Modeling and Simulation of Photobioreactors with Computational Fluid Dynamics—A Comprehensive Review
Open accessThe DOI matches its Crossref record; 350 of the 350 references it cites were found in a registry or an index; 75 of the 542 sources its claims cite were checked for support.
Abstract
Comprehensive review of CFD sub-models relevant to photobioreactor simulation, including flow, light, heat/mass transfer, and growth kinetics.
Overview
CoChat Summary
TL;DR
This review surveys CFD models of photobioreactors and the sub-models available for light transfer, single- and multiphase flow, turbulence, interphase forces, population balance, mass transfer, heat transfer, and growth kinetics. It concludes that no "complete" model considering all relevant phenomena has yet been proposed, that published CFD models often lag behind state-of-the-art fluid-dynamics modeling, and that systematic experimental validation for specific reactor geometries is lacking.
Key findings
- No "complete" model that considers all phenomena occurring in photobioreactors has been suggested so far; the authors state this follows from their Table 1 overview of selected CFD models.
- Interphase mass transfer is "rarely considered" in CFD simulations of photobioreactors and, when included, is simplified — e.g., in Bari et al. [17] the gas transfer rate is evaluated from the superficial gas velocity (a boundary condition), and in Mink [21] no gas bubbles are simulated so interphase mass transfer does not take place.
- Temperature dependency of growth is argued to be unreasonable to include in CFD models: acclimation occurs on much longer time scales than mixing, so on seconds-to-minutes scales growth can be expressed as μ(T_ave) rather than μ_ave(T).
- Microalgae cells behave as passive tracers: with cell diameters of order micrometers, τ_v is estimated at 10⁻⁷–10⁻⁸ s versus flow time scales τ_f of 10⁻¹–10⁰ s, giving St ≪ 1, so inertia, lift forces and rotation are negligible.
- Predictive power is limited by parameter uncertainty: for light propagation, accuracy of predicted light distribution and absorption is affected similarly by the choice of light propagation model and by uncertainty in the cells' optical characteristics [13]; appropriate growth-kinetic parameters are unknown for many species.
Methods
- Design: narrative/comprehensive literature review (Review article, Energies 2022, 15, 3966), organized into photobioreactor types and phenomena (Section 2), an overview of published CFD models (Section 3), and an overview of state-of-the-art sub-models (Section 4), followed by discussion and conclusions.
- Data: no primary experiments; the paper compiles and compares published CFD studies of photobioreactors (Tables 1 and 2) and published sub-models/correlations (e.g., Tables 3–15 covering photosynthesis–irradiance models, turbulence models, interphase force correlations, break-up/coalescence models, mass transfer and heat transfer correlations).
- Analysis: qualitative comparison of model choices against state-of-the-art approaches from the fluid dynamics community, with discussion of strengths, deficiencies and applicability to specific reactor types.
Limitations
- Stated: the listing of CFD models is not claimed to be complete — it is intended as a representative overview; the review also restricts itself to common submerged-culture reactor types and omits alternative designs (e.g., [53–55]) and non-CFD modeling approaches (e.g., [68,123,124]).
- Stated: although many available models have been compared with experimental results in lab-scale reactors, "there is in general a lack of systematic comparison for specific bioreactor types."
- Stated: model parameters are often unknown when they reflect cell properties, and because light propagation, biomass concentration and growth interact non-linearly, predictive power "must be expected to suffer greatly from parameter uncertainty."
- Evident from the text: several sections (e.g., 2.2.3 Interphase Mass Transfer, 2.2.4 Heat Transfer, 4.7 Heat Transfer) appear in truncated or fragmented form in the provided text, and many equations are not decoded, so the quantitative content of those sub-models cannot be verified here.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
55 Valid · 21 Not valid · 246 Not checked · 141 Own results and interpretations
At least one cited source doesn’t support this claim or points to a different paper, and none confirmed it — see the verdicts below.
In the paper
“According to Table 1, the majority of gas-liquid flows is modeled in the EulerianEulerian formulation [18,25-27,29-31,39-42,45,125,135,136], thus, as two interpenetrating continua.”
