The DOI matches its Crossref record.
Reporting physisorption data for gas/solid systems with special reference to the determination of surface area and porosity (Recommendations 1984)
Open accessAbstract
micropore filling.The BET method is unlikely to yield a value of the actual surface area if the isotherm is either Type I or Type III; but both Type II and Type IV isotherms are, in general, amenable to the BET analysis, provided that the value of C is neither too low nor too high and that the BET plot is linear in the region of the isotherm containing Point B.The computation of mesopore size distribution is valid only if the isotherm is of Type IV, but in view of the complexity of most pore systems little is to be gained by the application of an elaborate method of computation.If a Type I isotherm exhibits a nearly constant adsorption at high relative pressure, the micropore volume is given by the amount adsorbed at the plateau.At present there is no reliable procedure available for the computation of the micropore size distribution from a single isotherm.A check list is recommended to assist authors in the measurement of adsorption isotherms and the presentation of the data in the primary literature. CONTENTS SECTION 1.Recent work has drawn attention to the complexity of capillary condensation in pore networks and has indicated that a pore size distribution curve derived from the desorption branch of the loop is likely to be unreliable if pore blocking effects occur.It is significant that a very steep desorption branch is usually found if the lower closure point of the loop is located at the limiting p/p° (see Section 5.3).In particular, the
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“While, the adsorption capacities of the three specimens increase to a limiting value near a straight line when the relative pressures (P/P0) are extremely low, which meets the requirements of the Type I adsorption isotherms [21]”
From Modified coconut shell biochars (MCSBCs): Fabrication and their adsorptions for Pb(II) (2024) · cites this paper as [21]
Experimental — accuracy not yet measuredThe cited source says what the claim attributes to it.
In the citing paper
“Obtained pigments have an isotherm shape corresponding to types IV and V according to the IUPAC classification [63,64] (Figure 3).”
From Studies of the Morphology of Hematite Synthesized from Waste Iron Sulfate (2024) · cites this paper as [64]
The check wasn’t confident either way, so it gives no verdict — never disputed.
In the citing paper
“The IeV profile of the Mo-RF electrode in Fig. 6 show similar shape with commercial electrode performance in alkaline electrolysers as reported by Amitava [37].”
From Investigation of molybdenum-(resorcinol–formaldehyde) (Mo-RF) electrode for alkaline electrolyser operation (2011) · cites this paper as [37]
Experimental — accuracy not yet measuredThe check wasn’t confident either way, so it gives no verdict — never disputed.
In the citing paper
“The cell electrode voltage of the Mo-RF at 298 K in Table 1 are at lower ranges compared with similar IeV profile at 348 K in that report.”
From Investigation of molybdenum-(resorcinol–formaldehyde) (Mo-RF) electrode for alkaline electrolyser operation (2011) · cites this paper as [37]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Still being checked.
