The DOI matches its Crossref record; 31 of the 31 references it cites were found in a registry or an index.
The Influence of Manufacturing Parameters on the Mechanical Behaviour of PLA and ABS Pieces Manufactured by FDM: A Comparative Analysis
Open accessAbstract
This paper presents a comparative study of the tensile mechanical behaviour of pieces produced using the Fused Deposition Modelling (FDM) additive manufacturing technique with respect to the two types of thermoplastic material most widely used in this technique: polylactide (PLA) and acrylonitrile butadiene styrene (ABS). The aim of this study is to compare the effect of layer height, infill density, and layer orientation on the mechanical performance of PLA and ABS test specimens. The variables under study here are tensile yield stress, tensile strength, nominal strain at break, and modulus of elasticity. The results obtained with ABS show a lower variability than those obtained with PLA. In general, the infill percentage is the manufacturing parameter of greatest influence on the results, although the effect is more noticeable in PLA than in ABS. The test specimens manufactured using PLA perform more rigidly and they are found to have greater tensile strength than ABS. The bond between layers in PLA turns out to be extremely strong and is, therefore, highly suitable for use in additive technologies. The methodology proposed is a reference of interest in studies involving the determination of mechanical properties of polymer materials manufactured using these technologies.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Gibson, I., Rosen, D., & Stucker, B. (2015) · doi:10.1007/978-1-4939-2113-3 · Cited by 3,299
Anisotropic material properties of fused deposition modeling ABS
Ahn, S., Montero, M., Odell, D., Roundy, S., & Wright, P. K. (2002) · Rapid Prototyping Journal · doi:10.1108/13552540210441166 · Cited by 2,382
Additive manufacturing: scientific and technological challenges, market uptake and opportunities
Tofail, S. A. M., Koumoulos, E. P., Bandyopadhyay, A., Bose, S., O’Donoghue, L., & Charitidis, C. (2018) · Materials Today · doi:10.1016/j.mattod.2017.07.001 · Cited by 2,136
Additive manufacturing and sustainability: an exploratory study of the advantages and challenges
Ford, S., & Despeisse, M. (2016) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2016.04.150 · Cited by 1,889
Chacón, J. M., Caminero, M. A., García-Plaza, E., & Núñez, P. J. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.03.065 · Cited by 1,603
Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing
Everton, S. K., Hirsch, M., Stravroulakis, P., Leach, R. K., & Clare, A. T. (2016) · Materials & Design · doi:10.1016/j.matdes.2016.01.099 · Cited by 1,469
Mechanical characterization of 3D-printed polymers
Dizon, J. R. C., Espera, A. H., Chen, Q., & Advincula, R. C. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2017.12.002 · Cited by 1,340
Parametric appraisal of mechanical property of fused deposition modelling processed parts
Sood, A. K., Ohdar, R. K., & Mahapatra, S. S. (2010) · Materials & Design · doi:10.1016/j.matdes.2009.06.016 · Cited by 1,318
A review on additive manufacturing of polymer-fiber composites
Parandoush, P., & Lin, D. (2017) · Composite Structures · doi:10.1016/j.compstruct.2017.08.088 · Cited by 1,270
Tymrak, B. M., Kreiger, M., & Pearce, J. M. (2014) · Materials & Design · doi:10.1016/j.matdes.2014.02.038 · Cited by 1,244
Momeni, F., M.Mehdi Hassani.N, S., Liu, X., & Ni, J. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.02.068 · Cited by 1,165
Wu, W., Geng, P., Li, G., Zhao, D., Zhang, H., & Zhao, J. (2015) · Materials · doi:10.3390/ma8095271 · Cited by 881
Additive manufacturing of biomaterials
Bose, S., Ke, D., Sahasrabudhe, H., & Bandyopadhyay, A. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.08.003 · Cited by 738
Mechanical characterization of parts fabricated using fused deposition modeling
Bellini, A., & Güçeri, S. (2003) · Rapid Prototyping Journal · doi:10.1108/13552540310489631 · Cited by 628
