The DOI matches its Crossref record.
Reporting physisorption data for gas/solid systems with special reference to the determination of surface area and porosity (Recommendations 1984)
Open accessAbstract
micropore filling.The BET method is unlikely to yield a value of the actual surface area if the isotherm is either Type I or Type III; but both Type II and Type IV isotherms are, in general, amenable to the BET analysis, provided that the value of C is neither too low nor too high and that the BET plot is linear in the region of the isotherm containing Point B.The computation of mesopore size distribution is valid only if the isotherm is of Type IV, but in view of the complexity of most pore systems little is to be gained by the application of an elaborate method of computation.If a Type I isotherm exhibits a nearly constant adsorption at high relative pressure, the micropore volume is given by the amount adsorbed at the plateau.At present there is no reliable procedure available for the computation of the micropore size distribution from a single isotherm.A check list is recommended to assist authors in the measurement of adsorption isotherms and the presentation of the data in the primary literature. CONTENTS SECTION 1.Recent work has drawn attention to the complexity of capillary condensation in pore networks and has indicated that a pore size distribution curve derived from the desorption branch of the loop is likely to be unreliable if pore blocking effects occur.It is significant that a very steep desorption branch is usually found if the lower closure point of the loop is located at the limiting p/p° (see Section 5.3).In particular, the
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“While, the adsorption capacities of the three specimens increase to a limiting value near a straight line when the relative pressures (P/P0) are extremely low, which meets the requirements of the Type I adsorption isotherms [21]”
From Modified coconut shell biochars (MCSBCs): Fabrication and their adsorptions for Pb(II) (2024) · cites this paper as [21]
Experimental — accuracy not yet measuredThe cited source says what the claim attributes to it.
In the citing paper
“Obtained pigments have an isotherm shape corresponding to types IV and V according to the IUPAC classification [63,64] (Figure 3).”
From Studies of the Morphology of Hematite Synthesized from Waste Iron Sulfate (2024) · cites this paper as [64]
The check wasn’t confident either way, so it gives no verdict — never disputed.
In the citing paper
“The IeV profile of the Mo-RF electrode in Fig. 6 show similar shape with commercial electrode performance in alkaline electrolysers as reported by Amitava [37].”
From Investigation of molybdenum-(resorcinol–formaldehyde) (Mo-RF) electrode for alkaline electrolyser operation (2011) · cites this paper as [37]
Experimental — accuracy not yet measuredThe check wasn’t confident either way, so it gives no verdict — never disputed.
In the citing paper
“The cell electrode voltage of the Mo-RF at 298 K in Table 1 are at lower ranges compared with similar IeV profile at 348 K in that report.”
From Investigation of molybdenum-(resorcinol–formaldehyde) (Mo-RF) electrode for alkaline electrolyser operation (2011) · cites this paper as [37]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Still being checked.
Cited by
Sorted by citations
Items 801–900 of 1,048
Blanco, S. P. D. M., Scheufele, F. B., Módenes, A. N., Espinoza‐Quiñones, F. R., Marin, P., Kroumov, A. D., & Borba, C. E. (2016) · Chemical Engineering Journal · doi:10.1016/j.cej.2016.08.104 · Cited by 215