Cited by
Sorted by citations
Items 501–600 of 1,048
Biosafety of mesoporous silica nanoparticles; towards clinical translation
Lérida‐Viso, A., Estepa‐Fernández, A., García‐Fernández, A., Martí‐Centelles, V., & Martínez‐Máñez, R. (2023) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2023.115049 · Cited by 293
Conjugated microporous poly(phenylene butadiynylene)s
Jiang, J., Su, F., Niu, H., Wood, C. D., Campbell, N. L., Khimyak, Y. Z., & Cooper, A. I. (2007) · Chemical Communications · doi:10.1039/b715563h · Cited by 287
Kim, D. S., Han, S. J., & Kwak, S. (2007) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2007.07.037 · Cited by 291
Liu, L., Hu, T., Dai, K., Zhang, J., & Liang, C. (2020) · CHINESE JOURNAL OF CATALYSIS (CHINESE VERSION) · doi:10.1016/s1872-2067(20)63560-4 · Cited by 288
Fu, K., Yue, Q., Gao, B., Sun, Y., & Zhu, L. (2013) · Chemical Engineering Journal · doi:10.1016/j.cej.2013.05.028 · Cited by 285
Xiang, Q., Cheng, F., & Lang, D. (2016) · ChemSusChem · doi:10.1002/cssc.201501702 · Cited by 286
Water adsorption in UiO-66: the importance of defects
Ghosh, P., Colón, Y. J., & Snurr, R. Q. (2014) · Chemical Communications · doi:10.1039/c4cc04945d · Cited by 284
Mesoporous anhydrous RuO2 as a supercapacitor electrode material
SUBRAMANIAN, V. (2004) · Solid State Ionics · doi:10.1016/j.ssi.2004.01.070 · Cited by 284
Superhigh surface area determination of microporous solids
Kaneko, K., & Ishii, C. (1992) · Colloids and Surfaces · doi:10.1016/0166-6622(92)80299-h · Cited by 284
Tan, Y. H., Davis, J. A., Fujikawa, K., Ganesh, N. V., Demchenko, A. V., & Stine, K. J. (2012) · Journal of Materials Chemistry · doi:10.1039/c2jm16633j · Cited by 285
Zhang, Z., Jiang, D., Li, D., He, M., & Chen, M. (2015) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2015.10.022 · Cited by 286
Porous structure and surface chemistry of phosphoric acid activated carbon from corncob
Sych, N. V., Trofymenko, S. I., Poddubnaya, O. I., Tsyba, N. N., Sapsay, V. I., Klymchuk, D. O., & Puziy, A. M. (2012) · Applied Surface Science · doi:10.1016/j.apsusc.2012.07.084 · Cited by 283
Influence of Size on the Rate of Mesoporous Electrodes for Lithium Batteries
Ren, Y., Armstrong, A. R., Jiao, F., & Bruce, P. G. (2009) · Journal of the American Chemical Society · doi:10.1021/ja905488x · Cited by 283
Room temperature growth of mesoporous silica fibers: A new high‐surface‐area optical waveguide
Huo, Q., Zhao, D., Feng, J., Weston, K. D., Buratto, S. K., Stucky, G. D., Schacht, S., & Schüth, F. (1997) · Advanced Materials · doi:10.1002/adma.19970091210 · Cited by 281
Naderi, M. (2014) · Elsevier eBooks · doi:10.1016/b978-0-12-384746-1.00014-8 · Cited by 281
Liu, B., Liu, L., Lang, X.-F., Wang, H., Lou, X. W., & Aydil, E. S. (2014) · Energy & Environmental Science · doi:10.1039/c4ee00472h · Cited by 283
Li, Y., Zhang, C., Tang, D., Gan, Q., Niu, X., Wang, K., & Shen, R. (2017) · Fuel · doi:10.1016/j.fuel.2017.06.028 · Cited by 281
Chen, J., Chen, X., Xu, W., Xu, Z., Chen, J., Jia, H., & Chen, J. (2017) · Chemical Engineering Journal · doi:10.1016/j.cej.2017.07.147 · Cited by 281