What the sources say
- Not checked — no full text of the sourcecites [18] McHardy, 2018, Numerical analysis of the effects of air on light distribution in a bubble column photobioreactor, Algal Res. source
- Not checked — no full text of the sourcecites [25] Nauha, 2013, Modeling method for combining fluid dynamics and algal growth in a bubble column photobioreactor, Chem. Eng. J. source
- Not checked — no full text of the sourcecites [26] Luzi, 2019, Comparison between different strategies for the realization of flashing-light effects – Pneumatic mixing and flashing illumination, Algal Res. source
- Disputedcites [27] Loomba, 2018, Single-cell computational analysis of light harvesting in a flat-panel photo-bioreactor, Biotechnol. Biofuels sourceExperimental — accuracy not yet measured
The Methods (Hydrodynamics) explicitly say this model uses an Eulerian approach for the liquid but a Lagrangian slip-model approach for gas velocity. It therefore does not exemplify the Eulerian–Eulerian formulation for which the citing sentence includes it; this paper alone also cannot establish what the majority of models use. (LLM, conf=0.88)
Checked by a reasoning model — may be wrong.
- Not checked — no full text of the sourcecites [29] Sato, 2010, Development of virtual photobioreactor for microalgae culture considering turbulent flow and flashing light effect, Energy Convers. Manag. source
- Not checked — no full text of the sourcecites [30] Gao, 2017, Comprehensive computational model for combining fluid hydrodynamics, light transport and biomass growth in a Taylor vortex algal photobioreactor: Eulerian approach, Algal Res. source
- Not checked — no full text of the sourcecites [31] Gao, 2017, Comprehensive computational model for combining fluid hydrodynamics, light transport and biomass growth in a Taylor vortex algal photobioreactor: Lagrangian approach, Bioresour. Technol. source
- Not checked — no full text of the sourcecites [39] Cho, 2019, The development of a thermosiphon photobioreactor and analysis using Computational Fluid Dynamics (CFD), Chem. Eng. J. source
- Not checked — no full text of the sourcecites [40] Wang, 2014, A novel flat plate algal bioreactor with horizontal baffles: Structural optimization and cultivation performance, Bioresour. Technol. source
- Not checked — no full text of the sourcecites [41] Ali, 2019, CFD and kinetic-based modeling to optimize the sparger design of a large-scale photobioreactor for scaling up of biofuel production, Biotechnol. Bioeng. source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“However, a major restriction for growing microalgae phototrophically is that the dry biomass concentration in photobioreactors is typically restricted to a few g/L.”
What the sources say
- Not checked — no full text of the sourcecites [4] Shilton, 2013, Modeling the effects of light and temperature on algae growth: State of the art and critical assessment for productivity prediction during outdoor cultivation, Biotechnol. Adv. source
- Not matchedcites [5] Bux, F., and Chisti, Y. (2016). Large-Scale Production of Algal Biomass: Photobioreactors. Algae Biotechnology: Products and Processes, Springer International Publishing.
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
- Partly supportedcites [6] Endres, C.H. (2017). Modeling Temperature and Microalgae Productivity for Photobioreactors in Industrial-Scale Cultivation Plants. [Ph.D. Dissertation, Technische Universität München].Experimental — accuracy not yet measured
Section 3.3.6.1 (Cell concentration; page not available) uses 2 g/L and explains that lowering it to 1 g/L can improve light penetration and reduce dark zones in some reactors. This supports a concentration-related constraint, but a concentration chosen for this study does not establish that photobioreactors are typically restricted to a few g/L. (LLM, conf=0.82)
- Could not verifycites [7] Laviale, 2017, Modeling the impact of high temperatures on microalgal viability and photosynthetic activity, Biotechnol. Biofuels sourceExperimental — accuracy not yet measured
The Background discusses uncertainty in full-scale algal productivity, and Methods > Algal species and cultivation conditions gives a cell count for one culture. Neither establishes a typical dry biomass concentration or a limit of a few g/L in photobioreactors. Searches for dry biomass concentration, g/L, and related terms found no supporting passage; page numbers were unavailable in our copy. (LLM, conf=0.77)
- Partly supportedcites [8] Schediwy, 2019, Microalgal kinetics—A guideline for photobioreactor design and process development, Eng. Life Sci. sourceExperimental — accuracy not yet measured
The ‘Impact of light kinetics on reactor design’ section (page unavailable) says that excessive biomass concentration for a given reactor thickness reduces productivity, and that high concentrations require thin reactors. It does not give a typical dry-biomass limit of a few g/L for photobioreactors. (LLM, conf=0.82)
- Partly supportedcites [9] Legrand, 2021, A review on photobioreactor design and modelling for microalgae production, React. Chem. Eng. sourceExperimental — accuracy not yet measured
The ‘Light energy in photobioreactors’ section explains that high biomass concentration creates dark zones that reduce productivity, supporting a light-related restriction on phototrophic growth. It does not establish that dry biomass concentration is typically limited to a few g/L; searches for that concentration and equivalent units found no such figure. (LLM, conf=0.83)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“However, assessing flow conditions can be complex as the flow in many photobioreactors is governed by multiple interactions between the flowing liquid and a dispersed gas phase [14-16].”
