited by 816
Asensio, J. A., Sánchez, E. M., & Gómez-Romero, P. (2010) · Chemical Society Reviews · doi:10.1039/b922650h · Cited by 746
Conductivity of PBI Membranes for High-Temperature Polymer Electrolyte Fuel Cells
Ma, Y.-L., Wainright, J. S., Litt, M. H., & Savinell, R. F. (2004) · Journal of The Electrochemical Society · doi:10.1149/1.1630037 · Cited by 716
Self-citationBrønsted Acid−Base Ionic Liquids as Proton-Conducting Nonaqueous Electrolytes
Noda, A., Susan, M. A. B. H., Kudo, K., Mitsushima, S., Hayamizu, K., & Watanabe, M. (2003) · The Journal of Physical Chemistry B · doi:10.1021/jp022347p · Cited by 683
Li, Q., He, R., Jensen, J. O., & Bjerrum, N. J. (2004) · Fuel Cells · doi:10.1002/fuce.200400020 · Cited by 637
Organic–inorganic nanocomposite polymer electrolyte membranes for fuel cell applications
Tripathi, B. P., & Shahi, V. K. (2011) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2010.12.005 · Cited by 576
Proton exchange membrane fuel cell from low temperature to high temperature: Material challenges
Shao, Y., Yin, G., Wang, Z., & Gao, Y. (2007) · Journal of Power Sources · doi:10.1016/j.jpowsour.2007.02.065 · Cited by 571
Jones, D. J., & Rozière, J. (2001) · Journal of Membrane Science · doi:10.1016/s0376-7388(00)00633-5 · Cited by 568
He, R. (2003) · Journal of Membrane Science · doi:10.1016/j.memsci.2003.09.002 · Cited by 563
Design and properties of functional hybrid organic–inorganic membranes for fuel cells
Laberty-Robert, C., Vallé, K., Pereira, F., & Sanchez, C. (2011) · Chemical Society Reviews · doi:10.1039/c0cs00144a · Cited by 527
Proton conduction in acid doped polybenzimidazole
Bouchet, R. (1999) · Solid State Ionics · doi:10.1016/s0167-2738(98)00466-4 · Cited by 501
Emerging membranes for electrochemical systems
Savadogo, O. (2004) · Journal of Power Sources · doi:10.1016/j.jpowsour.2003.09.043 · Cited by 468
A comprehensive review of PBI-based high temperature PEM fuel cells
Araya, S. S., Zhou, F., Liso, V., Sahlin, S. L., Vang, J. R., Thomas, S., Gao, X., Jeppesen, C., & Kær, S. K. (2016) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2016.09.024 · Cited by 463
Polymer electrolyte membranes for the direct methanol fuel cell: A review
DeLuca, N. W., & Elabd, Y. A. (2006) · Journal of Polymer Science Part B: Polymer Physics · doi:10.1002/polb.20861 · Cited by 459
Physicochemical properties of phosphoric acid doped polybenzimidazole membranes for fuel cells
HE, R., LI, Q., BACH, A., JENSEN, J., & BJERRUM, N. (2006) · Journal of Membrane Science · doi:10.1016/j.memsci.2005.10.005 · Cited by 372
Qingfeng, L., Hjuler, H. A., & Bjerrum, N. J. (2001) · Journal of Applied Electrochemistry · doi:10.1023/a:1017558523354 · Cited by 364
Water uptake and acid doping of polybenzimidazoles as electrolyte membranes for fuel cells
Li, Q. (2004) · Solid State Ionics · doi:10.1016/j.ssi.2004.02.013 · Cited by 354
Investigation of the conduction properties of phosphoric and sulfuric acid doped polybenzimidazole
Glipa, X., Bonnet, B., Mula, B., Jones, D. J., & Rozière, J. (1999) · Journal of Materials Chemistry · doi:10.1039/a906060j · Cited by 315