Jeremias, F., Lozan, V., Henninger, S. K., & Janiak, C. (2013) · Dalton Transactions · doi:10.1039/c3dt51471d · Cited by 280
Shin, E. W., Han, J. S., Jang, M., Min, S., Park, J. K., & Rowell, R. M. (2003) · Environmental Science & Technology · doi:10.1021/es030488e · Cited by 284
Mesoporosity as a new parameter for understanding tension stress generation in trees
Chang, S., Clair, B., Ruelle, J., Beauchêne, J., Renzo, F. D., Quignard, F., Zhao, G., Yamamoto, H., & Gril, J. (2009) · Journal of Experimental Botany · doi:10.1093/jxb/erp133 · Cited by 280
Toward Superior Capacitive Energy Storage: Recent Advances in Pore Engineering for Dense Electrodes
Liu, C., Yan, X., Hu, F., Gao, G., Wu, G., & Yang, X. (2018) · Advanced Materials · doi:10.1002/adma.201705713 · Cited by 284
Xiao, X., Xing, C., He, G., Zuo, X., Nan, J., & Wang, L. (2013) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2013.10.055 · Cited by 279
Sustainable production of acrolein: Gas-phase dehydration of glycerol over Nb2O5 catalyst
Chai, S., Wang, H., LIANG, Y., & Xu, B. (2007) · Journal of Catalysis · doi:10.1016/j.jcat.2007.06.016 · Cited by 279
Tailoring Surface and Structural Properties of MCM-41 Silicas by Bonding Organosilanes
Jaroniec, C. P., Kruk, M., Jaroniec, M., & Sayari, A. (1998) · The Journal of Physical Chemistry B · doi:10.1021/jp981304z · Cited by 279
Chung, S., Han, P., Singhal, R., Kalra, V., & Manthiram, A. (2015) · Advanced Energy Materials · doi:10.1002/aenm.201500738 · Cited by 282
Jiang, X., Guo, Y., Zhang, L., Jiang, W., & Xie, R. (2018) · Chemical Engineering Journal · doi:10.1016/j.cej.2018.02.034 · Cited by 279
Yao, X., Xiong, Y., Zou, W., Zhang, L., Wu, S., Dong, X., Gao, F., Deng, Y., Tang, C., Chen, Z., et al. (2013) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2013.06.020 · Cited by 277
Nitrogen-Doped Yolk–Shell-Structured CoSe/C Dodecahedra for High-Performance Sodium Ion Batteries
Zhang, Y., Pan, A., Ding, L., Zhou, Z., Wang, Y., Niu, S., Liang, S., & Cao, G. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b13153 · Cited by 277
Highly selective CO2 capture by S-doped microporous carbon materials
Seema, H., Kemp, K. C., Le, N. H., Park, S., Chandra, V., Lee, J. W., & Kim, K. S. (2013) · Carbon · doi:10.1016/j.carbon.2013.09.006 · Cited by 276
Depçi, T., Kul, A. R., & Önal, Y. (2012) · Chemical Engineering Journal · doi:10.1016/j.cej.2012.06.077 · Cited by 276
Boosting the supercapacitor performances of activated carbon with carbon nanomaterials
Cheng, F. J., Yang, X., Zhang, S., & Lu, W. J. (2020) · Journal of Power Sources · doi:10.1016/j.jpowsour.2019.227678 · Cited by 276
Properties of halloysite nanotube–epoxy resin hybrids and the interfacial reactions in the systems
Liu, M., Guo, B., Du, M., Cai, X., & Jia, D. (2007) · Nanotechnology · doi:10.1088/0957-4484/18/45/455703 · Cited by 275
Schejn, A., Aboulaich, A., Balan, L., Falk, V., Lalevée, J., Medjahdi, G., Aranda, L., Mozet, K., & Schneider, R. (2014) · Catalysis Science & Technology · doi:10.1039/c4cy01505c · Cited by 275
Xu, J., Wang, G., Fan, J., Liu, B., Cao, S., & Yu, J. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.10.033 · Cited by 275