Li, Q., Xia, Y., Yang, C., Lv, K., Lei, M., & Li, M. (2018) · Chemical Engineering Journal · doi:10.1016/j.cej.2018.05.094 · Cited by 215
Jiang, X., Gong, H., Liu, Q., Song, M., & Huang, C. (2019) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2019.118439 · Cited by 215
1D/2D TiO2/ZnIn2S4 S-scheme heterojunction photocatalyst for efficient hydrogen evolution
Li, J., Wu, C., Li, J., Dong, B., Zhao, L., & Wang, S. (2022) · CHINESE JOURNAL OF CATALYSIS (CHINESE VERSION) · doi:10.1016/s1872-2067(21)63875-5 · Cited by 215
Review and the state of the art: Sol–gel and melt quenched bioactive glasses for tissue engineering
Kaur, G., Pickrell, G., Sriranganathan, N., Kumar, V. R., & Homa, D. (2015) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.33443 · Cited by 214
High‐Performance Supercapacitor Electrode Materials Prepared from Various Pollens
Zhang, L., Zhang, F., Yang, X., Leng, K., Huang, Y., & Chen, Y. (2013) · Small · doi:10.1002/smll.201202943 · Cited by 214
Zhang, J., Liu, S., Yu, J., & Jaroniec, M. (2011) · Journal of Materials Chemistry · doi:10.1039/c1jm12596f · Cited by 214
Spontaneous Functionalization of Carbon Black by Reaction with 4-Nitrophenyldiazonium Cations
Toupin, M., & Bélanger, D. (2008) · Langmuir · doi:10.1021/la702556n · Cited by 214
Choi, H. J., Dincă, M., Dailly, A., & Long, J. R. (2009) · Energy & Environmental Science · doi:10.1039/b917512a · Cited by 214
Surface functionality and porosity of activated carbons obtained from chemical activation of wood
Benaddi, H., Bandosz, T. J., Jagiełło, J., Schwarz, J. A., Rouzaud, J., Legras, D., & Béguin, F. (2000) · Carbon · doi:10.1016/s0008-6223(99)00134-7 · Cited by 214
Hunt, A. G., & Sahimi, M. (2017) · Reviews of Geophysics · doi:10.1002/2017rg000558 · Cited by 214
Karmakar, S., Barman, S., Rahimi, F. A., Rambabu, D., Nath, S., & Maji, T. K. (2023) · Nature Communications · doi:10.1038/s41467-023-40117-z · Cited by 215
Elimination of organic water pollutants using adsorbents obtained from sewage sludge
Otero, M., Rozada, F., Calvo, L. F., García, A. I., & Morán, A. (2003) · Dyes and Pigments · doi:10.1016/s0143-7208(03)00005-6 · Cited by 213
Fan, Z., Meng, F., Zhang, M., Wu, Z., Sun, Z., & Li, A. (2015) · Applied Surface Science · doi:10.1016/j.apsusc.2015.11.021 · Cited by 213
Wang, Z., Chen, M., Huang, Y. H., Shi, X., Zhang, Y., Huang, T., Cao, J., Ho, W., & Lee, S. C. (2018) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2018.08.030 · Cited by 213
Mohammad, A.-T., Abdulhameed, A. S., & Jawad, A. H. (2019) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2019.02.025 · Cited by 213
Bergaoui, M., Khalfaoui, M., Awadallah‐F, A., & Al‐Muhtaseb, S. A. (2021) · Journal of Natural Gas Science and Engineering · doi:10.1016/j.jngse.2021.104289 · Cited by 213
Fractal characteristics of Upper Cretaceous lacustrine shale from the Songliao Basin, NE China
Wang, M., Xue, H., Tian, S., Wilkins, R. W. T., & Wang, Z. (2015) · Marine and Petroleum Geology · doi:10.1016/j.marpetgeo.2015.05.011 · Cited by 213
Monolayer–multilayer adsorption phenomenological model: Kinetics, equilibrium and thermodynamics
Scheufele, F. B., Módenes, A. N., Borba, C. E., Ribeiro, C., Espinoza‐Quiñones, F. R., Bergamasco, R., & Pereira, N. C. (2015) · Chemical Engineering Journal · doi:10.1016/j.cej.2015.09.085 · Cited by 212
Yu, J., Yue, L., Liu, S., Huang, B., & Zhang, X. (2009) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2009.03.034 · Cited by 212
Porous structure and water vapour sorption of hemp-based materials