Goh, G. D., Dikshit, V., Nagalingam, A. P., Goh, G. L., Agarwala, S., Sing, S. L., Wei, J., & Yeong, W. Y. (2018) · Materials & Design · doi:10.1016/j.matdes.2017.10.021 · Cited by 604
Sood, A. K., Ohdar, R. K., & Mahapatra, S. S. (2012) · Journal of Advanced Research · doi:10.1016/j.jare.2011.05.001 · Cited by 576
Mechanical behaviour of ABS: An experimental study using FDM and injection moulding techniques
Dawoud, M., Taha, I., & Ebeid, S. J. (2016) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2015.11.002 · Cited by 566
Mechanical property characterization and simulation of fused deposition modeling Polycarbonate parts
Domingo-Espin, M., Puigoriol-Forcada, J. M., Garcia-Granada, A.-A., Llumà, J., Borros, S., & Reyes, G. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.06.074 · Cited by 535
Effect of Infill Parameters on Tensile Mechanical Behavior in Desktop 3D Printing
Fernandez-Vicente, M., Calle, W., Ferrandiz, S., & Conejero, A. (2016) · 3D Printing and Additive Manufacturing · doi:10.1089/3dp.2015.0036 · Cited by 535
Casavola, C., Cazzato, A., Moramarco, V., & Pappalettere, C. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.11.009 · Cited by 493
Rodríguez, J. F., Thomas, J. P., & Renaud, J. E. (2001) · Rapid Prototyping Journal · doi:10.1108/13552540110395547 · Cited by 362
Yin, J., Lu, C., Fu, J., Huang, Y., & Zheng, Y. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.04.029 · Cited by 360
Xiong, J., Li, Y., Li, R., & Yin, Z. (2018) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2017.09.020 · Cited by 243
Research needs and recommendations on environmental implications of additive manufacturing
Rejeski, D., Zhao, F., & Huang, Y. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2017.10.019 · Cited by 233
Ravi, A. K., Deshpande, A., & Hsu, K. H. (2016) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2016.08.007 · Cited by 217
Deposition direction-dependent failure criteria for fused deposition modeling polycarbonate
Hill, N., & Haghi, M. (2014) · Rapid Prototyping Journal · doi:10.1108/rpj-04-2013-0039 · Cited by 164
Raster angle mechanics in fused deposition modelling
Huang, B., & Singamneni, S. (2014) · Journal of Composite Materials · doi:10.1177/0021998313519153 · Cited by 163
Tensile Properties of Processed FDM Polycarbonate Material
Masood, S. H., Mau, K., & Song, W. (2010) · Materials science forum · doi:10.4028/www.scientific.net/msf.654-656.2556 · Cited by 153
Forster, A. M. (2015) · doi:10.6028/nist.ir.8059 · Cited by 152
Levenhagen, N. P., & Dadmun, M. (2018) · Polymer · doi:10.1016/j.polymer.2018.01.031 · Cited by 114
Zhao, F., Li, D., & Jin, Z. M. (2018) · Materials · doi:10.3390/ma11020288 · Cited by 86
Cited by
Wickramasinghe, S., Do, T., & Tran, P. (2020) · Polymers · doi:10.3390/polym12071529 · Cited by 1,052
Additive-manufactured (3D-printed) electrochemical sensors: A critical review
Cardoso, R. M., Kalinke, C., Rocha, R. G., dos Santos, P. L., Rocha, D. P., Oliveira, P. R., Janegitz, B. C., Bonacin, J. A., Richter, E. M., & Munoz, R. A. A. (2020) · Analytica Chimica Acta · doi:10.1016/j.aca.2020.03.028 · Cited by 460
A review on the various processing parameters in FDM
Solomon, I. J., Sevvel, P., & Gunasekaran, J. (2021) · Materials Today: Proceedings · doi:10.1016/j.matpr.2020.05.484 · Cited by 430
Lay, M., Thajudin, N. L. N., Hamid, Z. A. A., Rusli, A., Abdullah, M. K., & Shuib, R. K. (2019) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2019.107341 · Cited by 393
Optimisation of Strength Properties of FDM Printed Parts—A Critical Review
Syrlybayev, D., Zharylkassyn, B., Seisekulova, A., Akhmetov, M., Perveen, A., & Talamona, D. (2021) · Polymers · doi:10.3390/polym13101587 · Cited by 352
Metadata
- Authors
- Rodríguez-Panes, A., Claver, J., & Camacho, A. M.
- Venue
- Materials
- Publisher
- MDPI AG
- Published
- 2018-08-01
- Volume
- 11
- Issue
- 8
- Pages
- 1333
- ISSN
- 1996-1944 (ISSN-L)
- OpenAlex
- W2885435251
- Cited by
- 477
- References
- 31
- FWCI
- 19.44
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.