Yin, Z.-J., Xu, S., Zhan, T., Qi, Q.-Y., Wu, Z., & Zhao, X. (2017) · Chemical Communications · doi:10.1039/c7cc01045a · Cited by 275
Saha, D., & Kienbaum, M. J. (2019) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2019.05.051 · Cited by 279
Tantirungrotechai, J., & Tilley, T. D. (2002) · Journal of the American Chemical Society · doi:10.1021/ja0202208 · Cited by 274
Zheng, X., Lin, H., Zheng, J., Duan, X., & Yuan, Y. (2013) · ACS Catalysis · doi:10.1021/cs400574v · Cited by 273
Low, J., Yu, J., Li, Q., & Cheng, B. (2013) · Physical Chemistry Chemical Physics · doi:10.1039/c3cp53820f · Cited by 275
Nanostructure evolution and calcium distribution in sol–gel derived bioactive glass
Lin, S., Ionescu, C., Pike, K. J., Smith, M. E., & Jones, J. R. (2009) · Journal of Materials Chemistry · doi:10.1039/b814292k · Cited by 273
Chen, H., He, J., Zhang, C., & He, H. (2007) · The Journal of Physical Chemistry C · doi:10.1021/jp076113n · Cited by 273
Current status and future prospects of nanotechnology in cosmetics
Mihranyan, A., Ferraz, N., & Strømme, M. (2011) · Progress in Materials Science · doi:10.1016/j.pmatsci.2011.10.001 · Cited by 272
Influence of one-step and two-step KOH activation on activated carbon characteristics
Oginni, O. J., Singh, K., Oporto, G. S., Dawson-Andoh, B. E., McDonald, L. M., & Sabolsky, E. M. (2019) · Bioresource Technology Reports · doi:10.1016/j.biteb.2019.100266 · Cited by 272
Xiang, Q., Cheng, B., & Yu, J. (2013) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2013.03.005 · Cited by 271
Nitrogen Adsorption Studies of Novel Synthetic Active Carbons
Kruk, M., Jaroniec, M., & Gadkaree, K. P. (1997) · Journal of Colloid and Interface Science · doi:10.1006/jcis.1997.5009 · Cited by 271
Characteristics of activated carbon from peanut hulls in relation to conditions of preparation
Girgis, B. S., Yunis, S. S., & Soliman, A. M. (2002) · Materials Letters · doi:10.1016/s0167-577x(02)00724-3 · Cited by 271
Design and synthesis of polyoxometalate-framework materials from cluster precursors
Vilà‐Nadal, L., & Cronin, L. (2017) · Nature Reviews Materials · doi:10.1038/natrevmats.2017.54 · Cited by 271
Dai, Z., Zhen, Y., Sun, Y., Li, L., & Ding, D. (2021) · Chemical Engineering Journal · doi:10.1016/j.cej.2021.129002 · Cited by 271
Physisorption of argon, nitrogen and oxygen by MCM-41, a model mesoporous adsorbent
Branton, P. J., Hall, P. G., Sing, K. S. W., Reichert, H., Schüth, F., & Unger, K. K. (1994) · Journal of the Chemical Society Faraday Transactions · doi:10.1039/ft9949002965 · Cited by 271
Self-citationCoordination polymers and metal–organic frameworks based on poly(pyrazole)-containing ligands
Pettinari, C., Tăbăcaru, A., & Galli, S. (2015) · Coordination Chemistry Reviews · doi:10.1016/j.ccr.2015.08.005 · Cited by 270
Yang, W., Gao, Z. J., Wang, J., Ma, J., Zhang, M., & Liu, L. (2013) · ACS Applied Materials & Interfaces · doi:10.1021/am4003843 · Cited by 270
Adsorption of cationic dyes onto mesoporous silica
Huang, C., Chang, K.-P., Ou, H.-D., Chiang, Y., & Wang, C. (2010) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2010.11.002 · Cited by 270
