The DOI matches its Crossref record.
Reporting physisorption data for gas/solid systems with special reference to the determination of surface area and porosity (Recommendations 1984)
Open accessAbstract
micropore filling.The BET method is unlikely to yield a value of the actual surface area if the isotherm is either Type I or Type III; but both Type II and Type IV isotherms are, in general, amenable to the BET analysis, provided that the value of C is neither too low nor too high and that the BET plot is linear in the region of the isotherm containing Point B.The computation of mesopore size distribution is valid only if the isotherm is of Type IV, but in view of the complexity of most pore systems little is to be gained by the application of an elaborate method of computation.If a Type I isotherm exhibits a nearly constant adsorption at high relative pressure, the micropore volume is given by the amount adsorbed at the plateau.At present there is no reliable procedure available for the computation of the micropore size distribution from a single isotherm.A check list is recommended to assist authors in the measurement of adsorption isotherms and the presentation of the data in the primary literature. CONTENTS SECTION 1.Recent work has drawn attention to the complexity of capillary condensation in pore networks and has indicated that a pore size distribution curve derived from the desorption branch of the loop is likely to be unreliable if pore blocking effects occur.It is significant that a very steep desorption branch is usually found if the lower closure point of the loop is located at the limiting p/p° (see Section 5.3).In particular, the
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“While, the adsorption capacities of the three specimens increase to a limiting value near a straight line when the relative pressures (P/P0) are extremely low, which meets the requirements of the Type I adsorption isotherms [21]”
From Modified coconut shell biochars (MCSBCs): Fabrication and their adsorptions for Pb(II) (2024) · cites this paper as [21]
Experimental — accuracy not yet measuredThe cited source says what the claim attributes to it.
In the citing paper
“Obtained pigments have an isotherm shape corresponding to types IV and V according to the IUPAC classification [63,64] (Figure 3).”
From Studies of the Morphology of Hematite Synthesized from Waste Iron Sulfate (2024) · cites this paper as [64]
The check wasn’t confident either way, so it gives no verdict — never disputed.
In the citing paper
“The IeV profile of the Mo-RF electrode in Fig. 6 show similar shape with commercial electrode performance in alkaline electrolysers as reported by Amitava [37].”
From Investigation of molybdenum-(resorcinol–formaldehyde) (Mo-RF) electrode for alkaline electrolyser operation (2011) · cites this paper as [37]
Experimental — accuracy not yet measuredThe check wasn’t confident either way, so it gives no verdict — never disputed.
In the citing paper
“The cell electrode voltage of the Mo-RF at 298 K in Table 1 are at lower ranges compared with similar IeV profile at 348 K in that report.”
From Investigation of molybdenum-(resorcinol–formaldehyde) (Mo-RF) electrode for alkaline electrolyser operation (2011) · cites this paper as [37]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Still being checked.
Cited by
Sorted by citations
Items 101–200 of 1,048
Microporous Polycarbazole with High Specific Surface Area for Gas Storage and Separation
Chen, Q., Luo, M., Hammershøj, P., Zhou, D., Han, Y. M., Laursen, B. W., Yan, C., & Han, B. (2012) · Journal of the American Chemical Society · doi:10.1021/ja300438w · Cited by 705
Optimising bioactive glass scaffolds for bone tissue engineering