Anhydrous Proton-Conducting Polymers
Schuster, M. F. H., & Meyer, W. H. (2003) · Annual Review of Materials Research · doi:10.1146/annurev.matsci.33.022702.155349 · Cited by 313
Proton‐conducting polymers based on benzimidazoles and sulfonated benzimidazoles
Asensio, J. A., Borrós, S., & Gómez‐Romero, P. (2002) · Journal of Polymer Science Part A: Polymer Chemistry · doi:10.1002/pola.10451 · Cited by 290
Asensio, J. A., & Gómez‐Romero, P. (2005) · Fuel Cells · doi:10.1002/fuce.200400081 · Cited by 274
Properties of SPEEK based PEMs for fuel cell application
Kaliaguine, S., Mikhailenko, S. D., Wang, K. P., Xing, P., Robertson, G., & Guiver, M. (2003) · Catalysis Today · doi:10.1016/s0920-5861(03)00235-9 · Cited by 269
Manea, C., & Mulder, M. (2002) · Journal of Membrane Science · doi:10.1016/s0376-7388(01)00787-6 · Cited by 263
Cross-Linked Polybenzimidazole Membranes for Fuel Cells
Li, Q., Pan, C., Jensen, J. O., Noyé, P., & Bjerrum, N. J. (2007) · Chemistry of Materials · doi:10.1021/cm0627793 · Cited by 263
Polybenzimidazole-membrane-based PEM fuel cell in the temperature range of 120–200 °C
Zhang, J., Tang, Y., Song, C., & Zhang, J. (2007) · Journal of Power Sources · doi:10.1016/j.jpowsour.2007.07.047 · Cited by 259
Deimede, V., Voyiatzis, G. A., Kallitsis, J. K., Qingfeng, L., & Bjerrum, N. J. (2000) · Macromolecules · doi:10.1021/ma000165s · Cited by 236
Asensio, J. A., Borrós, S., & Gómez-Romero, P. (2004) · Journal of The Electrochemical Society · doi:10.1149/1.1640628 · Cited by 224
High pressure electrical conductivity studies of acid doped polybenzimidazole
Fontanella, J. J., Wintersgill, M. C., Wainright, J. S., Savinell, R. F., & Litt, M. (1998) · Electrochimica Acta · doi:10.1016/s0013-4686(97)10032-9 · Cited by 165
Self-citationHasiotis, C., Qingfeng, L., Deimede, V., Kallitsis, J. K., Kontoyannis, C. G., & Bjerrum, N. J. (2001) · Journal of The Electrochemical Society · doi:10.1149/1.1366621 · Cited by 154
A thermodynamic approach to proton conductivity in acid-doped polybenzimidazole
Bouchet, R., Miller, S., Duclot, M., & Souquet, J. L. (2001) · Solid State Ionics · doi:10.1016/s0167-2738(01)00915-8 · Cited by 87
Proton Conductivity of Acid Doped Styrene‐Maleic Imide Copolymer With Benzimidazole Side Group
Pu, H., & Qiao, L. (2005) · Macromolecular Chemistry and Physics · doi:10.1002/macp.200400338 · Cited by 17
Sulfonimide Polyphosphazene-Based H[sub 2]/O[sub 2] Fuel Cells
Chalkova, E., Zhou, X., Ambler, C., Hofmann, M. A., Weston, J. A., Allcock, H. R., & Lvov, S. N. (2002) · Electrochemical and Solid-State Letters · doi:10.1149/1.1504901 · Cited by 16
Metadata
- Authors
- Samms, S. R., Wasmus, S., & Savinell, R. F.
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 1996-04-01
- Volume
- 143
- Issue
- 4
- Pages
- 1225-1232
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W2061554796
- Cited by
- 406
- References
- 0
- FWCI
- 3.40
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- iopscience.iop.org/page/copyright (vor, 8649 d)
- iopscience.iop.org/info/page/text-and-data-mining (tdm, 8649 d)
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.