Collet, F., Bart, M., Serres, L., & Miriel, J. (2007) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2007.01.018 · Cited by 212
Large scale production of biomass-derived nitrogen-doped porous carbon materials for supercapacitors
Wei, T., Wei, X., Gao, Y. L., & Li, H. (2015) · Electrochimica Acta · doi:10.1016/j.electacta.2015.04.082 · Cited by 213
Dong, H., Yu, H., & Wang, X. (2012) · Environmental Science & Technology · doi:10.1021/es303619a · Cited by 212
The role of H 3 PO 4 in the preparation of activated carbon from NaOH-treated rice husk residue
Li, Y., Xian, Z., Yang, R., Li, G., & Hu, C. (2015) · RSC Advances · doi:10.1039/c5ra04634c · Cited by 212
Zhang, N., Yang, M., Tang, Z., & Xu, Y. (2013) · Journal of Catalysis · doi:10.1016/j.jcat.2013.02.026 · Cited by 212
Synthesis and characterization of geopolymers derived from coal gangue, fly ash and red mud
Koshy, N., Dondrob, K., Hu, L., Wen, Q., & Meegoda, J. N. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.02.076 · Cited by 212
Zhang, P., Tan, X., Liu, S., Liu, Y., Zeng, G., Ye, S., Yin, Z., Hu, X., & Liu, N. (2019) · Chemical Engineering Journal · doi:10.1016/j.cej.2019.122141 · Cited by 212
SnO-SnO2 modified two-dimensional MXene Ti3C2T for acetone gas sensor working at room temperature
Wang, Z., Wang, F., Hermawan, A., Asakura, Y., Hasegawa, T., Kumagai, H., Kato, H., Kakihana, M., Zhu, J., & Yin, S. (2020) · Journal of Material Science and Technology · doi:10.1016/j.jmst.2020.07.040 · Cited by 212
A simple template-free approach to TiO2 hollow spheres with enhanced photocatalytic activity
Yu, J., & Zhang, J. (2010) · Dalton Transactions · doi:10.1039/c0dt00053a · Cited by 211
Chen, F., Zhang, L., Chen, Q., Zhang, Y., & Zhang, Z. (2010) · Chemical Communications · doi:10.1039/c0cc02577a · Cited by 211
Properties improvement of fly ash cenosphere modified cement pastes using nano silica
Hanif, A., Parthasarathy, P., Ma, H., Fan, T., & Li, Z. (2017) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2017.04.008 · Cited by 213
Hierarchical NiS/N-doped carbon composite hollow spheres with excellent supercapacitor performance
Liu, T., Jiang, C., Cheng, B., You, W., & Yu, J. (2017) · Journal of Materials Chemistry A · doi:10.1039/c7ta06149h · Cited by 211
Keshavarz, L., Ghaani, M. R., MacElroy, J. M. D., & English, N. J. (2021) · Chemical Engineering Journal · doi:10.1016/j.cej.2021.128604 · Cited by 210
Gund, G. S., Dubal, D. P., Jambure, S. B., Shinde, S. S., & Lokhande, C. D. (2013) · Journal of Materials Chemistry A · doi:10.1039/c3ta00024a · Cited by 210
Carbon aerogels derived from cresol–resorcinol–formaldehyde for supercapacitors
Li, W., Reichenauer, G., & Fricke, J. (2002) · Carbon · doi:10.1016/s0008-6223(02)00243-9 · Cited by 210
SnO2–graphene–carbon nanotube mixture for anode material with improved rate capacities
Zhang, B., Zheng, Q., Huang, Z., Oh, S. W., & Kim, J. (2011) · Carbon · doi:10.1016/j.carbon.2011.06.059 · Cited by 212
Synthesis and photocatalytic activity of BiOBr nanosheets with tunable exposed {0 1 0} facets
Xiong, X., Ding, L., Wang, Q., Li, Y., Jiang, Q., & Hu, J. (2016) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2016.02.018 · Cited by 210
Ning, X., Li, J., Yang, B., Zhen, W., Li, Z., Tian, B., & Lü, G. (2017) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2017.04.074 · Cited by 210
Zheng, Y., Zhu, B., Chen, H., You, W., Jiang, C., & Yu, J. (2017) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2017.06.014 · Cited by 210