Jones, J. R., Ehrenfried, L. M., & Hench, L. L. (2005) · Biomaterials · doi:10.1016/j.biomaterials.2005.07.017 · Cited by 704
Classification of Gibbs adsorption isotherms
Donohue, M. D., & Aranovich, G. L. (1998) · Advances in Colloid and Interface Science · doi:10.1016/s0001-8686(98)00044-x · Cited by 701
A historical overview of the activation and porosity of metal–organic frameworks
Zhang, X., Chen, Z., Liu, X., Hanna, S. L., Wang, X., Taheri‐Ledari, R., Maleki, A. R., Li, P., & Farha, O. K. (2020) · Chemical Society Reviews · doi:10.1039/d0cs00997k · Cited by 695
Mosher, K., He, J., Liu, Y., Rupp, E. C., & Wilcox, J. L. (2013) · International Journal of Coal Geology · doi:10.1016/j.coal.2013.01.001 · Cited by 683
Verified syntheses of mesoporous materials
Meynen, V., Cool, P., & Vansant, E. F. (2009) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2009.03.046 · Cited by 680
Li, Q., Meng, H., Zhou, P. C., Zheng, Y., Wang, J., Yu, J., & Gong, J. (2013) · ACS Catalysis · doi:10.1021/cs4000975 · Cited by 680
Monodisperse Porous LiFePO4 Microspheres for a High Power Li-Ion Battery Cathode
Sun, C., Rajasekhara, S., Goodenough, J. B., & Zhou, F. L. (2011) · Journal of the American Chemical Society · doi:10.1021/ja1110464 · Cited by 680
Nanoporous carbon for electrochemical capacitive energy storage
Shao, H., Wu, Y., Lin, Z., Taberna, P., & Simon, P. (2020) · Chemical Society Reviews · doi:10.1039/d0cs00059k · Cited by 688
Templating Mesoporous Zeolites
Egeblad, K., Christensen, C. H., Kustova, M., & Christensen, C. H. (2007) · Chemistry of Materials · doi:10.1021/cm702224p · Cited by 673
Porous Metal Oxides as Gas Sensors
Tiemann, M. (2007) · Chemistry - A European Journal · doi:10.1002/chem.200700927 · Cited by 673
Cai, Y., Liu, D., Pan, Z., Yao, Y., Li, J., & Qiu, Y. (2012) · Fuel · doi:10.1016/j.fuel.2012.06.055 · Cited by 672
Carbide‐Derived Carbons – From Porous Networks to Nanotubes and Graphene
Presser, V., Heon, M., & Gogotsi, Y. G. (2011) · Advanced Functional Materials · doi:10.1002/adfm.201002094 · Cited by 691
Synthesis Strategies of Porous Carbon for Supercapacitor Applications
Yin, J. G., Zhang, W., Alhebshi, N. A., Salah, N. A., & Alshareef, H. N. (2020) · Small Methods · doi:10.1002/smtd.201900853 · Cited by 672
Zhang, X., Zhang, L., Xie, T., & Wang, D. (2009) · The Journal of Physical Chemistry C · doi:10.1021/jp900812d · Cited by 669
New approaches to measuring biochar density and porosity
Brewer, C. E., Chuang, V. J., Masiello, C. A., Gonnermann, H., Gao, X., Dugan, B., Driver, L. E., Panzacchi, P., Zygourakis, K., & Davies, C. A. (2014) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2014.03.059 · Cited by 688
Hao, R., Wang, G., Tang, H., Sun, L., Xu, C. W., & Han, D. (2016) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2016.01.026 · Cited by 665
Characterization of activated carbon prepared by phosphoric acid activation of olive stones
Yakout, S. M., & El-Deen, G. E. S. (2011) · Arabian Journal of Chemistry · doi:10.1016/j.arabjc.2011.12.002 · Cited by 662
Zhang, S., Zhang, J., Zhang, Y., & Deng, Y. (2016) · Chemical Reviews · doi:10.1021/acs.chemrev.6b00509 · Cited by 671
Yu, J., Su, Y. R., & Cheng, B. (2007) · Advanced Functional Materials · doi:10.1002/adfm.200600933 · Cited by 665
Graphene–metal–oxide composites for the degradation of dyes under visible light irradiation
Zhang, J., Xiong, Z., & Zhao, X. (2011) · Journal of Materials Chemistry · doi:10.1039/c0jm03827j · Cited by 656
Rimola, A., Costa, D., Sodupe, M., Lambert, J., & Ugliengo, P. (2013) · Chemical Reviews · doi:10.1021/cr3003054 · Cited by 645
Review on the physicochemical treatments of rice husk for production of advanced materials
