CoChat

Sub- and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin

Open access

The DOI matches its Crossref record; 151 of the 151 references it cites were found in a registry or an index; 56 of the 234 sources its claims cite were checked for support.

Abstract

To mitigate global warming, humankind has been forced to develop new efficient energy solutions based on renewable energy sources. Hydrothermal liquefaction (HTL) is a promising technology that can efficiently produce bio-oil from several biomass sources. The HTL process uses sub- or supercritical water for producing bio-oil, water-soluble organics, gaseous products and char. Black liquor mainly contains cooking chemicals (mainly alkali salts) lignin and the hemicellulose parts of the wood chips used for cellulose digestion. This review explores the effects of different process parameters, solvents and catalysts for the HTL of black liquor or black liquor-derived lignin. Using short residence times under near- or supercritical water conditions may improve both the quality and the quantity of the bio-oil yield. The quality and yield of bio-oil can be further improved by using solvents (e.g., phenol) and catalysts (e.g., alkali salts, zirconia). However, the solubility of alkali salts present in black liquor can lead to clogging problem in the HTL reactor and process tubes when approaching supercritical water conditions.

Overview

CoChat Summary

TL;DR

This review synthesizes hydrothermal liquefaction (HTL) of black liquor and black liquor-derived lignin, focusing on process parameters, salts, catalysts, co-solvents, reaction chemistry, bio-oil quality, and techno-economics. It concludes that HTL is promising but faces key challenges from salt precipitation/fouling, limited continuous supercritical-water data, and bio-oil costs above fossil crude.

Key findings

  • Reported bio-oil yields vary widely: up to 80 wt.% carbon yield from black liquor to bio-oil; Table 6 lists maxima of 87.7 wt.% for LignoBoost lignin in a continuous catalytic fixed-bed reactor, 78 wt.% for black liquor in batch, and 90 wt.% for alkali lignin in batch with ethanol.
  • Temperature and residence time strongly affect yields: Orebom et al. found bio-oil yield rose from ca. 67 wt.% to a maximum of 78 wt.% at ca. 648 K, then fell to ca. 60 wt.% at 693 K; at 653 K, maximum bio-oil yield was 76 wt.% at 20 min, decreasing to ca. 68 wt.% at 120 min. Lee et al. reported highest bio-oil yield ca. 62 wt.% at 623 K and 5 min, with yields dropping to ca. 30 wt.% at 30 min above ca. 620 K.
  • Black liquor salts can foul reactors: at HTL water densities of roughly 400–750 kg/m³, sodium sulfate solubility can fall from ca. 200 g/kg to 2 g/kg and sodium carbonate to 5 g/kg; a Paul Scherrer Institute salt separator recovered >95% of a K₂SO₄/Na₂CO₃ mixture as concentrated brine.
  • Additives and economics: phenol as co-solvent raised bio-oil yield from 34 to 102 wt.% as initial phenol increased from 0 to 10 wt.%; K₂CO₃ increased phenolic yield from 16.9 to 27.1 wt.% but suspended solids from 0.1 to 22.9 wt.%; ZrO₂ gave 15.9 wt.% light oil versus 8.4 wt.% with glass beads. Techno-economic assessments reported minimum selling prices of 0.93–1.05 $/liter, while Brent crude averaged 0.36–0.83 $/liter over five years.

Methods

  • Design: narrative literature review of HTL applied to black liquor and black liquor-derived lignin, covering process parameters, salt behavior, catalysts, co-solvents, reaction pathways, bio-oil quality, and techno-economic analyses.
  • Data: published experimental studies and TEAs using feedstocks including black liquor, Kraft lignin, LignoBoost lignin, alkali lignin, and Indulin AT, with batch, continuous, catalytic fixed-bed, and CSTR systems.
  • Analysis: thematic synthesis and comparison of reported yields, product compositions, process conditions, and economic estimates; no new experiments are reported.

