Cited by 282Clay minerals and soil interactionsGeochemistry and Elemental AnalysisSoil and Environmental Studies

Surface area and porosity of primary silicate minerals

Brantley, Susan L., Mellott, Nathan P.·2000·American Mineralogist

Abstract

Surface area is important in quantifying mineral-water reaction rates. Specific surface area (SSA) was measured to investigate controls on this parameter for several primary silicate minerals (PSM) used to estimate rates of weathering. The SSA measured by gas adsorption for a given particle size of relatively impurity-free, laboratory-ground samples generally increases in the order: quartz ≈ olivine ≈ albite < oligoclase ≈ bytownite < hornblende ≈ diopside. Reproducibility of BET SSA values range from ±70% (SSA < 1000 cm 2 /g) to ± 5% (SSA > 4000 cm 2 /g) and values measured with N 2 were observed to be up to 50% larger than values measured with Kr. For laboratory-ground Amelia albite and San Carlos olivine, SSA can be calculated using log (SSA, cm 2 /g) = b + m log (d), where d = grain diameter (μm), b = 5.2 ± 0.2 and m = -1.0 ± 0.1. A similar equation was previously published for laboratory-ground quartz. Some other samples showed SSA higher than predicted by these equations. In some cases, high SSA is attributed to significant second phase particulate content, but for other laboratory-ground samples, high SSA increased with observed hysteresis in the adsorption-desorption isotherms. Such hysteresis is consistent with the presence of pores with diameters in the range 2 to 50 nm (mesopores). In particular, porosity that contributes to BET-measured SSA is inferred for examples of laboratory-ground diopside, hornblende, and all compositions of plagioclase except albite, plus naturally weathered quartz, plagioclase, and potassium feldspar. Previous workers documented similar porosity in laboratory-ground potassium feldspar. Surface area measured by gas adsorption may not be appropriate for extrapolation of interfacelimited rates of dissolution of many silicates if internal surface is present and if it does not dissolve equivalently to external surface. In addition, the large errors associated in measuring SSA of coarse and/or impurity-containing silicates suggest that surface area-normalized kinetics in both field and laboratory systems will be difficult to estimate precisely. Quantification of the porosity in laboratory- ground and naturally weathered samples may help to alleviate some of the discrepancy between laboratory- and field-based estimates of weathering rate

Integrity signals

Registry

Crossref · 10.2138/am-2000-11-1220

Cites

53 of 53 references verified0 citation errors · 0 not checkable

Statistics

Recomputing p-values needs the paper’s full text.

Claims the paper makes

This paper’s full text isn’t openly available, so its claims and self-check weren’t run. The registry and citation checks still apply.

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Cites

Flagged first, then by citations

Cited by

Sorted by citations

Authors
Brantley, S. L., & Mellott, N. P.
Affiliations
Pennsylvania State University (US)
Corresponding author
Mellott, Nathan P.
Venue
American Mineralogist
Published
2000-11
Volume
85
Issue
11-12
Pages
1767-1783
ISSN
0003-004X (ISSN-L)
OpenAlex
W2394638777
Cited by
282
References
53
Citations by year
2026: 14 · 2025: 21 · 2024: 10 · 2023: 10 · 2022: 13 · 2021: 12 · 2020: 13 · 2019: 6 · 2018: 11 · 2017: 6 · 2016: 11 · 2015: 15 · 2014: 14 · 2013: 17 · 2012: 22
FWCI
2.12
Type
journal article
Language
en
Open access
closed
Locations
American Mineralogist (publishedVersion)
Topics
  • Physical Sciences › Materials Science › Biomaterials › Clay minerals and soil interactions
  • Physical Sciences › Earth and Planetary Sciences › Geochemistry and Petrology › Geochemistry and Elemental Analysis
  • Life Sciences › Agricultural and Biological Sciences › Soil Science › Soil and Environmental Studies
Keywords
specific surface area, porosity, mineral weathering, adsorption hysteresis, mesopores, quartz, olivine, albite, plagioclase, hornblende, diopside, feldspar, dissolution kinetics, grain size effects

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review