Xie, J., Shevlin, S. A., Ruan, Q., Moniz, S. J. A., Liu, Y., Liu, X., Li, Y., Lau, C. C., Guo, Z., & Tang, J. (2018) · Energy & Environmental Science · doi:10.1039/c7ee02981k · Cited by 270
Recent Advances and Future Aspects in the Selective Isomerization of High n‐Alkanes
Akhmedov, V. M., & Al‐Khowaiter, S. H. (2007) · Catalysis Reviews · doi:10.1080/01614940601128427 · Cited by 269
Wei, J., Sun, J. Q., Wen, Z., Fang, C., Ge, Q., & Xu, H. (2016) · Catalysis Science & Technology · doi:10.1039/c6cy00160b · Cited by 271
Pore characterization and its impact on methane adsorption capacity for organic-rich marine shales
Wang, Y., Zhu, Y., Liu, S., & Zhang, R. (2016) · Fuel · doi:10.1016/j.fuel.2016.04.082 · Cited by 269
Carbonation of hardened cement pastes: Influence of temperature
Drouet, E., Poyet, S., Le Bescop, P., Torrenti, J.-M., & Bourbon, X. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.09.019 · Cited by 265
Microporous Functionalized Triazine-Based Polyimides with High CO 2 Capture Capacity
Liebl, M., & Senker, J. (2013) · Chemistry of Materials · doi:10.1021/cm4000894 · Cited by 268
Luo, Y., Jiang, J., Zhou, W., Yang, H., Luo, J., Qi, X., Zhang, H., Yu, D. Y. W., Li, C. M., & Yu, T. (2012) · Journal of Materials Chemistry · doi:10.1039/c2jm16419a · Cited by 268
Hug, S., Stegbauer, L., Oh, H., Hirscher, M., & Lotsch, B. V. (2015) · Chemistry of Materials · doi:10.1021/acs.chemmater.5b03330 · Cited by 269
Fang, Y., Xiao, L., Qian, J., Ai, X., Yang, H., & Cao, Y. (2014) · Nano Letters · doi:10.1021/nl501152f · Cited by 268
Wang, X. P., & Lim, T. (2010) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2010.08.012 · Cited by 267
Anwander, R., Runte, O., Eppinger, J., Gerstberger, G., Herdtweck, E., & Spiegler, M. (1998) · Journal of the Chemical Society Dalton Transactions · doi:10.1039/a705608g · Cited by 270
Newalkar, B. L., Olanrewaju, J., & Komarneni, S. (2001) · Chemistry of Materials · doi:10.1021/cm000748g · Cited by 267
Silva, T. L., Ronix, A., Pezoti, O., Spessato, L., Leandro, P. K. T., Bedin, K. C., Beltrame, K. K., Cazetta, A. L., & Almeida, V. C. (2016) · Chemical Engineering Journal · doi:10.1016/j.cej.2016.06.009 · Cited by 267
Micelle-templated silicates as a test bed for methods of mesopore size evaluation
Galarneau, A., Desplantier‐Giscard, D., Dutartre, R., & Renzo, F. D. (1999) · Microporous and Mesoporous Materials · doi:10.1016/s1387-1811(98)00263-7 · Cited by 267
Antibacterial activity of montmorillonites modified with silver
Magaña, S. M., Quintana, P., Aguilar, D. H., Toledo-Antonio, J. A., Ángeles–Chávez, C., Cortés-Jácome, M. A., León-Deniz, L. V., Freile‐Pelegrín, Y., López, T., & Sánchez, R. M. T. (2007) · Journal of Molecular Catalysis A Chemical · doi:10.1016/j.molcata.2007.10.024 · Cited by 266
Do, M. H., Phan, N. H., Nguyễn, T. D., Pham, T. T. S., Nguyen, V. K., Vu, T. T. T., & Nguyen, T. K. P. (2011) · Chemosphere · doi:10.1016/j.chemosphere.2011.07.023 · Cited by 266
Highly Pure Silica Nanoparticles with High Adsorption Capacity Obtained from Sugarcane Waste Ash
Rovani, S., dos Santos, J. J., Cório, P., & Fungaro, D. A. (2018) · ACS Omega · doi:10.1021/acsomega.8b00092 · Cited by 266