Soltani, N., Bahrami, A., Pech-Canul, M. I., & González, L. A. (2014) · Chemical Engineering Journal · doi:10.1016/j.cej.2014.11.056 · Cited by 644
Tanev, P. T., & Pinnavaia, T. J. (1996) · Chemistry of Materials · doi:10.1021/cm950549a · Cited by 644
Porous materials in catalysis: challenges for mesoporous materials
Perego, C., & Millini, R. (2012) · Chemical Society Reviews · doi:10.1039/c2cs35244c · Cited by 642
Covalent Triazine Frameworks via a Low‐Temperature Polycondensation Approach
Wang, K., Yang, L., Wang, X., Guo, L., Cheng, G., Zhang, C., Jin, S., Tan, B., & Cooper, A. I. (2017) · Angewandte Chemie International Edition · doi:10.1002/anie.201708548 · Cited by 638
Xia, P., Zhu, B., Cheng, B., Yu, J., & Xu, J. (2017) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.7b03289 · Cited by 632
Li, B., Gong, R., Wang, W., Huang, X., Zhang, W., Li, H., Hu, C., & Tan, B. (2011) · Macromolecules · doi:10.1021/ma200630s · Cited by 630
Mesoporous materials as gas sensors
Wagner, T., Haffer, S., Weinberger, C., Klaus, D., & Tiemann, M. (2012) · Chemical Society Reviews · doi:10.1039/c2cs35379b · Cited by 630
Clarkson, C. R., & Bustin, R. M. (1999) · Fuel · doi:10.1016/s0016-2361(99)00055-1 · Cited by 629
Huang, J., Sumpter, B. G., & Meunier, V. (2008) · Chemistry - A European Journal · doi:10.1002/chem.200800639 · Cited by 629
Revitalizing carbon supercapacitor electrodes with hierarchical porous structures
Liu, T., Zhang, F., Song, Y., & Li, Y. (2017) · Journal of Materials Chemistry A · doi:10.1039/c7ta05646j · Cited by 629
Origin of superhigh surface area and microcrystalline graphitic structures of activated carbons
Kaneko, K., Ishii, C., Ruike, M., & kuwabara, H. (1992) · Carbon · doi:10.1016/0008-6223(92)90139-n · Cited by 614
Yu, J., Wang, W., Cheng, B., & Su, B. (2009) · The Journal of Physical Chemistry C · doi:10.1021/jp900136q · Cited by 615
Klimakow, M., Klobes, P., Thünemann, A. F., Rademann, K., & Emmerling, F. (2010) · Chemistry of Materials · doi:10.1021/cm1012119 · Cited by 612
Theoretical Model for Nanoporous Carbon Supercapacitors
Huang, J., Sumpter, B. G., & Meunier, V. (2007) · Angewandte Chemie International Edition · doi:10.1002/anie.200703864 · Cited by 601
Bedin, K. C., Martins, A. C., Cazetta, A. L., Pezoti, O., & Almeida, V. C. (2016) · Chemical Engineering Journal · doi:10.1016/j.cej.2015.10.099 · Cited by 598
Yu, J., & Ran, J. (2011) · Energy & Environmental Science · doi:10.1039/c0ee00729c · Cited by 601
High-Pressure Adsorption Equilibria of Methane and Carbon Dioxide on Several Activated Carbons
Himeno, S., Komatsu, T., & Fujita, S. (2005) · Journal of Chemical & Engineering Data · doi:10.1021/je049786x · Cited by 596
Yu, J., Wang, G., Cheng, B., & Zhou, M. (2006) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2006.06.022 · Cited by 593
Thommes, M., Smarsly, B. M., Groenewolt, M., Ravikovitch, P. I., & Neimark, A. V. (2005) · Langmuir · doi:10.1021/la051686h · Cited by 591
Sorption thermal storage for solar energy
Yu, N., Wang, R. Z., & Wang, L. (2013) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2013.05.004 · Cited by 590
Shin, J., Samuelis, D., & Maier, J. (2011) · Advanced Functional Materials · doi:10.1002/adfm.201002527 · Cited by 587
Influence of feedstock source and pyrolysis temperature on biochar bulk and surface properties
Suliman, W., Harsh, J. B., Abu-Lail, N. I., Fortuna, A.-M., Dallmeyer, I., & Garcia-Perez, M. (2016) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2015.11.010 · Cited by 585
Li, P., Wang, X., Liu, J., Lim, J. S., Zou, R., & Zhao, Y. (2016) · Journal of the American Chemical Society · doi:10.1021/jacs.5b13335 · Cited by 585