Naik, B., Hazra, S., Prasad, V. S., & Ghosh, N. N. (2011) · Catalysis Communications · doi:10.1016/j.catcom.2011.03.028 · Cited by 209
Zhao, Y., Liu, S., Elsworth, D., Jiang, Y., & Zhu, J. (2014) · Energy & Fuels · doi:10.1021/ef500487d · Cited by 209
Bedia, J., Peñas‐Garzón, M., Gómez‐Avilés, A., Rodriguez, J. J., & Belver, C. (2018) · C – Journal of Carbon Research · doi:10.3390/c4040063 · Cited by 220
Luisetto, I., Tuti, S., Romano, C., Boaro, M., Bartolomeo, E. D., Kesavan, J. K., Kumar, S. S., & Selvakumar, K. (2019) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2019.01.006 · Cited by 211
Jawad, A. H., Abdulhameed, A. S., Reghioua, A., & Yaseen, Z. M. (2020) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2020.07.014 · Cited by 209
Malek, N. N. A., Jawad, A. H., Ismail, K., Razuan, R., & ALOthman, Z. A. (2021) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2021.08.160 · Cited by 209
Synthesis and Characterization of Nanosized ZnS Confined in Ordered Mesoporous Silica
Zhang, W., Shi, J., Chen, H., Hua, Z., & Yan, D. (2001) · Chemistry of Materials · doi:10.1021/cm000621r · Cited by 209
Yang, D., Kang, X., Ma, P., Dai, Y., Hou, Z., Cheng, Z., Li, C., & Lin, J. (2012) · Biomaterials · doi:10.1016/j.biomaterials.2012.11.004 · Cited by 208
Adsorption kinetics of malachite green onto activated carbon prepared from Tunçbilek lignite
Önal, Y., Başar, C. A., Sarıcı, D. E., Sarıcı-Özdemir, Ç., & Depçi, T. (2005) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2005.07.055 · Cited by 208
Bhunia, A., Boldog, I., Möller, A., & Janiak, C. (2013) · Journal of Materials Chemistry A · doi:10.1039/c3ta13407e · Cited by 208
El-Reesh, G. Y. A., Farghali, A. A., Taha, M., & Mahmoud, R. (2020) · Scientific Reports · doi:10.1038/s41598-020-57519-4 · Cited by 208
Sun, L., Tuo, J., Zhang, M., Wu, C., Wang, Z., & Zheng, Y. (2015) · Fuel · doi:10.1016/j.fuel.2015.05.061 · Cited by 209
Wu, F., Tseng, R., & Hu, C. (2005) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2004.12.005 · Cited by 208
Njoku, V. O., & Hameed, B. H. (2011) · Chemical Engineering Journal · doi:10.1016/j.cej.2011.07.075 · Cited by 207
Yu, X., Yu, J., Cheng, B., & Jaroniec, M. (2009) · The Journal of Physical Chemistry C · doi:10.1021/jp906992r · Cited by 207
Calik, M., Sick, T., Doḡru, M., Döblinger, M., Datz, S., Budde, H., Hartschuh, A., Auras, F., & Bein, T. (2015) · Journal of the American Chemical Society · doi:10.1021/jacs.5b10708 · Cited by 207
Seo, J., Bonneau, C., Matsuda, R., Takata, M., & Kitagawa, S. (2011) · Journal of the American Chemical Society · doi:10.1021/ja201484s · Cited by 207
Huang, Z., Li, F., Chen, B., Lü, T., Yuan, Y., & Yuan, G. (2013) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2013.01.057 · Cited by 208
Kruk, M., Dufour, B., Celer, E. B., Kowalewski, T., Jaroniec, M., & Matyjaszewski, K. A. (2005) · The Journal of Physical Chemistry B · doi:10.1021/jp045594x · Cited by 206
Xie, T., Xu, L., Liu, C., & Wang, Y. (2013) · Applied Surface Science · doi:10.1016/j.apsusc.2013.02.113 · Cited by 206
Weng, B., Zhang, X., Zhang, N., Tang, Z., & Xu, Y. (2015) · Langmuir · doi:10.1021/la504549y · Cited by 206
Mei, D., Zhang, B., Liu, R., Zhang, Y., & Liu, J. (2011) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2011.05.024 · Cited by 206
Li, C. C., Yin, X. M., Wang, T. H., & Zeng, H. C. (2009) · Chemistry of Materials · doi:10.1021/cm902126w · Cited by 205
Salam, M. A., Makki, M. S. I., & Abdelaal, M. Y. (2010) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2010.11.094 · Cited by 205