Limitations

  • Stated: comparing studies is difficult because of different feedstocks, experimental methodologies, and ways of expressing mass yields; there is no data from continuous supercritical-water reactors on black liquor; no complete reaction mechanism or kinetic model exists for black liquor lignin degradation, and the suitability of the Indulin AT model for black liquor is unclear.
  • Stated: salt mixture phase behavior in supercritical water is hard to predict, and no specific study has been published on black liquor salt mixtures; research on corrosion-resistant materials for black liquor HTL is lacking.
  • Evident: as a review, it provides no primary experimental validation and depends on heterogeneous cited studies; several reported comparisons are limited by inconsistent data presentation across sources.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.3390/en13133309

Cites

151 of 151 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Figure 1 The main material flows in a Kraft pulp mill process. ( DM = Dry Matter). The figure is redrawn from Biermann [33]. Figure 1. The main material flows in a Kraft pulp mill process. ( DM = Dry Matter). The figure is redrawn from Biermann [33].
Figure 1 The main material flows in a Kraft pulp mill process. ( DM = Dry Matter). The figure is redrawn from Biermann [33]. Figure 1. The main material flows in a Kraft pulp mill process. ( DM = Dry Matter). The figure is redrawn from Biermann [33].From the PDF
Figure 2 Density and enthalpy of water as a function of temperature at various pressures. The data points are taken from Wagner and Pruß [60]: ( a ) density; ( b ) enthalpy. Figure 2. Density and enthalpy of water as a function of temperature at various pressures. The data points are taken from Wagner and Pruß [60]: ( a ) density; ( b ) enthalpy.
Figure 2 Density and enthalpy of water as a function of temperature at various pressures. The data points are taken from Wagner and Pruß [60]: ( a ) density; ( b ) enthalpy. Figure 2. Density and enthalpy of water as a function of temperature at various pressures. The data points are taken from Wagner and Pruß [60]: ( a ) density; ( b ) enthalpy.From the PDF
Image 3
From the PDF
( a ) ( b ) Figure 4. Logarithmic ionic product ( pKw ) and dielectric constant ( ε 0 ) of water as a function of temperature at various pressures. The data points are taken from IAPWS [63,64]: ( a ) Ionic product Figure 4. Logarithmic ionic product ( pKw ) and dielectric constant ( ε 0 ) of water as a function of temperature at various pressures. The data points are taken from IAPWS [63,64]: ( a ) Ionic product (pKw); ( b ) Dielectric Constant. Figure 4. Logarithmic ionic product ( pKw ) and dielectric constant ( " 0 ) of water as a function of temperature at various pressures. The data points are taken from IAPWS [63,64]: ( a ) Ionic product (pKw); ( b ) Dielectric Constant.
( a ) ( b ) Figure 4. Logarithmic ionic product ( pKw ) and dielectric constant ( ε 0 ) of water as a function of temperature at various pressures. The data points are taken from IAPWS [63,64]: ( a ) Ionic product Figure 4. Logarithmic ionic product ( pKw ) and dielectric constant ( ε 0 ) of water as a function of temperature at various pressures. The data points are taken from IAPWS [63,64]: ( a ) Ionic product (pKw); ( b ) Dielectric Constant. Figure 4. Logarithmic ionic product ( pKw ) and dielectric constant ( " 0 ) of water as a function of temperature at various pressures. The data points are taken from IAPWS [63,64]: ( a ) Ionic product (pKw); ( b ) Dielectric Constant.From the PDF
Figure 5 Schematic representation of the behavior of Type 1 and 2 salts at high pressure and Figure 5. Schematic representation of the behavior of Type 1 and 2 salts at high pressure and temperature.