Li, Y., Wang, Z., Pan, Z., Niu, X., Yu, Y., & Meng, S. (2018) · Fuel · doi:10.1016/j.fuel.2018.12.066 · Cited by 266
He, Y., Zhang, L., Xiao, A., Wan, G., Zhu, W., & Luo, Y. (2019) · The Science of The Total Environment · doi:10.1016/j.scitotenv.2019.06.175 · Cited by 267
Modeling of Adsorption and Desorption in Pores of Simple Geometry Using Molecular Dynamics
Sarkisov, L., & Monson, P. A. (2001) · Langmuir · doi:10.1021/la015521u · Cited by 267
Zhang, Y.-J., Xing, Z., Duan, Z., Li, M., & Wang, Y. (2014) · Applied Surface Science · doi:10.1016/j.apsusc.2014.07.126 · Cited by 265
Synthesis and Li-Ion Insertion Properties of Highly Crystalline Mesoporous Rutile TiO2
Wang, D., Choi, D., Yang, Z. G., Viswanathan, V., Nie, Z., Wang, C., Song, Y., Zhang, J., & Liu, J. (2008) · Chemistry of Materials · doi:10.1021/cm8002589 · Cited by 264
Chen, H., & He, J. (2008) · The Journal of Physical Chemistry C · doi:10.1021/jp806160g · Cited by 264
Investigation on Fe-Co binary metal oxides supported on activated semi-coke for NO reduction by CO
Wang, L., Cheng, X., Wang, Z., Ma, C., & Qin, Y. (2016) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2016.08.021 · Cited by 264
Removal of cadmium and lead ions from water by sulfonated magnetic nanoparticle adsorbents
Chen, K., He, J., Li, Y., Cai, X., Zhang, K., Liu, T., Hu, Y., Lin, D., Kong, L., & Liu, J. (2017) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2017.01.082 · Cited by 264
Wang, Z., Yang, X., Yang, T., Zhao, Y., Wang, F., Chen, Y., Zeng, J., Yan, C., Huang, F., & Jiang, J. (2018) · ACS Catalysis · doi:10.1021/acscatal.8b02607 · Cited by 264
Luo, J., Li, R., Chen, Y., Zhou, X., Ning, X., Zhan, L., Ma, L., Xu, X., Xu, L., & Zhang, L. (2018) · Separation and Purification Technology · doi:10.1016/j.seppur.2018.08.028 · Cited by 264
Kwon, H. J., Hwang, J., Shin, H., Jeong, M., Chung, K. Y., Sun, Y., & Jung, H. (2019) · Nano Letters · doi:10.1021/acs.nanolett.9b04395 · Cited by 270
Leghari, S. A. K., Sajjad, S., Chen, F., & Zhang, J. (2010) · Chemical Engineering Journal · doi:10.1016/j.cej.2010.11.065 · Cited by 263
Preparation of activated carbons from Spanish anthracite
Lillo-Ródenas, M. A., Lozano‐Castelló, D., Cazorla‐Amorós, D., & Linares-Solano, A. (2001) · Carbon · doi:10.1016/s0008-6223(00)00186-x · Cited by 263
Characterization of MCM-41 Using Molecular Simulation: Heterogeneity Effects
Maddox, M. W., Olivier, J. P., & Gubbins, K. E. (1997) · Langmuir · doi:10.1021/la961068o · Cited by 263
Mesoporous high-surface-area activated carbon
Hu, Z., & Srinivasan, M. (2001) · Microporous and Mesoporous Materials · doi:10.1016/s1387-1811(00)00355-3 · Cited by 262
Dai, F., Zai, J., Yi, R., Gordin, M. L., Sohn, H., Chen, S., & Wang, D. (2014) · Nature Communications · doi:10.1038/ncomms4605 · Cited by 266
Seema, H., Kemp, K. C., Chandra, V., & Kim, K. S. (2012) · Nanotechnology · doi:10.1088/0957-4484/23/35/355705 · Cited by 261
Comparison of the hygric behaviour of three hemp concretes
Collet, F., Chamoin, J., Prétot, S., & Lanos, C. (2013) · Energy and Buildings · doi:10.1016/j.enbuild.2013.03.010 · Cited by 261
Direct Synthesis of Al−SBA-15 Mesoporous Materials via Hydrolysis-Controlled Approach