Kennedy, L. J., Vijaya, J. J., & SEKARAN, G. (2004) · Industrial & Engineering Chemistry Research · doi:10.1021/ie034093f · Cited by 205
Chen, J., Wang, Y., Liu, J., & Xu, X. (2020) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2020.02.055 · Cited by 205
Monsef, R., Ghiyasiyan-Arani, M., & Salavati‐Niasari, M. (2021) · ACS Applied Energy Materials · doi:10.1021/acsaem.0c02557 · Cited by 205
Zhang, J., Yan, Y., Wang, X., Cui, Y., Zhang, Z., Wang, S., Xie, Z., Yan, P., & Chen, W. (2023) · Nature Communications · doi:10.1038/s41467-023-39384-7 · Cited by 205
Element–organic frameworks with high permanent porosity
Rose, M., Böhlmann, W., Sabo, M., & Kaskel, S. (2008) · Chemical Communications · doi:10.1039/b718925g · Cited by 204
Physico-chemical characterization of Ni/MCM-41 synthesized by a template ion exchange approach
Lehmann, T., Wolff, T., Hamel, C., Veit, P., Garke, B., & Seidel‐Morgenstern, A. (2011) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2011.11.006 · Cited by 204
Srivastava, D. N., Perkas, N., Gedanken, A., & Felner, I. (2002) · The Journal of Physical Chemistry B · doi:10.1021/jp015532w · Cited by 204
Cheng, X., Huang, X., Wang, X., & Sun, D. (2009) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2009.12.063 · Cited by 204
Liu, G., Tian, P., Li, J., Zhang, D., Zhou, F., & Liu, Z. (2007) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2007.07.023 · Cited by 204
Phosphoryl functionalized mesoporous silica for uranium adsorption
Xue, G., Feng, Y., Ma, L., Dezhi, G., Jing, J., Yu, J., Haibin, S., Hongyu, G., & Yujun, Z. (2017) · Applied Surface Science · doi:10.1016/j.apsusc.2017.01.050 · Cited by 204
ZnO–CuO Core-Hollow Cube Nanostructures for Highly Sensitive Acetone Gas Sensors at the ppb Level
Lee, J. E., Lim, C. K., Park, H. J., Song, H., Choi, S., & Lee, D.-S. (2020) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.0c08593 · Cited by 204
Dehghani, A., Aslani, F., & Panah, N. G. (2021) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2021.123527 · Cited by 204
Shieh, F., Wang, S., Leo, S., & Wu, K. C. ‐. (2013) · Chemistry - A European Journal · doi:10.1002/chem.201301560 · Cited by 203
Weng, B., Wu, J., Zhang, N., & Xu, Y. (2014) · Langmuir · doi:10.1021/la4048566 · Cited by 203
Evaluation of the porous structure of Huadian oil shale during pyrolysis using multiple approaches
Bai, F., Sun, Y., Liu, Y., & Guo, M. (2016) · Fuel · doi:10.1016/j.fuel.2016.09.012 · Cited by 203
Li, Z., Liu, D., Cai, Y., Wang, Y., & Teng, J. (2019) · Fuel · doi:10.1016/j.fuel.2019.116031 · Cited by 203
Chowdhury, R., Khan, A., & Rashid, M. H. (2020) · RSC Advances · doi:10.1039/d0ra01479f · Cited by 203
Xiao, J., & Yang, S. (2012) · Journal of Materials Chemistry · doi:10.1039/c2jm31057k · Cited by 202
Porous silica microshells from diatoms as biocarrier for drug delivery applications
Aw, M. S., Simović, S., Yang, Y. L., Addai‐Mensah, J., & Lošić, D. (2011) · Powder Technology · doi:10.1016/j.powtec.2011.04.023 · Cited by 202
Singh, S., Barick, K. C., & Bahadur, D. (2013) · Journal of Materials Chemistry A · doi:10.1039/c2ta01045c · Cited by 202
Lin, J., Ding, B., Yang, J., Yu, J., & Sun, G. Z. (2011) · Nanoscale · doi:10.1039/c1nr10895f · Cited by 202
Niazi, L., Lashanizadegan, A., & Sharififard, H. (2018) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.03.026 · Cited by 202
Serafin, J., Baca, M., Biegun, M., Mijowska, E., Kaleńczuk, R. J., Sreńscek-Nazzal, J., & Michalkiewicz, B. (2019) · Applied Surface Science · doi:10.1016/j.apsusc.2019.143722 · Cited by 203
Park, S., & Jang, Y.-S. (2002) · Journal of Colloid and Interface Science · doi:10.1006/jcis.2002.8269 · Cited by 202