Figure 5 Schematic representation of the behavior of Type 1 and 2 salts at high pressure and Figure 5. Schematic representation of the behavior of Type 1 and 2 salts at high pressure and temperature.From the PDF
Image 6
From the PDF
Figure 7 Mass yield of bio-oil as a function of operating temperature. The curves are guides to the Figure 7. Mass yield of bio-oil as a function of operating temperature. The curves are guides to the eye.
Figure 7 Mass yield of bio-oil as a function of operating temperature. The curves are guides to the Figure 7. Mass yield of bio-oil as a function of operating temperature. The curves are guides to the eye.From the PDF
Figure 8 Effect of temperature on mass fractions of monocyclic aromatic compounds in bio-oil. Data is taken from [107]. The curves are guides to the eye. Figure 8. E ect of temperature on mass fractions of monocyclic aromatic compounds in bio-oil. Data is taken from [107]. The curves are guides to the eye. Energies 2020 , 13 , x FOR PEER REVIEW 17 of 46
Figure 8 Effect of temperature on mass fractions of monocyclic aromatic compounds in bio-oil. Data is taken from [107]. The curves are guides to the eye. Figure 8. E ect of temperature on mass fractions of monocyclic aromatic compounds in bio-oil. Data is taken from [107]. The curves are guides to the eye. Energies 2020 , 13 , x FOR PEER REVIEW 17 of 46From the PDF
Image 9
From the PDF
Figure 10 Bio-oil yield as a function of residence time. All the experiments were performed in batch Figure 10. Bio-oil yield as a function of residence time. All the experiments were performed in batch reactors. The curves are guides to the eye.
Figure 10 Bio-oil yield as a function of residence time. All the experiments were performed in batch Figure 10. Bio-oil yield as a function of residence time. All the experiments were performed in batch reactors. The curves are guides to the eye.From the PDF
Figure 11 The influence of residence time on char yield. All the experiments were performed in batch Figure 11. The influence of residence time on char yield. All the experiments were performed in batch reactors. The curves are guides to the eye.
Figure 11 The influence of residence time on char yield. All the experiments were performed in batch Figure 11. The influence of residence time on char yield. All the experiments were performed in batch reactors. The curves are guides to the eye.From the PDF
Figure 12 Effect of the initial KOH concentration on the total yields (both WSO and bio-oil) of various components. The feedstock for the HTL process was Kraft lignin. The curves are guides to the eye. Data is taken from Belkheiri et al. [115]. Figure 12. E ect of the initial KOH concentration on the total yields (both WSO and bio-oil) of various components. The feedstock for the HTL process was Kraft lignin. The curves are guides to the eye. Data is taken from Belkheiri et al. [115].
Figure 12 Effect of the initial KOH concentration on the total yields (both WSO and bio-oil) of various components. The feedstock for the HTL process was Kraft lignin. The curves are guides to the eye. Data is taken from Belkheiri et al. [115]. Figure 12. E ect of the initial KOH concentration on the total yields (both WSO and bio-oil) of various components. The feedstock for the HTL process was Kraft lignin. The curves are guides to the eye. Data is taken from Belkheiri et al. [115].From the PDF
Figure 13 Reaction pathway for the degradation of Indulin AT. Figure is adapted from Schuler [140].
Figure 13 Reaction pathway for the degradation of Indulin AT. Figure is adapted from Schuler [140].From the PDF