Jiang, G., Lin, Z., Chen, C., Zhu, L., Chang, Q. H., Wang, N., Wei, W., & Tang, H. (2011) · Carbon · doi:10.1016/j.carbon.2011.02.059 · Cited by 583
Shape-Memory Nanopores Induced in Coordination Frameworks by Crystal Downsizing
Sakata, Y., Furukawa, S., Kondo, M., Hirai, K., Horike, N., Takashima, Y., Uehara, H., Louvain, N., Meilikhov, M., Tsuruoka, T., et al. (2013) · Science · doi:10.1126/science.1231451 · Cited by 580
Uddin, M. T., Nicolas, Y., Olivier, C., Toupance, T., Servant, L., Müller, M. M., Kleebe, H., Ziegler, J., & Jaegermann, W. (2012) · Inorganic Chemistry · doi:10.1021/ic300794j · Cited by 587
Wang, R., Dong, X., Du, J., Zhao, J., & Zang, S. (2017) · Advanced Materials · doi:10.1002/adma.201703711 · Cited by 578
Jiang, J., Zhang, X., Sun, P., & Zhang, L. (2011) · The Journal of Physical Chemistry C · doi:10.1021/jp205925z · Cited by 577
Porous Polymer Networks: Synthesis, Porosity, and Applications in Gas Storage/Separation
Lu, W., Yuan, D., Zhao, D., Schilling, C. I., Plietzsch, O., Müller, T., Bräse, S., Guenther, J., Blümel, J., Krishna, R., et al. (2010) · Chemistry of Materials · doi:10.1021/cm1021068 · Cited by 575
Xiong, S. L., Chen, J. S., Lou, X. W., & Zeng, H. C. (2011) · Advanced Functional Materials · doi:10.1002/adfm.201102192 · Cited by 574
Metal-free photocatalysts for hydrogen evolution
Rahman, M. Z., Kibria, M. G., & Mullins, C. B. (2020) · Chemical Society Reviews · doi:10.1039/c9cs00313d · Cited by 573
Bu, X., Tong, M., Chang, H., Kitagawa, S., & Batten, S. R. (2003) · Angewandte Chemie International Edition · doi:10.1002/anie.200352024 · Cited by 570
Removal of pharmaceutical compounds by activated carbon prepared from agricultural by-product
Baccar, R., Sarrà, M., Bouzid, J., Feki, M., & Blánquez, P. (2012) · Chemical Engineering Journal · doi:10.1016/j.cej.2012.09.099 · Cited by 568
Chemical tuning of CO2 sorption in robust nanoporous organic polymers
Dawson, R., Adams, D. J., & Cooper, A. I. (2011) · Chemical Science · doi:10.1039/c1sc00100k · Cited by 568
Jian, M., Liu, B., Zhang, G., Liu, R., & Zhang, X. (2014) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2014.10.023 · Cited by 563
Kobayashi, Y., Saito, T., & Isogai, A. (2014) · Angewandte Chemie International Edition · doi:10.1002/anie.201405123 · Cited by 566
Effect of Water Adsorption on Retention of Structure and Surface Area of Metal–Organic Frameworks
Schoenecker, P. M., Carson, C. G., Jasuja, H., Flemming, C. J. J., & Walton, K. S. (2012) · Industrial & Engineering Chemistry Research · doi:10.1021/ie202325p · Cited by 559
Groen, J. C., Peffer, L. A. A., Moulijn, J. A., & Pérez‐Ramírez, J. (2005) · Chemistry - A European Journal · doi:10.1002/chem.200500045 · Cited by 555
Porous Polymers as Multifunctional Material Platforms toward Task‐Specific Applications
Wu, J., Xu, F., Li, S., Ma, P., Zhang, X., Liu, Q., Fu, R., & Wu, D. (2018) · Advanced Materials · doi:10.1002/adma.201802922 · Cited by 561
Yu, J., Yu, J. C., Leung, M. K.-P., Ho, W., Cheng, B., Zhao, X., & Zhao, J. (2003) · Journal of Catalysis · doi:10.1016/s0021-9517(03)00034-4 · Cited by 559
Yu, J., Jin, J. G., Cheng, B., & Jaroniec, M. (2013) · Journal of Materials Chemistry A · doi:10.1039/c3ta14493c · Cited by 555
Modeling of Experimental Adsorption Isotherm Data
Chen, X. (2015) · Information · doi:10.3390/info6010014 · Cited by 550
Fang, Y., Xiao, L., Ai, X., Cao, Y., & Yang, H. (2015) · Advanced Materials · doi:10.1002/adma.201502018 · Cited by 548
Xiang, Q., Lv, K., & Yu, J. (2010) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2010.03.020 · Cited by 550
Yu, J., Wang, K., Xiao, W., & Cheng, B. (2014) · Physical Chemistry Chemical Physics · doi:10.1039/c4cp00133h · Cited by 548