Aworn, A., Thiravetyan, P., & Nakbanpote, W. (2008) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2008.04.007 · Cited by 201
Fang, B., Xing, Y., Bonakdarpour, A., Zhang, S., & Wilkinson, D. P. (2015) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.5b00724 · Cited by 202
Rogers, J. L., Mangarella, M. C., D’Amico, A. D., Gallagher, J. R., Dutzer, M. R., Stavitski, E., Miller, J. T., & Sievers, C. (2016) · ACS Catalysis · doi:10.1021/acscatal.6b01133 · Cited by 201
Deng, C., Huang, Q., Zhu, X., Hu, Q., Su, W., Qian, J., Dong, L., Li, B., Fan, M., & Liang, C. (2016) · Applied Surface Science · doi:10.1016/j.apsusc.2016.08.035 · Cited by 201
Porous carbons derived from hypercrosslinked porous polymers for gas adsorption and energy storage
Zhang, C., Kong, R., Wang, X., Xu, Y., Wang, F., Ren, W., Wang, Y., Su, F., & Jiang, J. (2016) · Carbon · doi:10.1016/j.carbon.2016.12.064 · Cited by 201
Layered microporous polymers by solvent knitting method
Wang, S., Zhang, C., Yu, S., Jiang, S., Xia, Q. X., Chen, L., Jin, S., Hussaın, I., Cooper, A. I., & Tan, B. (2017) · Science Advances · doi:10.1126/sciadv.1602610 · Cited by 201
Hu, B. C., Yin, Y., Liu, G., Chen, S., Hong, X., & Tsang, S. C. E. (2018) · Journal of Catalysis · doi:10.1016/j.jcat.2017.12.029 · Cited by 201
Factors controling the SO2 removal by porous carbons: relevance of the SO2 oxidation step
Raymundo‐Piñero, E., Cazorla‐Amorós, D., de Lecea, C. S.-M., & Linares-Solano, A. (2000) · Carbon · doi:10.1016/s0008-6223(99)00109-8 · Cited by 200
Gonçalves, A. G., Figueiredo, J. L., Órfão, J. J. M., & Pereira, M. F. R. (2010) · Carbon · doi:10.1016/j.carbon.2010.07.051 · Cited by 200
Wu, N., Wei, H., & Zhang, L. (2011) · Environmental Science & Technology · doi:10.1021/es202043u · Cited by 201
An Interpenetrated Framework Material with Hysteretic CO2 Uptake
Mulfort, K. L., Farha, O. K., Malliakas, C. D., Kanatzidis, M. G., & Hupp, J. T. (2009) · Chemistry - A European Journal · doi:10.1002/chem.200902104 · Cited by 200
Kumar, P. S., Subramaniam, R., & Kannaiyan, S. (2010) · Korean Journal of Chemical Engineering · doi:10.1007/s11814-010-0342-0 · Cited by 200
Zhang, M., Song, L., Jiang, H., Shu, L., Shao, Y., Yang, J., & Li, J. (2017) · Journal of Materials Chemistry A · doi:10.1039/c6ta10513k · Cited by 200
Metadata
- Authors
- Sing, K. S. W.
- Corresponding author
- Sing, K. S. W.
- Venue
- Pure and Applied Chemistry
- Publisher
- Walter de Gruyter GmbH
- Published
- 1985-01-01
- Volume
- 57
- Issue
- 4
- Pages
- 603-619
- ISSN
- 0033-4545 (ISSN-L)
- 1365-3075
- OpenAlex
- W1980704616
- Cited by
- 24,485
- References
- 0
- Citations by year
- 2026: 917 · 2025: 1216 · 2024: 1289 · 2023: 1250 · 2022: 1384 · 2021: 1353 · 2020: 1435 · 2019: 1478 · 2018: 1441 · 2017: 1442 · 2016: 1401 · 2015: 1319 · 2014: 1238 · 2013: 1116 · 2012: 959
- FWCI
- 16.93
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Locations
- Pure and Applied Chemistry (publishedVersion)
- Topics
- Physical Sciences › Chemistry › Physical and Theoretical Chemistry › Adsorption, diffusion, and thermodynamic properties of materials
- Physical Sciences › Materials Science › Materials Chemistry › Mesoporous Materials and Catalysis
- Physical Sciences › Chemistry › Analytical Chemistry › Analytical Chemistry and Chromatography
- Keywords
- physisorption, gas-solid systems, surface area determination, porosity determination, reporting recommendations, adsorption isotherms, BET method
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