What the sources say
- Not checked — no full text of the sourcecites [14] Posten, 2009, Design principles of photo-bioreactors for cultivation of microalgae, Eng. Life Sci. source
- Not checked — no full text of the sourcecites [15] Olivieri, 2013, Advances in photobioreactors for intensive microalgal production: Configurations, operating strategies and applications, J. Chem. Technol. Biotechnol. source
- Supportedcites [16] Huang, 2017, Design of Photobioreactors for Mass Cultivation of Photosynthetic Organisms, Engineering source
Section 4, “Advances in the modeling of PBRs” (page not provided), describes bubbly flow in photobioreactors and says its simulation is complicated by turbulence and interphase momentum exchange. This supports the claim that liquid–gas interactions make flow conditions complex. (LLM, conf=0.88)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“It is also often neglected that reflection or refraction at the various interfaces cause additional heterogeneity of the light intensity distribution and even dark regions may arise in consequence [21,85].”
What the sources say
- Partly supportedcites [21] Mink, A. (2022). A Comprehensive Computational Model for Coupled Fluid Flow, Mass Transfer and Light Supply in Photobioreactors with Lattice Boltzmann Methods. [Ph.D. Thesis, Karlsruher Institut für Technologie]. sourceExperimental — accuracy not yet measured
The Light Distribution Model (p. 5) describes reflection and refraction at surfaces and the resulting attenuation of light. The Light Simulation of Complex Geometry (p. 9) reports a heterogeneous distribution with dark zones, but attributes those zones to a steep radial light gradient, not specifically to reflection or refraction at interfaces. (LLM, conf=0.82)
- Supportedcites [85] Marotta, 2017, Reflection-refraction effects on light distribution inside tubular photobioreactors, Can. J. Chem. Eng. source
The Results and Discussion section (page not provided) says that accounting for reflection and refraction at the photobioreactor wall strongly changes the light-absorption distribution and produces completely dark zones absent when those effects are neglected. It also describes a less uniform distribution at low algae concentrations. (LLM, conf=0.92)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“In complex geometries, an accurate estimation of the light distribution requires three-dimensional computations [21].”
What the sources say
- Partly supportedcites [21] Mink, A. (2022). A Comprehensive Computational Model for Coupled Fluid Flow, Mass Transfer and Light Supply in Photobioreactors with Lattice Boltzmann Methods. [Ph.D. Thesis, Karlsruher Institut für Technologie]. sourceExperimental — accuracy not yet measured
The Introduction (p. 2) describes a three-dimensional model for light supply in a tubular photobioreactor with sponges, and the Validation section (p. 8) reports agreement with measured light intensities. The paper supports the use of 3D computation for this complex geometry, but does not establish that accurate estimates in complex geometries require 3D computation rather than another approach. (LLM, conf=0.85)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
131 more claims · 21 with their cited sources checked
Create a free account to see all 463 claims and to verify the 9 references still open.
- Probably not a substantial claim. 247
- It may state two separate claims as one. 172
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“As existing models of complete PBR are highly differing in the assembly of the multiphysics simulation modules [4], a direct comparison of results is hardly possible.”
From Comprehensive Computational Model for Coupled Fluid Flow, Mass Transfer, and Light Supply in Tubular Photobioreactors Equipped with Glass Sponges (2022) · cites this paper as [4]
Experimental — accuracy not yet measuredThe check wasn’t confident either way, so it gives no verdict — never disputed.