Ascherl, L., Sick, T., Margraf, J. T., Lapidus, S. H., Calik, M., Hettstedt, C., Karaghiosoff, K., Döblinger, M., Clark, T., Chapman, K. W., et al. (2016) · Nature Chemistry · doi:10.1038/nchem.2444 · Cited by 544
Xu, D., Cheng, B., Cao, S., & Yu, J. (2014) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2014.09.051 · Cited by 543
Mastalerz, M., & Oppel, I. M. (2012) · Angewandte Chemie International Edition · doi:10.1002/anie.201201174 · Cited by 542
Tian, H., Pan, L., Xiao, X., Wilkins, R. W. T., Meng, Z., & Huang, B. (2013) · Marine and Petroleum Geology · doi:10.1016/j.marpetgeo.2013.07.008 · Cited by 540
Chen, L., Yang, Y., & Jiang, D. (2010) · Journal of the American Chemical Society · doi:10.1021/ja1028556 · Cited by 539
Yang, R., He, S., Yi, J., & Hu, Q. (2015) · Marine and Petroleum Geology · doi:10.1016/j.marpetgeo.2015.11.019 · Cited by 540
Peng, C., Yan, X., Wang, R., Lang, J., Ou, Y., & Xue, Q. (2012) · Electrochimica Acta · doi:10.1016/j.electacta.2012.09.082 · Cited by 538
Optimal Aluminum-Assisted Mesoporosity Development in MFI Zeolites by Desilication
Groen, J. C., Jansen, J. C., Moulijn, J. A., & Pérez‐Ramírez, J. (2004) · The Journal of Physical Chemistry B · doi:10.1021/jp047194f · Cited by 538
Carbon materials for ion-intercalation involved rechargeable battery technologies
Wang, G., Yu, M., & Feng, X. (2020) · Chemical Society Reviews · doi:10.1039/d0cs00187b · Cited by 551
Glossary of terms used in photocatalysis and radiation catalysis (IUPAC Recommendations 2011)
Braslavsky, S. E., Braun, A. M., Cassano, A. E., Emeline, A. V., Litter, M. I., Palmisano, L., Parmon, V. N., & Serpone, N. (2011) · Pure and Applied Chemistry · doi:10.1351/pac-rec-09-09-36 · Cited by 546
Rufford, T. E., Hulicova‐Jurcakova, D., Khosla, K. E., Zhu, Z., & Lu, G. Q. (2009) · Journal of Power Sources · doi:10.1016/j.jpowsour.2009.08.048 · Cited by 533
Clay mineral adsorbents for heavy metal removal from wastewater: a review
Gu, S., Kang, X., Wang, L., Lichtfouse, E. A., & Wang, C. (2018) · Environmental Chemistry Letters · doi:10.1007/s10311-018-0813-9 · Cited by 529
A Crystalline Mesoporous Coordination Copolymer with High Microporosity
Koh, K., Wong‐Foy, A. G., & Matzger, A. J. (2007) · Angewandte Chemie International Edition · doi:10.1002/anie.200705020 · Cited by 527
Controlled Multiscale Synthesis of Porous Coordination Polymer in Nano/Micro Regimes
Diring, S., Furukawa, S., Takashima, Y., Tsuruoka, T., & Kitagawa, S. (2010) · Chemistry of Materials · doi:10.1021/cm101778g · Cited by 525
High-silica zeolites for adsorption of organic micro-pollutants in water treatment: A review
Jiang, N., Shang, R., Heijman, S. G. J., & Rietveld, L. C. (2018) · Water Research · doi:10.1016/j.watres.2018.07.017 · Cited by 538
Wang, W., Serp, P., Kalck, P., & Faria, J. L. (2005) · Journal of Molecular Catalysis A Chemical · doi:10.1016/j.molcata.2005.02.027 · Cited by 521
Hydrologic properties of biochars produced at different temperatures
Kinney, T. J., Masiello, C. A., Dugan, B., Hockaday, W. C., Dean, M. R., Zygourakis, K., & Barnes, R. T. (2012) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2012.01.033 · Cited by 517
Smith, K. M., Fowler, G. D., Pullket, S., & Graham, N. J. D. (2009) · Water Research · doi:10.1016/j.watres.2009.02.038 · Cited by 517
Highly active Ni-promoted mesostructured silica nanoparticles for CO2 methanation
Aziz, M. A. A., Jalil, A. A., Triwahyono, S., Mukti, R. R., Taufiq‐Yap, Y. H., & Sazegar, M. R. (2013) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2013.09.015 · Cited by 516
Controlling ZIF-8 nano- and microcrystal formation and reactivity through zinc salt variations
Schejn, A., Balan, L., Falk, V., Aranda, L., Medjahdi, G., & Schneider, R. (2014) · CrystEngComm · doi:10.1039/c3ce42485e · Cited by 513