Li, Y., Zhang, W., Zhang, L., Yang, Q., Wei, Z., Feng, Z., & Li, C. (2004) · The Journal of Physical Chemistry B · doi:10.1021/jp049824j · Cited by 261
Pezoti, O., Cazetta, A. L., Souza, I. P. A. F., Bedin, K. C., Martins, A. C., Silva, T. L., & Almeida, V. C. (2014) · Journal of Industrial and Engineering Chemistry · doi:10.1016/j.jiec.2014.02.007 · Cited by 261
Hydrogen storage in activated carbon materials: Role of the nanoporous texture
Texier-Mandoki, N., Dentzer, J., Piquero, T., Saadallah, S.-E., David, P., & Vix‐Guterl, C. (2004) · Carbon · doi:10.1016/j.carbon.2004.05.018 · Cited by 261
Adsorption, intrusion and freezing in porous silica: the view from the nanoscale
Coasne, B., Galarneau, A., Pellenq, R. J. ‐., & Renzo, F. D. (2013) · Chemical Society Reviews · doi:10.1039/c2cs35384a · Cited by 260
Mellaerts, R., Jammaer, J. A. G., Speybroeck, M. V., Chen, H., Humbeeck, J. V., Augustijns, P., den Mooter, G. V., & Martens, J. A. (2008) · Langmuir · doi:10.1021/la801161g · Cited by 260
Wang, C., Zhang, H., Li, F., & Zhu, L. Y. (2010) · Environmental Science & Technology · doi:10.1021/es101890w · Cited by 261
Porous boron nitride with a high surface area: hydrogen storage and water treatment
Li, J., Lin, J., Xu, X., Zhang, X., Xue, Y., Mi, J., Mo, Z., Fan, Y., Hu, L., Yang, X., et al. (2013) · Nanotechnology · doi:10.1088/0957-4484/24/15/155603 · Cited by 262
Saravanapavan, P., Jones, J. R., Pryce, R. S., & Hench, L. L. (2003) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.10532 · Cited by 259
Xu, F., Zhang, L., Cheng, B., & Yu, J. (2018) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.8b02710 · Cited by 259
Schütter, C., Pohlmann, S., & Balducci, A. (2019) · Advanced Energy Materials · doi:10.1002/aenm.201900334 · Cited by 259
Hu, T., Pang, X., Jiang, F., Wang, Q., Liu, X., Wang, Z., Jiang, S. Y., Wu, G., Li, C., Xu, T., et al. (2021) · Earth-Science Reviews · doi:10.1016/j.earscirev.2021.103545 · Cited by 259
Metadata
- Authors
- Sing, K. S. W.
- Corresponding author
- Sing, K. S. W.
- Venue
- Pure and Applied Chemistry
- Publisher
- Walter de Gruyter GmbH
- Published
- 1985-01-01
- Volume
- 57
- Issue
- 4
- Pages
- 603-619
- ISSN
- 0033-4545 (ISSN-L)
- 1365-3075
- OpenAlex
- W1980704616
- Cited by
- 24,485
- References
- 0
- Citations by year
- 2026: 917 · 2025: 1216 · 2024: 1289 · 2023: 1250 · 2022: 1384 · 2021: 1353 · 2020: 1435 · 2019: 1478 · 2018: 1441 · 2017: 1442 · 2016: 1401 · 2015: 1319 · 2014: 1238 · 2013: 1116 · 2012: 959
- FWCI
- 16.93
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Locations
- Pure and Applied Chemistry (publishedVersion)
- Topics
- Physical Sciences › Chemistry › Physical and Theoretical Chemistry › Adsorption, diffusion, and thermodynamic properties of materials
- Physical Sciences › Materials Science › Materials Chemistry › Mesoporous Materials and Catalysis
- Physical Sciences › Chemistry › Analytical Chemistry › Analytical Chemistry and Chromatography
- Keywords
- physisorption, gas-solid systems, surface area determination, porosity determination, reporting recommendations, adsorption isotherms, BET method
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