In the citing paper
“IoT, in turn, connects smart sensors to real-time analytics platforms, allowing the dynamic adjustment of parameters such as temperature, pH, CO2 concentration, and light intensity, thereby converting the PBR into a responsive and intelligent system (Cui et al., 2020; Luzi and McHardy, 2022).”
From Microalgae biotechnology and its role in sustainable and healthy food design (2025) · cites this paper as Luzi and McHardy, 2022
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 3.1. Light Transfer
“Instead of using simplified or analytical models, some researchers selected the second approach, which is solving the full RTE numerically in one or more dimensions [18,21,26-28,34].”
§ 3.3. Multiphase Flow
“| Mink et al. [21] | DA | LBM | 3D”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 4.4.2. Euler-Lagrange Modeling of Microalgae Cells
“Accordingly, the motion of cells is governed by inertia and the action of lift forces and rotation is negligible.”
§ 4.4.2. Euler-Lagrange Modeling of Microalgae Cells
“Therefore, St ≪ 1, which means that cells follow the flow passively.”
Citations
Cites
Two-equation eddy-viscosity turbulence models for engineering applications
Menter, F. R. (1994) · AIAA Journal · doi:10.2514/3.12149 · Cited by 21,593
Chisti, Y. (2007) · Biotechnology Advances · doi:10.1016/j.biotechadv.2007.02.001 · Cited by 9,524 · cited 1×
“This requires a bio-economy being based on the utilization of sustainable resources, of which microalgae may be part of [1] as they can be cultivated in photobioreactors with high area yields and productivity [2,3].”
BackgroundA dynamic subgrid–scale eddy viscosity model
Germano, M., Piomelli, U., Moin, P., & Cabot, W. H. (1991) · Physics of Fluids A: Fluid Dynamics · doi:10.1063/1.857955 · Cited by 7,305
A new k-ε eddy viscosity model for high Reynolds number turbulent flows
Shih, T.-H., Liou, W. W., Shabbir, A., Yang, Z., & Zhu, J. (1995) · Computers & Fluids · doi:10.1016/0045-7930(94)00032-t · Cited by 6,119
Turbulence statistics in fully developed channel flow at low Reynolds number
Kim, J., Moin, P., & Moser, R. (1987) · Journal of Fluid Mechanics · doi:10.1017/s0022112087000892 · Cited by 4,873
Subgrid-scale stress modelling based on the square of the velocity gradient tensor
Nicoud, F., & Ducros, F. (1999) · Flow, Turbulence and Combustion · doi:10.1023/a:1009995426001 · Cited by 4,161
A proposed modification of the Germano subgrid–scale closure method
Lilly, D. K. (1992) · Physics of Fluids A: Fluid Dynamics · doi:10.1063/1.858280 · Cited by 4,077
Reassessment of the scale-determining equation for advanced turbulence models
Wilcox, D. C. (1988) · AIAA Journal · doi:10.2514/3.10041 · Cited by 3,117
Multiphase Flows with Droplets and Particles
Crowe, C. T., Schwarzkopf, J. D., Sommerfeld, M., & Tsuji, Y. (2011) · doi:10.1201/b11103 · Cited by 3,076
Development of turbulence models for shear flows by a double expansion technique
Yakhot, V., Orszag, S. A., Thangam, S., Gatski, T. B., & Speziale, C. G. (1992) · Physics of Fluids A: Fluid Dynamics · doi:10.1063/1.858424 · Cited by 2,832
Research works printed but not linked: 8
- Clift, R., R Grace, J., and E Weber, M. (1978). Bubbles, Drops, and Particles, Academic Press.
- Wray, A., and Hunt, J. (1990, January 13–18). Algorithms for classification of turbulent structures; Topological Fluid Mechanics. Proceedings of the IUTAM Symposium, Cambridge, UK.
- Schiller, 1933, Über die grundlegenden Berechnungen bei der Schwerkraftaufbereitung, Z. Des Vereines Dtsch. Ingenieure, 77, 318
- Rusche, H., and Issa, R. (2000, January 25–29). The Effect of Voidage on the Drag Force on Particles, Droplets and Bubbles in Dispersed Two-Phase Flow. Proceedings of the Japanese European Two-Phase Flow Group Meeting, Tsukuba, Japan.