Verification

Claims the paper makes

52 Valid · 15 Not valid · 141 Not checked · 98 Own results and interpretations

129 more claims · 18 with their cited sources checked

Create a free account to see all 306 claims and every source verdict.

See all claims — free account
  • Probably not a substantial claim. 85
  • It may state two separate claims as one. 115
  • The quote only partly states this claim. 4
  • Not yet classified. 1

Create a free account to see these claims.

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

Each contradiction between two passages listed here was confirmed by an independent check.

5 of 7 · the rest aren’t loaded

2 more findings

Create a free account to see every finding of this check.

See all findings — free account

Citations

Cites

Show all 151 references

Research works printed but not linked: 12

  1. Sims, R.E.H. (2003). Bioenergy Options for a Cleaner Environment in Developed and Developing Countries, Elsevier Science & Technology.
  2. International Energy Agency Black Liquor Gasification (2007). Summary and Conclusions from the IEA Bioenergy ExCo54 Workshop, International Energy Agency.
  3. Sjöström, E. (1981). Wood Chemistry: Fundamentals and Applications, Academic Press.
  4. Stokke, D.D., Wu, Q., Han, G., and Stevens, C.V. Introduction to Wood and Natural Fiber Composites, John Wiley & Sons, Incorporate. [1st ed.].
  5. Sjöström, E. (1993). Wood Chemistry: Fundamentals and Applications, Academic Press, Inc.. [2nd ed.].
  6. Sjöström, E. (1965). Preface to the first edition. Wood Chemistry: Fundamentals and Applications, Academic Press, Inc.
  7. Rumyantsev, 1977, Selection of mineralizers in the hydrothermal synthesis and growth of crystals, Sov. Phys. Crystallogr., 22, 610
  8. Tomani, 2010, The lignoboost process, Cellul. Chem. Technol., 44, 53
  9. Välimäki, A. (2017). Mustalipeän hydrotermisen nesteytyksen vaikutus bioöljyn laatuun (Improving bio-oil quality in hydrothermal liquefaction of black liquor). [Master’s Thesis, Aalto University].
  10. Tran, 1990, Chloride and Potassium in the Kraft Recovery Cycle: A Practical Guide, Pulp Pap. Can. Ont., 91, 185
  11. Hupa, 2007, Recovery boiler chemical principles, TAPPI Kraft Recover. Course, 2007, 2
  12. Schuler, J. (2019). Hydrothermal Liquefaction of Lignin. [Ph.D. Thesis, Karlsruhe Institute of Technology].

Cited by

See all 87

Metadata

Authors
Lappalainen, J., Baudouin, D., Hornung, U., Schuler, J., Melin, K., Bjelić, S., Vogel, F., Konttinen, J., & Joronen, T.
Affiliations
  • Tampere University (FI)
  • Paul Scherrer Institute (CH)
  • Karlsruhe Institute of Technology (DE)
  • VTT Technical Research Centre of Finland (FI)
Corresponding author
Lappalainen, Jukka
Venue
Energies
Publisher
MDPI AG
Published
2020-06-28
Volume
13
Issue
13
Pages
3309
ISSN
1996-1073 (ISSN-L)
OpenAlex
W3037144356
Cited by
87
References
150
Citations by year
2026: 13 · 2025: 12 · 2024: 20 · 2023: 17 · 2022: 10 · 2021: 12 · 2020: 3
FWCI
3.30
Type
journal article
Language
en
Open access
Locations
  • Energies (publishedVersion, cc-by)
  • Repository KITopen (Karlsruhe Institute of Technology) (submittedVersion, cc-by)
  • DORA PSI (Paul Scherrer Institute) (submittedVersion, cc-by)
  • RePEc: Research Papers in Economics (submittedVersion)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
  • Tampere University Institutional Repository (Tampere University) (submittedVersion, cc-by)
  • KITopen (cc-by)
Funders
European Commission (884111)
Topics
  • Physical Sciences › Chemical Engineering › Process Chemistry and Technology › Subcritical and Supercritical Water Processes
  • Physical Sciences › Energy › Fuel Technology › Thermochemical Biomass Conversion Processes
  • Physical Sciences › Chemical Engineering › Process Chemistry and Technology › Lignin and Wood Chemistry
Keywords
hydrothermal liquefaction, black liquor, kraft lignin, lignin valorization, supercritical water, subcritical water, bio-oil, alkali metal salts, zirconia catalysts, residence time, reactor clogging

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

The claim verdicts this report counts are experimental: their accuracy is not yet measured.

A language model drew the claims from the paper on 2026-09-28, under version 3 of the claim definition (prompt extract-v3).

A second model labelled each claim on 2026-09-28 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Cited sources are checked with a language model’s help (gpt-6-sol).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Sub- and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin. https://app.cochat.ai/papers/10.3390/en13133309
The paper
Lappalainen, J., Baudouin, D., Hornung, U., Schuler, J., Melin, K., Bjelić, S., Vogel, F., Konttinen, J., & Joronen, T. (2020). Sub- and Supercritical Water Liquefaction of Kraft Lignin and Black Liquor Derived Lignin. Energies. https://doi.org/10.3390/en13133309

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.