Yu, J., Ma, T., & Liu, S. (2010) · Physical Chemistry Chemical Physics · doi:10.1039/c0cp01139h · Cited by 513
Adsorption-Driven Heat Pumps: The Potential of Metal–Organic Frameworks
de Lange, M. F., Verouden, K. J. F. M., Vlugt, T. J. H., Gascón, J., & Kapteijn, F. (2015) · Chemical Reviews · doi:10.1021/acs.chemrev.5b00059 · Cited by 512
Mesoporous Co 3 O 4 and Au/Co 3 O 4 Catalysts for Low-Temperature Oxidation of Trace Ethylene
Yan, C., Mu, Z., Li, J., Jin, Y. G., Cheng, J., Lu, G. Q., Hao, Z., & Qiao, S. (2010) · Journal of the American Chemical Society · doi:10.1021/ja906274t · Cited by 510
Qi, G., Wang, Y., Estevez, L., Duan, X., Anako, N., Park, A. A., Li, W., Jones, C. W., & Giannelis, E. P. (2010) · Energy & Environmental Science · doi:10.1039/c0ee00213e · Cited by 509
Determination of pore size distribution in thin films by ellipsometric porosimetry
Baklanov, M. R., Mogilnikov, K. P., Polovinkin, V. G., & Dultsev, F. N. (2000) · Journal of Vacuum Science & Technology B Microelectronics and Nanometer Structures Processing Measurement and Phenomena · doi:10.1116/1.591390 · Cited by 507
Dong, F., Wang, Z., Li, Y., Ho, W., & Lee, S. (2014) · Environmental Science & Technology · doi:10.1021/es502290f · Cited by 505
Zhou, W., Sun, F., Pan, K., Tian, G., Jiang, B., Ren, Z., Tian, C., & Fu, H. (2011) · Advanced Functional Materials · doi:10.1002/adfm.201002535 · Cited by 506
One-Step Construction of Two Different Kinds of Pores in a 2D Covalent Organic Framework
Zhou, T., Xu, S., Wen, Q., Pang, Z., & Zhao, X. (2014) · Journal of the American Chemical Society · doi:10.1021/ja5092936 · Cited by 504
Lei, C., Zhu, X., Zhu, B., Jiang, C., Le, Y., & Yu, J. (2016) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2016.09.070 · Cited by 500
Porous structure dependent photoreactivity of graphitic carbon nitride under visible light
Dong, G., & Zhang, L. (2011) · Journal of Materials Chemistry · doi:10.1039/c1jm14312c · Cited by 502
Li, Y., Yin, Z., Ji, G., Liang, Z., Xue, Y., Guo, Y., Tian, J., Wang, X., & Cui, H. (2019) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2019.01.051 · Cited by 499
de Andrade, J. R., de Oliveira, M. F., da Silva, M. G. C., & Vieira, M. G. A. (2018) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.7b05137 · Cited by 502
Iglesias, D., Giuliani, A. A., Melchionna, M., Marchesan, S., Criado, A., Nasi, L., Bevilacqua, M., Tavagnacco, C., Vizza, F., Prato, M., et al. (2017) · Chem · doi:10.1016/j.chempr.2017.10.013 · Cited by 496
Metadata
- Authors
- Sing, K. S. W.
- Corresponding author
- Sing, K. S. W.
- Venue
- Pure and Applied Chemistry
- Publisher
- Walter de Gruyter GmbH
- Published
- 1985-01-01
- Volume
- 57
- Issue
- 4
- Pages
- 603-619
- ISSN
- 0033-4545 (ISSN-L)
- 1365-3075
- OpenAlex
- W1980704616
- Cited by
- 24,485
- References
- 0
- Citations by year
- 2026: 917 · 2025: 1216 · 2024: 1289 · 2023: 1250 · 2022: 1384 · 2021: 1353 · 2020: 1435 · 2019: 1478 · 2018: 1441 · 2017: 1442 · 2016: 1401 · 2015: 1319 · 2014: 1238 · 2013: 1116 · 2012: 959
- FWCI
- 16.93
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Locations
- Pure and Applied Chemistry (publishedVersion)
- Topics
- Physical Sciences › Chemistry › Physical and Theoretical Chemistry › Adsorption, diffusion, and thermodynamic properties of materials
- Physical Sciences › Materials Science › Materials Chemistry › Mesoporous Materials and Catalysis
- Physical Sciences › Chemistry › Analytical Chemistry › Analytical Chemistry and Chromatography
- Keywords
- physisorption, gas-solid systems, surface area determination, porosity determination, reporting recommendations, adsorption isotherms, BET method
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