- Burns, A.D., Frank, T., Hamill, I., and Shi, J.M. (June, January 30). The Favre averaged drag model for turbulent dispersion in Eulerian multi-phase flows. Proceedings of the 5th International Conference on Multiphase Flow, Yokohama, Japan. Number 392.
- Lopez de Bertodano, M. (1992). Turbulent Bubbly Two-Phase Flow in a Triangular Duct. [Ph.D. Thesis, Rensselaer Polytechnic Institute].
- Ramkrishna, D. (2000). Population Balances: Theory and Applications to Particulate Systems in Engineering, Academic Press.
- (2010). VDI Heat Atlas, Springer.
Cited by
Strategies and engineering aspects on the scale-up of bioreactors for different bioprocesses
de Mello, A. F. M., de Souza Vandenberghe, L. P., Herrmann, L. W., Letti, L. A. J., Burgos, W. J. M., Scapini, T., Manzoki, M. C., de Oliveira, P. Z., & Soccol, C. R. (2024) · Systems Microbiology and Biomanufacturing · doi:10.1007/s43393-023-00205-z · Cited by 117
Marchese, A., Lima, S., Cosenza, A., Giambalvo, F., & Scargiali, F. (2025) · Processes · doi:10.3390/pr13041159 · Cited by 38
“Among these factors, the distribution of light and its spectrum are considered the most critical [4].”
Deprá, M. C., Dias, R. R., Zepka, L. Q., & Jacob-Lopes, E. (2024) · Processes · doi:10.3390/pr13010051 · Cited by 31
Mink, A., Schediwy, K., Posten, C., Nirschl, H., Simonis, S., & Krause, M. J. (2022) · Energies · doi:10.3390/en15207671 · Cited by 30
“As existing models of complete PBR are highly differing in the assembly of the multi-physics simulation modules [4], a direct comparison of results is hardly possible.”
InfluentialApplication of computational fluid dynamics in optimizing microalgal photobioreactors
Amanna, B., Bahri, P. A., & Moheimani, N. R. (2024) · Algal Research · doi:10.1016/j.algal.2024.103718 · Cited by 26
Metadata
- Authors
- Luzi, G., & McHardy, C.
- Affiliations
- LSTME Busan, Busan 46742, Korea
- Technische Universität Berlin (DE)
- Corresponding author
- McHardy, Christopher
- Venue
- Energies
- Publisher
- MDPI AG
- Published
- 2022-05-27
- Volume
- 15
- Issue
- 11
- Pages
- 3966
- ISSN
- 1996-1073 (ISSN-L)
- OpenAlex
- W4281740574
- Cited by
- 44
- References
- 342
- Citations by year
- 2026: 9 · 2025: 16 · 2024: 12 · 2023: 4 · 2022: 3
- FWCI
- 2.54
- Type
- journal article
- Language
- en
- Open access
- gold
- dx.doi.org
- Licence
- Locations
- Energies (publishedVersion, cc-by-sa)
- RePEc: Research Papers in Economics (submittedVersion)
- DepositOnce (submittedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Technische Universität Berlin – Universitätsbibliothek (cc-by)
- Funders
- German Research Foundation
- Open Access Publication Fund of TU Berlin
- Topics
- Physical Sciences › Chemical Engineering › Fluid Flow and Transfer Processes › Fluid Dynamics and Mixing
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Algal biology and biofuel production
- Physical Sciences › Engineering › Computational Mechanics › Granular flow and fluidized beds
- Keywords
- photobioreactors, computational fluid dynamics, light propagation, heat and mass transfer, growth kinetics, turbulence modeling, interphase forces, population balance equation, bubble size distribution, microalgae cultivation, model validation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-07, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-07 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Modeling and Simulation of Photobioreactors with Computational Fluid Dynamics—A Comprehensive Review. https://app.cochat.ai/papers/10.3390/en15113966
- The paper
- Luzi, G., & McHardy, C. (2022). Modeling and Simulation of Photobioreactors with Computational Fluid Dynamics—A Comprehensive Review. Energies. https://doi.org/10.3390/en15113966
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.