Study of the Influence of the Reprocessing Cycles on the Final Properties of Polylactide Pieces Obtained by Injection Molding
Open accessThe DOI matches its Crossref record; 5 of the 5 references it cites were found in a registry or an index.
Abstract
This research work aims to study the influence of the reprocessing cycles on the mechanical, thermal, and thermomechanical properties of polylactide (PLA). To this end, PLA was subjected to as many as six extrusion cycles and the resultant pellets were shaped into pieces by injection molding. Mechanical characterization revealed that the PLA pieces presented relatively similar properties up to the third reprocessing cycle, whereas further cycles induced an intense reduction in ductility and toughness. The effect of the reprocessing cycles was also studied by the changes in the melt fluidity, which showed a significant increase after four reprocessing cycles. An increase in the bio-polyester chain mobility was also attained with the number of the reprocessing cycles that subsequently favored an increase in crystallinity of PLA. A visual inspection indicated that PLA developed certain yellowing and the pieces also became less transparent with the increasing number of reprocessing cycles. Therefore, the obtained results showed that PLA suffers a slight degradation after one or two reprocessing cycles whereas performance impairment becomes more evident above the fourth reprocessing cycle. This finding suggests that the mechanical recycling of PLA for up to three cycles of extrusion and subsequent injection molding is technically feasible.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Photodegradation and photostabilization of polymers, especially polystyrene: review
Yousif, E., & Haddad, R. (2013) · SpringerPlus · doi:10.1186/2193-1801-2-398 · Cited by 1,503
Carrasco, F., Pagès, P., Gámez-Pérez, J., Santana, O. O., & Maspoch, M. L. (2010) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2009.11.045 · Cited by 738
Liu, Z., Wang, Y., Wu, B., Cui, C., Guo, Y., & Yan, C. (2019) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-019-03332-x · Cited by 469
Biodegradation in Soil of PLA/PBAT Blends Compatibilized with Chain Extender
Palsikowski, P. A., Kuchnier, C. N., Pinheiro, I. F., & Morales, A. R. (2018) · Journal of Polymers and the Environment · doi:10.1007/s10924-017-0951-3 · Cited by 247
Sekiguchi, T., Saika, A., Nomura, K., Watanabe, T., Watanabe, T., Fujimoto, Y., Enoki, M., Sato, T., Kato, C., & Kanehiro, H. (2011) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2011.03.004 · Cited by 168
Cited by
Review on the Degradation of Poly(lactic acid) during Melt Processing
Velghe, I., Buffel, B., Vandeginste, V., Thielemans, W., & Desplentere, F. (2023) · Polymers · doi:10.3390/polym15092047 · Cited by 146
Finnerty, J., Rowe, S., Howard, T., Connolly, S., Doran, C., Devine, D. M., Gately, N. M., Chyzna, V., Portela, A., Bezerra, G. S. N., et al. (2023) · Journal of Composites Science · doi:10.3390/jcs7040141 · Cited by 66
Recyclability of Poly(Hydroxybutyrate-Co-Hydroxyhexanoate) (PHBH) for Food Packaging Applications
Plouzeau, M., Belyamani, I., Fatyeyeva, K., Marais, S., Kobzar, Y., & Cauret, L. (2023) · Food Packaging and Shelf Life · doi:10.1016/j.fpsl.2023.101170 · Cited by 41
Muñoz-Shugulí, C., Morán, D., Velásquez, E., López-Vilariño, J. M., & López-de-Dicastillo, C. (2025) · Polymers · doi:10.3390/polym17182542 · Cited by 17
Metadata
- Authors
- Agüero, A., Morcillo, M. D. C., Quiles-Carrillo, L., Balart, R., Boronat, T., Lascano, D., Torres-Giner, S., & Fenollar, O.
- Venue
- Polymers
- Publisher
- MDPI AG
- Published
- 2019-11-20
- Volume
- 11
- Issue
- 12
- Pages
- 1908
- ISSN
- 2073-4360 (ISSN-L)
- OpenAlex
- W2990075833
- Cited by
- 141
- References
- 5
- FWCI
- 3.85
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Study of the Influence of the Reprocessing Cycles on the Final Properties of Polylactide Pieces Obtained by Injection Molding. https://app.cochat.ai/papers/10.3390/polym11121908
- The paper
- Agüero, A., Morcillo, M. D. C., Quiles-Carrillo, L., Balart, R., Boronat, T., Lascano, D., Torres-Giner, S., & Fenollar, O. (2019). Study of the Influence of the Reprocessing Cycles on the Final Properties of Polylactide Pieces Obtained by Injection Molding. Polymers. https://doi.org/10.3390/polym11121908
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.